REPAIRS TO TOILETS KITCHEN FLOORING AND OTHER B AND R WORKS TO ORs JCOs MD ACCN AND PERIODICAL SERVICES TO OFFRs JCOs ORs MD ACCN UNDER AGE B AND R II OF GE CENTRAL BANGALORE

Amount

Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etc and removal of debris outside MoD land and depositing where directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed.

All as per item 3 here-in-above but exceeding 1.5 Sqm but not exceeding 4 Sqm each

Taking down shutter of any description exc 1Sqm but not exc 2 Sqm each and stacking at site where directed

Taking down shutter of any description exceeding 1 Sqm but not exceeding 2 Sqm each & refixing in the same or different opening as ordered complete all as diredcted.

Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, platform, aprons etc., laid, bedded and pointed in any mortar , stacking serviceable slbs at site and removal of entire debris as ordered outside MOD land complete all as directed.

M & L for PCC 1:5:10, type E2 using 40 mm graded crushed stone aggregate as in foundation filling mass concrete or in sunken complete all as specified and directed

Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO, Acco Proof, Impermo, Aqua flex as approved.

M & L for plain fillets of 2nd class hard wood exc 13 but n.exc 25 Sqcm in section square, rectangular or triangular in section, cleanswan secured with nails complete all as directed.

S&F solid PVC door frame of size 50X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification all as directed.

S&F 30 mm thick Flush shutters, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified.

S & F in repairs 18-20 mm WPC (Wood polymer composite) board with both side decorative face fixed in repairs to built in cupboard/ward robe partitions, shutters,cabinets pelmet boxes,wall mounted cabinets,drawers etc complete all as specified and as directed

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed..

S & F for powder coated aluminium frame for doors, windows, ventilators, powder coated of any color (tickness of powder coating not less than50 micron) with one or more rebates including cleat for fixing etc complete all as specified and directed

S&F powder coated aluminium window and ventilator shutters, three track type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed

S&F100 mm size butt hinges, medium weight, stainless steel and fixed .

S & F 200 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S&F 200 mm size extruded aluminium alloy handles (ISI Marked) fabricated type anodised and fixed.

S&F 100 mm size extruded aluminium alloy handle (ISI Marked) cast type anodised and fixed.

S&F in repair continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws complete all as specified and as directed

S&F 25mm dia stainless steel matilic coated type curtain rods with rings complete all as directed.

S&F brass chromium plated type curtain brackets suitable for 20 mm dia curtain rod along with wooden support complete all as directed.

S & F 2 lever mortice lock suitable for drawer of size 50mm complete all as specified

S & F magnetic ball catcher with striking plate of size as ordered including latting in & fixed complete all as specified

S&F stainless steel wire cloth 0.24 mm nominal dia of wire and average width of aperature 1.40mm and fixed with stainless steel wire staples including supply & fix second class hard wooden fillet, wrought , cross sectional area exceeding 3 Sqcm but n.exc 6 Sq cm fixed with nails complete all as directed.

All same as per item No 27 here-in-above but in repairs -do-

Treatment to sunken floor slab comprising the stage wise treatment as under : (i) Cleaning of the sunken / lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chiseling out any mortar sticking to the surface and brooming / washing completely & laying 40 mm average thick PCC 1.2.4 type B0 using 12.5 mm graded crushed stone aggregate as in padding concrete to achieve proper slope including 50 mm dia 350 mm long medium grade GI pipe spouts with wire gauge on inside mouth to be fixed.(ii) After the concrete is surface is completely dried rendering the surfaces with 10 mm thick CM 1.4 mixed with integral water proofing compound of Ultra Tech WP+ 200 or other equivalent etc complete & later after the surface is completely dried and in presence of Engineer-in-charge fill the entire sunken portion with water for minimum three days to check dampness and seepage where dampness and sweepage noticed nozzles shall be fixed and grouting carried out without any extra cost to Govt.(iii) All junctions points of side3 wall where CI / GI pipes are passing through shall be seated with epoxy putty.(iv) After drying putty wash the slab and sides of sunken porting with water and make it clean and clear.(v) Applying two coat polymer modified cementious water proofing coating as per manufactures instructions to bottom and vertical sides up to finished floor level + 100 mm height. The thickness of two layer shall be 1 mm. When the second layer is still sticky, coarse sand spry shall be carried out or vertical and bottom surface of the sunken portion all as specified and directed.(vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20 mm thick CM 1:4 mixed with integral water proofing compound @3% wt of cement consumed as per manufacturer’s specification including rounding of corners and junctions sloping towards spout. (WPC shall be measured & paid separately).Note :- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of Engineer-incharge. Test shall be done in presence of Engineer-in-chare or his representative and record for each sunken slab shall be maintained. The treatment shall be carried out by authorized applicators of chemicals as ordered & Cost for above stage wise activity & testing is included in the rates quoted above.

M & L non-skid coloured joint free ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified.

M & L non-skid coloured joint free ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified.

All same as per item No 31 here-in-above but on skirtings with 10 mm thick CM 1:4 -do-

M&L coloured glazed ceramic tiles of size 350x250x7mm / 450x350x7 mm thick, on verticals surfaces, set and jointed in neat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all directed.

M&L for Light shade Virified Ceramic tiles of 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15 mm thick in cement mortar 1:4 thick complete all as specified and directed.

All as per item No. 34 above but as in skirting in cement mortar 1:3 -do- (Note for item Nos 30 to 35 : i) Quoted rate is deemed to be inclusive of cement screed. ii) Shade / pattern / Colour of tiles shall be got appproved before procurement).

M&L for 18- 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite , laid over and including 15 mm thick screed bedding in cement mortar 1 : 6 all as specified & directed.(Note: Quoted rate is deemed to be inclusive of cement screed.)

M&L for Machine pressed factory made chequered cement concrete tiles, 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & pigment, laid over & including 20mm thick screed bed in cement & sand mortar 1:6, complete all as specified & as directed (Note : i) Quoted rate is deemed to be inclusive of cement screed. ii) Colour of tiles shall be got appproved before incorporation in the work)

M&L for rendering 15 mm thick in CM 1:6 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified.

M&L for rendering 10 mm thick in CM 1:3 on concrete surface as in ceiling finished the surface even and smooth without using extra cement & finally applying three coats of white wash to plastered surface of ceiling after necessary prepration of surface complete all as specified.(Note : Quoted rate is deemed to be inclusive of Three coats of white wash).

M & L for Rendering 15 mm thick in cement mortar 1:4 on brick / stone or concrete surface mixed with WPC @ the weight of minimum 3% by weight of cement mixed or as per manufacturer instruction , and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC measured and paid separately.)

M&L for providing & applying 1 mm thick wall care putty on wall /ceiling over plastered surface & prepare the surface even & smooth to the entire satisfaction of Engineer-in-charge .

M&L preparing new plastered wall surfaces of walls and applying two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, & applied as per manufacturer's instructions complete all as directed.

M&L preparing new plastered surfaces of celing and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified.

M&L for preparation of old decorative surfaces of wall including, cornices (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and washing and applying one coat of cement base paint by mechanical means / auto roller complete all as directed.

M&L for preparation of old decorative surfaces of wall including, cornices (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and washing and applying two coats of oil bound distemper over a coat of alkali resistant primerincluding necessary scaffoldings & saftey measures as required complete all as directed.

All as per item No 45 here-in-above but one coat of OBD -do-

M&L for preparation of old decorative surfaces of ceiling (plastered or unplastered) of any description, rubbing, scrapping by hand held sander / long handle sander and washing and applying one coat of oil bound distemper including necessary scaffoldings & saftey measures as required complete all as directed.

Material & Labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces applied by mechanical means i.e Airless spray including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed.

Complete removal of any type of existing treatment from walls surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces applied by mechanical means i.e Airless spray including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed.

S & F sheet glass 4mm thick ordinary quality and glazing with oil putty or wooden beads in square exc. 0.5 sqm in each pane complete all as directed.

S&F sheet glass 4 mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane complete all as directed.

M & L One coats of 1st quality synthetic enamel paint on old pained wooden surface of any description over 10 cm in width or girth including necessary preparation of new wooden surface complete all as directed.

All as per item No 52 here-in-above but on steel surface -do-

M&L for preparing new or previously untreated surface of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparing old or previously treated surface of any surface , over 10cm in width or girth and applying one coats of synthetic enamel paint etc complete all as specified and directed.

Taking down old rusted / wornout 15 mm bore GI tubing after necessary disconnection & S&F new 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.

S&F in repair 15mm dia cast copper alloy Bib taps fancy type , with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as directed.

S&F in repairs 15mm bore Stop valve /Angle cock , fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union

S & F in repair 2 way bib cock double handle with flange, cast copper alloy chromium plated, screwed down, suitable for 15mm bore iron pipe. Make: PRAYAG Cat No P6812 or equvelent of Make Hindware/Parryware/CERA

S&Fin repair health faucet ABS body with wall hook and 1.5 metre long SS braided rubber hose pipe and wall hook mounted type complete. Make: Prayag Cat No BEA-40 or equivalent in approved make.

S&F in repairs mild steel chromium plated grating 125mm dia of weight not less than 50gm with or without waste hole fixed to existing floor trap / Nahani trap with white cement complete all as directed.

S&F in repairs brass chromium plated shower rose of 100 mm size suitable for 15 mm bore of pipe including shower arm complete all as directed.

S&F in repairs PVC waste pipe of size 32/40 mm dia for WHB/Sink

S & F in repairs PVC connection pipe with PTMT nuts, 450mm long complete all as specified

S&F in repair CP soap dish, approximate size 160x160x90mm fixed to plugs with chromium plated (CP) brass screws complete all as directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed on wall with PVC rawl plug & cadmium plated brass screws, complete all as directed

S&F in repair bathroom mirror cabinet (PTMT) of size 430 x 330 mm fixed on wall with cadmium plated brass screws all as directed. Make :- Prayag (Cat Part No. 551) or equivalent of Commander (Jasmine) / Polytuf / Jindal / Parryware

&F in repairs stainless steel Kitchen plate rack of overall minimum size 900mm x 750mm and 250mm deep, with partitions for small/large plates etc made out of stainless steel 24 Gauge, fixed with rawl plug and CP steel screws all as directed. Note : Weight of rack shall not be less than 6.00 Kg. Make PRAYAG Cat No P-348 or equivelent of Nirali/Diamond

S&F sink made of stainless steel 1mm thick for Kitchen or laboratory with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 495mm x 420mm bowl size 410mm x 330mm x 160mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as directed.

S&F 550 mm X 400 mm size white flat back vitreous china wash hand basin including chromium plated pillar tap (Make: CERA Cat No. S1053101/S1053102 6502) cap stain head suitable for 15 mm bore of pipe , PVC connection 15 mm dia 45 cm long with chromium plated nuts and bolts and suitable washers, PVC waste 32 bore CP waste coupling chain and plug , porcelain stopper including CI bracket fixed in repair complete all as diirected.

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S & F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wall in repairs complete all as directed.

All same as per item No 73 here-in-above but laid on floors -do-

S&F 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed.

VP DEVELOPERS AND CONTRACTOR (BID ID -3282369)

AishwaryaConstructions (BID ID -3282464)

Sri Surya Enterprises (BID ID -3282263)

SRI KRISHNA ENTERPRISES (BID ID -3285881)