PROVN OF REST ROOM AT MOOLGAVKAR HALL AND ADDN/ ALTN TO THE CERTAIN BUILDINGS FOR HOUSING OF AR/VR BASED OPS EMPLOYMENT TOOLS AT AFA HYDERABAD

Amount

M&L for Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in Hard/Dense Soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M& L for Plain Cement concrete Type D2 1:4:8 using 40 mm graded Aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for RCC M-25 (Design mix) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC M-25 (Design mix) as in Columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for RCC M-25 (Design mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L for RCC M-25 (Design mix) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for RCCM-25 (design mix) as in Chajjas complete all as specified and as directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter surfaces complete all as specified and as directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete flat all as specified and directed.

M& L for Pre-cast cement concrete block masonry with type C1 (1:3:6) using 20 mm graded stone aggregate solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and as directed.

Providing precast cement concrete wiwth 1:3:6 type C-1 using 20 mm graded stone aggregatesolid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) set in mortar 1:4 in walls complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over cut to length bent to shape required including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia all as specified and directed.

M&L for Mild steel TMT bars 8mm dia cut to length bent to shape required including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia all as specified and directed

Ditto but as in stirrups, spaces etc

M & L for Rendering 10 mm thick on fair faces of brick work or concrete wall surfaces in CM 1:6 surface finished even & smooth without using extra cement complete all as specified.

M & L for Rendering 5 mm thick on fair faces of brick work or concrete ceiling surfaces in CM 1:3 finished even & smooth without using extra cement complete all as specified.

M & L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even & smooth without using extra cement with using WPC complete all as specified. (WPC shall be measured and paid separately).

M & L for Rendering 10 mm thick on concrete surfaces of roof in CM 1:3 surface finished even & smooth without using extra cement with using WPC complete all as specified. (WPC shall be measured and paid separately)

Supply only integral water proofing liquid complete all as specified and as directed.

M&L for applying two coats of Oil bound distemper on walls including reparation of new plastered surfaces over a coat of primer complete all as specified and as directed.

M&L for applying two coats of Oil bound distemper on ceilings including reparation of new plastered surfaces over a coat of primer complete all as specified and as directed.

M & L for Preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete all as specified and as directed.

M&L for Hardcore of gauge n exc. 63 mm, with briken stone boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M& L for 100 mm thick Plain Cement concrete Type D2 1:4:8 using 40 mm graded Aggregate as in sub base flooring complete all as specified and as directed.

M&L 25 mm thick plain Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floor finish concrete complete all as specified and as directed.

M & L for coloured Non-skid ceramic tiles (square/rectangular) 7 to 8mm thick in floors, area of each tile exc.0.11 sqm but n.exc 0.18 sqm, set and jointed in neat cement slurry and pointed in white cement mixed with matching pigment over and including 20 mm thick screed bed in CM 1:6 all as specified.

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick screed plaster in cement mortar 1:4 all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S& F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

M&L for Anodised aluminium window and ventilator shutters, top hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified

S&F 3 mm thick Figured glass, pin head type and glazing with aluminium beading in squares n.exc 0.5 sq. m in each pane all as specified and directed.

S&F 100mm mild steel butt hinges, cold rolled medium weight

S&F 100mm Aluminum anodised barrel tower bolts of extruded section all as specified and directed.

S&F 100mm extruded aluminium anodised alloy handles fabricated type all as specified and directed.

S&F 250 mm aluminum alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy all as specified and directed.

S&F vitreous china wash down water closet (pedestal pattern) white (excluding fixing bolts, flushing cistern ) with plastic water closet seat including fixing of flush pipe to pedestal pan including all joints complete all as specified and directed.

S&F 10 ltr PVC valve less, syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F Vitreous China counter top wash basin, white, square/ rectange are oval shape excluding taps, waste, chain and plug and porcelain stopper but including brackets CP waste coupling and 32mm dia waste pipe fixed and granite top all as specified and directed..

S&F of two way Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed to 15mm bore pipe all as specified and directed..

S&F 15 mm bore Pillar taps, cast copper alloy fancy type long body with swan neck with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F of concealed stop valves/angle cock 15mm dia cast copper alloy fancy type CP screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions, of 15mm bore etc complete.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F of Vitreous China urinals, half stall bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm all as specified and directed..

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and as directed

Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

Supplying and laying of 25 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

Supplying and laying of 32 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S & F PVC (SWR) pipes of 110mm dia single socketed in any length with rubber ring joints fixed to walls / floor including connections complete all as specified and as directed

S & F PVC (SWR) pipes of 75 mm dia single socketed in any length with rubber ring joints fixed to walls / floor including connections complete all as specified and as directed

S&F of 110 mm bore PVC (SWR) bends any radius all as specified and directed.

S&F of 75 mm bore PVC (SWR) bends any radius all as specified and directed.

S&F PVC 110 mm bore (SWR) junction single, (Single T) equal or unequal all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm bore all as specified and directed.

M& L for 75 mm thick Plain Cement concrete Type C1 1:3:6 (20 mm graded Aggregate) as in plinth protection laid in alternate bays not exceeding 2 Sqm each and finished fair on top without using extra cement. 6mm wide joints shall be provided throughout the thickness of plinth protection in concrete bays. All joints in bays of concrete, shall be filled with mastic filling comprising of one part of heated bitumen Vg-30 grade and 3 parts of sand (all by weight). all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm or removing the earth all as specified and directed. In hard/dense soil all as specified and directed.

Removing excavated material (soils) exceeding 1.50 km but not exceeding 5 km and depositing where directed all as specified and directed.

M&L for Plain cement concrete 1:3:6, Type C2 using 40mm graded stone aggregate as in foundation, filling and mass concrete etc., complete all as specified and directed.

S&F of Structural Steel work as columns, posts, stanchions etc using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St.-240 or with holow structural steel sections conforming to IS 4923-1997 Grade St-240 all as specified and directed.

S&F of Structural Steel work as in main and cross beams, hip and jack rafters, purlins where connected to common rafters , vertical posts, etc fixed with angle cleats or other connecting plates, cleats etc. using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St.-240 or with holow structural steel sections conforming to IS 4923-1997 Grade St-240 all as specified and directed.

S&F of Structural Steel work in tubular trusses including special shaped washer etc.. using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St.-240 or with holow structural steel sections conforming to IS 4923-1997 Grade St-240 all as specified and directed.

M&L for Rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment all as specified and directed.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated sheet 0.5mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall with self tapping screws complete all as specified and as directed.

S&F Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall with self tapping screws complete all as specified and as directed.

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide zinc crome primer on Surfaces of any description,over 10cm in width or girth, not otherwise described complete all as specified and as directed.

M&L for rendering 15 mm in Cement Mortar 1:4 on fair faces of brick work or concrete surface walls finished fair and even complete all as specified and as directed.

M&L for preparation of new surfaces plastered or unplastered walls and applying two coats of cement base paint over a priming coat all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard / dense soil.

M&L for 75 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in floor, sub base etc all as specified directed.

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M & L for providing cement concrete PCC 1:2:4 type B-1 mix using 20 mm graded stone aggregate as in kerbs, stoppers, edge stones etc including use of necessary formwork, straight or curved, finishing exposed surfaces etc complete all as specified and directed..

M&L for 150mm dia Reinforced concrete pipes, class NP2, laid and jointed with collars complete all specified & directed

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm dia NP2 pipe complete all as specified & directed.

M&L for proving cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate as in benching coping and like complete all as secified and directed.

M&L for proving pre cast reinforced cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slabs for manholes etc set in CM 1:6 complete all as specified and directed.

M&L On site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 10 Users

M & L for Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.2 M dia X 1.5 M effective depth complete all as per TD drawings and as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m

Taking down of cement plaster of any description or thickness/chipping of cement concrete in any situation from brick or concrete surface including raking out of joints, hacking for key scrubbing down with water to received new plaster complete all as specified.

Demolition of unreinforced Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as directed.

Taking down Chowkhats or frames not exc. 1.5 sq. m each but with shutters (without taking off shutters from the frames) including making good of disturbed portion with cement plaster or cement concrete type B-0 as required complete all as specified and directed.

Taking down Chowkhats or frames exc. 1.5 sq. m each but with shutters (without taking off shutters from the frames) including making good of disturbed portion with cement plaster or cement concrete type B-0 as required complete all as specified and directed.

Water proofing treatment to RCC roofs in repairs consisting of :- (i) Removing existing water profing treatment of any description, any type on roofs .Picking, sweeping, cleaning any washing down with water to remove all loose particles, dust etc complete all as directed by Engineer-in-charge. (ii) While doing the treatment on existing roof, concrete should be thoroungly inspected for any significant distress. such distress, if any repaired/rehabilitated and treated. Note: Pipes Over roof should be realigned where ever required. (iii) Cleaning the surface of roof & up to 300mm of parapet and crumple joint including junction of roof and parapet, providing and laying / fixing TPO (Thermoplastic Polyolefin) Water proofing membrane FOSROC Proofex ORG (minimum 1.2 mm thick) over a min 200 GSM Geo textile or asian Paints TPO or Equivalent product of M/s MC Bauchemic / CIPY / SIKA / Pidilite Dr Fixit / Thermax / STP applied as per manufacturer’s instructions. (iv) The work shall be carried out complete as per manufacturer’s specifications and application methodology. Execution to be done with authorised trained / skilled applicator of manufacturer as per technical guidance laid by manufacturer. Company bank guarantee to be given by contractor after completion of water proofing work before payment. Note:- (i) The rate quoted by the contractor shall be included for dismantling and refixing of pvc water tank hoisted on roof, taking down and refixing of water tubing and any other fitting on roof as required and no extra shall be paid (ii) work shall be carried out through authorised applicators of the manufacturer as per instruction.

M&L for 20mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms for counter WHB and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade complete all as specified and directed including rounding of edges as required.

M & L for Virified tiles 10 mm thick (square/ rectangular) polished any shade, double charged, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed in CM 1:6 all as specified and directed.

M & L for Virified tiles 10 mm thick (square/ rectangular) polished, any shade, double charged area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 10mm thick backing coat on vertical surfaces of wall as in skirting in cement mortar 1:4 complete all as specified and as directed.

M&L for complete removal of existing treatment on walls, including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying two or more coats of distempering with 1st quality acrylic distemper(ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and directed.

Supply and fixing factory made UPVC door frame made of UPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

S&F Supply, and fixing 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a UPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The lock rail made up of 'H' section, a UPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a UPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by insering horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineer-in-charge.

S&F powder coated aluminium frame for doors, windows, ventilators, partitions etc with one or more rebates including joining cleat for fixing etc. complete all as specified.

S &F Aluminium powder coated door shutter aluminium section weighing 0.55kg/m incl necessary joining cleats, glazing clips rubber neoprene packing handles 2 nos in each door hinges anodised aluminum snap beading screws etc complete all as specified

S & F powder coated aluminium window and ventilator shutters of Sliding type with standard aluminium sections 40 x 18mm size weight not less than 0.55Kg/Rm including rollers and necessary locking arrangement etc complete all as specified and directed.

S&F in 200mm Aluminum anodised barrel tower bolts of extruded section complete all as specified.

S&Fin repair 150mm extruded aluminium anodised alloy handles fabricated type complete all as specified.

S&F 300 mm aluminum alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy complete all as specified.

S&F 150mm Floor door stopper of brass body and tongue with hard drawn steel spring etc complete all as apecified and directed

S&F 4mm thick Figured glass, pin head type and glazing fixed in aluminium frames with rubber beading/gasket in squares n exc 0.5 sq. m in each pane complete all as specified.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with alluminium wire staples

S&F Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of mainT runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000 mm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. with fully perforated 12mm thick micro tegular edged or 10mm thick squre edged GRG False ceiling . The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge.

S&F mild steel rolled section as in framed trusses trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, pipe, channel or flat sections) including bracings, distance pieces, cleats etc. complete all as specified and directed.

M&L for preparation of new steel surface over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for preparation of old plastrered surfaces of ceiling & applying one coats of white wash complete as specified and directed

S&F 25 mm dia aluminium powder coated Curtain rails, drapery rods with fixing brackets, end knobs etc all as specified and directed

S &F 5mm thick Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specified and directed

M&L Raking out joints/ pointing to squared rubble masonry, coursed or uncoursed cement or cement lime mortar all as specified and directed.

M&L for applying two coats of cement base paint over a coat of primer including preparation of new plastered surfaces complete all as specified and as directed.

M&L for two coats of painting on existing surface of walls with 1st quality (ready mixed) approved manufacturer, of required shade and colour complete, as per manufacturer's specification.

S&F Rotational moulded PVC water storage tanks of 1000 ltrs capacity (cylindrical vertical with closed top) , two layered, hoisted and fixed in position all as specified in SSR part – I.

S&F in repair 25 mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified and directed (Minimum weight 15 mm - 142 Gms)

S&F 25mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

Supply,laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 70 sqmm 3 1/2 core (from substation 6 to prp LT panel) all as directed by Engineer in charge.

Supply,laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 6 sqmm 2 core (from prp LT panel to toilet DB) all as directed by Engineer in charge.

Supply,laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 sqmm 4 core ( From prp LT panel to TPN DB) all as directed by Engineer in charge.

M&L for Earthing complete with GI earth plate electrode of size 600x600x6.6 mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to GI wire 4 mm dia earth lead by means of nuts, bolts, check nuts, washers of galvanised iron as steel, protected by galvanized iron pipe 40mm bore (Medium grade) all as directed including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x10cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel, wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering, earth testing point, charcoal or coke and salt in alternate layers with necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion all complete as specified and directed ( GI wire upto 7.5m including testing consider in this item). Note: (i) Cost of GI earth wire and GI protection pipe upto 7.5mtr length shall be deemed to be included in the rate quoted for this item. (ii) The unit rate shall also includes for Wire mesh, funnel, excavation,returninng & filling, PCC chamber pit,RCC cover & test point (iii) PCC pit shall be provided at least 500mm away from the earth pit and not just on the earth pit.

M&L for earthing complete with Galvanised steel earth plate eletrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filled in alternate layers and electrode connections by using Galvanised earth strip 32x6mm connected by means of bolts, nuts, check nuts and washer of galvanised iron or steel, provision of 40 mm dia GI pipe medium grade for protection of GI earth strip and 20mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) type C1 chamber, MS funnel, wire mesh, 50 mm thick RCC 1:2:4 type B1 earth pit cover with 6 Nos, 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No 3 of schedule Part-I And all as directed.(Fot LT panel).Note: (i) Cost of GI strip and GI protection pipe upto 7.5mtr length shall be deemed to be included in the rate quoted for this item. (ii) The unit rate shall also includes for Wire mesh, funnel, excavation,returninng & filling, PCC chamber pit,RCC cover & test point (iii) PCC pit shall be provided at least 500mm away from the earth pit and not just on the earth pit.

Excavation in trenches n.exc 1.5 mtr wide & n.exc 1.5 m depth in soft /loose soil & getting out for laying of LT cable all as specified & directed by Engr- in Charge.

M & L Sand covering /cushioning for underground cable protection complete all as specified and directed by Engr- in Charge.

M&L for burnt bricks sub class 'B' laid perpendicular over & cushioning for cable protectioncomplete all as specified & directed at site by the Engr- in Charge.

M&L for Taking down exhaust fan of 400 mm sweep and move it to the MES store for safe keeping.alll as directed by engineer in charge

M&L for Taking down ceiling fan of 1200 mm sweep and move it to the MES store for safe keeping.alll as directed by engineer in charge

fixing or hanging only ceiling fan and connecting up including provision of cable from ceiling rose/connector to fan all as directed by engineer in charge.

M&L for Taking down carefully copper/aluminium point wirning (light,fan,socket or power ) complete including fixture and fittings such as switches,ceiling roses, pendants,regulators,lights and sockets etc and making good distrubed surfaces all as directed by engr in charge.

S&F of MCCB DB 8 way triple pole neutral vertical type double door 415 volts 50 Hz AC supply including suitable provision for 4 pole MCCB incomer, fixed to the existing wall (concealed/surface) and making good the disturbed surface wall with the exsting wall complete all as specified and as directed.

M&L for MCCB 415V adjustable type 16KA breaking capacity 4 pole 63 amps rated current all as directed by engineer in charge.

S&F of MCB DB SPN 8 way with copper bus bar & neutral link double door type to be fixed in the wall including connections and making good the disturbed surface of wall to perfectly match with the exsting wall complete all as specified and as directed.

S&F MCB SPN 6 to 32A, 10KA rupturing capacity complete all as specified and as directed.

S&F SP 5 to 32 amp rating 240V 10KA C curve miniature circuit breaker fitted in MCB DB complete with connection testing and comissioning all as directed by engineer in charge.

M & L for Point wiring with 1.5 Sqmm copper conductor unsheathed, multistranded, PVC insulated, single core cable FRLS with earth continuity conductor of 1.5 sqmm PVC insulated copper conductor and including rigid PVC conduit of suitable size but not less than 20mm dia. and all accessories fixed to be consealed in wall & surface of the roof etc., including modular type terminal boxes made out of Galvanised sheet of thickness should be not lessthan 0.9mm thick for fixing of modular switches, modular fan regulators, modular socket outlet etc along-with suitable modular plate for housing switches, etc complete all as specified and as directed. (a) One light point controlled by one switch

(b) One ceiling/exhaust Fan point controlled by one switch

(c) One three pin socket 5 Amps plug point independent

(d) One three pin socket 5 Amps plug point on same board

All as per item above but wiring with 2.5 sqmm copper cable with 2.5 sqmm for one earth continuity cable for 6 pin 15 Amp sockets outlet controlled by 15 Amp switch

S&F of Modular Switch type polycorbonate white 1 way, 6A, 240Volts complete all as specified.

S&F of Modular Socket outlet polycorbonate white 10A - 2/3 pin complete all as specified.

S&F of Modular Switch type polycorbonate white 1 way, 16A, 240Volts complete all as specified.

S&F of ceiling rose, three terminal, PVC/polycarbonate, insulated body, ISI marked complete all as specified and as directed.

S&F of Modular Socket outlet polycorbonate white 20A - 2/3 pin complete all as specified.

S&FLED light fitting 1x20 W 220 V AC decorative box type with driver, holder including LED tub light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F flush / surafce type light fittings of size 2X2 suitable for 35/36W LED complete with inbuilt driver surface mounted/recessed type slim box type luminaries with CRCA housing white powder coated finish suitable to operate with 220 V AC, complete with all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable with cross sectional area 1.0 Sqmm after removing old U/S rusted fittings complete all as specified and as directed.

S&FLED light fitting 1x10 W 220 V AC decorative box type with driver, holder including LED tub light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply & Fixing exhaust fan iron body with louvers 300 mm sweep single phase 240V AC 50 Hz and connecting up including lovers including making necessary opening on stone/brick masonary wall of suitable size finishing it properly and making good with matching colours with the surrounding provision of cable 3 core of size 0.5 Sqmm from ceiling rose to fan complete all as specified and directed.

M&L for Sub Main wiring with two runs of 6 sq mm 1100 V grade (nominal area) single core PVC insulated unsheathed cable multi-stranded copper conductor drawn through medium grade, rigid non-metallic PVC conduit concealed of suitable sizewith all necessary fittings, surface in walls/roof/floor duly earthed with one run of single core cable of same size but green in colour as continuous earthing wire and connecting to common earth dolly complete all as specified and directed by Engineer-in-Charge.

S&F install hi wall split units indoor/outdoor complete with cordless remote control unit and with inbuilt air ioniser and plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity unit air conditioner electric driven single phase of capacity of 1.5 TR all as directed by engineer in charge. Note : A.C fitted with inbuilt stabilizer.The rate includes the cost of all wires,starters and switches required.

M&L for motor starter 25 Amp 2 module including necessary metal box and cover plate all as directed.

M&L Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 240 V, 50 Hz AC complete all as directed

S&F copper refrigerant pipes for suction and discharge between inddor and outdoor units of 1.5 ton split a.c of stanadard size as per OEM recommendation with proper insulation including fixing arrangement with powder coated MS clamps and jointing of pipe etc including necessary items required all as specified and ditected by enginner in charge note :two runs of insulated copper tubing (for in and out flow) and one run of 3 core 2.5sqmm copper wire will be measured as one unit.

supply and fix PVC pipe 25mm dia low density polyethylene of pressure 6 kgf/cm2 for Acs drain water ,including tees bends reducers for leakage free jointing etc including clamps and other material for fixing on wall/cemented surface at a height of 20 to 30 feet al as specified and directed by engineer in charge.

S&F of Modular Switch 1 way 1 module polycorbonate white, 6A, 240Volts complete all as specified and directed by Engr-in-Charge.

S&F of Modular Switch 1 way 1 module polycorbonate white, 16A, 240Volts complete all as specified and directed by Engr-in-Charge.

S&F of Modular Socket, 6A - 2/3 pin combined 2 module, 240Volts complete all as specified and directed by Engr-in-Charge.

S&F of Modular Socket 6A/16A - 2/3 pin combined 2 module, 240Volts complete all as specified and directed by Engr-in-Charge.

S&F of stepped type polycorbonate white electronic fan regulator flush type 2 module all as specified and as directed.

S&F surface mounting/wall mounted LED tube light fitting 10watts high efficiency, anti glare, maintenance free operation including LED driver and mounting arrangements, all accessories internally pre-wired, connecting up with twin core twisted flexible copper conductor cable white colour with suitable size complete all as specified and directed by Engineer-in-Charge.Make Bajaj Model BCLSB 10 W WH or equivalent

Supply and Fix 1X36 to 40W high efficiency 2X2 recess mounting LED light fitting with glare free homogeneous illumination including LED driver with all accessories for mounting internally pre-wired, connecting up with three core twisted flexible copper conductor cable complete all as specified and directed by Engineer-in-Charge.

Supply and fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, sweep 250 mm including louvers and making good with matching colour with the surroundings provision of cable 3 core of size 0.5 Sqmm (16/0.2 mm) from ceiling rose to fan, all as specified and as directed.Make -Havells -Model Ventilair DX or Equivalent

M&L for Sub Main wiring with 2x4 Sqmm 1100 V grade (nominal area) single core PVC insulated unsheathed cable multi-stranded copper conductor drawn through medium grade, rigid non-metallic PVC conduit of size 25mm or higher suitable size with all necessary fittings, concealed in walls/roof/floor duly earthed with 1X4 Sqmm of single core cable but green in colour as continuous earthing wire and connecting to common earth dully complete including taking down old submain wiring all as specified and directed by Engineer-in-Charge.

S&F of MCB DB 4 way SPN double door powder coated, 230volts 50 Hz AC supply including fixing to the existing wall (concealed/surface) and making good the disturbed surface wall with the exsting wall complete all as specified and as directed.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DBs Complete with connection testing and commissioning. complete all as specified and as directed.

S&F dummy PVC cover (blanking plates) for existing MCB DBs complete all as specified and as directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning SPN 32 AMP. complete all as specified and as directed.

M/s RAMA LAKSHMI CONSTRUCTIONS (BID ID -3095282)

NEWS CONSTRUCTIONS (BID ID -3098200)