Construction of Jharotha Sub station and 33 and 11 KV Lines

Amount

SUB-STATION PART:- 33 KV Line Isolator.

33 KV Bus Isolator.

33 KV Lightening Arrestors

33/11 KV Transformer 5 MVA

33 KV VCB 800A, 750MVA with Steel structure

Control panel I/C for 33 KV single T/F

Control panel I/C for 33 KV double T/F

33 KV CT 400/200/1-1A

33 KV CT 200/100/1-1A

33 KV 1 Ph PT 33 KV/110 V

11 KV SWITCH GEARS VCB:- (i) Incoming VCB 600/300/5A, 350MVA, I /C

(ii) Outgoing VCB 200/100/5A, 350MVA

(iii) Bus coupler 350 MVA

11KV 3 Core XLPE Cable:- (i) 3 × 300 Sq.mm

(ii) 3 × 185 Sq.mm

11KV Cable jointing kit. Heat Shrinkable:- (i) 300 Sq.mm Indoor

(ii) 300 Sq.mm Outdoor

(iii) 185 Sq.mm. Indoor

(iv) 185 Sq.mm. Outdoor

11/0.4 KV, 63 KVA Transformer.

PCC Pole 8.5 mtr. Long for Switch yard Lightening

33 KV Terminal Gantry with Plinth & Foundation as per RESSPO Schedule

Main Bus Bar complete with Structure. Plinth & Foundation as per RESSPO Schedule

Structure for Line & Bus Isolator. with Plinth & Foundation

33 KV Post Insulator

Structure for Post Insulator with Plinth & Foundation

Structure for Lightening Arrestors with Plinth & Foundation

90 Lbs. Rail pieces for T/F

CT Steel structure with Plinth & Foundation

Structure for P T with Plinth & Foundation

33 KV Fuse Set

Structure for fuse Set with Plinth & Foundation

24 V Battery with Battery Charger and Cabinet.

Copper Control cable (Armoured) :- (i) 4 × 2.5 Sq.mm.

(ii) 2 × 2.5 Sq.mm.

L.T. Cable Al. 3.5 × 70 Sq.mm .

Earthing of Sub-Station:-(As per RESSPO Schedule) (i) Outdoor Equipment (Earth Mat)

(ii) Indoor Equipment (Earth Mat)

Pipe Earthing of Power Transformer by way of boring and lowering of "B" class G.I. pipe 50 mm. dia. Into the ground up to the water lever to the lower end of which a solid copper con approx 9 inches long and 750 gram in weight provided and screwed in connecting and bringing out continuous copper wire 8 SWG from the cone to the ground surface where it will be bolted to the G.I. Earth strip for transformer neutral connection. The earth strip will be welded to the G.I. pipe. The work also includes cap and clamp for pouring water, the cost of all material with all labour and T&P etc. complete in all respect.

Chemical Pipe Earthing as per DVVNL approved G.T.P.

Plinth of Power T/F 3.5x4.5 Mtr. 0.5 m below and 0.7 m above in ground level with cross bricks boundry colomn . 6.0 Inch RCC Lenter on the plinth. As per drawing

Plinth & Foundation of 33 KV VCB

11 KV Cable laying Including cost of sand and Bricks

SWITCH YARD LIGHTING ARRANGMENT Stone Pad -6 No PVC Cable 2×10 mm2 armor for switch Lighting -200 Mtr PVC conduct pipe for PVC cable- 150 Mtr Change Over Main Switch 63 Amp. for three phase supply -01 No. Concreting of supports - 6 No. Sun mica Board Including (MCB Box - 1 no., three phase for wire- 2 No., Red yellow Blue Bulb including Holder and wiring)- 1 Job LED Light 100 W (ISI Mark) -8 No. 15 Amp. LED Light Contral Switch Button - 8 No.

Fabrication and grouting of G.I. Channel 100x50x6 mm. in L shape & in proper size and alignment to provide support for the two separate Earthing strips for power transformer neutral including supply & fixing of two nos. flexible copper bonds for neutral Earthing. The work also includes painting of G.I. Channel with two coats of aluminium paint.

33 KV Polymer Pin Insulators

11 KV Polymer Pin Insulator

MS Channel (100x50x6) mm, @5.8 Kg/M

Copper Bus Bar size 80x8 mm-2.4 Mtr. Long

A.C.S.R. Panther conductor

PG Clamp Panther to Panther Conductor

MS Angle (50x50x6)mm

Making of 11 KV Cable Box (300/185 sq.mm J/K).and mounting on Switch Gear and Transformer

Fabrication and erection of cable support made of two pieces of G.I. 65x65x6 mm. 4.0 mtr. Long 1.0 m grouted in depth, joined to each other by means of 5 Nos. M.S. flat 50x6 mm. pieces of size 150 mm. long each by welding at equal intervals as per drawing and grouting in a block of size 300x300x700 mm. complete with two coats of Aluminium paint. This includes providing of four nos. G.I. clamp made of G.I. flat for holding the cable including Nuts & Bolts.

Painting of Sub-Station structure & Equipment

Exhaust Fan Complete in every respect for control room

T&P of Substation of switchgears ( Magger 5 KVA Digital type - 1 Nos., Screw Driver Set., Rinch Paana Set., Nut Boult Opener Complete Tool Kit, 33 KV Hand Gloves- 2Nos., Plier, Conductor Cutter, LED Charge able Tourch, Earth Tester, Earthing Chain, Discharge Rod for Earth of line - 2 No., Hygrow Meter for Check Gravity of Battery Water, Continuity Tester, Tong Tester etc.

Cost of Misc. Items i.e. Rubber Matting, Single Line Diagram Board, Tripping Chart Board, S/S Name Board and painting of SS Name at control room wall etc.

Fire Fighting equipments including 02 Nos. 4.5 Kg. Co2 Fire Extinguisher potable type and 02 Nos. Foam type Fire Extinguisher potable type

Fire Bucket stand size 1500x1200mm. having M.S. Channel 100x50 mm base with cross triangular bracing of M.S. Angle 50x50x6 mm and base of 100x50 mm. Channel 600 mm long having pipe 25 mm and boxing pipe of size 32 mm. including welded with M.S. hooks rigidly and nicely painted with one coat of red oxide primer & two coat of red enamel paint of best quality.

Fire bucket made of B.P. sheet 20 gage ( conical shape ) having capacity 10 Ltr.- 10” dia with bar handle for hanging of bucket including nicely painted in inner portion with one coat of red oxide primer & two coat of channel white paint & outer side with one coat of red oxide primer & two coat of post office red colour & written work “AAG” in Hindi.

Substation Furniture (4–Chairs,2-Office chair, 2–Table, 1–Steel Bench, 1–Steel Rack Long size)

Survey and lay out of Sub-station

Sundries Charges

Testing & commissioning charges of Substation.

33 KV LINE PART:- PCC Pole 9.0 Mtr. Long

11 Mtr. long S.T. Pole

13 Mtr. long S.T. Pole

33 KV Polymer Pin Insulator

Earthing complete

33 KV Polymer Disc Insulators B&S Type 70KN

Disc Fittings for Dog/Raccoon 70KN

33 KV "V" Type Cross Arm 100x50x6 mm. M.S. Channel

33 KV "V" Type Cross Arm Holding Clamp with nuts & Bolts

A.C.S.R. DOG CONDUCTOR

Stone Pad

Barbed wire

The Grouting and making of plinth of the support (1/6 of the full length of the supports) will be done as per norms in the CC 1:4:8 with cement, course sand and brick ballast including back filling and proper ramming.fixing of all clamps and other accessories as per relevant drawing. i) 9.0 Mtr. Long PCC poles

ii) 11 Mtr. Long poles

iii) 13 Mtr. Long poles

Holding Clamp for ST Pole

Number Plate with clamp. and N & B

Danger Board with clamp. and N & B

33 KV Stay Set Complete (G.I STAY ROD , 20X1800 MM ,STAY WIRE 7/8 SWG, STAY CLAMP,BOLT NUT & WARSHER)

Grouting of Stay Rods 20x1800 mm. including all works of excavation, fixing, tightening & nozzling of stay with the poles and of required tension as per relevant drawing including back filling of earth and proper ramming.

M.S. Bolts, Nuts & Washers

Aluminum Paint

Red Oxide

Top Channel 125x65x3200 mm. with Clamps

P.G. Clamp for Dog Conductor

‘F’ Bracket for 33 KV

‘E’ Bracket for 33 KV

Droper Channel 100 x 50 x 3000 mm.with .Clamps. ( for Cable supporting )

Stay Clamp for Stud Pole

G.I. wire 6 SWG

G.I. wire 8 SWG

MS Angle 65x65x6 mm. for Guarding Angle

Bracing set 4.3 x 4.3 Mtr Angle Iron 65x65x6 mm with holding clamp

Cross-Arm Holding Angle with clamp 65x65x6 mm., 1600 mm. Long

HDPE Pipe PN-6, PE-100, DN-160 mm. Dia Pipe for laying of 33 KV

33 KV 3x300 XLPE Cable

H/S O/D 33 KV 3x300 sq.mm. J/kit

Cable Route Marker

G.I. Pipe 160 mm. Dia

Holding Clamp for GI Pipe

Holding Clamp for Cable

Lug for ACSR Dog Conductor

Choping of branches of Tree

Underground Cable Work :- Laying of 33 KV Cable in Air

Laying of HDPE Pipe, PN-6, PE-100, DN-160mm dia Pipe for laying of 33KV, 3x300Sq.mm, XLPE Cable with HDD (trenchless) method including cable laying.

Digging & laying of 33 KV Cable in trench with sand & brick

Making of 33 KV 3x300 sq.mm. Jointing/kit for 33 KV XLPE Cable

11 KV LINE PART:- 8.5 Mtr. long PCC Pole.

11 Mtr. long S.T.P., SP-55 Pole.

13 Mtr. long S.T.P., SP-72 Pole.

11 KV "V" type cross arm 65x65x6 mm, M S Angle

Clamp for 11 KV "V" type Cross arm with bolts and nuts

F-bracket for 11 KV

E-bracket for 11 KV

11 KV Polymer Pin Insulator

Earthing complete

11 KV Disc Insulators T&C Type 45KN

11 KV Disc fittings T&C Type 45KN

Stay set Complete for 11 KV line

Grouting of stay rods 1800 x 20 mm. including all works of excavation, fixing, tightening & nozzling of stay with the poles and of required tension as per relevant drawing including back filling of earth and proper ramming.

Stay Clamp for Stud Pole

11 KV Lightning arrestor

Stone Pad 300x300x75 mm

Barbed wire

The Grouting and making of plinth of the support (1/6 of the full length of the supports) will be done as per norms in the CC 1:4:8 with cement, course sand and brick ballast including back filling and proper ramming.fixing of all clamps and other accessories as per relevant drawing. i) 8.5 Mtr. Long PCC Poles

ii) 11 Mtr. Long poles

iii) 13 Mtr. Long poles

Number Plate with clamp and N & B

11 KV Danger Board with clamp and N & B

Alluminium Paint

Red Oxide

Top Channel 100x50x6 mm., 2240 mm. Long

Dropper Channel 100×50×6 mm., 2028 mm Long

Bracing set 2.7 x 2.7 Mtr Angle Iron 65x65x6 mm. with holding clamp

Guarding Angle 65x65x6 @ 5.8 Kg/M (for single pole 2300 mm., for DP/TP 3600 mm. Long)

G.I. wire 6 SWG

G.I. wire 8 SWG

Holding clamp for Guarding Angle

Holding clamps for Top Channel with Nut & Bolts

PG clamp for Dog/Raccon Conductor

M.S. Nut & Bolt with Warshers

MS T-Off Channel 100x50x6 x 1300 mm. with clamp

MS T-Off Channel Holding Angle

ACSR Raccon Conductor

M.S. Angle 65x65x6 mm,2028 mm. long for G.I. Pipe supporting @ 5.8 Kg/M

11KV TPMO Set. with fixing clamp complete

11 KV DO Fuse Set with Fixing clamp complete

Clamp for TPMO & Fuse Set etc.

Copper L-Piece of size 50x6 mm for LT bushing Rod of 63 KV transformer

LT Aluminium insulated Cable of size 1x16 Sq.mm. (for HT jumpering)

Al. crimping lugs:- Al. crimping lugs 50 sq.mm.

Al. crimping lugs 120 sq mm.

Al. crimping lugs 185 sq.mm.

SMC MCCB Distribution board for 63 KV Transformer

G.I.Pipe 160 mm Dia for Double Pole Structure

Choping of branches of Tree

Carriage of following material from Center Store to Site SUB-STATION PART:- 33/11 KV Transformer 5 MVA

33 KV VCB 800A, 750MVA with Steel structure

Control panel I/C for 33 KV single T/F

Control panel I/C for 33 KV double T/F

33 KV CT 400/200/1-1A

33 KV CT 200/100/1-1A

33 KV 1 Ph PT 33 KV/110 V

11 KV SWITCH GEARS VCB:- (i) Incoming VCB 600/300/5A, 350MVA, I /C

(ii) Outgoing VCB 200/100/5A, 350MVA

(iii) Bus coupler 350 MVA

11KV 3 Core XLPE Cable:- (i) 3 × 300 Sq.mm

(ii) 3 × 185 Sq.mm

11/0.4 KV, 63 KVA Transformer.

PCC Pole 8.5 mtr. Long for Switch yard Lightening

33 KV LINE PART:- PCC Pole 9.0 Mtr. Long

11 Mtr. long S.T. Pole

13 Mtr. long S.T. Pole

A.C.S.R. DOG CONDUCTOR

33 KV 3x300 XLPE Cable

11 KV LINE PART:- 8.5 Mtr. long PCC Pole.

11 Mtr. long S.T.P., SP-55 Pole.

13 Mtr. long S.T.P., SP-72 Pole.

ACSR Raccon Conductor

M/S ANURAG MISHRA CONTRACTOR & SUPPLIER (BID ID -5571088)

PREMIER ENGINEERING COMPANY (BID ID -5536704)