supply of material for Construction of Visitors Shed, Godown (2 No.) and Control Room at Distt. Jail Gonda

Amount

Supply of Pozonolla portland cement as per ISI code 1489-2015 (Prism, Birla, ACC, JYPEE of equivalent) every bag shall be deemed to contain 50 Kg of cement. The suppliers may liable to submit test report. Including loading, carriage, unloading and stacking at site

Supply of Coarse sand shall be clean sharp and free from clay, loam, organic or any other foregin matter, shall be obtained from approved Hamirpur quarry. The contractor shall get the sample of coarse sand approved by the Engineer-incharge. Sand which in the opinion of the Engineer in charge of his or his representative. If dirty must be washed to his satisfaction at the cost and expanses of the contractor coarse sand shall pass through a mesh. 4.75 mm square measured in the clear. Sand shall not be used for concrete works if it contains more than 10 % of fine grains passing through a 76 mesh sieve. should the fineness modules be less than 2.25 unless specific permission is obtained from the Engineer in charge. Including loading, carriage, unloading, royalty and stacking at site.

Supply of Brick class M-150 shall be of approved quality of standard specification (size 230x110x70 mm) including loading, carriage, unloading and stacking at site.

Supply of 20mm guage stone grit shall be hard of uniform and fine texture.free form faults or planes of weakness and free from weathered faces. The ballast/ grit or chips must be free from loam, clay or any surface coating, free from organic matter or other impurities and screened, free of dust. Grit/ ballast shall be obtain from approved kabarai quarry. Stone aggregates from other sources may also be used provided the same is found suitable in the opinion of the Engineer-in-Charge. The opinion of Engineer-in-Charge must be recorded in writing. The ballast or chips shall be obtained by breaking from large blocks and must be more or less cubicle in shape stone grit grading shall be in conformity with the requirements laid down in the Indian Standards Specification. Including loading, carriage, unloading, royalty and stacking at site

Supply of 40mm guage stone grit shall be hard of uniform and fine texture.free form faults or planes of weakness and free from weathered faces. The ballast/ grit or chips must be free from loam, clay or any surface coating, free from organic matter or other impurities and screened, free of dust. Grit/ ballast shall be obtain from approved kabarai quarry. Stone aggregates from other sources may also be used provided the same is found suitable in the opinion of the Engineer-in-Charge. The opinion of Engineer-in-Charge must be recorded in writing. The ballast or chips shall be obtained by breaking from large blocks and must be more or less cubicle in shape stone grit grading shall be in conformity with the requirements laid down in the Indian Standards Specification. Including loading, carriage, unloading, royalty and stacking at site

Supply of Fine Sand 1.25 FM. including loading, carriage, unloading, royalty and stacking at site

Supply of Local Sand including loading, carriage, unloading, royalty and stacking at site

Supply of TMT bar 8 to 20 mm dia, Fe-415 conforming to IS code 1786-1985 including carriage loading unloading & stacking complete in all respects.

Supply and fabricating of Angle iron chaukhat (40x40x5mm), grill 10 mm sq bar & Z-section window & purlin for trusses including loading, carriage, unloading and stacking at site

Supply of precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single ength upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including loading, carriage, unloading and stacking at site.

Add GST as applicable

PRAYAG CONSTRUCTION COMPANY