ADDITION/ ALTERATION TO LOGISTIC SECTION AND IMPROVEMENT TO BUILDING P-13 AT HQTC BANGALORE

Amount

Demolition of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dresses stonework and precast concrete articles complete all as specified and as directed by Engr-in-charge.

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation, etc., and getting out in soft/loose soil complete all as specified and as directed by Engr-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cms thick with soils in soft/loose soil complete all as specified and as directed by Engr-in-charge.

Removing excavated material exc 250m but not exc 500m and depositing where directed complete all as specified and as directed by Engr-in-charge.

Material and labour for PCC type D2 ,1:4:8 (Using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed by Engr-in-charge.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and as directed by Engr-in-charge.

Material and labour for RCC (nominal mix) type A-1 1:1.5:3 (Using 20mm graded stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for coloumns, etc., basement slabs, under-reamed piles and mass concrete complete all as specified and as directed by Engr-in-charge.

Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete, square, rectangular or polygonal complete all as specified and as directed by Engr-in-charge.

Material and labour for RCC (nominal mix) type A-1 1:1.5:3 (Using 20mm graded stone aggregate) in columns, pillars, piers, posts and struts complete all as specified and as directed by Engr-in-charge.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels beam, tie beam, cantilevers, shelves including supports, overhangs, etc., also splays between floors and rough finished, complete all as specified and as directed by Engr-in-charge.

Material and labour for RCC (nominal mix) type A-1 1:1.5:3 (Using 20mm graded stone aggregate) in beams, cantilevers, bressummers, tie beam, lintels over 1.5m span complete all as specified and as directed by Engr-in-charge.

Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exc 200mm thick (horizontal or sloping) complete all as specified and as directed by Engr-in-charge.

Material and labour for RCC (nominal mix) type A-1 1:1.5:3 (Using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engr-in-charge.

Material and labour for TMT bars 10mm dia and over, cut to length, bent to shape required, inculding cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engr-in-charge.

All as per item No.14 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

Material and labour for hardcore of gauge not exc 63mm of broken stone, deposited, spread and leveled in layers not exc 15 cms thick, watered and rammed to a true surface complete all as specified and as directed by Engr-in-charge.

Material and labour for 75mm thick PCC 1:2:4 type B-1 (Using 20mm graded stone aggregate) including finishing the surface even and fair complete all as specified and as directed by Engr-in-charge.

Material and labour for precast cement concrete block masonry with solid blocks type C1, 1:3:6 (Using 20mm graded stone aggregate) exc 10 cms in width and setting in cement mortar 1:6 complete all as specified and as directed by Engr-in-charge.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement including mixing of water proofing compound wherever required as per manufacturers instructions complete all as specified and as directed by Engr-in-charge. Note: WPC shall be measured and paid separately.

Material and labour for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge.

Material and labour for rendering 10mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling of chajja, roof projection, shelves etc., and finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge.

Supply only liquid water proofing compound complete all as specified and as directed by Engr-in-charge.

Material and labour for virified ceramic tiles 10mm thick (square/ rectangular) polished, area of each tiles not exc 0.36 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:6 complete all as specified and as directed by Engr-in-charge.

All as per item No.23 here-in-before but as in skirting over and including 10mm thick rendering on brick work or concrete surface wall as backing coat of cement mortar 1:4.

Material and labour for 10mm thick plaster of paris ceiling (gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (fillets, metal frame work and G.I. wire mesh paid separately) including cost of two or more coats to given even shade of plastic emulsion paint on ceiling with putty work with designer ceiling (with part plylaminate and cover) complete all as specified and as directed by Engr-in-charge.

Material and labour for Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with Gl cleats and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flanges of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and as directed by Engr-in-charge.

Supply and fix for hangers 6mm dia G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and as directed by Engr-in-charge.

Material and labour for two coats of distempering on wall with distemper oil emulsion white or tinted over primer over a coat of 3mm thick wall care putty, including preparation of new surfaces complete all as specified and as directed by Engr-in-charge.

Supply and fix for mild steel tubular trussed, purlins, fencing posts, crane gantries rails and fastenings including special shaped washer etc., complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 including distance pieces, cleats, nuts and bolts any size and length etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for mild steel plates (plain or chequered) Fe-410-W (Gde-E-250) quality B channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed by Engr-in-charge.

Supply and fix for mild steel screw bolts diameter of neck in 12mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nuts, exc 5cm not exc 10cm long complete all as specified and as directed by Engr-in-charge.

Supply and fix for mild steel flats 40x6mm thick for hand rails, wind ties, posts and struts in fencing screwed or welded to shape as directed, including all necessary drilling, bolting or riveting etc., and similar work confirming to Fe 410-O or Fe 310-O complete all as specified and as directed by Engr-in-charge.

Supply and fix for prepainted galvalume aluminium zinc coating GI based corrugated steel sheeting 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws/ J hooks and bolts as required complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxied priming complete all as specified and as directed by Engr-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engr-in-charge.

Material and labour for 25mm thick PCC 1:2:4, type B0 (Using 12.5mm graded stone aggregate) as in flooring complete all as specified and as directed by Engr-in-charge.

Material and labour for coloured non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm, in floors etc., set and jointed in neat cement slurry over and including 15mm thick screed bed of cement mortar 1:6 and pointed with white or coloured cement to match complete all as specified and as directed by Engr-in-charge.

Material and labour for coloured glazed ceramic design tiles 350x250x7mm/ 450x300x7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed by Engr-in-charge.

Supply and fix for UPVC 20mm dia pipe pressure rating 10 Kgf/cm2 with all fittings and fixed to wall /laid in floor complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs premium quality 15mm bib tap with wall flange chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs soap dish Make-Jaguar Code No- CAN-1137/AKP-35731P or techno commercially equivalent from CERA/ HINDWARE / PRAYAG etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs toilet paper roll holder with flap Make-Jaguar Code No- AKP-35753P or techno commercially equivalent from CERA/ HINDWARE / PRAYAG etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs single lever basin mixture with popup waste system with 450mm long braided hoses Make: Jaquar-LYR-38051B/ORP-10011BPM or techno commercially equivalent from CERA/ HINDWARE / PRAYAG etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs table top basin of size 170x835x455mm/ 565x425x140mm of white colour of make-Jaquar Cat No-KUS-WHT 35935/ JDS-WHT-0547 or techno commercially equivalent from CERA/ HINDWARE / PRAYAG etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 15mm bore hand shower (health faucet) with 8mm dia, 1m long flexible tube and wall hook of Jaguar Cat No- ALD -573/ALD 577 or techno commercially equivalent from CERA/ HINDWARE / PRAYAG etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs towel rail of 600mm long of Make-Jaguar Cat no-AHS-1507 or techno commercially equivalent from CERA/ HINDWARE / PRAYAG etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs glass shelf of 600mm long with CP brackets Make-Jaguar Cat no-CAN-1171N or techno commercially equivalent from CERA/ HINDWARE / PRAYAG etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for rimless single piece-WC with UF slim seat cover, hinges fixing accessories and accessories set, cistern fittings, size 380x670x765mm with hydraulic sheet cover and connecting to 'S' trap 300mm of Make Jaguar FSS-WHT-29853S300UFSM / OPS-WHT-0205. including taking down old one complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs CP connection 15mm dia and 450mm long with two Nos of brass checknuts and washers complete all as specified and as directed by Engr-in-charge.

Supply and fix for stainless steel gratings size 125mm dia complete all as specified and as directed by Engr-in-charge.

Supply and fix for towel rack without lower hanger of 600mm long and 3 Nos hooks Make-Jaguar Code No- AHS-1581 or techno commercially equivalent from CERA/ HINDWARE / PRAYAG etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for towel ring square with round flange Make-Jaguar Code No-ACN-CHR-7721 or techno commercially equivalent from CERA/ HINDWARE / PRAYAG etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs angle stop cock with wall flange 15mm dia chromium plated, screwed down, high pressure, screwed both ends for 15mm bore iron pipes or for unions of Make-Jaguar Cat no-CON 059KN or techno commercially equivalent from CERA/ HINDWARE / PRAYAG etc. complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs fancy type CP 2 way bib cock with wall flanges complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 32mm dia waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flanged end bedded in red lead cement and other end fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix for 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or fixed with floor including necessary fixing cleats/ clamps complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed with wall including necessary fixing cleats/ clamps complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs PVC bends of 110mm dia complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs PVC bends of 75mm dia complete all as specified and as directed by Engr-in-charge.

Supply and fix for rotational moulded polyethylene water storage tanks of white colour triple layered (ISO certified) (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 litres, including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and as directed by Engr-in-charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons including granite slab in kitchen platform laid, bedded and pointed in any mortar etc., complete all as specified and as directed by Engr-in-charge.

Material and labour for 20mm thick granite of any type work (table rubbed and polished) in cooking platform, window cills, steps, wall lining and like in cement mortar 1:4 including pointing in white cement mortar 1:2 using marble dust with admixture of pigment to match with shade granite including 15mm thick in CM 1:6 complete all as specified and as directed by Engr-in-charge.

Material and labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed by Engr-in-charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) wooden not exc 1.5 sqm each complete all as specified and as directed by Engr-in-charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) wooden exc 1.5 sqm not exc 4 sqm each complete all as specified and as directed by Engr-in-charge.

Supply and fix for 100mm long stainless steel butt hinges complete all as specified and as directed by Engr-in-charge.

Supply and fix for 125mm stainless steel barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix for 125mm stainless steel handles complete all as specified and as directed by Engr-in-charge.

Supply and fix for 150mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix for second class hard wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed by Engr-in-charge.

Supply and fix for 35mm thick 2nd class hardwood factory made plain, framed, panelled shutters (any number of panels) factory made with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed by Engr-in-charge.

Supply and fix for 35mm thick 2nd class hard wood glazed and skeleton shutter as in door open rebated and prepared to receive glass, gauge etc., (without sash bars) edges of framing plain, chambered or rounded mitred and beads for securing glass etc., size of members of shutter as specified in SSR part-I, Sec-08, clause 8.24(a), kiln seasoned and chemically pressure treated complete all as specified and as directed by Engr-in-charge.

Material and labour for 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of untreated new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and as directed by Engr-in-charge.

Supply and fix for powder coated anodised aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs powder coated anodised aluminium door, window and ventilator shutters (minimum thickness of powder coating 50 microns), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix in repairs sheet glass of 4.8mm thick ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified and as directed by Engr-in-charge.

Supply and fix for 19mm thick plywood 7 ply with BWR type BB, fixed with adhesive and screws for top, bottom and sides of working table/ shelves/ wall mounted shelves of any shape to required size, pattern/ design, including necessary fixing to wall with necessary fixing bolts and accessories for wall mounting and floor bush for work stations complete all as specified and as directed by Engr-in-charge.

Supply and fix for 12mm thick plywood 7 ply with BWR type BB, fixed with adhesive and screws as in shutters and partitions of working tables/ shelves/ wall mounted shelves, trolley mounted racks complete all as specified and as directed by Engr-in-charge.

Material and labour for 0.90mm thick decorative laminate type I of surface finish (colour and pattern as approved) fixed with approved adhesive as per manufacturers instruction finished to approved size for working tables/ shelves/ wall mounted shelves of any shape of any pattern and design etc., complete all as specified and as directed by Engr-in-charge.

Supply and fix for mild steel nickel coated telescopic drawer slider with ball bearing, one inch size, 18 inch long two beam max load capacity 35-40 kg suitable for working table, drawer and size and any pattern complete all as specified and as directed by Engr-in-charge.

Supply and fix for cast brass powder coated automatic lock and release butt hinges of size 100mm complete all as specified and as directed by Engr-in-charge.

Supply and fix for cast brass powder coated box type decorative door handle of size 75mm complete all as specified and as directed by Engr-in-charge.

Supply and fix for 32mm drawer/ cupboard lock and key of make-Godrej model-"Curvo" or techno commercially equivalent from Link etc complete all as specified and as directed by Engr-in-charge.

Supply and fix for 50mm dia PVC cable manger suitable for working table/ conference table of any pattern complete all as specified and as directed by Engr-in-charge.

Supply and fix for internal auto closing concealed hinge complete all as specified and as directed by Engr-in-charge.

Supply and fix for 6 inches premium quality chrome finish handle complete all as specified and as directed by Engr-in-charge.

Supply and fix for good quality telescopic channel set for drawer multitech high capacity 500mm long complete all as specified and as directed by Engr-in-charge.

Supply and fix for 19-20mm wide and 0.80mm thick decorative type PVC beading complete all as specified and as directed by Engr-in-charge.

Supply and fix for cutlary drawer of length-420mm, depth-485mm, height-100mm made of stainless steel of grade IS:202 complete all as specified and as directed by Engr-in-charge.

Supply and fix for plain basket drawer of length-420mm, depth-485mm, height-100mm made of stainless steel of grade IS:202 complete all as specified and as directed by Engr-in-charge.

Supply and fix for thali basket drawer of length-420mm, depth-485mm, height-150mm made of stainless steel of grade IS:202 complete all as specified and as directed by Engr-in-charge.

Material and labour for hardcore of gauge not exc 63mm of broken stone, deposited, spread and leveled in layers not exc 15 cms thick, watered and rammed to a true surface complete all as specified and as directed by Engr-in-charge.

Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design and pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness and size/ shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed by Engr-in-charge.

Material and labour for 50mm thick cement concrete type B1, 1:2:4 (Using 40mm graded stone aggregate) as in flooring, foot path, hard standing, plinth protection, bases of water tanks etc,. complete all as specified and as directed by Engr-in-charge.

Material and labour for 75mm thick PCC 1:2:4 type B1 (Using 20mm graded stone aggregate) including finishing the surface even and fair complete all as specified and as directed by Engr-in-charge.

Material and labour for coloured designed chequered cement concrete tiles of a size 300x300x25mm thick with white cement and pigment in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 20mm thick screed bed of cement mortar 1:6 complete all as specified and as directed by Engr-in-charge.

Material and labour for sand filling under floors or in foundation including watering and consolidation complete all as specified and as directed by Engr-in-charge. Note: Only punned thickness shall be measured for payment.

Material and labour for 75mm thick PCC 1:4:8 type D-2 (Using 40mm graded stone aggregate) for hard standing including finishing the surface even and fair complete all as specified and as directed by Engr-in-charge.

Material and labour for 100mm thick PCC 1:2:4 type B-1 (Using 20mm graded stone aggregate) for floor including finishing the surface even and smooth with using extra cement complete all as specified and as directed by Engr-in-charge.

Material and labour for 2 coats of distempering wall with distemper oil emulsion white or tinted through mechnical means over a coat of 1mm thick wall care putty, including preparation of old surface after complete removal of existing treatment complete all as specified and as directed by Engr-in-charge.

Material and labour for complete removal of existing treatment of walls and applying two coats of exterior emulsion paint (weather coat) through mechnical means over a coat of approved primer complete all as specified and as directed by Engr-in-charge.

Material and labour for complete removal of existing treatment preparation of old painted surface of any description not otherwise described wood and wood based surfaces over 10 cm width of girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of old decorated surface of ceiling including washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of distemper oil emulsion through mechnical means on ceiling complete all as specified and as directed by Engr-in-charge.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engr-in-charge.

Material and labour for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge.

Material and labour for 40mm thick PCC 1:2:4, type B-0 (Using 12.5mm graded stone aggregate) as in flooring, finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge.

Material and labour for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 20 mm thick screed bed in CM 1:4 on floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engr-in-charge.

Supply and fix for Tee grid suspension system of size 600x600mm type-1 made out of rolled framed hot dipped galvanised steel zinc coated of not less than 120 gm/sqm, main runner shall be 0.3mm thick of section 24x33mm cross runner 0.3mm thick of section 24x25mm, wall angle shall be 0.63mm thick of section 24x24mm grid shall be suspended by 4mm dia adjustable quick fit hanger rod, system exposed portion shall be prepainted polyster coated in off white /white in colour with material, fixing, jointing etc., all as per manufactures instructions complete all as specified and as directed by Engr-in-charge.

Supply and fix for 5.5mm thick ceiling board with powder coated GI suspended ceiling with 9mm wide T section. The frame work comprises of main runner at 1200mm c/c. The last hanger at end of each main runner should not be greater than 450mm from wall. T channel 1200mm long cross was to be inter locked between main work at 600mm long cross to centrally between the 1200mm cross tees main T channel suspended with 6mm dia GI (upto 1200m length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flash 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long with following specifications complete all as specified and as directed by Engr-in-charge. (i) Ceiling board dimension 595x595mm (ii) Weight - 5.94 kg/m2 (iii) Density - 1200 kg/m3 (iv) Accoustics - 34 DB (v) Moisture resistance - Yes (vi) Fire resistance - Yes (vii) Thermal insulation - Yes

Supply and fix for 35mm thick 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and as directed by Engr-in-charge.

Material and labour for preparation of untreated new wooden surface of any description not exc 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and as directed by Engr-in-charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and as directed by Engr-in-charge. Note: All the debris/ demolished material shall be removed from site to outside AF campus at contractors risk and cost in accordance with all applicable federal state and local regulations as and when directed by Engr-in-charge.

Material and labour for virified ceramic tiles 10mm thick jointless (square/ rectangular) polished, area of each tiles not exc 0.36 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match set and jointed in neat cement slurry over and including 15mm thick screed bed of CM 1:6 and pointed in white/ coloured cement to match complete all as specified and as directed by Engr-in-charge.

All as per item No.117 here-in-before but as in wall skirting over and including 10mm thick rendering of CM 1:4.

Material and labour for glazed ceramic coloured/ digital tiles in vertical surface 300x450x7mm/ 300x600x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick bedding layer of cement mortar 1:4 complete all as specified and as directed by Engr-in-charge.

Supply and fix for powder coated (minimum thickness of powder coating 50 microns) anodised aluminium window and ventilator shutters, sliding /side hung type without sash bars, aluminium sections weighing not less then 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21, 100mm long (2 Nos) suitable handle (1 No) complete all as specified and as directed by Engr-in-charge. Note: sheet glass and SS wiremesh shall be measured and paid separately.

Supply and fix for 5.50mm thick sheet glass ordinary quality and glazing with EPDM rubber/ neoprene gasket etc., exc 0.50 sqm in each panes complete all as specified and as directed by Engr-in-charge.

Supply and fix for 125mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed by Engr-in-charge.

Supply and fix for 200mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engr-in-charge.

Supply and fix for 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and as directed by Engr-in-charge.

Supply and fix for 150mm aluminium handles, cast type anodised complete all as specified and as directed by Engr-in-charge.

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fittings supply and fix for fixtures such as switches, sockets, ceiling rose, pendants, regulators, light fittings etc., removing materials to store for keeping in safe custody for taking credit and making good to disturbed surfaces/ wall with plaster and matching with the existing colour of wall /floor etc., complete all as specified and as directed by Engr-in-charge.

Taking down carefully ceiling fan from ceiling, painting of ceiling fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc., and refixing of ceiling fan in same position in serviceable condition including provision of three core 1.5 sqmm copper cable from ceiling rose to fan connector complete all as specified and as directed by Engr-in-charge.

Taking down carefully any size/ any sweep exhaust fan from wall, cleaning all dust, oil etc., and refixing of exhaust fan in same position in serviceable condition including nuts, bolts, washer including provision of three core 1.5 sqmm copper cable from ceiling rose to exhaust fan complete all as specified and as directed by Engr-in-charge.

Taking down carefully geyser of capacity 50 /25 ltrs from wall, painting of geyser complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc., and refixing the geyser of capacity 50/ 25 ltrs after repair in new position including drilling holes in any type wall fixing four nos anchor bolts five inch size, nuts and washer and connected to water pipe line with two nos hot and cold 600mm long connection pipe and electric connection and testing complete all as specified and as directed by Engr-in-charge.

Material and labour for concealed point wiring with 1.5 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable in and including PVC rigid concealed conduit medium grade of size not less than 25mm dia ISI marked with all accessories such as tee, bend, joint cover etc., round/ square PVC blocks at junction for batten holders, ceiling rose etc., screws, gutti/ roul plugs PVC as per site requirements including fixing inside stone walls /brick masonary walls or any type wall /ceilings /floors etc., anodized modular MS sunken boxes made out of MS sheet of thickness not less than 1.6mm with earth dolly for mounting of modular switches/ sockets/regulator etc., and 1.5 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable as continuous earth lead connected to common earth dolly and colour coding of cables such as Phase - Red, Neutral-Black, and Earth-Green and making good to disturbed surfaces/ wall with plaster and matching with the existing colour of wall /floor etc., complete all as specified and as directed by Engr-in-charge for the following :- Note: Cutting, chasing, drilling in any type of wall for fixing of concealed conduit and modular sunken boxes included in quoted rate. No extra payment will be made for this.

One light point controlled by one single pole 5 Amps switch.

One ceiling fan/ wall fan point controlled by one single pole 5 Amps switch.

One exhaust fan point controlled by one single pole 5 Amps switch.

One 5 pin socket point 5 Amps on independent board.

One 5 pin socket point 5 Amps on same board with other switches.

One bell/ buzzer point controlled by one push button 5 Amps switch on independent board.

Four light controlled by one single pole 5 Amps switch.

Six light point controlled by one single pole 5 Amps switch.

Material and labour for concealed point wiring with 2.5 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable in and including PVC rigid concealed conduit medium grade of size not less than 25mm dia ISI marked with all accessories such as tee, bend, joint cover etc., round/ square PVC blocks at junction for batten holders, ceiling rose etc., screws, gutti/ roul plugs PVC as per site requirements including fixing inside stone walls/ brick masonary walls or any type wall /ceilings /floors etc., anodized modular MS sunken boxes made out of MS sheet of thickness not less than 1.6mm with earth dolly for mounting of modular switches/ sockets/regulator etc., and 2.5 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable as continuous earth lead connected to common earth dolly and colour coding of cables such as Phase - Red, Neutral-Black, and Earth-Green and making good to disturbed surfaces/ wall with plaster and matching with the existing colour of wall /floor etc., for one 15 Amps switch socket combination on independent board complete all as specified and as directed by Engr-in-charge. Note: Cutting, chasing, drilling in any type of wall for fixing of concealed conduit and sunken boxes included in quoted rate. No extra payment will be made for this.

Material and labour for concealed point wiring with 4 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable in and including PVC rigid concealed conduit medium grade of size not less than 25mm dia ISI marked with all accessories such as tee, bend, joint cover etc., round/ square PVC blocks at junction for batten holders, ceiling rose etc., screws, gutti/ roul plugs PVC as per site requirements including fixing inside stone walls/ brick masonary walls or any type wall /ceilings /floors etc., anodized modular MS sunken boxes made out of MS sheet of thickness not less than 1.6mm with earth dolly for mounting of modular switches/ sockets/regulator etc., and 4 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable as continuous earth lead connected to common earth dolly and colour coding of cables such as Phase - Red, Neutral-Black, and Earth-Green and making good to disturbed surfaces/ wall with plaster and matching with the existing colour of wall /floor etc., for one 15 Amps switch socket combination on independent board complete all as specified and as directed by Engr-in-charge. Note: Cutting, chasing, drilling in any type of wall for fixing of concealed conduit and sunken boxes included in quoted rate. No extra payment will be made for this.

Supply and fix for modular switch, 1 Module single pole one way 10 Amps complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular socket, 2 Module, 6 Amps, 5 pin, 240 volts AC complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular switch, 1 Module single pole one way 16 Amps complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular socket, 2 Module, 6/16 Amps, 6 pin, 240 volts AC complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular type fan regulator 2 module upto 120 watts with 5 step speed control for fans any sweep 1200mm/ 1400mm complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular type bell push 6 A, 1 Module complete all as specified and as directed by Engr-in-charge.

Supply and fix for ding dong bell, AC, 230 volts, single pole complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular white cover plate with frame, 2 module complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular white cover plate with frame, 3 module complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular white cover plate with frame, 4module complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular white cover plate with frame, 6 module complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular white cover plate with frame, 8 module complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular metal flush box 1/2 module complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular metal flush box 3 module complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular metal flush box 4 module complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular metal flush box 6 module complete all as specified and as directed by Engr-in-charge.

Supply and fix for modular metal flush box 8 module complete all as specified and as directed by Engr-in-charge.

Supply and fix for PVC ceiling rose 65x50mm surface type with 3 terminals complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED light fitting, 4 feet 1x20 Watts, 220 volts, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED mirror light fitting 2 feet, 10 Watts, 220 volts, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED fitting of size 600x600mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor wire of suitable size complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED light fitting round shape 15 watts white /warm white as per requirement 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engr-in-charge.

Supply and fix for decorative wall light, 9 watt stainless steel, rust free fixture with white glass diffuse with LED lamp complete all as specified and as directed by Engr-in-charge.

Supply and fix for flexible LED strip light of warm white colour with IP 65 20 watt /Mtr including driver, adaptor and all accessories as per site requirement complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED light fitting 9 /10 Watts bulk head luminaires including LED light driver holder connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by Engr-in-charge.

Supply and fix for LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including brackets made out of 50mm dia light grade GI pipe 1.50m long bent to shape and size as per site requirement for fixing of street light fitting on poles/ walls including flat iron clamps-02 Nos of size 30x5mm made to shape including nuts, bolts and washers complete all as specified and as directed by Engr-in-charge.

Supply and fix for electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litres, BEE 5 star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece complete all as specified and as directed by Engr-in-charge.

Supply and fix for electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 50 litres, BEE 5 star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece complete all as specified and as directed by Engr-in-charge.

Supply and fix for ceiling fans complete with blades, down rods, electronic regulator and accessories, AC single phase 230 V, 1200mm sweep. Minimum air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed by Engr-in-charge.

Supply and fix for exhaust fan steel body AC single phase 230 V of size 380mm sweep, 900 RPM with blades, and frame and louvers complete all as specified and as directed by Engr-in-charge.

Supply and fix for wall mounted fan AC single phase 230 Volt of size 400mm sweep in stone/ brick masonary or any type wall with four inch screws, gatti /PVC roul plugs as per site requirement including making good to disturbed surfaces/ wall with plaster and matching with the existing colour of wall /floor complete all as specified and as directed by Engr-in-charge.

Material and labour for concealed sub main wiring with two single core 2.5 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable in and including heavy grade PVC rigid concealed conduit medium grade of size not less than 25mm dia ISI marked with all accessories such as tee, bend, joint cover etc., screws, gutti /roul plugs PVC as per site requirements including fixing inside stone walls/ brick masonary walls/ceilings/floors etc., with 2.5 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable as a continuous earth wire and connected to common earth dolly and colour coding of cables such as Phase - Red, Neutral-Black, and Earth-Green and making good to disturbed surfaces/ wall with plaster and matching with the existing colour of wall /floor etc., complete all as specified and as directed by Engr-in-charge. Notes: (i) Two run of single core 2.5 sqmm cable and one run 2.5 sqmm earth wire including PVC concealed conduit together will be measured as one unit. (ii) Cutting, chasing, drilling in any type of wall for fixing of concealed conduit for sub main wiring included in quoted rate. No extra payment will be made for this.

Material and labour for concealed sub main wiring with two single core 4 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable in and including heavy grade PVC rigid concealed conduit medium grade of size not less than 25mm dia ISI marked with all accessories such as tee, bend, joint cover etc., screws, gutti /roul plugs PVC as per site requirements including fixing inside stone walls/ brick masonary walls/ceilings/floors etc., with 4 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable as a continuous earth wire and connected to common earth dolly and colour coding of cables such as Phase - Red, Neutral-Black, and Earth-Green and making good to disturbed surfaces/ wall with plaster and matching with the existing colour of wall /floor etc., complete all as specified and as directed by Engr-in-charge. Notes: (i) Two run of single core 4 sqmm cable and one run 4 sqmm earth wire including PVC concealed conduit together will be measured as one unit. (ii) Cutting, chasing, drilling in any type of wall for fixing of concealed conduit for sub main wiring included in quoted rate. No extra payment will be made for this.

Material and labour for concealed sub main wiring with two single core 6 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable in and including heavy grade PVC rigid concealed conduit medium grade of size not less than 25mm dia ISI marked with all accessories such as tee, bend, joint cover etc., screws, gutti /roul plugs PVC as per site requirements including fixing inside stone walls/ brick masonary walls/ceilings/floors etc., with 6 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable as a continuous earth wire and connected to common earth dolly and colour coding of cables such as Phase - Red, Neutral-Black, and Earth-Green and making good to disturbed surfaces/ wall with plaster and matching with the existing colour of wall /floor etc., complete all as specified and as directed by Engr-in-charge. Notes: (i) Two run of single core 6 sqmm cable and one run 6 sqmm earth wire including PVC concealed conduit together will be measured as one unit. (ii) Cutting, chasing, drilling in any type of wall for fixing of concealed conduit for sub main wiring included in quoted rate. No extra payment will be made for this.

Material and labour for earthing complete with galvanised steel earth electrode plate of size 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below normal ground level, connected to galvanised iron wire 4mm dia as earth lead up to test point with suitable size GI nuts /bolts, washers, check nut and brazed properly upto main board, LT panel etc., and adequate quantity of charcoal and salt 15 cm around the earth plate including earth pit in cement concrete 1:2:4 type B-1 (Using 20mm graded stone aggregates) 40mm thick precast RCC cover in 1:2:4 reinforced with 8mm dia TMT bars 3 Nos both way including CI cover 10mm thick with hinged and frame of angle iron 25x25x6mm with 6mm dia MS bar handle made to shape, excavation and earth work in any type of soil and including medium grade GI watering pipe 20mm bore with funnel and wire mesh and medium grade GI protection pipe 15mm bore up to main board complete all as shown in electrical plate No.3 of MES schedule Part-I, connected to earthing testing point and testing on completion complete all as specified and as directed by Engr-in-charge. Notes: (i) The unit rate includes 15mm dia GI pipe upto 7.5m for protection of earth lead. (ii) The unit rate includes galvanised iron wire 4mm dia from earth electrode to test point upto 7.5m. (iii) In case measured value of earth resistance of each earthing is recorded more than 3 ohms then the earthing shall be re-done by the contractor without any extra cost to the department. (Item 42 of Job a + item 24 of Job b (E&M) = 2+2 =4)

Supply and fix for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit /pipe or fixed to poles or any other indicated situation for loop earthing 4mm dia galvanised iron or steel wire complete all as specified and as directed by Engr-in-charge.

Supply and fix for sheet metal enclosure for DB's double door TPN 04 ways when MCCB 125 Amps to be used as incomer and outgoing as MCB single pole with 200 Amps rated copper bus bar 415 V complete all as specified and as directed by Engr-in-charge.

Supply and fix for MCCB, 4 poles 415 Volts, 125 Amps, 16 kA, 50 Hz, AC, fixed thermal and fixed magnetic type with suitable size lugs and testing complete all as specified and as directed by Engr-in-charge.

Supply and fix for sheet metal enclosure for DB's double door SPN, 12 ways when MCBs to be used single pole and neutral, deep drawn with 200 Amps rated copper bus bar 230 Volt complete all as specified and as directed by Engr-in-charge.

Supply and fix for testing and commissioning MCB SPN, 40 to 63 Amps, 230 V, C-series with breaking capacity of 10 KA complete all as specified and as directed by Engr-in-charge.

Supply and fix for testing and commissioning MCB SP, 6-32 Amps, 230 V, C-series with breaking capacity of 10 KA complete all as specified and as directed by Engr-in-charge.

Supply and fix for single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB of rating 32 Amps complete all as specified and as directed by Engr-in-charge.

Material and labour for point wiring with 1.5 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable in and including heavy grade PVC casing and capping ISI marked broken white or of cream colour with all accessories such as tee, bend, joint cover etc., round/ square PVC blocks at junction for batten holders, ceiling rose etc., screws, gutti/ roul plugs PVC all as per site requirements including fixing on stone walls/ brick masonary walls/ ceilings /floors etc., modular MS sunken boxes with earth dolly for mounting of modular switches /sockets /regulator etc., and 1.5 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable as continuous earth lead connected to common earth dolly and colour coding of cables such as Phase - Red, Neutral-Black, and Earth-Green and making good to disturbed surfaces/ wall with plaster and matching with the existing colour of wall /floor etc., complete all as specified and as directed by Engr-in-charge for the following:-

One light point controlled by one single pole 5 Amps switch.

One ceiling fan point controlled by one single pole 5 Amps switch.

One exhaust fan point controlled by one single pole 5 Amps switch.

One 5 pin socket point 5 Amps on independent board.

One 5 pin socket point 5 Amps on same board with other switches.

All as per item No.175 here-in-before but for power point wiring with 2.5 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volt grade cable and 2.5 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volt grade cable as continuous earth lead for 6 pin 15 Amp modular switch socket outlet on independent board complete all as specified and as directed by Engr-in-charge.

Supply and fix for sheet metal enclosure for DB's double door SPN, 8 ways when MCBs to be used single pole and neutral, deep drawn with 200 Amps rated copper bus bar 230 Volt complete all as specified and as directed by Engr-in-charge.

Supply and fix for testing and commissioning MCB SPN, 40 Amps, 230 V, C-series with breaking capacity of 10 KA complete all as specified and as directed by Engr-in-charge.

Taking down carefully ceiling fan from ceiling, painting of ceiling fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc., and refixing of ceiling fan in same position in serviceable condition including provision of four feet down rod with fixing arrangement including provision of three core flexible 1.5 sqmm copper cable from ceiling rose to fan connector complete all as specified and as directed by Engr-in-charge.

Material and labour for sub main wiring with two single core 4 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable in and including heavy grade PVC casing and capping ISI marked broken white or of cream colour with all accessories such as tee, bend, joint cover etc., screws, gutti/ roul plugs PVC all as per site requirements including fixing on surface on stone walls /brick masonary walls/ceilings/floors etc., with 4 sqmm PVC insulated, unsheathed, FRLS multistranded copper conductor 1100 volts grade cable as a continuous earth wire and connected to common earth dolly complete and making good to disturbed surfaces/ wall with plaster and matching with the existing colour of wall /floor etc., and colour coding of cables such as Phase - Red, Neutral-Black, and Earth-Green complete all as specified and as directed by Engr-in-charge. Note: Two run of 4 sqmm single core cable and one run 4 sqmm earth wire including PVC casing and capping together will be measured as one unit.

EURO ENTERPRISES (BID ID -3413726)

chowdeshwariconstructionco (BID ID -3413752)

raashi constructions (BID ID -3413791)