BARCT/NRB/GSO/EMC/CMT/178

Amount

Dismantling brick work in Cement mortar carefully without damaging adjacent structures including stacking of materials and dispoal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Dismantling old plaster / skirting carefully , raking out joints and cleaning the surface for plaster including scaffolding disposal of rubbish to the dumping ground within 100 m lead

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 25 mm and up to 40 mm

Dismantling doors, windows and clear storey openings (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows) Of area 3.00 Sq.M and below and as directed by engineer.

Dismantling G.I pipes of all diameter external work including excavation and refilling trenches after taking out pipes manually / by mechanical means including stacking of pipes within 100 m lead as per direction of Engineer-in-charge

Dismantling plain cement concrete manually / by mechanical means carefully without damaging adjacent structures including disposal of debris within 2000 m lead as per direction of Engineer-incharge

Dismantling flushing cistern of any size including stacking of useful materials near the site and disposal of unserviceable materials within 100 m lead and as directed by engineer-in-charge

Dismentaling of indian WC pan /european wc pan of any size including stacking of unused material near to site and disposal within 1000m lead and as directed by enginner-Incharge

Dismentaling of indian wash basine of any size including stacking of unused material near to site and disposal within 1000m lead and as directed by enginner-Incharge

Provding and constructing brick work in Cement mortar using standard bricks of approved class/ quality, make or brand in foundation and plinth including curing, raking out joints, simultaneous pointing below plinth level if specified, complete as per drawings, specifications and as directed by the Engineer-incharge Brick work in C.M 1:6 using crushed sand.

Providing and constructing Half brick masonry using bricks of approved quality / class, brand/ make in partition walls in C.M 1:4 (using crushed sand) including scaffolding, raking out joints, curing etc. complete and with stiffners of RCC 1:2:4 (105 X 75 mm size) at every 900 mm height including form work curing etc. complete as per specifications and as directed by the Engineer-incharge but excluding reinforcement up to plinth level and as directed by engineer. (Reinforcement will be paid under relevant item)

Providing 12 mm thick Internal plastering in cement mortar 1:4 without cement punning (using crushed sand) finished smooth, including sieving of sand to required fineness,preparation of the surface, scaffolding, curing all as per specifications, drawings and as directed at site complete

Providing and fixing minimum 17 mm thick gang saw cut mirror polished marble (premoulded and prepolished) machine cut marble for , window sills, facias , door frame and similar locations of required size, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edge to give high gloss finish etc. complete as directed by the Engineer-incharge at all levels

Providing and fixing minimum 17 mm thick gang saw cut mirror polished granite (premoulded and prepolished) machine cut ZEBRA BLACK colour granite for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edge to give high gloss finish etc. complete as directed by the Engineer-incharge at all levels

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.. Concealed work, including cutting chases and making good the walls etc.15 mm dia pipe

20 mm dia pipe

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm dia pipe

20 mm dia pipe

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS 15622 of approved make. shade and colour of size ranging from 300 - 600 mm long and 300 mm - 600 mm wide and thickness not less than 6 mm as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour Tile grout of approved make of matching shade including using PVC tile trim in the exposed corners, complete as per drawings, patterns and specifications complete as directed by the Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed anti skid floor tiles of minimum 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm conforming to IS 15622 of approved make in all colours and shades as approved by Engineer-in-charge over a bed of 20 mm thick bed of cement mortar 1:4 (using crushed sand) and jointing with grey cement slurry including pointing with white cement based Tile grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Enginner-in-charge

Providing and fixing using tiles of size 600 x 600 mmGlazed VITRIFIED floor tiles of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 10 mm thick bed of polymer mortar (Adhesive)and jointing with grey cement including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge

Providing and Fixing CP brass 100 mm dia shower rose with Shower arm of approved make as per specifications and as directed by Engineer-in-charge complete

Providing and fixing 100 mm dia S.S. jali of approved make or as directed by engineer in charge

Providing and fixing C.P brass bib cock of heavy quality of specified / approved make as per specifications and as directed by the Engineer-in-charge 15 mm dia bib cock of approved type and make .

Providing and fixing C.P brass concealed stop cock of Heavy Quality of specified / approved make as per specifications and as directed by the Engineer-in-charge 15 mm n.b CP brass concealed stop cock of approved make

Providing and fixing PVC inlet connection pipes heavy quality suitable for hot and cold including CP brasss unions and nuts 15mm dia 600 mm long

Supply and fixing heavy quality hot and cold, three in one tap mixture value includng cost of material and labour charge approved MAKE by Engineer-in-Charge

Providing and fixing cast iron nahani trap / floor trap of 100 mm inlet and 75 mm outlet, (weighing 5.80 Kg each), jointing with lead with the connection pipes, placing as per the drawings, embedding in cement concrete 1:2: 4 and making circular hole up to floor level using 110 mm O/D PVC pipes of 6 Kg / sq.cm pressure and fixing 1 No 125 mm dia C. P brass grating , complete all as specifications and drawings and as directed by the Engineer-in-charge

Providing and fixing Indian water closet (Orissa pan) of approved make with 100 mm China ware P or S trap, One no. 10 litre High level or low level white PVC flushing cistern with flush pipe & bend with manually controlled device (handle lever) conforming to IS:7231, PVC 15 mm Inlet connection with all fittings and fixtures complete including all connection, embedding in position commissioning, cleaning etc. all as per drawings and specifications and as directed by the Engineer-in-charge. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china European type Water Closet with 'P' or 'S' Trap with solid seat and lid of approved make, 10 litre low level white PVC flushing cistern with manually controlled device (handle lever) conforming to IS:7231, flush bend, fixing EWC with C.P brass screws, 15 mm PVC heavy quality inlet connection of 450 mm long, including testing , commissioning & cleaning etc. complete all as per drawings and specifications and as directed by the Engineer-in-charge E.W.C. pan in White colour with ISI marked white solid plastic seat and lid.

Providing and fixing vitreous China wash basin of approved make and colour with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm long PVC Inlet connection, 32 mm heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge White vitreous China wash basin size 550 x 400 mm/ 550 x 420 mm and equivalent sizes with single 15 mm C.P. brass pillar tap

Providing and fixing vitreous China wash basin of approved make and colour with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm long PVC Inlet connection, 32 mm heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge White vitreous China wash basin size 630 x450 mm and equivalent sizes with single 15 mm C.P. brass pillar tap

Providing and fixing Satin finish stainless steel AISI 304 (18/8) kitchen sink of size 610 x 510 mm without drain board and bowl size 545 x 445 x 200 mm depth as per IS13983 of app roved make, with C.I. brackets, fittings and stainless steel plug 40 mm including painting the fittings and brackets with 3 coats of white enamel paint over a coat of primer, cutting and making good the walls wherever required complete as per specifications and as directed by the Engineer-in-charge

Providing and fixing 150 X150 mm heavy quality S.S soap dish case of approved make complete all as per specifications and as directed by the Engineer-in-charge

Providing and fixing C.P brass towel rail of approved make 600 mm long complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-incharge.

Providing and fixing 15 mm C.P brass 2 in 1 bib cock and Angle cock combinat ion of Heavy Quality of approved make as per specifications and as directe d by the Engineer-in-charge

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing swan neck sink cock of SS 304 garde heavy duty of approved make and as directed by the Engineer-in-charge complete

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of rollers, handles and locking mechanism fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately) and as directed by EIC Colour anodized aluminium section (minimum anodizing thickness of 15 micron)

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item) with bajra float glass of 5 mm thickness.

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item) with clear float glass panes of 5.00 mm thickness

Providing and fixing S.S. mosquito Jali 0.50 mm thick in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

Manufacture, supply and installation of louvers made of 4 mm thick aluminium composite panels of approved make in the external vertical face and flush with the facade system for inlet of fresh air as per the design / details including all necessary aluminium (with minimum 25 micron thick anodisation) frames, frosted glass in louvers and fixing portion, sub frames, peripheral flashings to avoid any ingress of water inside the building with stainless steel bird wire mesh on the inside etc. complete as per details in approved shop drawing and specifications and as directed by EIC

Providing and fixing 35 mm thick flush door shutters conforming to IS : 2202 non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with internal teak wood lipping 25mm wide and fixing with 4 Nos of 125 mm long Stainless steel Hinges with S.S. wood screws complete.

Providing and fixing decorative high pressure 1.0 mm thick laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS:2046 Type S including cost of adhesive, labour etc. complete as directed

Providing and fixing magnetic catcher double strip horizontal type 40 mm of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete .

Poviding and fixing FRP door shutters flush door / panelled type with plain colour or wooden veneer finish of approved make, design & colour. made out of 1.5 mm thick FRP skin moulded over wooden frame work of 40 mm wide and required thickness wooden styles and minimum 100 mm wide lock rails and wooden blocks for door stoppers, tower bolts, baby la tch, aldrop, handles etc. wherever required and core filled with Polyurethane Foam and fixing w ith 4 Nos 100 mm (ISI marked) stainless steel hinges with S.S. wood screws 30 mm thick panelled door type of approved colours including the cost of ISI marked 100 mm heavy quality stainless steel butt hinges with necessary screws

Poviding wood work in frames of doors, windows, clear story openings and other frames, wrought framed and fixed in position of required size and shape including sawing, jointing, making rebates for shutters, making grooves as shown in the drawings, finishing the surfaces to the required finish all as per specifications and drawings including necessary MS hold fasts 40 mm X 3 mm thick, 200 mm long / with coach screws including protective painting to the surface that will come in contact with walls, joining materials, labour etc. complete all as per s pecifications and as directed by the Engineer-in-charge. Second class teak wood

Providing and fixing cup board shelves or shutters using 18 mm thick prelaminated flat prssed 3 layer (medium density) particle board or graded wood particle board in shutter including 18 mm x 20 mm teak wood beadings at all sides with necessary screws ,handles,and other fittings all as per drawings and specifications and as directed by Engineer-in-charge

Providing and fixing sliding shutter using 6 mm thick prelaminated flat prssed 3 layer (medium density) particle board or graded wood particle board in shutter including aluminium bidding patti, sliding rollers at all sides with necessary screws ,handles,and other fittings all as per drawings and specifications and as directed by Engineer-in-charge

Providing and fixing pair of stainless steel "C" type door handles 10 mm dia, 125 mm long SS 304 grade solid rod , of specified size in steel doors/ wooden doors including screws / bolts etc. all as per drawings and specifications complete.

Providing and fixing pair of stainless steel "C" type door handles 10 mm dia, 250 mm long SS 304 grade solid rod , of specified size in steel doors/ wooden doors including screws / bolts etc. all as per drawings and specifications complete

Providing and fixing stainless steel aldrops of size 300 X 14 mm of approved make with necessary screws, bolting from rear side complete as per specifications complete.

Providing and fixing stainless steel tower bolts of size 250 X 12 mm of approved make with necessary screws etc.all as per specifications and as per drawings.

Providing and fixing tough & durable rim lock with two strong bolts having deadbolt and latchbolt with bigger keyhead and with 14 pin technology having weight of 900 gm. made from alloy steel with antique brass finish or approved finish with 4 keys along with lock plate, receptacle with 5 years manufacturers warranty etc complete as per the specifications and directions of Engineer-in-charge.

Providing and fixing S.S garde 304 heavy quality coat hook of size 650 mm long in as per specification and as direction of Engineer-in-Charge

Providing and fixing Drapery curtain rod 25 mm S.S. rods of 1.25 mm thick with bracket fixed with brass screws and wooden plugs etc. werever neccery including all material and labours as per specification and directed by the Engineer-in-charge

Shifting of materials from one place another place at the time of repairing of flooring and other miscellenious items when it is required and replace as same positioning after completion of work or as directed by engineer.

Providing and fixing box type mirrors of size 600 x 450 mm with shelves inside box of approved make , all as per specifications and as directed by the Engineer-in-charge .

Providing and fixing 6mm thick nylon rope colour and quality approved by Engineer-in-charge .

providing and fixing 40 mm dia PVC pipe 6kg/cm2 with elbow, Tee and other accessories

Providing and fixing corner glass shelf with cp brass bracket chrome (12''x12'') finish all as per specifications and as directed by the Engineer-in-charge .

Providing and fixing stainless steel 304 grade heavy sleek magnet door stopper with screw with heavy duty approved make and as directed by the Engineer-in-charge complete

Providing and fixing stainless steel tadi of size 250 X 12 mm of approved make with necessary screws etc.all as per specifications and as per drawings.

Providing Structural steel work using angles, channels, joists and other sections, welded and / or bolted in built up sections for trusses , structural steel floors, frame works, monorails and other structures including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Engineer in charge Up to and including 300 mm Joists, 350 mm channels, and below sections using materials from Approved vendor of BARC

Removal and refixing of 35 mm Flush doors including removal, refixing and at time of removal and refixing all damaged parts should be replaced with new i.e Hinges, tower bolts, aldops, handles, door stopers, nightlatch etc. including cost of all materials and labour as per specification and approved by Engineer-in-charges

Providing, wall painting with two coats on old/ new work premium plastic emulsion paint of approved brand and manufacturer) of required colour to give an even shade, including a coat of approved Cement primer ,including preparation of the surfaces, scaffolding complete as per specifications and as directed by the Engineer – In – Charge.

Providing and Painting with 1st quality acrylic washable distemper (ready made) with Two coats on new/old work of approved make and manufacturer and of required shade and colour, including scaffolding, reparation of the surfaces, etc., including a coat of approved cement primer.as per manufacturer's specifications and as directed by the Engineer-incharge.

Providing and applying white cement based wall putty of approved make over concrete or plastered surface upto 3 mm thick to get uniform surface free from undulation including cleaning complete all as directed by the Engineer-in-Charge.

Providing and painting TWO coats of synthetic enamel paint on Old/ new wooden surfaces of approved brand and manufacturer of required colour to give an even shade over an under coat of suitable shade primer of approved brand and manufacturer including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and Painting two coats on old/ new of synthetic enamel paint on steel surfaces of approved brand and manufacture to give an even shade over a primer coat .including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and fixing square mouth S.W. gully trap complete with CI grating brick masonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design 150 x 100 mm size gully trap "P" type

Supplying , cutting to shape and fixing specified diameter UPVC pipes as per IS 4985 for drainage line for building for toilet and bathroom waste collection pipe including bend , L bow fitting etc complete all as per drawings and as specified at site. dia 110 mm UPVC pipe

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation,finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels

Designing, providing and fixing of 4 mm thick approved make and shade Aluminium Composite Metal Panel of approved make cladding at different locations including soffits of over-hangs and including aluminium frame work with grids filled in with weather silicon sealant as per the drawings. The ACM panel composition shall be of 0.5 mm thick PVDF coated aluminium sheet + 3 mm thick low density polyethylene virgin resin core + 0.5 mm thick polyester (PVDF) coated Aluminium sheet all complete as per approved shop drawings and specification

providing Core cutting in brick masonary wall up to and including 50 mm Dia with including of 50mm dia PVC pipe with end caps upto the length of drilling hole etc completed as per direction of Engineer incharge.

providing and fixing good quality of kadappa stone for shelf below kitchen flatform and vertical supoort to kitchen platform including all and as directed bty Enginner incharge.

Supplying , cutting to shape and fixing specified diameter UPVC pipes having highest grade quality resin which ensures the fulfilment of basic need for clean & hygenic water.as per ASTM D 1785 standard in schedule 40&80 ( plain Ended) and fitting SCH80 as per ASTM D-2467 pressure class. it shuld be lead free material ensure safe drinding water ,excellent resistance to corrossion and chemical attack,simple and leak proof joint and including all fiiting etc complete all as per direction of Enginner incharge.

Providing and laying water proofing treatment in sunken portions of WCs, bath rooms etc. by applying cementslurrymixed with water proofing cementcompound consisting of applying: (a) 1st layer of slurryof cement@ 0.488 kg /sq.m mixed with water proofing cementcompound @0.253 kg per sq.m. including injecting cement slurry .This layer will be allowed to air cure for 4 hours. (b) 2nd layer of slurry of cement @ 0.242 kg / sq.m mixed with water proofing cement compound @ 0.126 kg / sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with cement slurry. Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (using crushed sand) admixed with proprietary water proofing compound conforming to relevant IS and approved by Engineer-in-charge including mixing 'RECRON 3S' fibre at the rate of 125 grams per 50 kg of cement in top layer of plaster and finally finishing the surface with trowel with neat cement slurry in bottom and all the sides of sunken portion. complete as directed by the Engineer-in-charge. The treatment to be tested for water tightness before filling the sunken areas.

Kores Sanitation

Technical Construction Company

R S CONSTRUCTION

OMKAR ENGINEERS AND CONTRACTORS