SPL REPAIR TO CERTAIN OFFRS MD ACCN AT VIKRAM VIHAR UNDER GE SOUTH, DELHI CANTT-10

M&L for providing and injecting chemical chlorpyrifos emulsifiable concentrate for Post Constructional Anti termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron, complete all as specified and directed.

M&L for anti termite Treatment of soil under existing floors using chemical chlorpyrifos emulsifiable concentrate @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of reinforcement to facilitate demolition (Parapet wall), complete all as specified and directed.

M&L for reinforced cement concrete (Design mix) M-25 (20 mm graded stone aggregate) as in fins, slab ,fascias, louvres, parapets, and railings, newels, balustrade, and the like, complete all as specified and directed.

S&F TMT bars 10 mm dia & over as in reinforcement of columns, beams, RCC, slabs, chajjas, lintels etc cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, welding the new reinforcement with old steel bars, complete all as specified and directed.

S&F TMT bars 8mm dia as in reinforcement of RCC of any description, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified & directed.

M&L for use & waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beams for rough finished surfaces of concrete, complete all as specified & directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified & directed.

M&L for brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6 (upto two storey bldg), complete all as specified & directed.

Demolition of bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer) laid, bedded and pointed in any mortar, complete all as specified & directed.

M&L for demolition of mud in roof, any thickness, including plastering and leeping upto two storey bldg including necessary scaffolding arrangement (whether full thickness removed or only a part there of) and removing from cantonment area or as directed, complete all as specified and directed.

M&L for Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in roof padding , finished even and smooth without using extra cement ,including cleaning the concrete surface by steel wire brushes, up to three storey bldgs, complete all as specified and directed.

M&L for APP based polymeric membrane one side rough finish (to receive SRI tile) and other side plain finish, minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (weight not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints, complete all as specified & directed.

S&F for Heat Resistant Terrace ceramic cool Tiles (300 mm x 300 mm x 10 mm minimum) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface up to 3 cuts complete, including providing skirting up to 150 mm height along the parapet walls in the same manner, complete all as specified & directed.

M&L for cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate in roof kerbs or mud stops, rounded or chamfered and hold fast on edge including necessary form work, complete all as specified & directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar, complete all as specified & directed.

M&L for Granite (of any type) work, 18-20 mm thick jade black (table rubbed and polished) in cooking platforms, lift wall, skirtings where ever required and likes on cement mortar bedding of 20mm thick in cement mortar 1:4 including pointing in white cement using marble dust with admixture of pigment to match, complete all as specified and directed. Notes: (a) Additional 75mm width patti shall be measured separately. (b) Minimum rate of granite should not be less than Rs. 1500/- per Sqm including GST.

M&L for Udaipur green marble work 18 to 20mm thick (table rubbed and polished) in window-cills,on floor and like in 20 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble of any shade other than white and black, complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified & directed.

M&L for glazed ceramic coloured tiles of size 600mmx300mm, thickness 7 to 8mm as in vertical surfaces such as wall, pillar, skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.

M&L for Vitrified ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm of size (600mm X 1200mm), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed in cement mortar (1:6), complete all as specified and directed.

All as per Srl item No. 22 above but as in skirting including 10 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L Non Skid ceramic tiles 8 to 10 mm thick (square/rectangular) area of each tile 600 x 600 mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick ( square / rectangular) area of each tile exceeding 0.11 sqm but n exc 0.18 sqm, as in skirting laid on 10 mm thick cement plaster in cement mortar (1:4), set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cement to match the shade of tiles, complete all as specified and directed.

S&F in repairs Vitreous china wash down water closet pan single piece syphonic action, white including soft close sheet cover of closed pattern with flat bottom including dual flushing cistern viterous china 10 ltr capacity, complete all as specified and directed.

S&F in repairs Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, coloured with integral foot rests including provision of lime concrete bedding complete.Squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc including making good to floor, complete all as specified and directed.

S&F in repairs PVC low level white flushing cistern valveless symphonic action type 10 lts capacity IS marked with inlet, ball valve, float and handle including PVC flush pipe 32 mm dia with bend and a pair of mild steel angle iron brackets of suitable size including making necessary connections to water supply pipe line and WC,(ISI Marked), complete all as specified & directed.

S&F in repairs CP brass health faucet with hand shower and 1.5 mtr flexible stainless steel pipe suitable for fixing to 15 mm dia pipe, complete all as specified & directed.

S&F in repairs Toilet paper holder of mild steel Chromium plated ‘D’ type, fixed to walls with chromium plated brass screws, complete all as specified & directed.

S&F in repairs Vitreous china wash basin with pedestal white, flat back, size 550 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete all as specified & directed.

S&F in repairss elegent mirror PVC cabinet without towel rail of size 422 x 622 mm, complete all as specified & directed.

S&F in repairs stainless steel foldable towel rack 60 cm long and 24 cm deep with towel rail and hangers at bottom fixed to walls, complete all as specified and directed.

S&F in repairs brass chromium plated shower rose of size 125 mm with long arms (300 to 450 mm ) including fixing to CPVC, complete all as specified and directed.

S&F in repairs 6 mm thick glass corner shelf fancy type with railing and fitting complete of size 25cm x 25 cm of best quality (as per sample approved by Engr -in-charge), complete all as specified and directed.

S&F in repairs wash hand basin mixer single lever 15mm dia CP brass fancy type including joints to CPVC pipe or unions, complete all as specified and directed.

S&F in repairs Brass CP Wall mixer (Non Telephonic Type) with L bend 3-in-1 for mixing hot & cold water screwed down for CPVC pipe 15 mm bore and fixed, complete all as specified and directed.

S&F in repairs Kitchen sink mixer 15mm dia CP brass fancy type including joints to CPVC pipe or unions, complete all as specified and directed.

S&F in repairs 15 mm bib tap, brass chromium plated fancy type (quarter turn), long body screwed down including necessary extention piece, complete all as specified and directed.

S&F in repairs 15 mm dia brass chromium plated angle valve fancy type (quarter turn), screwed at ends including necessary extention piece and fixed, complete all as specified and directed.

S&F in repairs 15 mm dia 450/600mm long PVC connections with brass check nut, complete all as specified & directed.

Taking down (Door) chowkats or frames with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames), complete all as specified & directed.

Taking down (Door) chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (without taking off shutters from the frames), complete all as specified & directed.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge. Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65 x100 mm comprising of vigin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ricehusk/wheat husk) and non toxicadditives (maximum toxicity index of 12 for 100 g,s) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (MS hold fast/hugs or SS dash fasteners shall be paid for separately) Note:- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge. Note: stainless steel butt hinges shall be paid separately under relevant item.

Providing and fixing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof,fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardwares shouldbe fixed with 19*6mm size steel screws etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawings. Note: Fixture/fittings shall be measured & paid under relevant item

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge. Note: stainless steel butt hinges shall be paid separately under relevant item.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge. Note:For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e., depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter for cupboard of size 19 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge. Note: stainless steel butt hinges shall be paid separately under relevant item.

S&F factory made Aluminium window as per TD drg No. CEDZ/D-316 (for reference only) outer frame 40 mm x 114 mm with 1.3 mm thickness corner 45 degree vut and aluminium welded centre horizontal member size 40mm x 65mm also welded top hung shutter (01 No) size 40 mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp, 12 mm SS 202 grade round bar at 100 mm c/c distance in handle 150mm c/c distace for safety grill welded at both ends with 6 mm SS 202 grade round bar 5 mm clear glass both side EPDM rubber gasket between (for openable shutter and fixed pan) hand lovar type single point lock, SS 75 mm long hinge & PVC magnet, full system powder coated with pure polyser coat of any shade as approved by GE and installing with silicon, complete all as specified and directed. Note : For installation of window AC/desert cooler the provision of window glass shutter, grill and necessary fittings and locking arrangement for subject portion will be modified as per ground requirement during the execution as per direction of Engineer-in-Charge.

S&F factory made Aluminium window as per TD drg No. CEDZ/D-316 with following specifications :- (i) Outer frame of size 40mmx114mm with 1.3mm thickness, corner 45 degree cut aluminium welded (ii) Center mullion of size 40mmx65mm (iii) Welded shutter (02 nos) of size size 40mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp with 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock, aluminium kobra hinges 2 Nos per shutter (iv) 12mm SS 202 grade round bar safety grill at 100mm cc distance modified to 150mm cc distance in front of handle, welded at both ends with 6mm SS 202 grade round bar (v) Welded wire mesh shutter(02 nos) of size 40x18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) Entire window shall be powder coated with pure polyster coat of any shade as approved by GE (vii) Window shall have provision for installation of window AC/Desert Cooler and provn of window glass shutter, wire mesh, grill and necessary fittings and locking arrangement for subject portion will be modified as per ground requirement during the execution as per direction of Engr-in-charge. (viii) Window shall be installed with silicone complete all as specified and directed by Engineer-in-charge.

S&F in repairs for Mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165, complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer, complete all as specified and directed.

S&F in repairs for mild steel, 300 mm ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

M&L for preparation of old steel surfaces of any description not otherwise described over 10 cms width or girth and apply one coats of synthetic enamel paint, complete all as specified and directed.

S&F 100mm long (size) butt hinges, stainless steel AISI 304 grade with brass/bronze hinge pin, complete all as specified and directed.

S&F Stainless steel AISI 304 grade barrel tower bolt 200mm long, extruded section,etc. complete all as specified and directed.

S&F Stainless steel AISI 304 grade handle of size 200mm long,etc. complete all as specified and directed.

S&F Stainless steel of AE SI 304 Grade, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F Magic eye and fixed to doors, complete all as specified and directed.

S&F Hasp and staple 100 mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws, complete all as specified and directed.

S&F Floor door stopper (double leg) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm, complete all as specified and directed.

S&F, 25mm dia SS curtain rods, 1.2 mm thick, fency type, including SS bracket and SS side bulb decorative type complete for doors and windows as required, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C1 using 20mm graded stone aggregate in plinth protection, 75mm thick, finished fair and even without using extra cement, complete all as specified and directed.

M&L for forming Construction joints 30mm deep x 10mm wide, filled with sealing compound grade ‘A’, complete all as specified & directed.

Taking up or down steel tubing 15 mm bore and connection including cleaning for refixing if required, complete all as specified and as directed.

Taking up or down steel tubing 20 mm bore and connection including cleaning for refixing if required, complete all as specified and as directed.

Supplying and laying of CPVC 20mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including brass coupling fittings as required, complete all as specified and directed.

Supplying and laying of CPVC 25mm OD pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including brass coupling fittings as required, complete all as specified and directed.

S&F 20mm outer dia CPVC pipes SDR 11 with and including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified and directed.

S&F 25mm outer dia CPVC pipes SDR 11 with and including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified and directed.

S&F 20mm outer dia CPVC Union, complete all as specified and directed.

S&F 25mm outer dia CPVC Union complete all as specified and directed.

S&F 25mm outer dia CPVC Tank Adaptor, complete all as specified and directed.

S&F 20mm outer dia CPVC Tank Adaptor, complete all as specified and directed.

S&F 25mm outer dia CPVC ball valve/gate valve complete all as specified and directed

S&F 20mm outer dia CPVC ball valve/gate valve complete all as specified and directed

S&F 20mm outer dia CPVC Brass Elbow complete all as specified and directed.

S&F 20mm outer dia CPVC Male Brass Threaded Adapter (MTA/BTA) complete all as specified and directed

S&F 25mm outer dia CPVC Male Brass Threaded Adapter (MTA/BTA) complete all as specified and directed

S&F 20 mm outer dia CPVC Brass Tee, complete all as specified and directed

Dismantling water tanks of capacity exceeding 500 litres but not exceeding 1000 litres, complete all as specified and directed

Dismantling water tanks of capacity exceeding 250 litres but not exceeding 500 litres, complete all as specified and directed

S&F 500 ltr capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) white colour hoisted and fixed in position, complete all as specified and directed

S&F 1000 ltr capacity rotational moulded triple layered polyethylene water storage tanks (cylindrical vertical with closed top) white colour hoisted and fixed in position, complete all as specified and directed

S&F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore, complete all as specified and directed

S&F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25 mm bore complete all as specified and directed.

S&F in repairs Sinks with drainage board made of 1mm thick stainless steel for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, including PVC waste pipe 32 mm bore, 65 cm long, complete all as specified and directed

S&F Sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed

Dismantling of cast iron or reinforced concrete drains pipes, jointed in cement morter and taking out of trenches if required up to 100 mm internal dia of drains, complete all as specified and directed.

S&F 110 mm uPVC pipes Type 'B' (for waste water), single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls, complete all as specified and directed.

S&F 75 mm uPVC pipes Type 'B' (for waste water), single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls, complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size, material or pattern), including all fittings , heads, shoes, bends,swann necks, etc including taking out of trenches if required for cleaning or refixing or removal to store, complete all as specified and directed.

S&F 110 mm uPVC pipes Type 'A' (for rain water), single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S&F 110 mm uPVC (SWR) Bends/ Tees/ Tapers (any radius), with or without oval access door as required, complete all as specified and directed.

S&F 75 mm uPVC (SWR) Bends/ Tees/ Tapers (any radius), with or without oval access door as required, complete all as specified and directed.

S&F in repairs uPVC multi floor trap with grating including jointing with solvent cement, dia of outlet 75mm, complete all as specified and directed.

S&F Stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof for any bore and any type of pipes, complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc including removal of debrish from the MOD land, complete all as specified and directed.

M&L rendering 10 mm thick in cement mortar (1:6) on faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for expose the first joint of masonry structure at ground level horizontally. The plaster must be knocked off at least 50 cm beyond the visibly penetrated area. Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm, Drilling Holes : Drilling holes 10mm diameter in masonary structure along the side of the joint as per manufacturer's instructions so as to cross the brick/ block at the intervals spacing of 15-30cm depending on extent of rising dampness as per recommendation of engineer in charge, Cleaning of holes : Clean the holes by air blower prior to fixing nozzles. Install latex polymer packer injection packers 9.8mm diameter, 10cm long in the holes and tighten. Fix the packer securely using sealent, Cutting of Packers : Cut the packers after completion of grouting without damaging structural elements, complete all as specified and directed.

Supply and apply of a 3 part, very low viscous, elastic polyacrylic injection resin with a versatile and adjustable reaction time having Mixed viscosity : 3-11 M.pa.s at +20 Deg C, Reaction time : adjustable according to ambient temperatrure and execution requirement between 8-50 mins, pH – 9-10, tested as per Wissbau No. 2002-094-(1A) – Function test with re-injectible hose system. The holes should be drilled until a depth of approx 5 cm (for a 6cm thick wall) before the end of the wall is reached. Pump injcection of polymer resin compound at >20 bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas. If voids in masonry being injected contain insufficient moisture to activate the grout inject a small amount of water prior to injecting the grout. When movement stops or polymer compound appears at the packer move to the next packer and inject. If the dampness is heavy, inject similarly at next joint line (on average 200 ml for each hole, total 600 nos hole for 04 block), complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces, applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) mixed with water proofing compound as per manufacturers instructions, finished even and fair, complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:6 on internal brick/concrete wall surfaces of any description and finishing the surfaces even and fair without using extra cement, complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling, finished even and fair without using extra cement, complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of walls/ceiling applying wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two or more coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete as per manufacturer's specifications and directed.

M&L for preparation of old decorated surface (plastered or unplastered) of walls/ceiling by complete removal of existing treatment by mechanical grinder and applying water proof wall care putty of 1 mm thickness over plastered surface to prepare the surface even and smooth to receive primer and applying one coat primer & two or more coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour, complete as per manufacturer's specifications and directed.

M&L for preparation of newly plastered surfaces of walls and providing and applying putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of walls, complete removal of existing treatment by rubbing, brooming down, washing with water etc and providing and applying plaster of Paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails, complete all as specified and directed.

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer-in-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company, complete all as specified and directed.

S&F Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and esistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixinng stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company, complete all as specified and directed.

S&F CP clip on hinges (Inset), complete all as specified and directed .

S&F 15mm mild steel, chromium plated rod with fixing brackets, fixed in cupboards for hanging cloth of adequate strength, complete all as specified and directed.

S&F Stainless steel AISI 304 grade handle of size 100 mm long,etc, complete all as specified and directed.

S&F Magnetic catch for wooden cupbord with complete closer macanigum claps and clips fix with stainless steel screw, complete all as specified and directed.

M&L for cleaning the sides Box hinges for Garage door of frame and shutters shafts guide channel and greasing of moving parts and straightening opening and closing and replacement of bolts nuts etc as required for smooth functioning of shutters and taking out existing shutters if required and refixing the same in original position complete all as specified and directed (opening of shutter exc 2.00 m and not exc 3.50 m and area exc 6.00 sqm and n.exc 9.00 sqm)

S&F in repairs mild steel box type hinges of approved make in existing shutters/opening of shutters exc 2.00 m and n.exc 3.5 m, complete all as specified and directed.

S&F Stainless steel plate rack made of 1 mm thick stainless steel sheet of size 750 mm x 900 mm x 210mm consisting of 3 shelf for bowls and one shelf for keeping six nos of big utensil and seven nos of small utensils divided by 10 mm dia stainless steel hollow pipe @ 60 mm centre to centre or as per drg and sample kept in GE"s office, complete all as specified and directed.

S&F in repairs Stainless steel telescope channel of size 300MM to 500mm, complete all as specified and directed.

S&F Stainless steel thali basket for kitchen cabinates of suitable size and shape complate all as specified and directed

Providing conveyance for transportation of luggage including packing (Bubble wraps and cardboard reqd) and shifting and re-installation of household items at new location like TV-01 No, AC-01/ 02 Nos (removal and re-installation of windows/split ACs incl gas filling if reqd), referigerator-01 No, Washing Machine-01 No and Water Purifier- 01 No). Note :- Transportation of Two Wheelers and Four Wheelers not incl above.

ROAD, PATH AND CULVERT Surface dressing n exc 15cm deep in soft/loose soil, complete all as specified & directed.

M&L for Hard core of gauge n exc 63mm using broken stone or boulders, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface, complete all as specified & directed.

M&L for 100mm thick PCC (1:3:6), nominal mix, type C2, using 40mm graded crushed stone aggregate as in sub base of floor, finished even and fair, complete all as specified and directed.

M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade confirming to IS-15658-2006 of approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified & directed.

Removing soil, excavated material to a distance exc. 250m but n exc 500m and depositing where directed at a level n.exc. 1.5m above the starting point, complete all as specified and directed.

M&L for PCC (1:2:4), nominal mix, type B-1, using 20mm graded crushed stone aggregate as in edging of path area or mud stops and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified & directed.

INTERNAL ELECTRIFICATION Taking down carefully aluminium/copper point wiring (light/fan/bell/socket /power) with complete fittings such as steel terminal boxes, switches, ceiling roses, pendents, regulators, sockets etc and removing the material including making good the distrubed surfaces of the wall flooring ceiling etc to match the existing surface, complete all as specified and directed.

M&L for concealed point wiring complete with stranded copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit and including replacement of unserviceable pressed steel terminal boxes with Modular steel terminal boxes factory made including white cover modular plate with frame suitable for modular switches, modular sockets, modular fan regulators etc of required size complete including 1.5 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for One light/Fan/Bell point controlled by one 5 Amp switch one way using cable (1.5 Sq mm for phase and neutral and 1.5 sqmm for earthing) . Note :- The rates are inclusive of cutting / chasing and making good disturbed surfaces with cement mortar 1:3 and applying same finishes with adjoining surfaces of disturbed area with OBD/ Colour wash/ white wash etc as per site requirement.

All as per Srl item No. 133 above but one three pin 6 Amp socket outlet point controlled by one no, one way switch on same board.

All as per Srl item No.133 here in before but for one three pin socket outlet 6 amps point controlled by one no, one way switch on independent board.

All as Srl Item No 133 here in before but for one socket outlet 6/16 Amps on Independent board with cables 2.5 sqmm size for phase and neutral and 2.5 Sqmm for earthing.

All as per Srl item No. 133 here in before but for one light point controlled by two nos., two way 6 Amp switches.

M&L for concealed point wiring complete with stranded copper conductor 4 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit complete including 4 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for one socket outlet for modular AC Box on Independent board with cables 4.0 sqmm size for phase and neutral and 4 Sqmm for earthing, complete all as specified and directed. Note :- The rates are inclusive of cutting / chasing and making good disturbed surfaces with cement mortar 1:3 and applying same finishes with adjoining surfaces of disturbed area with OBD/ Colour wash/ white wash etc as per site requirement.

S&F switch modular type, 1 way 6A, 1 module, complete all as specified and directed.

S&F Modular Socket, 6A - 2/3 pin 2 module, complete all as specified and directed.

S&F switch modular type 1way 16A, 1module with indicator, complete all as specified and directed.

S&F Modular Socket 6A/16A - 2/3 pin combined, complete all as specified and directed.

S&F Modular Bell push 6A 1 module, complete all as specified and directed.

S&F in replacement Decorative wall light mounting suitable for LED Lamp with 15 Watt lamp with all connections, complete all as specified and directed.

S&F 20 Watt wall mounted LED batten capable of delivering minimum 2000 lumen having PC diffuser luminous efficiency not less then 120 lumen/Watt CRI>80% PF>0.9,CCT 6500K independent isolated SPMS based constant current electronic LED driver with THD < 10% surge protection and other safety tests as per IS 15885( Part-2/Sec-13) : 2012 polycarbonate diffuser housed in power coated white extruded aluminum channel housing , white colored ABS end caps IP 20protection input voltage range 140-270V input frequency 50-60Hz including electrical connection with 3 core flexible copper conductor cable of appropriate size from ceiling rose to fixture, complete all as specified and directed.

S&F 10 Watt wall mounted mirror LED batten capable of delivering minimum 1150 lumen having PC diffuser luminous efficiency not less then 120 lumen/Watt CRI>80%, PF>0.9,CCT 6500K independent isolated SPMS based constant current electronic LED driver with THD < 10% surge protection and other safety tests as per IS 15885( Part-2/Sec-13) : 2012 polycarbonate diffuser housed in power coated white extruded aluminum channel housing , white colored ABS end caps IP 20protection input voltage range 140-270V input frequency 50-60Hz including electrical connection with 3 core flexible Cooper Conductor cable of Appropriate size from ceiling rose to the fixture, complete all as specified and directed.

S&F Modular AC Box with socket and MCB SP 20 Amp complete with Metal box , white colour plate and frame complete in replacement of sheet metal enclosures as per site requirement, complete all as specified and directed.

S&F LED bulb 12 Watt, CRI 80, Frosted glass, non dimmable 6500k white 100 Lumens/watt Pf <0.90, Min 25000 Hr IP rating 20, complete all as specified and directed.

S&F Electric bell Ding Dong type AC, 230 volts single phase, complete all as specified and directed.

S&F Ceiling rose surface Bakelite 65x25mm two to three terminals, complete all as specified and directed.

S&F in replacement LED bulk head in engineering plastic housing with clear prismatic diffuser, 10W WHITE in replacement of old unserviceable bulk head fitting including all accessories connecting up twin core flexible copper conductor cable, complete all as specified and directed.

S&F in replacement of building security light fitting 35W LED 5000K new powder coated pressure die cast aluminium compact LED Street light including fixing on pole with bracket of suitable dia duly fixed with clamps, nut, bolts & washers etc, complete all as specified and directed. Note : Suitable size of GI bracket and clamps are included in quited rates.

Taking Down ceiling fan and refixing it back after repair and B/R works all as specified and directed by Engr in charge.

S&F Exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V , 50 Hz RPM 1200 copper winding sweep 250mm, complete all as specified and directed.

Taking Down of Geyser any type any size including disconnection of electrical connection and water connection and keeping in safe coustody and deposit it to MES store yard, complete all as specified and directed.

S&F Water storage heater of capacity 25 ltr, 5 star rated, vertical type, porcelain enamel glass lined tank with glass lined incolony element, 3.5 cm thick polyurethane foam (PUF) insulation, tank design should be suitable to withstand 8 bar pressure suitable for pressure pumps and multi storied building, triple safety, sacrificial magnesium anode for corrosion protection, ABS design body, IPX4 waterproof technology, AC, electric, 230 volt, 3 core lead, safety valve, PRCD Plug top including electric and water connection SS threaded and making good to disturbed surfaces including taking down existing water storage heater, complete all as specified and directed. Note : Electric switch for geyser of 16 Amps shall be provided on main switch board of the bathroom and socket outlet near the geyser and will be measured under relevent item of this schedule.

S&F in replacement of sheet metal enclosures double door for DBs when MCBs to be used SPN-08 Way with rubber gasket, 240V, prewired with proper protection class IP-65, complete all as specified and directed.

S&F in replacement of sheet metal enclosures double door for DBs when MCBs to be used SPN-12 Way with rubber gasket, 240V, prewired with proper protection class IP-65, complete all as specified and directed.

S&F in replacement of sheet metal enclosures double door for DBs when MCBs to be used SPN-4 Way with rubber gasket, 240V, prewired with proper protection class IP-65, complete all as specified and directed.

S&F RCCB, 240Volts, Double pole 30mA breaking capacity 63 A all as per site requirement, complete all as specified and directed.

S&F RCCB, 240Volts, Double pole 30mA breaking capacity 40A all as per site requirement, complete all as specified and directed.

S&F in replacement MCB SPN 63 Amps 'C' series, breaking capacity 10 Ka, 240 volts, 50 Hz including necessary incoming and out going electric connection with suitable size of copper lugs etc, complete all as specified and directed.

S&F in replacement MCB SPN 40 Amps 'C' series, breaking capacity 10 Ka, 240 volts, 50 Hz including necessary incoming and outgoing electric connection with suitable size of copper lugs etc, complete all as specified and directed.

S&F for MCB SP 6 to 32 Amps 240 Volts, 10kA, `B' curve all as per site requirement, complete all as specified and directed.

Taking down unserviceable sub main wiring twin core of any size complete and making good disturbed surface, complete all as specified and directed.

M&L for Sub Main wiring using single run PVC FRLS grade insulated unsheathed, multistrand copper conductor cable 2 runs of 10 Sqmm for phase and neutral and 1 run of 10 Sqmm for earth wire drawn through concealed PVC conduit wiring in wall not less than 25mm dia with all fittings like tees, bends, junction/ terminal boxes etc as per site requirement, complete all as specified and directed. Note:- Phase should be of Red /Yellow/Blue, neutral should be of black and earthing wire should be of green colour. 2 runs of cable for phase/ neutral and 1 run for earth will be measured and paid as one unit length.

S&F Wall mounted fully automatic domestic type electric chimney in size of 90 cm hood for 2-3 gas burners of suction capacity min 1200 mtr cube/hr, touch , gesture control, filterless, autoclean, noise level max 60 db, with metal oil collector and suitable size duct pipe including all connecting accessories,fitting and fixtures, complete all as specified and directed Note :- Work for fitting of chimney including hole of suitable size for outlet will be done by contractor without any extra cost.

S&F Wall mounted fan made of sturdy engineering plastic complete voltage 230V, 50 Hz, copper winding of sweep 400m, complete all as specified and directed.

Taking Down existing exhaust fan of kitchen/toilet including closer of hole across the wall complete with B/R finishing work and refixing the same after repair work at new or existing places, complete all as specified and directed.

Supply and fixing of PVC conduit medium grade of size 15mm for TV connection and Socket /Telephone socket, complete all as specified and directed.

Supply and fixing TV Co-Axial Socket 1 module, complete all as specified and directed.

Supply and fixing Telephone socket 1 module, complete all as specified and directed.

Supply and fixing Flush metal box 1 module, complete all as specified and directed.

Supply and fixing white cover plate with frame 1 module, complete all as specified and directed.

S&F PVC connection with brass nipple 15mmx 600mm long with ISI marked stainless stell suitable for hot and cold water of 25 ltr capacity of geyser as hot and cold water connection, complete all as specified and directed.

S&F Switch Modular type switch, 6 A 2- way 1 Module switch with finger proof terminal, complete all as specified and directed.

Supply & fixing fan regulator step type 2 module 230 V , 50 Hz, complete all as specified and directed.

Supply & fixing of water storage heater, 5 star rated with Marine grade glass line coating Tank Efficient long life copper heating element, Adjustable Thermostat, Shock resistant and rust proof engineering thermoplatic body, IPX4 waterproof technology, Tank design is suitable to withstand 8 bar pressure (Geyser) of capacity 06 litre ISI mark, , AC, electric, 415 volt, complete, 3 core lead, including safety valve, including electric and water connection complete all as specified and directed by Engineer-in-charge. Note : Electric switch for geyser of 16 Amps shall be provided on main switch board of the bathroom and socket outlet shall be provided near the geyser and will be measured under relevant item of this schedule.

Please Enable Macros to View BoQ information