PROVN OF TOILET AND BATHROOM BLOCK NEAR BLDG NO TWG-108 AND109 OF TPS LIVING OF 22 RAJPUT WITH FWD FACILITIES AND CHEQUERED TILING FLOORING IN FRONT OF BLDG NO TWG-99 AND OTC-EC-45-910-3794 UNDER GE TAWANG

Amount

B/R Items Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil completed all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15 cm deep and getting out in hard / dense soil completed all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth for foundation, etc. or for shaft, wells, cesspits, manholes, pier holes, etc,. Not exceeding 10 Sqm on plan and not exceeding1.5 m depth and getting out in hard/dense soil completed all as specified and directed.

M & L for hardcore of broken stone/boulders gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface completed all as specified and directed.

M & L for cement concrete in foundation, filling and mass concrete in type D2 1:4:8 (40mm graded aggregate) completed all as specified and directed.

M & L for walling of random rubbles uncoursed, well bonded bedded and solidly hearted built in CM 1:6 (below ground level) complete all as specified and directed.

M&L formwork to sides of concrete foundations, footing, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter completed all as specified and directed.

M &L for RCC nominal mix type B-1 (1:2:4) 20mm graded aggregates foundation, including rafts footings, foundation beams, plinth beams: bases for columns, etc: basement slabs, under reamed piles and mass concrete completed all as specified and directed.

M & L formwork for fair finsihed surface to sides of pillars, posts, struts, piers, columns and stanchions completed all as specified and directed.

M&L for RCC nominal mix type B-1 (1:2:4) (20 mm graded aggregate) Columns, pillers, post & structurs completed all as specified and directed.

M& L for TMT bars 10mm dia and over, reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (anealed)not less than 0.90mm dia, complete all as specified and directed.

M & L for TMT bars 8 to 10 mm dia in stirrups, spacers and binders, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (anealed)not less than 0.90mm dia, complete all as specified and directed.

M&L for PCC 1:3:6 type-C1 20mm graded aggregate in pre-cast cement concrete block masonry with solid blocks exc 10cm in width and setting in CM 1:4 completed all as specified and directed.

M & L for PCC (1:3:6) type C-1 using 20 mm graded stone aggt solid building block set in cement mortar 1:6, n exc 10 CM complete in walls completed all as specified and directed.

M & L rendering 10 mm thick on fair faces of brick/concrete work CM 1:4 rough to received tiles rough finsihed completed all as specified and directed.

M & L rendering 15mm thick on fair faces of brick/concrete work CM 1:6 rough to received tiles rough finsihed completed all as specified and directed.

M & L for three coat of white washing on new plaster wall surface over primer including preparation of plastered surfaces complete all as specified and directed.

M & L for two coat of cement pase paint on plastered surfaces with one coat priming over alkali resistant priming paints on new surfaces including preparation of surface complete all as specified and directed.

M & L 75mm thick PCC type D2,1:4:8 (40mm graded stone aggregate as in sub base of floor compete all as specified and directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in sub-base of floors, plinth protection finished the surface of concrete fair and even, complete all as specified and directed.

M & L 25mm thick PCC (1:2:4) type B-1 (20mm graded aggregate) as in sub base finishing the surface even and rough to receive the topping layer completed all as specified and directed.

M&L 15mm thick, screed bed or bedding layer, in cement mortar (1:6) for laying floor tiles etc, complete as specified and directed.

M & L screed bed or bedding layer of mortar (1:4) 15mm thick for laying floor finishers completed all as specified and directed.

M & L non-skid ceremic tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match completed all as specified and directed.

M & L for coloured glazed ceramic tiles in vertical surface 300 x 200x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match completed all as specified and directed.

S & F second-class hard wood timber scantlings, wrought timber framed and fixed in any position with nails completed all as specified and directed.

S & F 4mm thick plywood, grade BWR, type BB, fixed with nails to timber framework as in ceiling etc complete all as specified and directed.

S& F steel work in tubular trusses including special shaped washer etc. complete usng ERW or induction butt welded tubes comforming to IS 1161 grade st-240 for Roof trusses (framed), trussed, purlins, completed all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws completed all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws completed all as specified and directed.

S & F second class hard wood plain, solid, straight chowkhats and frame, wrought, framed rebated on the soild, rounded or chamfered, put together with glue pinned at joints completed all as specified and directed.

S & F 30 MM thick 2nd classs hard wood glazed and skelton shutter open rebated and prepaired to receive glass gauze etc, divided into squares (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for secuering glass etc size of members of shutter as specified in SSR part-I, sec 8 clause 8.24 (a) completed all as specified and directed.

S & F plain framed, panelled shutter 35mm thick (two panel) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. 2nd class HW rail & style of size as per IS: 1003 (Part I), Kiln seasoned & chemically pressure treated completed all as specified and directed.

S & F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube completed all as specified and directed.

S & F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail Panelling of plain colour PVC sheet to be fittted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site completed all as specified and directed.

S & F 100 mm long butt hinges medium grade cold rolled mild steel and fixed completed all as specified and directed.

S & F alluminium anodised barrel tower bolts 150mm of extruded section and fixed completed all as specified and directed.

S & F 150mm long aluminium handles cast type anodised completed all as specified and directed.

S & F aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed completed all as specified and directed.

S & F 75 mm long butt hinges medium grade cold rolled mild steel and fixed completed all as specified and directed.

S & F alluminium anodised barrel tower bolts 125mm of extruded section and fixed completed all as specified and directed.

S & F 100mm long aluminium handles cast type anodised completed all as specified and directed.

M & L 3mm thick sheet glass, ordinary quality and glazing with oil puty in square n exc 0.5 sqm in each plane completed all as specified and directed.

M&L for preparation of new wood surfacesof any description exc 10CM width or girth and applying two coat of synthetic enamel paint over a coat of pink primer completed all as specified and directed.

M & L for 75mm thick PCC 1:3:6 type C2 40mm graded aggregate as in plinth protection, finishing the surfaces even and smooth without using extra cement completed all as specified and directed.

S & F in vitreous china squatting pan of orrisa pattern size 580X440 mm wide , with intigral foot rest (excluding down pipe and flush pipe) complete all as specified and directed

S & F PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, of capacity 10 Litres, including brackets, flush pipe, fixed in repairs complete all as specified and directed.

S&F vitreous china wash basin, white, flat back, size 580x450mm Taps, waste, chain and plug and porcelein stopper butincluding cutting for aned pinning in ends of brackets or erecting stand completed all as specified and directed.

S&F in repair vitreous china urinal, half stall type, white incl flush pipe, waste pipe, coupling, urinal spreader, complete all as specified and directed. Make : Cera. (Note : contractor should resolve the complain within 24 Hrs and should give feedback to the Engineer in charge).

S 7 F pillar taps 15mm bore dia, cast copper alloy with capstan heads, chromium lated, screwed down high pressure, with or without lettered 'Hot' or Cold with long shanks and fly nuts, screwed for iron pipe and fixed completed all as specified and directed.

S & F stop cock 15mm dia CP high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union completed all as specified and directed.

S&F for 20mm outer Dia 3-layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc completed all as specified and directed.

S & F PVC (SWR) pipe 75mm bore single socketed, in any length with rubbber ring joints, laid in trenches or floor completed all as specified and directed.

M & L PVC (SWR) floor trap with grating including jointing with sovlent cement of 75mm dia completed all as specified and directed.

S&F soap dish, viterous china white, appx size 160x160x90mm completed all as specified and directed.

S&F for Towel Rail 450mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms completed all as specified and directed.

S & F 15 mm bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed completed all as specified and directed.

Returning, filling in, including spreading, levelling watering and well ramming in layers not exc 25 CM completed all as specified and directed.

Removing excavated soil exc. 50m but n exc 100m & depositing where directed at a level n exc. 1.5 m above the starting point completed all as specified and directed.

S & F for FE 410-W (Gde-E-250) quality A joist, channel, angle or tee section fixed independently without connectiong plates etc cut to ordinary length within 20mm of the length indicated) Size of Angle 70 X 70 X 7mm completed all as specified and directed.

S&F mild steel flat bar 40X6mm size of nearest suitable as ordered in required length including drilling hole for bolts notching for securing wire mesh etc confirming to Fe 290 Grade E-168 completed all as specified and directed.

S&F mild steel screw bolt (machine made) with hexagonal at one ends and screwed the other ends, each screwed ends to be fitted with washer and one hexagonal nuts, size of bolt 12mm dia and length (from under side of head to the end in 75mm), complete all as specified and directed.

M&L Chequered cement concrete tiles 200mmx200mmx25 mm thick, set jointed and pointed in neat cement slurry using grey cement and pointed with white cement and pigment as in paving/foot path etc as required complete as complete all as specified and directed.

E/M Items M&L for point wiring with 2 single core FRLS PVC insulated, unsheathed stranded copper conductor of size 1.5 sqmm in and including suitable size PVC casing & caping with teak wood boxes and 3mm thick plastic laminated sheet top cover for light/fan/socket controlled by one switch complet with 1.5 sqmm PVC insulated unsheathed multistandard copper conductor 1100 volts grade green colour for earth continuity completed all as specified and directed.

All as per item No 65 here-in-before but for one 5 amp socket outlet independent board complete all as specified and directed

All as per item No 65 here-in-before but for one 5 amp socket outlet on the same board complete all as specified and directed

All as per item Ser No 65 above but for one 15 amp socket outlet independent with 2 run of cable of size 4 sq mm and one run of 2.5 sq mm cable as earth continuity completed all as specified and directed.

Supply and fixing switch piano flush type single pole one way 5 Amp 240 volts completed all as specified and directed.

Supply and fixing for switch socket combination 2 in 1 , 5 pin 5 amps flush type 240 volts completed all as specified and directed.

Supply and fixing for switch socket combination multipurpose 15 amps flush type 5 in 1, 240 volts completed all as specified and directed.

S&F for ceiliing rose three terminal surface type bakelite 65x50 mm completed all as specified and directed.

Supply & fixing Surface and wall mounted LED batten 20 watt extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver with LED Lamp complete all as specified and directed. Make Havells ENDURALINEARNEOBS20WLED840SPCWH & equivalent make specified.

S&F security LED light fittings, 1x40W LED luminiaries Complete with all acessories and including connecting upwithtwin core twisted flexible copper conductor cable with suitable size of 230V, 50 HZ, 40mm light grade GI pipe with suitable clamps, nuts, bolts and all fitting accessories complete all as specified and directed.Make Havells Cat part No. ENDURAPEARLNEOSL40WLED757PASYTOPC & equivalent make specified.

S&F security LED light battern holder, 1x10W LED luminiaries Complete with all acessories and including connecting upwithtwin core twisted flexible copper conductor cable with suitable size of 230V, 50 HZ, and all fitting accessories complete all as specified and directed.Make Havells Cat part No.LED Adore Lamp 10W B22 WW & equivalent make specified.

S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for battern fittings.

S&F MCB distrubution board SPN 8 way double door, sheet steel,phosphatised,powder coated with 200 amps bus-bar,neutral link,earth bar and din rail 240 V complete all as specified and directed.( for living sheltor)

S & F MCB SPN 240V 40 Amps,10 KA complete all as specified and directed.

S & F only MCB SP, 240V,6 to 32 Amps,10 KA complete all as specified and directed.

S & F XLPE insulated heavy duty electric cables with Aluminium conductor, 1100 volts grade, cross sectional area 2corex10SQMM along the wall/Earth. Complete all as specified. 8

M & L for Sand filling under floors in foundations & in trenches including watering and consolidation. Complete all as specified and directed.

M & L for reinforced precast concrete cable cover, class LV Type 1, flat size 250mmx150mmx40mm. Complete all as specified and directed.

M & L for Tubes 'Light grade" galvanised 40mm for cable protection. Complete all as specified and directed.

M&L in replacement of circuit/submain wiring alongwith earth wire with the size of 2x4 Sqmm + 1x2.5 Sqmm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/recessed as required in and including PVC casing caping complete fixing on wall, roof and floor all as specified and directed.

Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground end vertically to a depth not less than 2.25 meter deep below ground level with top edge of the earth plate at a depth not less than 1.5 M below normal ground level connected to galvanized iron strip 32x6mm as earthing lead by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1, cover slab 54 cm x 54 cm x 5 cm, reinforced with 8 mm dia TMT bars @ 150 mm c/c both ways, one handle for lifting made out of 10 mm dia MS round bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing (light grade) for protection of earth lead connection, including necessary excavation and earth work in any type of soil, dismantling and taking out old earthing plate and necessary testing complete all as shown on electrical plate No 5 of SSR Part –I (2009).

M/S YESHI TSERING ENTERPRISES

M/S G M BUILDERS

M/S ACE BUILDERS

M/S K D CONSTRUCTION

M/S KESANG CONSTRUCTION

M/S L G BUILDERS

M/S P W ENTERPRISES