Rehabilitation of Bharatpur Feeder system District Bharatpur RWSLIP

Amount

Cutting and clearance of jungle,bushes,shrubs Ankra/Pomoea,Julicflora type etc. on canal and bunds in dry/moist/slushy conditions including disposal as per instruction of the Engineer-in -charge.Cost of wood has been deducted from rates and thus will be property of contractor after cutting .(For thick)

Cutting and uprooting of trees including removing of roots and filling of hole, cutting/up rooted would be property of the department (b)Over 15 cms to 30 cms. Girth

Earthwork in Excavation including loading, unloading, disposal and dressing of excavated earth within initial lead of 50m and lift up to 1.5m including dressing of excavated area, dewatering wherever required complete in all respect (b)Hard / dense soil

Earth work in rough ( borrow area ) excavation for embankments in hard soil, morrum of highly weathered strata dry of moist, including laying in 20 cm layers ( before compaction ) and breaking of clods, sorting of grass, pebbles etc. and dressing when compacted manually or by plain roller with intial lead of 250 m and lift ap to 1.5 m (Excluding charges for compaction and watering ) including loading and un-loading wherever required complete in all respect.

Compaction of earth or highly weathered strata (b)By mechanical equipment such as sheep foot roller/ pneumatic tyred roller/vibro compactor / vibro sheep foot compactor required as per site condition to obtain dry density of.(ii) at least 95% of Standard Proctor's density.

Watering of earth including cost of carriage of water when source of water is up to 1 km

Benching base and depositing the excavated material including dressing etc. Complete with in initial lead up to 50 M and fift up to 1.5 M

Lip cutting and final dressing as per designed section including rehandling and disposal of excavated earth in layer 20 cm on embankments etc. with cost of dewatering wherever required ,and complete in all respect.

Demolishing stone rubble masonry including stacking of useable material and disposal of unuseable material within 50 meters lead inclusive of de-watering wherever required. (b)In cement mortar

Preparation and dressing the sub grade including removal of irregularities up to 7.5 cm in soil, morrum mixed with pebbles, small boulders and and kankar & murrum for.

Side slope

Extra charges for water spray by nozzal on sub grade of canal including bed and side slopes before laying plain concrete for linning work.

Providing and laying cast in situ plain cement concrete design mix M-15 grade for lining, using well graded crusher broken aggregate of maximum nominal size 20 mm conforming to IS:383-1970, including proportioning of the ingredients by weigh batching and mixing by mechanical mixer including finishing of concrete lining, cutting of grooves for construction joints, complete as per specification with all leads and lifts of construction material complete for canal bed of thickness.In bed for 7.5 cm

Providing & laying canal lining with PCC blocks 50 mm thick made of cement concrete (1:2:4) grade M-15 with aggregate size up to 20 mm crusher broken including manufacturing of PCC block mechanically vibrated at site in size of 300x300x50 mm including all lead & lift s of material, tranportation of blocks from manufacturing stie to lining site, laid over 6 mm thick 1:3 cement mortar filling and smooth finishing of joint laid over 16 mm thick sandwich plaster in cement sand mortar 1:3 laid over 12 mm thick base plaster in cement 1:6 including curing and machinery charges with mixe rvibration etc. complecte as per technical specification.

Distance stone well dressed of required shape and size 60 cm x 23 cm x 7 cm with distance marked engraved and exposed faces well painted.

Fixing of distance stone in 30x30x30 cm pit excavated in all type of starta and back filling with cement concrete (1:4:8) projected 10 cm above ground level well finished and properly cured

Construction of puccca benchintervel mark muttam of size 30x30x75 cm in cement concrete (1:3:6 ) with maximum aggregate size of 40 mm with 75 cm long angle 25x25x5 mm embeded including curing transporation and fixing at site etc. complete with all lead & lift. At 500 m

Brick masonry (using well burnt clay bricks of size 230 x 110 x 70 mm, class designation 75 as per specification) up to plinth including all leads of all construction materials including curing etc. complete. (b)In cement sand mortar 1:4,

Brick masonry (using well burnt clay bricks of size 230 x 110 x 70 mm, class designation 75 as per specification) in superstructure including all leads of all construction materials including curing etc. complete in cement mortar 1:4.

Brick masonry (using well burnt clay bricks of size 230 x 110 x 70 mm, class designation 75 as per specification) in super structure including all leads of all construction materials including curing etc. complete. © In cement sand mortar 1:5 in super structure.

Half Brick masonry (using well burnt clay bricks of size 230 x 110 x 70 mm, class designation 75 as per specification) for partition wall including all leads of all construction materials including curing etc. complete. (b)In cement sand mortar 1:4

Providing and laying cement concrete coping in (1:2:4) with maximum size of crusher broken aggregate upto 20 mm including shuttering etc. with all leads of material complete in all respect in thickness of: 75 mm

Plaster in cement sand mortar 1:4 including racking of joints, smooth finishing & curing etc. complete including all leads of all construction materials of thickness 20mm thick.

Plaster in cement sand mortar 1:3 including racking of joints, smooth finishing & curing etc. complete including all leads of all construction materials of thickness 20mm thick.

Providing and laying under drainage below canal lining consisting of porous concrete of mix ratio1:4 ( 1 cement :4 course aggregate ) 75 mm diametre,300 mm long supported by 75 mm thick layer of course aggregate 12.5 to 40 mm size and 50 mm thic layer of sand

Providing & filling joints with sealing compound and coarse sand with bitumen of grade 85/25 (6% by weight) 4 cm depth

Side shuttering including propping etc. complete (toachievefinish F 2 for :Retaining wall, counterfort, abutment, wing walls up stream or down- stream slope facings of dams and open faces of construction joints etc..

Providing and Laying in position of Cement concrete Nominal mix (1:3:6) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. Well graded crusher broken stone aggregate of maximum size upto 40mm

Cement concrete (1:2:4) M-15 well mixed and laid in position complete including all leads of all construction materials including curing and finishing having well graded crusher broken stone aggregate of maximum size upto (d) 20mm

Cement concrete nominal mix (1:1.5:3) M-20 well mixed and laid in position complete including all leads of all construction materials including curing and finishing having well graded crusher broken stone aggregate of maximum size upto (d) 20mm

Extra labour charges for RCC due to obstruction in laying and placing the reinforced cement concrete due to reinforcement. (b)Columns, slabs, cantilevers projections staircases, lintels, beams, chajjas, Retaining walls, piers, abutments, galleries, arch covers, bed plates, sluice capstan bases etc.

Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix

Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor three level for Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands , coping, bed plates, anchor blocks, sills, chhajjas lintel, beam etc.

Supply of MS reinforcement including labour charges for bending binding and placing in position all reinforcement as per drawing including cost of binding wire and all leads and lifts using Tor or ribbed bars(IS 1786-1985)

Design, Drawing, fabrication, supply, erection, testing and commissioning of Vertical lift sliding type gate with frame consisting of skin plate, sealing frame, stiffeners, horizontal and vertical girders, guide, stainless steel flat/Brass flat, rivets, wedges, lifting rods etc., with all accessories as per relevant IS code including frame & gate complete set for Canal Cross, Escape, Head regulator /Tank head regulator including cost of all materials, machinery, labour, cutting, aligning, welding, finishing, cleaning, seal fixing, tools and tackles etc., applying two coat of zinc rich epoxy primer to give dry film thickness of 70±5 microns and finish coat (two coats) of solvent less coal tar epoxy paint using airless spray to provide dry film thickness of 150±5 microns per coat thus total dry film thickness of all coats, including primer coating, should not be less than 350 microns., complete as per specifications and approved drawings with all lead and lifts, including packing & forwarding, transportation charges for structural steel components and other materials.

Re-handing of excavated material including loading unloading and dressing within initial lead of 50 m and lift of 1.5m with cost of de-watering wherever required and all applicable taxes and levies etc. complete in all respect (a) Earth / Soil

Dismanting old plaster or skirting,racking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead,inclusive of de-watering wherever required.

Demolishing of reinforced concrete including stacking of useable material and disposal of unuseable material within 50 m lead inclusive of de-watering wherever required.

Demolishing brick work in ement mortar including stacking of useable material & disposal of unuseable material within 50 m lead inclusive of de-watering wherever required.

Random rubble stone masonry (using R. R. stones where 75 % stones to be not less than 15 cm in size in any direction and weighing not less than 23 kg.) for foundation including curing all leads of all construction materials including curing etc. complete. 2(c) In cement sand mortar 1:5

Flush or rulled pointing on stone masonry including racking of joints and curing etc complete including all leads of all construction materials in mortar ratio 1:3

Dry boulder filling in required profile with filling of voids etc. complete including all lead & lifts, and well finished surface

Providing and fixing 50mm thick cement concrete flooring with Metallic concrete hardener topping,under layer of 38 mm thick cement concrete 1:2:4 (1-cement:2-coarsesand:4-graded stone aggregate 20mm thick nominal size) and top layer of 12mm thick metallic concrete hardener consisting of mix 1:2 (1cement: 2 stone aggregate,6mm nominal size) by volume & mixed with metallic hardening compound of approved quality @ 2Kg./Sq m including cement slurry, rounding off edges etc.but excluding the cost of nosing of step etc complete.

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10 Cm. long embedded in cement concrete blocks 15x10x10 Cm. of 1:2:4 (1-Cement:2-coarse sand:4-graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Providing & fixing MS sheet single leaf door shutter in angle iron frame 35x35x5 mm suitabilly diagonally braced with 25x30 flat iron above and below lock rail of size 50x5 mm beading extra including all fittings,as per direction of Engg. incharge but excluding cost of chowkhats; including two coats of anti corrosive red oxide primer paint.(MS Sheet 20SWG.)

Supplying and fixing of steel windows made out (65x40mm) hollow metal pressed section of 1.25 mm thick sheet F4 & F7 standard rolled section confirming to IS 1038 with wholly openable shutter of 0.80mm thick(outside & Inside) opening C.R. sheets embossed panels, joint metred and flush, welded with suitable hinges, steel lugs and screws with approved oxidised steel handles,fittings peg stays(casement stays) etc complete in all respect including providing 10 mm square MS bars 10 cm C/C and applying priming coat of red oxide paint.

Providing and fixing angle iron frame 25x25x3 mm for ventilators with fixed wire gauge16 mesh 24 gauge incl.10mm square bars at interval of 100mm welded screwed to frame with metal beading 20x3 mm complete in all repect as per design.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding New work (two or more coats) over and including scrapping and priming coat with cement primer.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work.

Providing, laying and fixing in position RCC spun or hume pipe with collars (ISI 458-2003) in required size packed in gasket for hume or spun yarn & neatly finished with rich grout of cement mortar 1:3 perfectly air tight including testing of joints.NP-2

75 mm dia/80mm dia

100 mm dia

150 mm dia

225 mm dia

Making standard type cement gauge including engraving letters and painting including scaffolding etc.

Providing laying and fixing in position RCC spun or PVC pipe (4 Kg per Sq.cm. as per ISI 4985) with socket including all fittings in required packed perfectly air tight including testing 100 mm

Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar).

P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: size 530 x 410 mm

P & F WVC Foot- rest (IS : 2556 Mark) including cutting and making good the floor size: 250x125x25mm.

P & F WVC wash basin (1st quality, I.S. : 2556 Mark) of approved make with C.I. brackets duly painted, 1 No. 15 mm C.P. Pillar cock (IS : 8934 Mark) & 32 mm C.P. brass waste coupling of approved make, 25 mm G.I. waste pipe complete including cutting & making good the wall.: Size 450 mm x 300 mm

P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant.110 mm dia

P & F G.I. pipes (Internal Work) with G.I. Fittings excluding union (IS:1239 Mark) & MS clamps including cutting and making good the walls and floors: Exposed on wall B Class

(i) 15 mm dia nominal bore

(ii) 25 mm dia nominal bore

P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 1000 litre capacity

P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: Brass 400gm, 15 mm nominal bore

P & F Stop Cock (IS :8931 Mark), superior quality & of approved make: Brass 400 gm. 15 mm nominal bore

P & F Looking Mirrors with P.V.C. frame of approved (Atul, Modi Guard , Saint Gobin or equivalent) Size 500 x 400 mm

P & F Flush Cock / Flush Valve (IS : 9758 Mark) for WC of approved quality make : CP brass Half-turn exposed 25mm nominal bore.

Construction of Soakage well in all types of soil of approved drawing, top 90 Cm .Portion in 450mm thick masonry with CM 1:6, 80 mm thick stone slab covering, jointing of slab in CM 1:3 ,Ralthal, kharanja 40mm thick M-15 grade C.C flooring, earth work etc . complete including disposal of surplus earth within a lead of 50 mtr . Inner dia 90 Cm & 10 to 12 Mtr deep

Wiring of light point / fan point / exhaust fan point / call bell point with 1.5 sq. mm FR PVC insulated unsheathed 1.1kV grade flexible copper conductor and 1.5 sq.mm FR PVC insulated copper earth conductor (IS:694) of approved make in double lock/ ISI marked single lock pvc casing capping & it's accessories, 18 SWG M.S. box with earth terminal, screwless cage connectors for neutral looping in switch board & falce ceiling point, 6 A switch 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers , making connections, testing etc. as required.

(i) Short point (up to 3 mtr.)

(ii) Medium point (up to 6 mtr.)

(iii) Long point (up to 10 mtr..)

Wiring of 3 pin 6 amp. Light plug point with 1.5 sq. mm FR PVC insulated unsheathed 1.1 kV grade flexible copper conductor and 1.0 sq.mm FR PVC insulated unsheathed 1.1 kV grade copper earth conductor (IS:694) of approved make double lock/ ISI marked single lock pvc casing capping & it's accessories, 18 SWG M.S. box with earth terminal, screwless cage connectors for neutral looping in switch board & falce ceiling point, 6 A switch, 6 A socket, 3.0 mm thick phenolic laminated sheet, zinc plated / brass screws, cup washers, making connections, testing etc. as required.On board

S&F following sizes (dia.) of ISI marked medium duty PVC conduit along with accessories in surface / recessed using saddles, clamps, fastener as required including cutting the wall and making good the same as required.25 mm

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. 2x2.5 sq. mm +1 x 1.5 sq.mm

Supplying and fixing of power plug point accessories on 18 SWG metal box of size 175 x 100 x 60 mm. on surface or in recessed with suitable size phenolic laminated sheet cover including cost of 6 pin 16 amp. Switch and socket outlet , making connection , testing , etc. as required.

P&F 240/415 V MCB of breaking capacity not less than 10 KA (B/ C/ D tripping characteristic) ISI marked IS 8828(1996)]/ conforming to IEC 60898 in existing board/sheets including making connections with lugs, testing etc. as required.

(i) Single pole MCB - 6A to 32 A rating

(ii) Double pole MCB - 40 A to 63 A rating

P&F Recessed/ Surface mounting heavy duty horizontal type sheet steel Distribution board phophatised/ powder painted complete with copper bus bar, shorting link , neutral link, earth link and din bar, conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs , testing etc. as required.Double door (single phase) 12 Way

P & F ISI marked flush type 120/280 watt rotary step fan regulator including making connection testing etc. as required.

P & F double ball bearing capacitor start ceiling fan of approved make complete with regulator and other accessories as required. (for estimation purpose only) 1200 mm sweep

P & F strip type fluorscent tube fitting fabricated from (CRCA sheet and finished with powder coating / stove enamelled paint)/(extruded non corrosive UV resist EP channel) complete with accessories like (OCCB, starter, starter seat)/ EB, rotor holder, terminal block duly prewired with copper conductor including making connection, testing etc. as required. ( without tube) 1x36 Watts with OCCB

P & F Fluorscent tube rod in existing fixtures as required Flourscent powder coated (minimum 3 ster rating ) 36/40 Watts

P & F 1.6 mm thick M.S. Recessed fan box, hexagonal/ round of size 100 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side .

Plate Earthing as per IS:3043 with G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe including all accessories like nut, bolts, reducer ,nipple, wire meshed funnel, and C.C. finished chamber covered with hinged type with locking arrangement C.I. Cover, C.I. Frame of size300mm x 300mm complete with alternate layers of salt and coke/charcoal, testing of earth resistance as required.

P/Laying P.V.C. insulated & P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor of IS:1554 P-I of Group2 of approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand,IInd class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. 10.0 Sq.mm 4 core

Design, Drawing, fabrication, supply, erection, testing and commissioning of Adequate capacity manually operated screw type hoist according to relevant IS code, consisting of supporting structure, platform bridge etc., operating handle, gate position indicator, plumber block, couplings with all required accessories for operating Head/cross/ escape regulator gate including cost of all materials, machinery, labour, tools and tackeles, cutting, aligning, anchoring, welding, finishing, cleaning, greasing, oiling, applying two coats of zinc chromate red oxide primer and three coats of approved synthetic enamel paint etc., complete as per specifications and approved drawings with all lead and lifts, including packing & forwarding, transportation charges for structural steel components and other materials.

Design, Drawing, fabrication, supply, erection, testing and commissioning of Adequate capacity manually operated rope drum hoist according to relevant IS code, consisting of hoist platform bridge, rope drums, connecting shaft, gear system unit, pulleys, wire rope, Gate position indicator, manual operation system, etc. complete, with all accessories for operating gates including cost of all materials, machinery, labour, cutting, aligning, anchoring, welding, finishing, cleaning, greasing, oil filling, tools and tackles, applying two coats of zinc chromate red oxide primer and three coats of approved synthetic enamel paint etc., complete as per specifications and approved drawings, including packing & forwarding, transportation charges for all materials.

Providing Rubber seals as per IS:11855 for Dam sluice, canal, barrage, stop dam etc. gates of required size and type and specifications with testing, including all lead and lifts, packing & forwarding charges for all components etc. complete.(A)Rubber seal musical note type 75mmx33mm x12mm (33mm Bulb) uncladed

(B)Rubber seal musical note type 100mmx44mm x14mm (44mm Bulb) uncladed

Providing, Fabrication, machining with straightening work of Guide Tee, Track, Sealing frame, Leaf frame or any part of gate's, complete as per drawing with testing, including cost of all materials, with machinery, labour, tools and tackles cutting, aligning, welding, finishing, cleaning etc., applying one coat of zinc rich epoxy primer and two coats of cold applied coal tar epoxy paint, etc., complete as per specifications and approved drawings with all lead and lifts, including packing & forwarding, transportation charges for structural steel components and other materials.(A)Rate of work with all materials

providing and laying brick tiles of class designation 100 over mumty, roofs, grouted with cement motar 1:3 mixed with 2% of intigrated water proofing compound by weight of cement over 12mm thick layer of cement motar 1:3 and finished neat.

ARUN KUMAR CONTRACTOR