SPECIAL REPAIR TO 21 NOS MD ACCN IN KV-02 AT MIL STATION JAIPUR UNDER GE(S) JAIPUR

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/ brick surfaces/ceiling etc. including raking out joints hacking for key scrubbing down with water etc including removing outside MD land complete all as specified and directed.

M&L for rendering 15mm thick on stone masonry surfaces or surface other than fair faces of brick work on wall in CM (1:4) finished even and fair without using extra cement etc complete all as specified and directed.

M&L rendering 15mm on brick masonry surfaces or surface other than fair faces of brick work on wall CM thick (1:6) finished even and smooth without using extra cement etc complete all as specified and directed.

M&L for rendering 15mm thick on brick masonry surfaces or surface other than fair faces of brick work on ceiling CM (1:4) finished even and fair without using extra cement etc complete all as specified and directed.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint new plastered surfaces of wall, having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance interior acrylic emulsion paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of interior primer applied @ 0.90 litre/10 sqm over new surfaces over 1mm thick wall care putty on ceiling complete all as specified and directed by engineer in charge

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint new plastered surfaces of ceiling, having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance interior acrylic emulsion paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of interior primer applied @ 0.90 litre/10 sqm over new surfaces over 1mm thick wall care putty on walls complete all as specified and directed by engineer in charge

M&L for preparation of new plastered surfaces of wall and applying two coats of weather coat paint of approved shade over a coat of primer over and including 1mm thick wall care putty for smooth etc complete all as specified and directed.

Demolition Cement concrete (unreinforced) concrete of any description and in any position or otherwise specifically provided etc including removing outside MD land complete all as specified and directed.

Demolition/Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiling to store and rubbish off the premises etc including removing out of MD land complete all as specified and directed.

S&F joint free coloured glazed ceramic tiles in vertical surface 300x 450x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including providing 10mm thick backing coat in CM (1:4) etc complete all as specified and directed.

M&L joint free non skid ceramic tiles (coloured) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including providing 15mm thick screed bed in CM (1:4) etc complete all as specified and directed.

M&L non skid ceramic tiles (coloured) 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and using approved adhesive white or coloured cement to match the shade of tile including providing 10mm thick screed bed in CM (1:4) etc complete all as specified and directed.

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm etc complete all as specified and directed.

S&F in repair pillar taps 15mm bore swan neck, cast copper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed.

S&F wall mixer CP hot & cold, 15mm bore with L-bend connection to overhead shower, bright finish ,screwed the ends for iron pipe and plugging etc complete all as specified and directed.

S&F in repair CP brass towel rail 20mm dia, D type 60cm long etc complete all as specified & directed.

S&F in repair chromium plated shower roses 125mm size with swivel joints, any size, including shower arm 15mm bore size with bend of 45 degree with flange, etc complete all as specified & directed.

S & F in repair Chromium plated angle stop cock with wall flange fancy type cast copper alloy 15 mm bore any colour etc complete all as specified & directed.

S & F in repair Chromium plated stop cock with wall flange fancy type cast copper alloy 20 mm bore (Concealed type) any colour fixed etc complete all as specified & directed.

S&F in repairs Vitreous China wash hand basin, white, flat back, size 550x400mm but including brackets, coupling and waste pipe etc complete all as specified & directed.

S&F in repair Vitreous China Wash down water closet pan pedestal pattern (EWC) white in colour, and including plastic water closet seat, closed pattern with flat bottom and cover and MS chromium plated hinging device including connection to outgoing pipe and flushing pipe etc complete all as specified & directed.

S&F in repairs PVC valve less, syphonic action type flushing cistern 10 litres capacity, low level, white, with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC,32mm dia suitable for low level cistern etc complete all as specified & directed.

S&F of Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed dia of pipe 32 mm etc complete all as specified & directed.

S&F in repairs fancy type stop valves cast copper alloy chromium plated screwed down high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions in 15 mm bore dia pipe etc complete all as specified & directed.

S&F of CP pressure JET for EWC including flexible pipe for 15 mm dia bore etc complete all as specified & directed.

M&L PVC (SWR) floor trap, plain with grating including jointing with solvent cement fixed to 50mm bore of pipe including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 etc complete all as specified & directed.

S&F in repair for 15 mm GI tubing medium grade with all fitting and fixed to walls of concealed or fitted to ceiling or laid in under floor etc complete all as specified & directed.

S&F in repair for 20 mm GI tubing medium grade with all fitting and fixed to walls of concealed or fitted to ceiling or laid in under floor etc complete all as specified & directed.

S&F capacity of 1000 Litres rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of old water tanks etc complete all as specified & directed.

S&F ball brass valves, high pressure, with polythene float and fly-nut complete, screwed for iron pipe or brass ferrule and fixed of pipe in 20mm etc complete all as specified & directed.

M&L cement concrete (1:3:6) type C-2 using 20mm graded stone aggregates as in platform of rotational moulded polyethylene water storage tanks and dia of platform not less than 150mm etc complete all as per specified and directed.

Hacking out old broken glass any thickness size, quality or description from wooden/steel frames fixed with wooden beads/metal pinning and S&F 3 mm thick sheet glass in squares not exc 0.50 sqm in each pane fixed with wooden beads or putty (in metal frame) etc complete all as specified and directed.

S&F in repair vitreous china squatting pan 'Orissa' pattern water closet white size 580mm x 440mm with integral foot rest (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe anti-syphonage pipe etc complete all as specified and directed.

S&F in repairs soap dish vitreous china white approximate size 160 x 160 x 90mm fixed with chromium plated screws etc complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified & directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified & directed.

S&F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls etc complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls etc complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends (any radius) etc. complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends (any radius) etc complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction single, (single T) equal or unequal etc complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (single T), equal or unequal etc complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl etc complete all as specified and directed.

M&L PVC(SWR) floor trap/ nahani trap, plain with grating including jointing to waste pipe with solvent cement dia of outlet 75 mm etc complete all as specified and directed.

M&L PVC(SWR) Gully trap/ nahani trap, plain with grating including jointing to waste pipe with solvent cement dia of outlet 125/110 mm etc complete all as specified and directed.

S & F 250 mm Corner Glass shelf with brass brackets etc complete all as specified and directed.

S&F in repairs fancy type mild steel chromium plated caps/side bulbs PVC powder coated etc complete all as specified and directed.

S&F in repair drapery rod PVC insulated 20mm dia including providing and fixing brackets and decorative knobs on each end of rod of approved pattern and colour etc complete all as specified & directed.

S&F factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm Plain colour PVC sheet on back face in frame at site as per specification & drawing.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening etc complete all as specified and directed.

S & F 125x60mm Pressed steel frames 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S & F 105x60mm Pressed steel frames 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position etc complete all as specified and directed.

Cutting holes in stone walls built in cement mortar for inserting holdfasts and making good dismantled portion in CM (1:3) or in PCC (1:2:4) type B1 as required depth of embedded portion but not exceeding half brick etc complete all as specified and directed.

Supply and fixing 30 mm thick Fiber glass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.

S&F 35mm thick factory made second class hardwood glazed and skelton door shutter kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. The size of members of shutters shall be as specified in MES SSR Part-I Section 8, Clause 8.24(a). The shutter shall be fitted to chowkhats as directed by Engineer-in-Charge.

S&F in repair 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to angle iron chowkhat including welding etc complete all as specified and directed.

S&F in repair aluminium anodised tower bolts not less than 12mm dia of extruded section and fixed 150mm length of bolt etc complete all as specified and directed.

S&F in repair aluminium sliding door bolts 250mm long, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed etc complete all as specified and directed.

S & F in repair aluminium handles of size 125 mm anodised type complete all as specified & directed

S&F in repair 140mm long door stopper of aluminium anodised and two rubber shoes etc complete all as specified and directed.

S&F stainless steel cloth 0.50mm nominal dia of wire and 1.00mm average aperture and fixed with stain less steel wire staples etc complete all as specified and directed.

S&F in repair stainless steel cloth 0.50mm nominal dia of wire and 1.00mm average aperture and fixed with stain less steel wire staples etc complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer etc complete all as specified and directed.

Roof Treatment:- 1. Complete removal of the existing roof treatment and disposed of the rubbish outside MOD land. 2. All visible cracks to be opened up in V shape and remove all loose particles, cleaned properly with wire brushes and cracks are to be filled with crack filling compound for cracks upto 15 mm width/depth of cracks. 3. Cracks of more than 15mm depth are to be filled with cement grouting like (URP Cement grout) by injecting through nozzles till refusal by authorized applicators of manufacturer carefully by following manufacturer’s instructions. The size and spacing of the nozzles shall be all as per manufacturers instructions/as directed by Engineer-in-Charge. 4. After drying, roof coat paint shall be applied (@ rate of 1 L per 1sqm) with roller in both directions with a gap of 12 hr for each direction over a self prime coat @ 0.5 ltrs of water mixed to 1L of roof coat paint. 5. Necessary guarantee of 05 years shall be submitted by the contractor. Make:- Roof Coat:- Choksey chemicals ( Roof coat-3)/berger(PU roof coat)/ Asian (smart care damp proof ) Cement grout: - Dr Fixit (Fixit pidicrete URP Model:301) /or equivalant in Fosroc/ choksey chemicals/ sika

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in 15 mm thick screed bed cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed.

M&L 20mm thick screed bed or bedding layer in CM (1:6) for laying of floor finishes etc complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm etc complete all as specified and directed.

S&F Plate rack of size 900x750mmx300mm etc complete all as specified and directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm etc complete all as specified and as directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frame) not exceeding 1.5 sqm each and removing to store etc complete all as specified and as directed.

Taking down shutters of any description exceeding 1 sqm and not exceeding 2.00 each and removing site etc complete all as specified and directed.

M&L in repair 19 mm thick WPC membrane kitchen cabinet door shutter in wood grain colour, half round edge fixed etc complete all as specified and directed.

S & F Auto close hinges, stainless steel, bright finish or electro galvanised fixed in repair etc complete all as specified and directed. (Make:- Hettich or equivalent in)

M&L for 19mm thick WPC board in cabinet almirah cub board and partition of cabinet etc complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; barred iron doors ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc. complete all as per specified and directed.

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified & directed.

M&L for Brick work sub class B bricks straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:4) etc complete all as specified and directed.

Supply only Integral waterproofing compound

Demolition of reinforced cement concrete in roofs, floors (other than ground floors ), beams, staircases, landing, chajjas and similar suspended work including removing outside MD land complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) 1:2 :4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm th (Horizontal or sloping) Rough finished surface of concrete flat. etc complete all as specified & directed.

M&L 50mm thick cement concrete (1:3:6) type C-2 using 20mm graded stone aggregates as in plinth protection etc complete all as per specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons laid bedded and pointed in any mortar and removal of same from outside MOD land etc complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying Two coats of 100% Premium interior acrylic emulsion paint on plastered surfaces of Wall, having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance interior acrylic emulsion paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of interior primer applied @ 0.90 litre/10 sqm over new surfaces over 1mm thick wall care putty on ceiling complete all as specified and directed by engineer in charge

M&L for complete removal of existing treatment of ceiling and applying Two coats of 100% Premium interior acrylic emulsion paint on plastered surfaces of ceiling, having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance interior acrylic emulsion paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of interior primer applied @ 0.90 litre/10 sqm over new surfaces over 1mm thick wall care putty on ceiling complete all as specified and directed by engineer in charge

Demolition Cement concrete (unreinforced) concrete in ground floors and paving not exceeding 15 cm thickness (below or above ground level) etc including removing outside MD land complete all as specified and directed.

M&L 75 mm thick cement concrete (1:4:8) type D2 using 40mm graded aggregate as in sub base of flooring etc complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand etc complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required etc complete all as specified and directed.

Taking down carefully surface aluminium or copper point wiring with PVC casing capping or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces etc complete all as specified & directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 Sq mm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 Sq mm (Green) drawn into and including concealed rigid non-metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and unwelded sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulators as required for the following :- (Note - Cost of cutting of chases in stone masonry and making good disturbed surfaces for concealing the conduit shall deemed to be included in quoted rate of point wiring) complete all as specified and directed. (Note: Cost of hole cutting in wall for bell point, bulk head, building security light and any other site requirement during work execution shall be inclusive in above quoted price. Wiring on stone wall is included in above quoted price.)

(a) One light/Fan/Bell point controlled by one switch.

(b) One 3 pin 5 Amp socket outlet on the same board with other switches

(c) One 3 pin 5 Amp socket outlet on independent board with other switches

(d) One light point controlled by two, two way switches

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 Sq mm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 Sq mm (Green) drawn into and including concealed rigid non-metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets as required for 3 pin 15 amp socket outlet point controlled by one switch on independent board. (Note: Cost of hole cutting in wall for bell point, bulk head, building security light and any other site requirement during work execution shall be inclusive in above quoted price. Wiring on stone wall is included in above quoted price.)

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4.0 Sq mm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 Sq mm (Green) drawn into and including concealed rigid non-metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets as required for 3 Pin 15 amp socket outlet point controlled by one switch on independent board. (Note: Cost of hole cutting in wall for bell point, bulk head, building security light and any other site requirement during work execution shall be inclusive in above quoted price. Wiring on stone wall is included in above quoted price.)

S&F switch piano flush button single pole one way 5/6 Amp 230 volts etc. complete all as specified and directed.

S&F switch piano flush button single pole one way 15/16 Amp 230 volts etc. complete all as specified and directed.

S&F switch piano flush button Two Pole, two way 6 amp rating 230 volts etc. complete all as specified and directed.

S&F switch piano flush button Bell Push One way 5/6 Amp 230 volts etc. complete all as specified and directed.

S & F Socket Piano type 230/250 Volts 2 in 1, 3 pin 5/6 Amp ratings etc. complete all as specified and directed.

S & F Socket Piano type 230/250 Volts 2 in 1, 3 pin 15/16 Amp etc. complete all as specified and directed.

S & F in repair stepped type electronics fan regulator flush type AC 230 volts single pole (ISI marked) for AC 230V, 50 Hz on laminated sheet etc. complete all as specified and directed.

S&F in repair Ceiling rose surface bakelite 65x50mm, 3 Phase/ PVC/ Polycarbonate isolated body (ISI marked) etc. complete all as specified and directed.

S & F in repair lamp holder angle type PVC/Polycarbonate type with cord grip cap insulated body with back plate for pendant fitting including 9 Watt LED Lamp complete all as specified and directed

S & F in repair electric bell multi music type AC 230 volts single pole (ISI marked) for AC 230V, 50 Hz ding dong type etc complete all as specified & directed.

Supply & Fix surface mounted LED down lighter in power coated white finish with integrated electric driver, LED fittings 1X 12 Watt complete with all accessories prewired twin core twisted copper wire with suitable size etc complete all as specified & directed. Make: CG Cat Part No. LCRP-20 NW or Equivalent in Wipro/Philips.

Supply & fixing in repairs Energy saving environmental friendly, Trim Line LED Batten Tube Light fittings 18/20/22 Watt,1200mm(4 feet) TL, long life, impact proof, surface/wall mounting IP20,100 Lm per Watt, extruded Thermoplastic body with PC diffuser greater than 120 degree wide distribution available in 6500K CCT with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size complete including dismantling of old existing unserviceable fluorescent/LED TL & etc complete all as specified & directed. Make - CG cat Part No. LDL-20-CDL or equivalent in Wipro/Philips.

Supply & fixing in repairs Energy saving environmental friendly, LED Batten Tube Light fittings 10/12 Watt ,600mm(2 feet) TL, long life, impact proof, surface/wall mounting IP20,100 luminaire per Watt, extruded Thermoplastic body with PC diffuser greater than 120 degree wide distribution available in 6500K CCT with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size complete including dismantling of old existing unserviceable fluorescent/LED TL etc complete all as specified & directed. Make -CG cat Part No. LDL-10-CDL or equivalent model in Wipro/Philips.

Supply and Fix asthetically designed wall mounted synthetic non rechargeable comet wall mounted light (white) with B-22 base type lamp holder complete including 10 Watt LED Lamp and with all accessories prewired twin core twisted copper flexible copper conductor cable with suitable size etc complete all as specified & directed. Make: Philips cat part No. 30575 or equivalent model in Wipro/Philips.

Supply and Fix 10 Watt LED IP-65 Bulkhead environ friendly ultra modern energy saving surface mounted decorative hexagon bulkhead back lit LED luminaire comprising of high brightness LEDs wall mounted complete with all accessories prewired twin core flexible copper conductor of suitable size etc complete all as specified & directed. Make: CG cat Part No. LBHP-10-CDL or equivalent model in Wipro/Philips.

S&F in repairs Energy efficient LED security lights of 40 Wattage of IP 66 with PDC Aluminium body and clear glass, LED lens for wide beam distribution with efficacy greater than 100 Lm/watt , 5700K CCT, pf more than .90 etc complete all as specified & directed. Make - CG Cat Part No. LSTS-40-CDL M or Equivalent (Note: - Bracket along with screw to fix on wall/surface duly painted by silver colour shall be included in quoted rate.)

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 1100 volts grade, of size 25 sq mm. 4 core etc complete all as specified & directed.

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes, laying cables erection of poles / struts/stays etc not exceeding 10 Sqm on plan, not exceeding 1.5 metre in depth and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm in any type of soil complete all as specified and directed.

Removing of excavated material (soil) to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50metre above the starting point complete all as specified and directed

M&L for sand cushioning to PVC underground cable with tibba sand and punning to provide a required cover complete all as specified and directed. Note:- Punned thickness shall be considered for payment purpose

Supplying and laying un-reinforced precast cable covers class HV, type I, peak, size 300mm x 180mm x 40mm complete all as specified and directed.

Supply and fix 40 mm dia PVC rigid non metallic conduit welded exclusive of junction terminal boxes but inclusive of all fittings such as tees, bends, elbows, reducers, bell mount tube ends and all fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete for connecting wire of security lights fitting all as specified and directed.

Supply and fix 40mm dia steel tubing galvanised light grade for passing cable under road floors or fixing to poles for mechanical protection of underground cable complete with flat iron clamps made of shape and 12 mm dia bolts nuts and washers fixing where required complete all as specified and directed.

supply and fix TPN sheet steel power coated double door vertical distribution board 08 way fitted with two cover one screwed cover for incoming and outgoing MCBs and second for protection of MCBs fitted with colour coated Bus bar neutral link earth bar Din rail suitable for use of 240/415 Volts 50 Hz supply including on incoming MCCB 100 Amps Ratings 4 pole, MCB DP 63 Amps ratings 08 Nos., RCCB 01 Nos. and SP MCB of rating 06 to 25 Amps 20 Nos. etc complete all as specified and directed. Make: HPL cat Part No. DBVDD08163 or equivalent (Note: Cost of wall cutting for suitable mounting of DBs in recess along with proper connection with suitable lugs and making good disturbed surfaces with PCC work shall be included in quoted rate)

M&L for sub main wiring along with earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawn through surface casing and capping including 2x6 sqmm+1x4 sqmm PVC insulated multi stranded copper earth continuity conductor etc complete all as specified and directed. (Note: Cost of hole cutting in wall for any purpose site requirement will be deemed inclusive in above quoted price.)

S&F MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 42, IK-09 with reversible double door, recess mounted , having insulated 200 Amps tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required for the SPN, 240 volts, 8 ways etc complete all as specified and directed.

Supply and fix factory made sheet distribution board double door protection class IP-42 double door type suitable for mounting MCB/MCCB conforming to IS 13032 IS- 8623 and BS 5484 with minimum 200 Amps bus bar. DBs shall be fixed on wall in flush pattern by chase cutting in stone or brick wall and disturbed surfaces shall be made good even and smooth using PCC (1:2:4) for SP&N 12 Ways etc complete all as specified and directed.

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs etc complete all as specified and directed with following ratings:-

(a) SP 5 to 32 Amps rating

(b) SP 32 to 63 Amps rating

M&L earthing complete as per electrical plate No 3 of MES SSR Part-I with galvanised steel earth plate electrode 600 mmx600mmx6mm, buried directly vertically in ground in a pit depth not less than 2.25 metres below ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level connected to and including connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts check nuts and washers of galvanised iron or steel. Earthing strip shall be protected by galvanised iron or steel pipe 40 mm bore light grade and connected to continuous earth wire on pole / test point. Watering pipe shall be 20 mm bore GI medium grade. The earthing shall be of inclusive of excavation & earth work in any type of soil, charcoal, salt, funnel PCC pit and RCC cover etc complete all as specified and directed. NOTE:- (i) The concrete pit shall be made in PCC 1:2:4 type B-O, using 12.00 mm graded crushed stone aggregate 40mm thick precast cover slab of RCC (1:2:4), type B-1, using 20mm graded crushed stone aggregate with suitable MS handle in lieu of CI cover. Reinforcement in cover shall be of 8mm dia TMT bars laid @150mm c/c both ways. (ii) Quoted shall include the cost of 7.5 metre GI pipe for protection of earth wire/strip. (iii) Quoted shall include cost of 7.5 metre earth lead wire/strip. (iv) Earth electrode shall be surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides.

M & L for boring under road/drainage to pass GI pipe to protect under ground cable by automatic machine/manual etc.complete all as specified and directed.

Supply , installation testing and commissioning Indoor type LT cubical panel board suitable for 3 phase 4 wire 415 V 50Hz and power coated painting having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof & general construction confirming to IS 8623/93 comprising of the following- OUTER SHELL The shell shall be made out of 2 mm thick CRCA sheet, degree of protection for outer shell will be IP-54 & MS angles section 50x50x6 mm frame factory fabricated with front/back openable double door system lockable/openable from keys both sides having chromium plated19mm dia fancy locks, louvers air vents gaskets for natural air flow U type gasket will be used to make the outer shell completely vermin proof. The bottom of outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The Outer shell shall be powder coated with pure polyester Siemens grey structure RAL7032 shade. The outer shell dimensions shall be adequate to comprise inner shell complete with 75mm space all around and can be taken out when required without disturbing outer shell with a zinc metal coated stand having zinc coated not less than 100 microns

INNER SHELL- Inner shell shall be IP-42 Protection & made out of 2 mm thick CRCA sheet duly compartmentalized for each control gear front and back openable single door system lockable with keys from bottom side having chromium plated 19mm dia fancy lock 02 Nos. in each compartment having louvers and air vent gasket for natural airflow U type gasket shall be used to make inner shall completely vermin proof, TPN bus bar with colour coated on F class insulators made of non hygroscopic non combustible track resistance high strength FRP/SMC/DMC material at an interval not less than 500mm throughout the length of TPN bus bar. The cubical shall have a bottom channel of size 75x40mm duly coated with zinc metal coated having thickness not less than 100 microns. A detachable predrilled gland plate of thickness 3.15 mm powder coated should be used at bottom. The inner shell shall be powder coated Siemens grey structural RAL 7032 shade. including grouted in PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed and comprising following accessories:- Incoming:- (a) MCCB 100 Amps, 4 Pole, 25 KA, 415 volts, 50 Hz Thermally adjustable between 80-100%. - 01 No. Outgoing:- (b) MCB 63 Amps, DP, 10 KA, 240/415 volts, 50 Hz -05 Nos. (c ) MCB DP 40 Amps, 10 KA, 230 Volts, Double Pole, 50 Hz, C Characteristics-01 No

(d) TPN Bus bar of 150 Amps ratings with colour coded heat shrinkable sleeve (e) Digital Panel multi functional meter to measure current, voltage, frequency & power factor having programmable CT ratio. RYB Neon LED indicating lamp 01 set (f) Space for digital temper proof elect meter-04 Nos.

Schedule of Credit

UNIVERSAL INFRAPROJECT PVT LTD

M/S Anil Enterprises

J.J.ENGINEERING