C-O LWSS from GPS Dhangota natural source from Sub Division Barsar in Tehsil Barsar Distt. Hamirpur SH C-O Clear Water sump well 60700 liters. Pump House and Over head storage tank 25500 liters capacity with 15 mtrs staging height

Amount

Excavation in foundation , trenches etc., in all kinds of soil such as pickwork, jumper work blasting work, in soft / hard rock, including chiseling wedging out of rocks clearance of bushes etc.including shoring, dewatering etc. in all leads and lifts stacking the excavated soil upto any lead and lift clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth , sides of foundation etc. consolidating each deposited layers by ramming and watering and then disposing of all surplus earth within all leads and lifts complete to the entire satisfaction as directed by the Engineer-in-charge of the site of work.

Providing and Laying cement concrete1:3:6 (1Cement :3Sand:6 graded stone aggregate 20 mm nominal size) including curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4meters and removal of the same for insitu reinforced concrete and plain.

Foundations,footings bases of columns and the like and mass concrete complete in all respects in all leads and lifts

Vertical surfaces such as walls(any thickness) partitions and the like including attached pilasters, buttresses, plinth and string courses and the like complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like floors etc. above 200mm. In thickness with in all leads and lifts & to the entire satisfaction of the Engineer-in-charge

Beams,cantilevers,girders & lintels, sides & soffits of beams, haunching,cantilevers,bressumers 1.00 mts. In depth in all heights from floor in all leads and lifts.

Providing from work of ordinary timber plankings so as to give a rough finish including centring,shuttering, strutting and propping etc. height of propping and centring below supporting floor to ceililng not exceeding 4 metres and removal of the same for insitu reinforced concrete.

Arches beyond 6 metres span.

Random rubble stone masonry/polygonal rubble masonery ( uncoursed / brought to couses) with hard stone of approved quality in foundation & plinth including leveling up with cement concrete 1:6:12 ( 1cement :6sand : 12 graded stoene aggregate 20mm nominal size ) at plinth level in cement mortar 1:4 ( 1 cement :4 sand ) in all leads & lifts

Providing and Laying cement concrete1:6:12 (1Cement :6Sand:12 graded stone aggregate 40 mm nominal size) including curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Half brick masonery in common burnt clay building bricks in cement mortar 1:4( 1cement :4sand) 2nd class birck complete in all leads and lifts.

Providing and Laying cement concrete Design mix. M-30 not less than 1:1.5:3 nominal size (1Cement :1.5 Sand:3graded stone aggregate 20 mm nominal size) & curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :-

Foundations,footings bases of columns and the like and mass concrete in all leads and lifts.

Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses ,plinth and string courses etc. from top of foundation upto floor two level in all leads and lifts.

Providing and Laying cement concrete1:1.5:3 (1Cement :1.5 Sand:3graded stone aggregate 20 mm nominal size) & curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :-

Suspended floors,roofs,landing shelves and their supports balconies beams,girders bressumers and cantilever upto floor two level including carriage of material in all leads & lifts.

Arches upto floor two level

Brick work using common burnt clay building bricks (IInd class) in super structure above plinth level upto floor two level in cement mortar 1:6 (1cement:6 sand) in all leads and lifts.

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position with second class deodar wood in all leads and lifts.

Providing and fixing wood paneled glazed or paneled and glazed shutters for doors, windows and clear story 40mm thick windows including bright finished black enameled iron with necessary screws with second class deodar wood 40mm thick in all leads and lifts.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws with necessary screws 40mm thick with 2nd class Deodar wood in all leads and lifts.

20mm cement plaster in single coat of rough sides of bricks/concrete stone walls for interior plastering upto floor two level including arrises internal rounded angles chamber and rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6(1cement:6sand) within all leads and lifts.

6 mm cement plaster to ceiling in CM 1:3 (1Cement :3 Sand) in all leads and lifts.

15mm cement plaster in single coat of rough sides of bricks/concrete stone walls for interior plastering upto floor two level including arrises internal rounded angles chamber and rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:3(1cement:3sand) within all leads and lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1cement :3sand:6 graded stone aggregate 20mm nominal size) including finishing of the top surface of concrete smooth in all leads and lifts.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1 cement : 3 sand) with in all leads and lifts & to the entire satisfaction of the Engineer-in-charge.

Providing tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level including carriage of material in all leads & lifts.

Steel work welded in built up sections,trusses & framed work, including cutting ,hoisting & fixing in position & applying a priming coat of red lead paint :- In grating, framed ,guards,bars, ladders, railing, brackets & similar works in all leads and lifts..

Laying jointing and testting of GMS pipe following dia (medium/ light class) for scour pipe, inlet pipe , over flow pipe & distribution system including carriage of material in all leads & lifts.( Labour rates.)

80 mm dia .

Providing and fixing double flanged C.I sluice valve of following dia (with hand wheel) as per IS: 780 (including brass spindleand as per IS: 2906 Class-II complete with bolts., nuts, rubber insertion etc. ( along with tail pieces if required) following dia including all leads and lifts complete. ( Bir make) with M.S. flanges of table 5.

80 mm dia .

Distempering with dry distemper of approved brand and manufacture(Two coats) and of required shade on undecorated wall surface to given an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth. in all leads and lifts.

Providing and fixing SFRC Man hole cover with frame having frame size of 560mm internal dia (Medium duty) The Weight of cover & frame should not less than 100kg including carriage ofmaterial in all leads & lifts.

Constructing chamber for sluice valves with C.I surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab1:2:4(1cement:2sand: 4 graded stone aggregate 20mm nominal size ) 100mm thick foundation concrete 1:5:10(1cement:5sand:10 graded stone aggregate 40mm nominal size ) and insideplastering with cement mortar 1:3(1cement:3sand) finished with a floating coat of neat cement including curing complete with 600x600x750mm inside size with 150mm thick wall of RCC 1:2:4 ( 1cement :2sand :4 graded stone aggregate 20mm nominal size ) complete with form work and reinforcment with 6mm bars at not exceeding 150mm centres both ways in all leads and lifts and to the entire satisfaction of the Engineer-in-Charge.

Painting two coat (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt,dust and other foreign matter with Enamel paint other than white in all respects in all leads and lifts.

White washing with lime on undecorated walls surface (two coats) to give an even shade including thoroughly brooming the surface dirt dust mortar dirt and other foreign matter in all leads and lifts.

Finishing wall with water proofing cement paint of approved brand & manufacture & of required shade on undecorated wall surfaces (two coats) to give an even shade after thotoughly brushing the surface to remove all dirt & remains of loose powdered materials.

Providing and fixing M.S.fan clamp(Type-I of 16mm dial M.S. Bar bent to shape with hooked ends in RCC. Slab during laying including painting the exposed portion of loop all as per standard design complete in all leads and lifts.

Providing 40x3mm flat iron hold fast 40cm long including fixing to frame with 10mm dial meters bolts and nuts and wooden plug and embeding in cement mortar block 30x10x15cm 1:3:6(1cement:3sand:6 graded stone aggregate 20mm nominal size in all leads and lifts..

Providing and fixing following anodized aluminium fittings of anodized transparent and shade with necessary screw etc.complete in all leads and lifts.

Sliding door bolts 250x16mm.

Tower bolts (Barrel type) leads and lifts. 200x10mm.

Handles 125 mm dia

Providing and fixing M.S. grill of required pattern in wooden frames of windows etc. with M.S. flat square or rounded with round head nuts and bolts or by screwed complete in all leads and lifts.

Stone/Boulder filling under floors/behind retaining walls in all leads and lifts.

Providing and laying Precast terrazzo tiles hydraulic compressed 20 mm thick with marble chips of specified sizes laid in floors, treads of steps and landings on a bed of 25 mm average thickness of cement mortar 1:6 (1 cement :6 sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) incliding rubbing and polishing complete with tiles of complete in all respects in all leads and lifts

Construction of RCC over head tank 25500 litres with 15 metre staging height in M25 (Desigm Mix) from ground level to bottom of dome slab comprising of inlet,scour & over flow pipes as per deatails given below from G.L. to tank including bends of required degrees,valves of reqd.size conforming to relevants codes RCC Spiral 1.0 mtrs.wide stair case/MS stair case i/c GMS pipe railing as per IS specification,steel ladder 45 cms.wide of usual height as per site requirement M.S. manhole covers (Medium duty) 75xmx75cm fabricated with 3.15mm thick M.S sheet welded over M.S. angle iron frame of 40x40x6mm hinged on a frame of M.S. angle 50x50x6 properly grouted on the roof and having locking arrangement ventilator at Top done with minimum opening od 90x90cm. water level indicator including floats and measuring gauge, lightening conductor with earthing arrangement etc.The RCC over head reservoir shall include randering/plastering of the uneven expose surface, two coats of snowcem paint and any other component reqd.for the completion of the job to the entire satisfaction of Engineer-in-charge.The offers shall also include detail structural drawing / design calculations to be approved by the competent authority based on the raft foundation by taking seismic forces in the design calculation expension joints as required at site.The offer shall also i/c the cost of providing and fixing of GMS/MS pipes,and valve/fitting complete i/c duck foot bends,puddle collars,expansion joints etc.connecting with rising main & distribution main with reqd. length from the edge of foundation and any other components required for the completion of job upto the entire satsfactionof the Engineer-in-Charge.

kamlesh kumar

Rama Shankaer

BBN Enterprises