SPL REPAIR TO BLDG NO T-30, ADDN/ ALTN OF SEWAGE LINE AND PROVN OF ROOF SHEET, FALSE CEILING, TILING, FOOTPATH/ HARDSTANDING IN VARIOUS LOCATION AT RMS

Amount

Dismantling asbestos cement (Corrugated or semi corrugated) sheets in roof covering.

Dismantling wall and ceiling board fibre, pulp insulation etc or insulation boards any thickness including cover fillets complete all as specified .

Dismantling, floor, hearth or wall tiling including cement mortar bedding complete.

Demolition of reed lathing single or double including battens and plaster or chicken wire lathing.

Dismantling timber scantlings 40 sqcm and over in section, in unframed work any position.

Demolition of cement concrete in ground floors and pavings n.exc 15 cm thick above or below ground level.

Demolition of cement concrete in any description and any position not other wise specifically provided for cement concrete.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches etc complete

Taking down cement plaster on brick or stone nails, etc including raking out joints, hacking for key, scrubbing down with water etc.

Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters(Without taking off shutters from the frames).

All as per item 10 above but exceeding 1.5 Sqm but not exceeding 4 Sqm each

Taking down shutters of any description not exceeding 1 Sqm each.

Taking down shutters (ventilators) of any description not exceeding 1 Sqm each and refixing in same opening

Dismantling boarding of any description and fixed in any position fixed with nails or screws.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified

S&F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-Painted self embossed, textured designer board E-Board Classic to be fixed GI powder coated grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19x0.9 mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified.

S & F in repair for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed/laid /inserted to aluminium/GI grid/section and finally applying two coats of oil bound distemper complete all as specified.

S&F for post of Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) confirming Fe 410 -W (Gde- E- 250) quality- A

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165Fe-290 Grade-E-165 complete all as specified and directed at site.

Material and labour for non skid ceramic tiles 7-8 mm thick (square/rectangular) area of each tiles exceeding 0.18 sqm but not exc 0.38 sqm in floor etc set and jointed neat cement slurry and pointed in white in coloured cement to match over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per item No 22 hereinbefore but in skirting/dado including 10mm thick plastering for backing coat in cement mortar 1:4

S&F Non skid ceramic floor tiles of 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc with 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6), set and jointed in neat cement slurry and pointed in coloured cement

M&L for non - skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry over and including 15mm thick screed bed CM (1:6) and pointed in white or coloured cement to match complete all as specified and directed.

All as per item No 24 above here-in-before but in skirting over 10cm plaster in CM 1:4.

M&L for Glazed ceramic tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick CM (1:4) backing coat.

M&L for Glazed ceramic tiles in vertical surface300x200x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick CM (1:4) backing coat.

M&L for ceramic coloured printed tiles of size 300x200mmx7 mm thick, on verticals surfaces, set and jointed in neat cement slurry and pointed in coloured.

M&L for rendering 10 mm thick in CM 1:3 on fair faces of brick work or concrete surfaces to received vertical tiles.

M&L for rendering 15mm thick in CM 1:4 other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement.

M&L for Neeru finish to plastering as specified all as specified.

M&L for rendering 15 mm thick in CM 1:4 on one side of lathing finished even and smooth without using extra cement.

M&L for rendering 12 mm thick in CM 1:6 on other side of lathing finished even and smooth without using extra cement.

S & F 0.71 mm dia wire netting of galvanised steel wire of size 12 mm mesh fixed with tinned tack of wire staple.

M&L for brick work with sub class 'B' bricksstraight or curved on plan exc. 6.00m meanradius built in cement mortor 1:6.

Material and labour for brick work in cement mortar 1:4 with sub class `B' bricks straight or curved on plan exceeding 6m mean radius with old size bricks as in pillars complete all as specified.

Material & labour for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4.

M&L for PCC 1:4:8 (40mm graded aggregate) type D2 as in foundation

M&L for providing pre cast reinforced cement conccrete type B1,1:2:4 (20 mm grade Aggregate) in landings and similar articles with plane faces set in cement mortar 1:4 complete all as specified.

Precast RCC (1:2:4) type B-1 in manhole/soack well/septic tanks slabs/covers etc work complete set in cement mortar 1:6 complete.

M&L for RCC (nominal mix) Type B1 1:2:4 using 20mm graded stone aggreagate as in slabs.

M&L for PCC 1:2:4 type B-1(20mm grade stone aggregate) as in coping ,water troughsand the likes incl weathering slightly rounded and chamfered and throating etc complete all as specified and directed.

Extra for forming fair finished surfaces of drain or channels, inner girth 30 cms, using extra cement including forms, moulds mitred/ stopped ends etc., complete.

M&L 40 mm thk PCC 1:2:4 type B-1 using20mm graded agg as in flooring/pavements finished even and smooth using extra cement.

M&L for PCC 1:3:6 type C-2(40mm grade stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (40mm grade stone aggregate) as in bed to 150 mm dia SGSW /PVC pipes including packing under and haunching against the sides of pipes after they are laid and tested.

M & L cement concerte in surface channels and drains type C-2 1:3:6 using 20mm graded aggregate

Extra for forming fair finished surfaces of drain or channels, inner girth 30 cms, using extra cement including forms, moulds mitred/ stopped ends etc.

M & L for cement concrete 1:3:6 type C-2, 75 mm thick using 40mm graded stone aggregates as in plinth protection and sub base of floor finished fair and even.

M&L for second class hardwood as in scantlings clean sawn timber fixed.

Material & labour 2nd class hardwood plain, solid straight chowkhats and frames, wrought, framed rebated on the solid,rounded or chamfered, put together with glue pinned at joints, 2nd class HW.

S & F 35 mm thick flush shutters , solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S &F 2nd class hardwood 35mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauze etc divided into squares, with plain, chamfered or rounded mitred and rebated sash bars any number edges of framing plain, chamfered or rounded, fitted with cut and metered beads for securing glass etc size of members of shutters as specified in SSR Part I Sec 8 clause 8.23 (a)

S&F 2nd hardwood glazed and skeleton window and ventilator shutters, 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (b); supplied and fitted to chowkats. all as specified.

S & F second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps.

All as per item No 56 herein before but exc 6.00 and n.exc 13 Sqcm but bull nosed, splayed chamfered or rounded on one edge or face.

M & L for plain fillets, square, rectangular or triangular in section clean sawn, secured with nails 2nd class hard wood exc 13 and n.exc 25 sqcm.

S&F anodised aluminium frame for doors, windows, ventilators, grills, guard bars etc members made out of extruded Aluminium of any section and in any position including fixing Clips and provision of roller for fixing of prelaminated particle board , roller and roller plate for fixing of shower cubicals all as specified and directed.

S & F anodized aluminium window and ventilators shutters, sliding type without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing ,anodized aluminium snap beading, screws, anodised aluminium fittings complete all as specified.

M&L for sheet glass 3mm thick plain glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane.

S&F for sheet glass 4.0mm thick ordinary quality and glazing with oil putty in squares n exc 0.5 Sqm each pane complete all as specified.

S&F Sheet glass 4.8mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5sqm in each pane.

Suppy only stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed all as specified.

S&F in repair mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 18mm, fixed with tinned tacks or galvanized wire staples.

S&F floor door stopper overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening.

S&F for Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame wedded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site.

Fixing only framed work such as grills gratings etc with ends of bar shouldered/or riveted ,framed guard bars and similar frame work complete all as specified and directed at site.

S & F 100 size stainless steel butt hinges complete all as specified and directed

S & F 75 size stainless steel butt hinges complete all as specified and directed

Supply & Fixing 150 mm Aluminium handles, cast type, anodised

Supply & Fixing 125 mm Aluminium handles, cast type, anodised

Supply and fixing 100mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S & F 150 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed

S & F 200 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed

S & F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed

S&F in repair mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete

S&F 18/19mm thick pre laminated particle board, interior grades, prelaminated on sides with decorative choice laminated & other side balancing white lamination, fixed to screws to timber frame work and as dircted by Engr in Charge.

S & F 30mm width Continuous (piano) hinges, mild steel, bright finish or electrogalvanised

Supply and fixing 100mm size hasp and staple brass bright finish mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and as directed

Supply and fixing 40mm brass polished cupboard knobs fixed with nut screw and washer complete all as specified and as directed.

Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store.

All as per item No 83 hereinbefore but 20mm dia .

S&F in repairs 15mm bore GI water tubing medium grade laid in floors or fixed in wall including GI fittings.

S&F in repairs 20 mm bore GI water tubing medium grade laid in floors or fixed in wall including GI fittings.

Refixing 15mm dia old GI tubing and connection in new or old position (wall ceiling floor etc including cutting altering the size or changing the new fittings etc complete all as specified .

All as per item No 87 hereinbefore but 20mm dia.

Supply and fixing in repairs vitreous china squatting pan water closet,Orrisa pattern of size 580mmx440mm white with integral foot rests excluding flushing cistertn and flush pipe.

S&F in repairs10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and handle complete all as specified .

S&F vitrious china urinal, half stall type white complete including providing and fixing plugs,bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixding automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe, CP waste coupling complete.

S&F WHB vitreous china flat back or angle back type any size, including cutting for and pinning in ends of brackets or erecting stand PVC wash pipe and PVC connection PVC 32mm dia bore waste cuppling complete.

S&F pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shqanks and flynuts, screwed for iron pipe 15mm dia complete all as specified.

S&F for brass chromium plated shower rose with swivel joints, etc

M & L for bib cock CP with wall flange, fancy type 15 mm dia bore.

M & L for angular stop cock CP with wall flange, fancy type 15 mm bore dia.

M & L for concealed stop cock CP with wall flange, fancy type 15 mm bore dia.

S&F grating down 125mm dia with waste hole of PTMT (Min wt 40 gms).

S&F 600mm long tubular towel rail brass chromium plated 20mm dia, D type 60cm longfixedwith two plugs (Gutties) of 2nd class hard woodembeded in cement mortor 1:3 with MS screwscomplete all as specified.

Suuply & fix 150mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, laid in trenches or in floors and jointed as specified.

Suuply & fix 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, fixed to walls and in floors as specified.

S&F PVC (SWR) 75mm dia single socketed in any length with rubber ring joints laid in trenches or in floor.

S&F PVC (SWR) 110mm dia bends in any radius.

S&F PVC (SWR) 75mm dia bend.

S&F PVC (SWR) 110mm dia junction single T equal or unequal

S&F PVC (SWR) 75mm dia vent cowl

M&L for preparation of new wooden fillets surfaces and wood based surfaces of any description not exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pint wood primer. in tint as directed.

M&L for preparation of old painted wood and wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint in any tint all as specified and directed

All as per item No 109 here in before but applying two coats of synthetic enamel paint over a coat of pink wood primer on new surfaces

M&L for preparation of new painted surfaces of steel and iron work of any description over 10 cmwidth or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of redoxide on new surfaces in any tint complete all as specified.

All as per item No 93 hereinbefore but applying one coat on old surfaces

M&L for distempering walls with two coats of washable distemper oil emulsion on new surfaes(white or tinted) as directed after washing/rubbing down and stopping of distempered and painted surfaces as in preparatory work to give uniform and smooth finish all as specified.

All as per item No 113 herein before but applying one coats on old surfaces

All as per item No 113 herein before but applying one coats on old ceiling surfaces

Material and labour for preparation of new external surfaces of walls including cornices, plasters etc (Plastered or un plastered surfaces) and applying two coats of cement paint over one coat of primer complete all as per manufacture instructions all as specified and as diredted by Engineer-in-Charge .

All as per item No 116 hereinbefore but applying one coat on old surfaces

M&L for preparing surface of wood and wood based matreials, new or old, of any description and girth and treaed with tar or coal tar black paint and sanding newly tarred surfaces with clean sharp sand.

M&L for Preparing surfaces of wood and wood based materials,new or old, of any description and girth, not otherwise described and treated with one coat of creosote

Demolition and breaking up drain pipe (SWG or AC) 150 mm dia set in cement mortar and removal of debris to distance n.exc. 50 m and disposed off at site all as directed.

Demolition of damaged RCC cover slab of any description as in septic tank, soak well, manhole and gully trap etc (including separating of reinforcement) and removal of debris to a distance n.exc. 50 mtrs and spreading all as directed.

Excavating in trenches not exceeding 1.5mwide and n. exc 1.5m in depth; for foundation, etc not exceeding 10sq.m on plan and not exceeding 1.5m in depth and getting out in soft/ loose soil all as specified.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point, in soils.

Returning filling in sof/loose soil incl. spreading levelling watering and well ramming in layer n.exc. 25 cm thick.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape reqired including cranking, bending spirally for hooping ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to TMT bars

TMT Steel bars 6 to 8mm dia, cut to length bent to shape required including cranking bending spirally or hopping for columns hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

M & L screed bed and bedding layer of 15mm thick in CM (1:6) for laying floor tiles etc complete all as specified and directed.

M&L for 15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor.

M&L for Virified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tilesnot exceeding 0.36sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for Chequered cement concrete tiles 25mm thick, set, jointed and pointed in neat cement slurry with white cement and pigment as in floors

M&L for chequered cement concrete tiles 300x300x25mm thick with grey cement pigment over 15mm thick screed bed or bedding layer of mortar for laying floor finishes in cement mortar 1:6 over PCC 1:3:6 type C2 (40mm graded stone agg) 75mm thick as in sub base etc, set, jointed and pointed in neat cement slurry with grey cement and pigments, edges chamfered with cement concrete complete all as specified and directed.

M&L for anti fungal chequered cement concrete tiles 25mm thick with 15mm thick screed bed or bedding layer of mortar for laying floor finishes in cement mortar 1:6, etc, set, jointed and pointed in neat cement slurry with grey cement and pigments complete all as specified and directed.

M&L for Machine pressed precast conctete interlocking paver block any shape , size and colourconfirming to IS 15658-2006 of 80 mm thickness, M-40 Grade laid, jointed with grey cement and no pigment complete all as specified including preperation of formation bed over 25 mm thick sand cusion and pointed in colour cement mortar 1:3

M&L for Carrying out manhole covers/gully traps of any type and any depth removing the sludge/solid content from the manhole/gully trap by mechanical method and also cleaning the sewage line of any dia and at any depth either by water pressure or by any other flushing or roding and other suitable means at the discretion of the contractor at his own arrangements so as to remove the blockage and making the sewer lines and manhole/gully trap fully functional to the entire satisfaction of Engineer-in-Charge also to remove the sludge/solid contents out of defence land including covering with a layer of earth and repositioning of the RCC/CI cover slab all as directed by the Engineer-in-Charge.

M&L for Desilting of septic tank/soakage pit of any size, type and any depth and removing the sludge/solid content from the septic tank/soakage pit by mechanical method or any other suitable means at the discretion of the contractor at his own arrangements and make the septic tank/soakage pit fully functional to the entire satisfaction of Engineer-in-Charge also to remove the sludge/solid contents out of defence land including covering with a layer of earth and repositioning of the RCC/CI cover slab all as directed by the Engineer-in-Charge.

S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed.

M&L for Solid PVC Wall Lining consisting of 5mm thick Plain or coloured with wood grains printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame all as specified and directed.

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed.

M&L for Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site and 50 mm deep complete all as specified and as directed.Make:- Richa/Finolex/Havells/RR Kabel Make of caping/casing & PVC boxes :- Prestoplast/Finolex/supreme

One light/Exhaust Fan point controlled by one, one way switch .

One 3 pin socket outlet 5 Amps on the same board with other switches.

One 3 pin socket outlet 5 Amps on the Independent board.

All as per item No-142 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.

M&L for Switch piano flush type single pole, one way 5A Make:- Anchor/Havells/Legrand

M&L for Socket outlet, 2 in 1, 3 pin 5A flush type Make:- Anchor/Havells/Legrand

M&L Switch socket combination 2 in 1, 5A/16A, 5 in 1 flush type Make:- Anchor/Havells/Legrand

M&L for stepped type electronic fan regulator 100 W socket size flush type on the existing phenolic laminated sheet etc.Make:- Anchor/Havells/Legrand

M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body complete all as specified and directed. Make:- Anchor/Havells/Legrand

Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of 4 Sq mm and one run of 4 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and as directed. NOTE:- two runs of 4 Sq mm + one run of 4Sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length .Make:- Richa/Finolex/Havells/RR Kabel Make of caping/casing :- Prestoplast/Finolex/supreme

M&L for 20W LED, 4', Wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver.etc with all accessories internally pre-wired and fixing the same on and including two Nos PVC blocks and connecting up with flexible copper cable of size 0.75 Sq mm 3 core from ceiling rose to the light fitting incl taking down old unsv light fitting complete all as specified and as directed. Make : Havells Cat No LHFXCEP1TNNW020(batten) & LHDLEFXD5LR020(LED Tube) or equivalent in Bajaj/Philips

M&L for Lamp holder , PVC/ Polycarbonate type with PVC round/square block incl 9 watt LED lamp suitable for lamp holder fittings incl taking down old unsv light fitting. Make oF Lamp holder:- Make:- Anchor/Havells/Legrand MakeOf Lamp :- Havells/Bajaj/Philips

M&L for LED 1x20W Security light fitting, drawn through including GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling holes as required and connecting up with flexible copper cable of suitable size from ceiling rose to the light fitting complete all as specified and directed. Make:-Havells Cat Pt No LHETBXU7PA6S020 or equivalent in Bajaj/Philips

Taking down Exh/Ceiling fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, painting of fans complete with superior quality synthetic enamel paint by spraying including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed.

M&L for rubber bush with clamping set, comprising GI bolt, nut and split pin complete all as specified and as directed.

M&L for replacemnt of capacitor 2.5 Mfd incl making electrical connection complete all as specified and as directed.

M&L for replacemnt of steel ball bearing/bush of suitable size compatible to the existing ceiling fan/Exhaust Fan complete all as specified and as directed.

M&L for copper rewinding for suitable size complete to the existing ceiling fan/Exhaust fan complete all as specified and as directed.

M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed. Make:- Legrand Cat No 507611 or equivalent in ABB/Siemens

M&L for MCB Distribution board double door type SPN 4 way, sheet steel, powder painted, with bus bar neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed. Make:- Legrand Cat No 507610 or equivalent in ABB/Siemens

M&L for MCB TPN 63 Amps, 415 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make : Legrand Cat No 408704 or equivalent in ABB/Siemens

M&L for MCB SPN 32 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make:- Legrand Cat No 408636 or equivalent in ABB/Siemens

M&L for MCB SP 5-40 Amps, 230 volts, 50 Hz suitable for fixing in MCB DB 'C' series incl taking down old unsv MCB complete all as specified and as directed. Make:- Legrand Cat No 408587-95 or equivalent in ABB/Siemens

Taking down LT UG cable/ service connection of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 25 sq mm, 3.5 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items.Make : Richa/Havells/Polycab

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth and getting out in soft/ loose soil complete all as specified ans as directed.

Returning filling in trenches including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all complete all as specified ans as directed.

Removing of excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all complete all as specified ans as directed.

M&L for spread fine river sand in trenches complete all as specified ans as directed. NOTE: For measurement purpose, punned down thickness shall only be taken.

M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed

Supply & laying tubes ' light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings for protection of cables of size 40 mm dia bore including taking out unsv GI tubing complete all as specified and as directed. Make:- Jindal/TATA/Prakash surya

M&L for earthing complete with galvanized steel earth plate electrode of size 600x600x6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia as earth lead connectd by means of bolts, nuts, washers and check nuts all as shown in electrical plate No 3 of MES SSR Part-I, including testing on completion complete all as specified and as directed. NOTE:- (i) The unit rate shall also included for earth work in hard/ dense soil, PCC (1:3:6) type C1 chamber, CI frame with CI cover funnel with GI watering pipe 20mm dia Medium grade, GI protection pipe light grade 15mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (notes) under sub heading earthing, specified on Sl Page No 389 of MES SSR Part-II. (ii) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.

TOSHIKA SUMI

das enterprises

SHRI MADAN SINGH

m/s chakraborty enterprises

M/S RAHUL TRADING CO.

commercial enterprises