REPAIR TO SEEPAGE TREATMENT SUNKEN FLOOR PLASTERING WORK AND MISC REPAIRS TO PERMT BLDGS IN NORTH CAMP AT AFS SAMBRA

Amount

Taking down cement plaster including racking out joint hacking for key scrubbing down with water etc.all as specified and directed

Demolition of cement concrete, un-reinforced, in ground floors and pavings not exc 15 cm thickness (below or above ground level) all as specified and directed

Demolition of cement concrete, un-reinforced, of any description and in any position all as specified and directed

Demolition of brickwork or stone/boulder masonary, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, all as specified and directed

M & L Pre cast cement concrete 1:3:6 type C1 using 20 mm graded stone agrregate as in solid block masonry exceeding 10cm in width having minimum compressive strength of 50 kg/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:6 complete all as specified

M & L for pre cast cement concrete 1:3:6 type C1 using 20 mm graded stone agrregate as in solid block masonry not exceeding 10cm in width having minimum compressive strength of 50 kg/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:4 complete all as specified

M & L Preparation of floor and wall surfaces, treatment and sealing of all joints, corners, junctions of pipes and Masonry with polymer mixed slurry and as directed.

Material and labour for applying first layer of cement slurry at 0.488 kg/ sqm mixed with Acrylic based polymer 'ARMOUR -CRETE' of structural water proofing pvt ltd by ratio 1:2 (one Armour Crete : Two cement) or 'POLYCRYL' of Green boro polychem pvt ltd by ratio 1:2 (one polycryl : Two cement) or Ready to use PIDIFIN 2k of PIDILITE INDUSTRIES or SHALICRETE-500 of capital steel and chemicals pvt ltd and silica sand by ratio 1:2:2 (Shalicrete : Cement : Silica Sand) or NAFUFILL BB2 of MC Bauchemic India Pvt Ltd (ready to use) at 0.126 kg/sqm as per manufacturers instructions. This layer will be allowed to Air Cure for 4 hours and as directed

M&L applying second layer of 1.5mm to 2.0mm thick slurry of cement at 0.242kg/sqm mixed with acrylic based polymer 'ARMOUR CRETE' of structural water proofing pvt ltd and silica sand by ratio 1:2:2 (Armour -crete : cement : silica sand) or 'POLYCRYL' of Green boro polychem pvt ltd and silica sand by ratio 1:2:2 (Polycryl : cement : silica sand) or ready to use PIDIFIN 2k of PIDILITE INDUSTRIES or SHALICRETE-500 of capital steel and chemicals pvt ltd and silica sand by ratio 1:2:2 (Shalicrete : Cement : Silica Sand) or NAFUFILL BB2 of MC Bauchemic India Pvt Ltd (ready to use) at 0.126 kg/sqm as per manufacturers instructions. This layer will be allowed to Air Cure for 4 hours followed by water curing of 48 hours and as directed.

M & L PCC 1:5:10 type E-2 using 40 mm graded stone aggregate as in lean concrete in sunken portion all as specified and as directed.

Material and labour in padding of 40 mm thick in cement concrete type B1, 1:2:4 (20 mm graded aggregate) as in roof all as specified and directed.

M & L rendering 10 mm thick cement mortar 1:3 mixed with (conplast-X 42 11 C fosroc chemical (India) Ltd) water proofing compound 100 ML per bag of cement as specified by manufacturer instruction on concrete surfaces of roof and making the surfaces finished fair and even as required slope for draining out the rain water all as specified and directed. Note - WPC conplast-X 42 11 C fosroc chemical (India) Ltd shall be measured and paid separately

M & L Preparing RCC roof slab by removing dust, dirt and applying oil bond bituminous primer @ 0.2Kg/Sqm and providing 4 mm thick APP modified water proofing membrane weighting not less than 3 Kg/Sqm reinforced with non woven polyester matt weighing not less than 150 gms/sqm including minimum 10cm side over laps and 15cm end lap torch sealed and bonded and applying a coat of blown hot bitumen 95/15 over a membrane at 1.20 kgs/sqm all as per detailed specification and procedure all as specified and as directed.

Apply a coat of solar reflective bituminous aluminium paint over APP membrane on roof top surfaces at 0.10 kg/sqm all as specified and as directed.

Cleaning the existing ceiling surface of concrete and exposed reinforcements by wire brush including scrapping & cleaning with emery paper and washing down with water as required and applying “Epoxy zinc primer over a coat of Solvent free epoxy concrete bonding agent” as per manufacturer’s instructions on old concrete surfaces for bonding with new plastering complete with necessary scaffoldings all as specified and as directed. Note : Epoxy primer and bonding agents are measured seperately.

S & F welded steel fabric not exc 4kg/sqm complete welded with existing steel reinforcement elements all as specified and as directed.

Supply only epoxy zinc rich primer all as specified and as directed. Make : Nitozinc primer of FOSROC/Friazinc R of SIKA/ or equivalent in PIDILITE

Supply only Solvant free Epoxy concrete bonding agent. Make : Nitobond EP of FOSROC/Carbodur of SIKA/ or equivalent in PIDILITE

S & F Galvanised Iron wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste all as specified and as directed.

Dismantling wall floor hearth tiling including cement mortar bedding (but not backing) and removing unserviceable material all as specified and as directed.

M & L Plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in 25mm thick levelling sub base to floor all as specified and as directed.

M & L Coloured glazed ceramic tiles in vertical surface 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10 mm thick backing coat cement mortar 1:4 complete all as specified and directed.

M & L Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles over cement screed 15 mm thick cement mortar 1:6 complete all as specified and directed.

M & L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) double charged, polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with rectified edges ( joint free) etc set and jointed in neat cement slury over screed bed 15 mm thick cement mortar 1:6 complete all as specified and directed.

M & L Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab ncluding rubbing and polishing complete all as specified and directed.

M & L Granite tiles 16-18mm thick (of any type) work (table rubbed and polished) in cooking, steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situation upto 20mm thick all as specified and directed.

Taking down 25 or 32 mm bore steel/PVC tubing including fitting i.e elbow, sockets etc all as specified and directed.

Taking down 20 mm bore steel/PVC tubing including fitting i.e elbow, sockets etc all as specified and directed.

Taking down 15 mm bore steel/PVC tubing including fitting i.e elbow, sockets etc all as specified and directed.

Dismantling water tanks of capacity exc 1000 ltrs and not exc 2000 ltrs all as specified and directed.

M & L Cutting chases on stone walls /concrete slab etc, pinning in, making good to facings where required and pointing in cement mortar 1:3 to cutting chases for concealed water tubing etc. and making good exc 20 mm girth all as specified and directed.

Supplying and laying CPVC pipes SDR 11 nominal size 15mm confirming to IS-15778 as per ASTM D 2846 including plain & CPVC brass threaded special fittings CPVC SDR 11 fittings or of reducer or enlarged bore dia fixed to walls/ceiling or laying in floors including necessary cutting/chasesing in wall/floor of any description and their making good all as specified and directed.

Supplying and laying CPVC pipes SDR 11 nominal size 20mm confirming to IS-15778 as per ASTM D 2846 including plain & CPVC brass threaded special fittings CPVC SDR 11 fittings or of reducer or enlarged bore dia fixed to walls/ceiling or laying in floors including necessary cutting/chasesing in wall/floor of any description and their making good all as specified and directed.

Supplying and laying CPVC pipes SDR 11 nominal size 25mm confirming to IS-15778 as per ASTM D 2846 including plain & CPVC brass threaded special fittings CPVC SDR 11 fittings or of reducer or enlarged bore dia fixed to walls/ceiling or laying in floors and their making good all as specified and directed.

S & F Unplasticised PVC pipes 40mm dia of pressure rating 10 kgf/sq cm fixed complete to walls, ceilings or in floors etc., any type of pipe including fitting such as bends,elbows, unions, tees, reducing tees, adopters, sockets, plugs, hose clips, brass fittings etc complete all as specified and directed.

S & F in repairs flush pipe 32mm dia of polythelene of low or high density for low level flushing cistern complete all as specified and as directed.

Supply and fix in repairs vitreous china wash down water closet pan pedestal pattern white (excluding flushing cistern) including following accessoreis all as specified & directed :- (i) Plastic water closet seat cover, black or white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device (ii) (II) Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook

Supply and fix in repairs vitreous china squatting pan Orissa pattern of size 580 x 440 mm white with integral foot rest (excluding flushing cistern) including provn of lime concrete bedding etc complete all as specified & directed

Supply & Fixed in repair PVC valve less syphonic action type low level flushing cistern 10 Ltr capacity including flange valve handle, Bracket, PVC flush down pipe length upto 1.3 m height, dia as required with bend all as specified & directed

S & F in repairs Vitrious china wash basin, white flat back size 550X400mm including, waste coupling , pipe and cutting for and pinning in ends of brackets or erecting stand brackets all as specified & directed

Supply and fix rotational moulded polyethylene water storage tank 500 liters capacity (cylindrical vertical with closed top) double layered, hoisted and fixed in position including taking down old unserviceable tank all as specified and directed

Supply and fix rotational moulded polyethylene water storage tank 1000 liters capacity (cylindrical vertical with closed top) double layered, hoisted and fixed in position including taking down old unserviceable tank all as specified and directed

Supply and fix rotational moulded polyethylene water storage tanks of 2000 ltrs capacity (cylindrical vertical with closed top) double layered hoiseted and fixed in position all as specified in SSR Part-I including ball valve high pressure of PTMT coated aluminium rod and high density plastic ball screwed for iron pipe and fixed of 40 mm dia (minimum weight 690gms) complete all as specified and directed.

Disconneting existing tanks of capacity exc 500 ltrs to 1000 ltrs, setting aside (or lowering if required) for cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc. and reconnecting and re fixing in position after necessary cleaning.

Disconneting existing tanks of capacity 1000 ltrs to 2000 ltrs, setting aside (or lowering if required) for cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc. and reconnecting and re fixing in position after necessary cleaning all as specified and directed.

Supply and fix in repairs gun metal gate valve suitable for 25mm dia pipe, iron wheel head, screwed both ends complete all as specified and directed.

Supply and fix in repairs gun metal gate valve suitable for 40mm dia pipe, iron wheel head, screwed both ends complete all as specified and directed.

Supply and fix in repair Bib taps fancy type, chromium plated brass round handle, screwed down, screwed for iron pipe 15mm dia complete all as specified and directed.

Supply and fix in repair Stop valves fancy type, chromium plated, screwed down, high pressure, with crutch or round handle screwed bolts ends for iron pipe 15mm dia or for unions complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar of size 100 mm/ 75 mm all as specified and directed.

S&F PVC (SWR) pipes 75 mm dia, single socketed in any length with rubber ring joints, fixed in wall/ floor with necessary clamping where required all as specified and directed.

S&F PVC (SWR) pipes 110 mm dia, single socketed in any length with rubber ring joints, fixed in wall/ floor with necessary clamping where required all as specified and directed.

S & F in repair (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm dia outlet inclduing fixing to existing pipe properly with solvent all as specified and directed

S & F PVC (SWR) bends for 75 mm bore pipe with access door all as specified and directed

Supply and fix PVC SWR 75 mm dia branch pipe, singe (Single Y) equal or unequal provided with access door all as specified and directed

Supply and fix PVC plain bends for 75 mm bore pipe all as specified and directed

S & F (SWR) floor trap, plain with grating including jointing with solvent cement 110 mm dia outlet inclduing fixing to existing pipe properly with solvent all as specified and directed

S & F PVC (SWR) bends for 110 mm bore pipe with access door all as specified and directed

Supply and fix PVC SWR 110 mm dia branch pipe, Double (double Y) equal or unequal provided with access door all as specified and directed

Supply and fix PVC bends for 110 mm bore pipe all as specified and directed

S & F PVC (SWR) vent cowl 110 mm dia all as specified and directed

Dismantling of wrought iron or mild steel work of any description like wind ties / purlins and rafters all as specified and directed

Dismantling asbestos cement (Corrugated, semi corrugated, etc) sheets in roof coverings including ridges all as specified and directed

Dismantling RCC posts or struts ( steel , RCC) any section including taking down embedded portion and making good disturbed ground all as specified

M & L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete all as specified and as directed

Supply and fixing Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc of Fe 290 (Gde E-165) complete all as specified and directed.

S & F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws all as specified and directed.

M & L rendering over concrete/ brick wall surfaces 10 mm thick cement mortar 1:6 finished even & smooth all as specified and directed.

M & L rendering over concrete/ brick wall surfaces 15 mm thick cement mortar 1:4 ffinished even & smooth all as specified and directed.

M & L rendering over concrete ceiling surfaces 5 mm thick cement mortar 1:3 ffinished even & smooth all as specified and directed.

Supply only liquid water proofing compound

Material & Labour for applying Two coats of acrylic emulsion paint of Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied on new plastered surfaces of walls complete as mentioned in SSR all as specified and as directed .

Material & Labour preparing, washing, rubbingdown and complete removal of existing treatment for applying Two coats of acrylic emulsion paint of Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied on Old decorated surfaces of walls complete as mentioned in SSR all as specified and as directed .

M & L preparation of newly plastered wall surfaces and applying two coat of oil bound distemper over 3mm thick layer of putty finished smooth all as specified and directed

M & L Complete removal of existing treatment of old treated wall surface, perpration of surface and applying two coat of oil bound distemper over 3mm thick layer of putty all as specified and directed

M & L Preparation of newly plastered wall surfaces and applying three coats of white wash all as specified and directed

M & L Preparation of old plastered wall surfaces and applying two coats of white wash complete all as specified.

M & L Preparation of newly plastered ceiling surfaces and applying two coats of white wash all as specified and directed

M & L Preparation of old plastered ceiling surfaces and applying two coats of white wash all as specified and directed

M & L Preparation of old painted wood and wood based surfaces over 10 cm width or girth of any description, not otherwise described, and applying one coat of Synthetic enamel paint (Ordinary tint) all as specified and directed.

M & L Preparation of new steel surface exc 10cm width or girth and applying two coats of synthetic enemal paint over a coat of red oxide primer all as specified and directed.

Material and labour aluminium sheeting 0.56 mm thick in crumple portion all as specified and directed.

M & L High density polyethylene pipes (HDPE) 40mm dia of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. all as specified and directed.

Demolition of reinforced cement concrete, in suspended slabs, beams, lintels, etc in cement mortar or cement concrete (reinforcement cut out as required to facilitate demolition) all as specified and directed.

M & L mild steel TMT bars of 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L mild steel TMT bars of 6mm to 8mm, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L Formwork to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick for fair finished flat surfaces (horizontal or slopping) at first floor roof projection all as specified and directed.

M & L reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) all as specified and directed.

S & F Solid PVC Door frame of size 50mm X 47mm made out of 5mm plain color PVC sheet reinforced with MS square tube all as specified and directed.

S & F factory made solid pane PVC moulded door shutter 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face and 2 mm thick plain colour PVC sheet on back face as per specification with particle board core all as specified and directed.

S & F Aluminium anodised barrel tower bolt 100 mm long all as specified and directed.

S & F Aluminium anodised handle cast type 150 mm all as specified and directed.

S&F Stainless steel butt hinges 100 mm all as specified and directed.

Supply and fix in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws all as specified

S & F in repairs Alumimium Hat pegs, solid body, 125mm to 175 mm in length all as specified and directed.

Refixing of shutters of any description (wooden, aluminium, mild steel) in same opening of any description exc 1 Sqm but not exceeding 2 sqm, including taking down, easing and adjustingand also refixing builders hardware as required including renewal of unserviceable screws etc complete all as specified

M & L Plain Cement Concrete 1:4:8, type D2 using 40mm graded stone aggregate as in 75mm thick sub base to floor all as specified and directed.

M & L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, including demolition all as specified and directed.

M & L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with with pigment to match the shade of the slab including rubbing and polishing including backing coat 10 mm thick cement mortar 1:3 etc complete all as specified and directed.

M & L Mirror polishing on marble/ granite/Kota stone/ stone work where ever required to give high gloss finish all as specified and directed.

M & L PCC 1:3:6 type C1 using 20mm graded stone aggregate as in 75mm thick plinth protection and finished even and fair without using extra cement including cutting expansion joint and filling bitumen in joints all as specified and directed.

M & L Cement concrete 1:2:4 type B-1 20mm graded stone aggregate as in coping including necessary form work and surface of concrete shall be finished even and smooth without using extra cement all as specified and directed.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exc 1.5 m above the starting point all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.,) or insulation boards/slabs/blankets, any thickness including cover fillets and frame work complete all as specified and directed.

M & L Powder coated Aluminium snap grid frame work (size of grid 605 x 605mm) supported by hangers 4 mm dia G I (up to 1200mm length /as per site requirement) adjusting level fixed to roof slab/walls/wooden/steel members by means of ceiling cleats made out of GI flat 40x3mm size 60 cm long and expansion hold fasteners 12.5mm dia 40mm long with Gypsum board 12mm thick in ceiling as per manufacturer instruction including painting two coats of oil bound distemper over a coat of self primer and preparatory work complete all as specified & directed

M/s. N D KALING

RAJENDRA KRISHNA SARAF

PURVIK CONSTRUCTIONS

M/s B C CHOUGULE