ADDN/ALTN AND REPAIRS WITH ALLIED WORKS FOR OFFRS, JCOs, ORs Md ACCN AT UDHAMPUR (PH-I OF PH-II) UNDER GE (N) UDHAMPUR

Amount

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and its removal from site including making good all disturbed surface and finishing for reception of plugs and chowkhat, complete all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) area exc. 1.5 Sqm but n exc 4.0 sqm each and its removal from site including making good all disturbed surface and finishing for reception of plugs and chowkhat, complete all as specified.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified.

Factory made solid PVC Moulded door shutter, 28 to 30 mm thick (style), with 2, 4 or 6 raised panel design with 2mm thick Moulded PVC sheet on the front face and 2mm plain colour PVC Sheet on back face, supplying and fixing in frame at site as per specification & drawing consisting of frame made of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail, panelling of plain colour PVC sheets to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplied & fitted in the frame at site as per specification & drawings shown in SSR Part-II, complete as specified shade and colour as approved by GE/ Engr-in-Charge.

100mm long aluminium anodised butt hinges, type B-21 with galvanised mild steel screws, complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm long (ISI marked), complete all as specified.

Aluminium handle, cast type, anodised, 100mm long (ISI marked), complete all as specified.

Pressed steel frames of size 125mmx60mm for doors with one or more rebates fabricated out of 1.25mm thick mild steel sheets with and including necessary fixing lugs, hinges lock strike plate and making good the existing surface in cement mortar 1:6, complete all as specified.

Pressed steel frames of size 105mmx60mm for doors with one or more rebates fabricated out of 1.25mm thick mild steel sheets including necessary fixing lugs, hinges, lock strike plate and making good the distrubed surface in cement mortar 1:6, complete all as specified.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete, drilled for fixing steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and also hanging, fastening and fixing complete angle as in cup boards (40x40x5mm) conforming to Fe-410W Grade-E-250 quality - A), complete all as specified and directed

PCC 1:3:6 type C-1 using 20mm graded stone aggregate for filling back of pressed steel door frame/chowkhat and fixing of bed block of hold fast etc. Complete all as specified and directed.

Factory made 2nd class hard wood 35mm thick flush door shutters, solid core with particle board exterior grade as per IS - 22002 of 1983 (Part-I). Flush door shutters shall be internally lipped as per clause 8.21 of SSR-1919 Part-I. Flush shutters solid panel construction with one face covered with decorative face veneer with liping/ frame to match on both sides complete all as specified and directed.

2nd Class hardwood glazed and skeleton shutter open rebated and prepared to receive glass gauge etc with rebated sash bars, any number of edges framing plan chamfered or rounded fitted with cut and mitred beads for securing glass etc, size of member of shutter as specified in SSR Part-I Section 8 clause 8.324(a) complete all as specified and directed.

Medium density fiber board (MDF) designer/ fancy shed exterior finished PVC laminated one side, interior grade, one side decorated laminated of approved colour and other balancing side white in colour, cut to size as required and fixed in position for cabinets, including PVC edge bonding tape of same shade and side fixed SR adhesive etc complete all as specified and as directed and approved by AGE/GE.

Stainless steel handles, fancy type, 150mm size and fixed in position with stainless steel screws, ISI marked, suitable for cupboard & rubber wood shutters, complete all as specified and as directed

Euro slip-on hinge, full overlay, shutter cavity 35mm, 12mm deep, 4mm from edge, SS 304 grade, Nickel plated, in repairs, complete all as specified and as directed

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm fixed with stainless steel wire staples or beading etc, complete all as specified and as directed.

150mm Helical Double action door spring, mild steel with steel wire spring, stove enamelled, black complete all as specified and as directed

Blank

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, 300mm long, complete all as specified.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, 250mm long, complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 200mm long (ISI marked), complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 125mm long (ISI marked), complete all as specified.

Blank

Aluminium handle, cast type, anodised, 150mm long (ISI marked), complete all as specified.

100mm size hasp & staple, aluminium, safety type, including bolt to hinge plate and fixed with screws, complete all as specified.

Aluminium handle, cast type, anodised, 125mm long (ISI marked), complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 125mm long (ISI marked), complete all as specified.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30mm, complete all as specified.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm, complete all as specifed.

Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified all as directed by Engr-in-Charge

Powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.), tower bolts 125mm each (2 Nos) complete all as specified all as directed by Engr-in-Charge.

Aluminium deco grill of 5 to 6mm dia size of mesh not exc 7.5cm in either ditection as approved by GE all as directed by Engr-in-Charge.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and or reveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 grade-E-165, complete all as specified.

Sheet glass ordinary quality 4mm thick and glazing with oil putty in sq n.exc 0.5 sqm in each panes fixed to steel, matel frames, complete all as specified and directed.

All as per item above butpin head type, figured glass.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required exc half brick but n.exc one brick complete all as specified.

Prepration of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (for steel surfaces) over one coat of red oxide zinc chrome primer, complete all as specified.

Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint treating ends of posts, backs of chowkats etc area tarred exc 0.1 Sqm but n exc 0.5 sqm each complete all as specified.

Demolition of Cement concrete, un-reinforced in sunken portion of WC, removing all loose particle alongwith existing water proofing treatment, cleaning by wire/ brushes to removing all dirt and cleaning the surface with water etc complete all as specified by Engr-in-Charge.

GI pipe of 50mm dia medium grade inserted at corner projecting out side 20cm fixed complete laid on floor, bore of pipe 50mm complete all as specified by Engr-in-Charge.

Rendering 15mm thick plaster mixed with water proofing compound in cement motor 1:3 provided while concrete is still green complete all as specified by Engr-in-Charge.

Apply a coat of bitumen primer conforming to IS 3384 @0.70 ltr per Sqm after drying applying coat of Hot blown bitumen 85/25 gde @ 1.2 Kg per Sqm, complete all as specified and directed.

Applying self adhesive APP membrane (atactic poly-propylene polymer) 5 layerd 3mm thick weighing not less than 3 KG/Sqm having a center core of polyster non-woven-mat (FP) reinforcement, complete all as specified and directed.

PCC 1:4:8 type B2 for filling of sunken portion after concealling all membrane and sealing all joints with ceiling compound complete all as specified and directed.

Demolition of cement concrete unreinforced of any description in any position not otherwise specifically provided for, complete all as specified.

Demolition of cement concrete, un-reinforced in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified.

PCC (1:2:4) type B-0, using 12.5mm crushed stone aggregate, 25mm thick as in floors finished even and fair using extra cement complete all as specified and as directed.

Vitrified ceramic tiles, light shade 10mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and painted in white or coloured cement to match, laid over and including 10mm thick screed bed in cement mortar 1:4 for laying floor finishes, complete all as specified.

Vitrified ceramic tiles, light shade 10mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in vertical surfaces such as skirting/dado etc., set and jointed in neat cement slurry and painted with white or coloured cement to match over 10mm thick backing layer of plaster in CM (1:3) on brick or concrete surfaces of finshed rough to receive wall tiles, complete all as specified.

Non-skid rectfied jointless light coloured group ceramic tiles 7 to 8mm thick (square/rectangular) PEI Grade-1, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry at 3kg/sqm and pointed in coloured cement to match, laid over and including 10mm thick bedding layer in cement mortar 1:4, complete all as specified.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc., complete all as specified.

Non skid ceramic cololured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm. in floors etc set and jointed in neat cement slurry and pointed in white or coloured to match fixing of tile with screed bed 15mm complete all as specified and as ditrected by Eng-in-charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), racking out joints, hacking for key and scrubbing and removing rubbish off the premises, complete all as specified.

Glazed ceramic coloured tiles 7mm thick 450 x 300mm size in verticle surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade. etc over and including 10mm thick backing layer in CM 1:3 complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar, complete all as specified.

16-18mm thick Granite single piece (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like over 15mm thick in cement mortar (1:4) bedding including pointing in white cement using with pigment to match with shade of granite with and including providing nosing including champhered or rounded edges granite polished to edges of slab and drilling of hole for gas pipe using mechanical method, complete all as specified & directed. Note: Granite stone slab shall be in single piece to fit.

Machine cut kota stone single piece slab flooring 18-20mm thick over 20mm thick screed bed in CM 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including protruding chamfered/rounded edges in threads table rubbed and mirror polished rubbing and polishing complete,

Kota stone single piece slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over including 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing protruding chamfered/rounded edges in thresds table rubbed and polishedand polishing complete,

PVC connection 15mm size with PTMT nuts of length 600mm of approved quality complete all as specified.

15mm bore chromium plated Angular stop valve of cast copper alloy screwed down high pressure with crutch butter fly handle screwed both ends for iron pipe or for unions and fixed in repair, all as specified and directed.

Brass chromium plated shower rose of 125mm size with arm and with or without swivel joints, fixed in repairs, complete all as specified. Make: ESS ESS Cat Part No. RF 202 for Shower and Cat Part No. SA-105 for shower arm or equivalent in Make as per Appx `E' to Particular specification.

15mm dia bore fancy type chromium plated concealed stop valves of cast copper alloy with long shank & cup etc in repairs, complete all as specified and as directed.

Towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges, complete all as specified. Make: Jaquar Cat Part No.ACN 1111SM or equivalent in Make as per Appx `E' to Particular specification.

Soap dish with stain less steel Choromium plated case copper alloy with approximate size 160x160mm, Jaquar CAT Part No. AKP-35731P fixed to plugs on wall with chromium plated brass screws complete all as specified and directed.

Bib tap, 15mm bore, fancy type, , chromium plated with wall flange, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule, fixed in repairs, complete all as specified.

Brass CP mixer 15mm bore for mixing hot & cold water screwed down for iron pipe for Wash Hand Basin with complete all as specified and directed.

Wall telephonic shower of length 1.2Mtr with connecting legs and wall flange make, including all necessary accessories complete all as specified and directed by Engr-in-Charge.

Wall mixture non telephonic shower, complete all as specified and directed by Engr-in-Charge

For sink mixter with regular swining spout wall mounted with connecting legs & wall flanges. Make: Jaquar LYR-38309 or equivalent all as specified and directed

Stainless steel plate rack of size 750mm x 900mm x250mm as per sample kept in GE’s office of minimum thickness of strip not less than 1mm wall, fixed in repairs, complete all as directed.

Stainless steel plate rack of size 600mm x 750mm x250mm as per sample kept in GE’s office of minimum thickness of strip not less than 1mm wall, fixed in repairs, complete all as directed.

Sinks with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm incl 40mm waste fitting etc complete all as specified and as directed

Sinks with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm incl 40mm waste fitting etc complete all as specified and as directed

Mirror cabinet PTMT of 450mmx600mm with magnetic looking arrangement fixed with and including chromium plated brass screws, complete all as specified. Make : Paryag or equivalent all as specified and directed

25mm dia stainless steel curtain rod with and including brackets and knob at both ends as per site requirement including taking down old existing PVC conduit pipes with accessories, complete all as specified. Note : The cost of brackets and knobs is deemed to be included in the quoted rate. Nothing extra shall be paid on this account

25 mm dia fancy type stainless steel curtain rod with and including brackets and knob at both ends as per site requirement including taking down old existing PVC conduit pipe with accessories complete all as specified and directed by Engr-in-Charge Note : The cost of brackests and knobs is deemed to be included in the quoted rate. Nothing extra shall be paid on this account.

Taking up or down steel pipe 15mm bore including or removal to store, complete all as specifed.

Taking up or down steel pipe 20mm bore including or removal to store, complete all as specifed.

Taking up or down steel pipe 25mm to 62mm bore including cleaning for refixing or removal to store, complete all as specifed.

GI water tubing, medium grade, 15mm bore with all fittings, fixed complete to walls and ceilings or laid in floors, bore of pipe 15mm complete all as specified.

GI water tubing medium grade 20mm bore with all fittings, fixed complete to walls nd ceilings or laid in floor, bore of pipe 20mm, complete and all as specified by Enge-in-Charge

Refixing of GI water tubing medium grade 20mm bore fixed, complete to walls and ceiling or laid in floors including cleaning/all necessary fittings, complete and all as specified by Enge-in-Charge

GI water tubing medium grade 25mm bore with all fittings, fixed complete to walls nd ceilings or laid in floor, bore of pipe 20mm, complete and all as specified by Enge-in-Charge

Refixing of GI water tubing medium grade 25mm bore fixed, complete to walls and ceiling or laid in floors including cleaning/all necessary fittings, complete and all as specified by Enge-in-Charge

GI tubing 32mm bore medium grade galvanised pipe for spout laid in sunken portion/floors, complete all as specified.

Taking down rain water pipe any size and any dia all as specified and directed by Engr-in-Charge

PVC (SWR) pipes, 110mm dia, single socketed, in any length with rubber ring joints and epoxy adhesive, fixed to walls, complete all as specified & directed.

110mm bore PVC (SWR) bends any radius and fixed with epoxy adhesive, complete all as specified.

Cast iron floor trap, including jointing with solvent cement, dia of outlet 100mm, complete all as specified.

Cast iron floor trap, including jointing with solvent cement, dia of outlet 75mm, complete all as specified.

Dismantling of cast iron or PVC pipes including all fittings and accessories, 100/75mm dia and in any position all as specified.

Cast iron spun pipes, 75mm double socketed in any length with cement joints, fixed to walls complete all as specified.

Cast iron spun pipes, 100mm double socketed in any length with cement joints, fixed to walls complete all as specified.

Cast iron bends suitable for 100mm, complete all as specified.

Cast iron bends suitable for 75mm, complete all as specified.

Cast iron branch pieces single, (single T) equal or unequal ordinary or inverted (spigot or socket type) or with parallel branches of 100mm dia

Cast iron branch pieces Double, (Double T) equal or unequal ordinary or inverted (spigot or socket type) or with parallel branches of 100mm dia

Cast iron branch pieces single, (single T) equal or unequal ordinary or inverted (spigot or socket type) or with parallel branches of 75mm dia

Cast iron branch pieces Double, (Double T) equal or unequal ordinary or inverted (spigot or socket type) or with parallel branches of 75mm dia

Cast Iron vent cowl of size 100mm bore, complete all as specified.

Cast Iron vent cowl of size 75mm bore, complete all as specified.

Gun-metal, globe or gate valves of 20mm dia, with iron wheel head, screwed both ends for iron pipe & fix in repair, complete all as specified.

Vitreous China squatting pan of Orrissa pattern of approved make of size 580 mm X 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to antisyphonage pipe etc including making good to floor, in repair, complete all as specified and directed. Make : CERA cat part No. Calina S 3010102 or equivalent in make as per Appx 'E' to Particular Specifications

Vitreous china wash down water closet (pedestal pattern) white pan with complete one set with incl flushing cistern and all fittings, connections incl making connection to drain and flush pipe, fixed in repairs with toilet jet complete all as specified and as complete all as specified and as directed by engr-in-charge.

Plastic water closet seat, white colour closet patttern with flat bottom and cover and incl mild steel chromium plated or aluminum hinges device complete fixed in repairs, all as specified. Make : CERA cat part No. B1510121, Jaquar-CNS-WHT-WCS 1 or equivalent of any approved make as approved by GE.

PVC low level cistern of 10 ltrs capacity with top push button inclusive of brackets and PVC bend long type and connection to flush pipe of any size and pattern with inlet ball valve float and handle complete of approved makes, complete all as specified and as directed.

Corner glass shelf set of three etc complete all as specified and directed by Engr-in-Charge.

Wash hand basin of size 550x400mm vitrous China white flat back including brackets, waste coupling & PVC waste pipe of 32mm dia etc, in repair . complete all as specified and directed.

Taking down old PCC tiles from roof and removing bedding at any position all as specified and directed.

15mm thick cement plaster in cement mortar 1:3 on roof surfaces finished even and smooth without using extra cement, incl mixing of water proofing compound for accessible roof/Non Accessible roof.

Priming the roof surface with bituminous primer conforming to IS - 3384 @ 0.30 litres/Sqm, complete all as specified and directed

Applying a coat of hot blown 85/25 grade bitumen conforming to IS - 702 @ 1.20 kg/Sqm and leaning the surface thereafter

Cement Concrete Tiles with cement and no pigment 25cm x 25cm x 22 mm thick machine pressed set jointed and including 15mm screed bedding in CM 1:4 as pointed in neat cement slurry in flooring as cut and polished

Taking down existing roof treatment of any description and any type, complete all as specified and directed

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc, and brushing neat cement slurry with 3.00 kg of cement per Sqm,complete all as specified.

Supply only Liquid water Proofing Compound

Priming the roof surface with bituminous primer conforming to IS - 3384 @ 0.30 litres/Sqm, and applying a coat of hot blown 85/25 grade bitumen conforming to IS - 702 @ 1.20 Kg/Sqm and thereafter provide polymetric water proofing membrane (5 layered) 3mm thick and weight not less than 3Kg/Sqm with centre layer core of 90 micron, high molecular density polyethylene film followed by another coat of semi hot blown 85/25 garde bitumen @ 1.20 Kg/sqm blinded with fine sand in dry condition @ 0.50 Kg/Sqm with 02 coat of aluminium paint, complete all as specified and directed

Making benching with PCC (1:2:4) type B0 using WPC along sidewall adjoining to roof in concave shape, complete all as specified and directed

Taking down cement plaster including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed

Rendering 10mm thick in patches in cement mortar 1:6 on other than fair face of brick work of concrete surfaces and finishing the surface even and smooth without using extra cement, complete and directed all a specified

Rendering 15mm thick plaster in CM 1:4 mixed with WPC as per manufacturers instruction in two layer (10mm+5mm) in patches in cement mortar in 1:4 on fair face of brickwork or concrete surfaces even and smooth withoout using extra cement and with using integral water proofing compound, complete and all as specified and directed

Rendering 5mm thick in cement mortar 1:3 on ceiling, complete and all as specified and directed

Reinforced cement concrete type A1 1:11/2:3 (12.50mm graded aggregate) as in chajjas, complete and all as specified and directed, including use and waste of form work ( The work is required to be carried out upto G+3 storey building )

Demolition of brickwork of any type in cement mortar condition etc, complete and all as specified and directed

Brickwork sub class B brick straight or curved on plan to any radius in half brick thick wall in CM 1:4, complete and all as specified and directed

Brickwork built in cement and sand mortar 1:6 with sub class 'B' old size bricks straight or curved on plan exceeding 6m means radius, complete and all as specified and directed

PCC (1:3:6) type C-2 (using 20mm graded crushed stone aggregate) 75mm thick plinth protection, complete and all as specified and directed

Demolition of RCC of any description such as kitchen chimney, chajja, shelves, OHT Tanks etc and in any position not otherwise specially provided for, complete and all as specified (Reinforcement cut as required to facilitate demolition) and directed by Engineer-in-Charge

Reinforced cement concrete type A1 1:11/2:3 (20mm graded aggregate) conforming to M-15 grade as in slab supported on walls, beams and column in floors, roofs, landings, balconies, deck slabs and in shelves and etc and setting in mortar complete with joints to match,complete and all as specified and directed

TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, ,complete and all as specified and directed

TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips,complete and all as specified and directed

Use and waste of Formwork rough finished surfaces of soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick, complete and all as specified and directed

Use and waste of Formwork to edge of concrete flat treads breaks in floor window cill concrete railing opening of concrete wall, floor, roof n.exc 20cm wide and side of RCC bands in wall Horizontal/sloping and similar works exc 10cm but n.exc 20cm wide for roughed finished surfaces of concrete,complete and all as specified and directed

Formwork to chullah hoods, chajjas, troughs and similar items including edges, complete and all as specified and directed

Dismantling water tank and removing to store of capacity exc 250 litre but not exc 500 litre, complete and all as specified and directed

Dismantling water tank and removing to store of capacity exc 500 litre but not exc 1000 litre, complete and all as specified and directed

500 litre capacity rotational moulded polyethylene in white colour three layered ISI Marked water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position, complete and all as specified and directed

1000 litres capacity rotational moulded polyethylene in white coloures three layered ISI Marked water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position, complete and all as specified and directed

20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm - 210 gms) and fixed, complete all as specified and as directed.

Removal of vegetations from roots etc on wall/Roof area n.exc 1.00 sqm each by applying suitable chemical and making good the surface by grouting the holes and matching the plastered surfaces 15 mm thick in cement mortar (1:3) complete all as specified and directed.

Preparing new plastered surfaces by applying 1mm thick wall care putty, two coats of OBD/on new plastered surface over a coat of primer of any description of approved tint over new plastered surface, complete all as specified and directed

Preparing new plastered surfaces and applying 3mm thick wall care putty on wall surface and smoothening the surface with sand papers/mechanical sanding etc and applying two coats of Oil Bound Distemper of approved tint over a coat of alkali resistent primer, complete all as specified and directed

Preparation of surfaces and applying three coat of white wash on newly plastered surface of ceiling etc, complete and all as specified and directed

Preparation of new plaster surfaces of wall and applying two coat of exterior emulsion weather proof as per manufacturer instruction, finishes etc, complete and all as specified and directed

Painting to new wooden surfaces over 10cm width or girth for applying two coats of synthetic enamel paint over a coat of alkali resistant primer paint including wall care putty finishes, complete and all as specified

Repair Eye Door viewer (magic eye) fixed in position for door shutters complete all as specified and directed by Engineer-in-Charge

Door Seal ISI marked of approved quality 50mm wide and of thickness not less than 3mm fixed with stainless steel screws at bottom of the door shutters, complete and all as specified and directed

Stainless Steel fancy type peg set of four and fixed in position with steel screws, complete and all as specified and directed

Antitermite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron, complete and all as specified in SSR Part - I and directed

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match with existing floors, complete and all as specified and directed

Anti termite treatment of voids in masonry using chemical emulsion (Cholorophyrus 20% EC) one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors, complete and all as specified and directed

Precast cement concrete type B0 1:2:4 (12.5 mm graded aggregate) louvers and jallies 25mm thick (measured solid) including all moulding but excluding frames set in cement mortar 1:4, complete and all as specified and directed (Pre Cast Frame shall be measured and paid seprately )

Precast cement concrete type B1 1:2:4 (20 mm graded aggregate) as in bressumers, steps quoin blocks (for use with masonry) and set in cement mortar 1:4, complete and all as specified and directed

Factory made solid PVC moulded door/cupboard shutters 28 to 30mm thick (stiles) designed with 2mm thick moulded prelam PVC sheet on the front face & 2mm plain colour PVC Sheet on back face, complete all as specified and directed

Grinding and polishing existing kota flooring all as specified and as directed by Engr-in-Charge

Stainless steel toilet paper holder of suitable size all as specified and as directed

Chicken wire mesh for roof treatment all as specified and as directed by Engr-in-Charge.

Providing and maintaining Barricading on the site 2.5 m high by using MS Pipes or angle iron frame work of verticals at 3 m c/c and horizontals at 0.90 m c/c, Galvalume sheets, Struts, MS Clamps, etc. The verticals shall be embedded/ fixed to concrete pedestals below ground. The rate to include fabricating, cutting and fixing in position MS frame work, painting the same with two coats of approved anti rust paint, etc complete. Contractor to get structural design approved by the Engineer. Contractor shall remove and take away the barricading at his own cost on completion of the works.

Chipping /removing loose concrete up to reinforcement bars, without damaging the reinforcement, removing all the loose materials and to make all the exposed surfaces free from oil, dust and all impurities etc. complete.

Removing corrosion of steel reinforcement by mechanical means like wire brushing, chipping to remove loose rust and then applying rust removal solution by using brush application, leaving the surface for at least 15 to 30 minutes, then removing loose materials by scrubbing or with brush and applying polymer bond to the old concrete surface before applying Polymer mortar. Make :- SIKA- SIKA Rust off 100 or SIKA S.B.R or Latex Power FOSROCK - Reebaklens RR or Nitobond AR

Application of Corrosion Inhibitor: Providing & applying One coat of Concrete Penetrating Corrosion Inhibitor (Surface applied) which works on Bipolar Inhibition Mechanism on entire concrete surface to be repaired by using brush or spray at 250 ml per Sq.Mt./Coat or as per manufacturer’s specification and prior to application of first coat of anti corrosive coating to reinforcement. Make :- SIKA - Feroguard 903 FOSROCK - Nitozink

Providing Micro Concrete jacketing to walls/ columns or beams of thickness upto 75 mm using Polymer modified cement premixed quartz sand aggregate packed in bags of standard manufacture, for high early strength of 40 N/mm sq.cm of approved brand. The dry product is to be mixed with 12.5% water by weight, along with washed and poured into rigid form work moulds & tamped properly, & cured for 3 days. [Payment is to be made by weight premixed of micro concrete product consumed as per site register records. No extra payment shall be made for shuttering or any other material. Make :- SIKA - Sika Rep microconcrete-4 FOSROCK - Rendero CRG

Providing and applying Polymer modified cement mortar of average thickness 15-20mm using Polymer in one or more layers in proportion 1:5:15 of Polymer Cement Quartz Sand as manufacturer’s specifications in specific layers, curing the surface after 72 hours of application with wet gunny bags etc and by finishing the surface with 12mm thick (1:3) Cement sand plaster. Make :- SIKA - Sika 122 WL FOSROCK - Renderoc S2

Providing and applying Polymer modified cement mortar of average thickness 30-40mm using Polymer in two layers in proportion 1:5:15 of Polymer Cement Quartz Sand as manufacturer’s specifications in specific layers, curing the surface after 72 hours of application with wet gunny bags etc and by finishing the surface with 12mm thick (1:3) Cement sand plaster. Make :- SIKA - Sika 122 HS FOSROCK - Renderoc HS xtra

Shear Connectors: Make 10/12 mm dia holes using heavy duty electrically operated hammer drills in the concrete of RCC members to a depth of about 75 mm at 500 mm c/c or at suitable grid in zig-zag fashion, clean the holes using air jet and fix pre-fabricated 100 x 50 mm L-shape 8 mm dia rebar using Anti Corrosive protective coating so that 75 mm out of 100 mm is inserted inside the concrete and 25 mm remain outside along with 50 mm bend. The shear connectors are used to tie the additional reinforcement bars. FOSROCK - HILTI, Ficher

Bond Coat: Providing & applying One coat of structural grade epoxy bond coat by brush conforming to ASTM-C-882-87 to the prepared concrete surface to be repaired / strengthened. This is applied prior to the application of polymer repair mortar / epoxy mortar / Microconcrete to have monolithic action between old concrete surface and new concrete surface. Make :- SIKA - SIKADUR 32LP, HIBOND, FOSROCK- Nitobond EP

Providing and applying priming cum bonding coat of polymer of approved make and quality as approved by engineer- in - charge and cement slurry in 1:1 proportionate by weight to concrete area by brush or any other established method etc. complete. Make :- SIKA - SIKALalex or SRB FOSROCK- Nitobond EP

Provision of modular kitchen cabinet made of "12mm thick Medium Density fibre board (MDF) designer / fancy shade exterior finished PVC laminated one side and other side white in colour", SS handels, SS telescopic channels, SS brakets, SS hinges, SS basket and necessary fittings & nuts (Size of cabinet (1.8mx0.6mx0.7m) complete all as specified and all as directed by Eng-in-charge. NOTE :- Each kitchen cabinet consisting of six no. basket (03 of size 200 X 450 X 530) weighing 5.12kg other (03 of size 150 X 450 X 530) weighing 3.46 Kg having telescoping channel of length 450mm (12 Nos) with SS Euro Slip Hinges (12 Nos) with SS handle (12 Nos) duly approved by GE / Engr-in-Charge

Stainles Steel Hand Rails of Grade 104, half round or other stock section or core for SS hand rails straight portion,drilled and countersunk for baluster running bars ,nosing to steps including embeding in concrete and screwing etc.wind ties for roof including securing bolts ,posts and strut in fencing ,incl cutting tops to shape as dircted ,drilling holes ,notching for wire,etc ,S S fillets incl all necessary drilling,bolting or riveting,etc and similar work confirming to ncl curved or ramped portions of hand rails to required shape or figure (curved,ramped or scroll portion complete all as spd and directed by engr-in-charge.

Taking down copper/aluminium point wiring (light fan socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good disturbed surfaces of walls, floors, etc. all as specified and as directed by engineer in charge.

Taking down old unserviceable copper / aluminium submain wiring any type / size from existing old surface for further repair / replacement complete all as specified and as directed by engineer-in-charge

Taking down carefully by unscrewing from boards / outlet boxes fittings and fixture such as, LED bulk head fitting, LED tube light fitting etc. for re use at site or carrying to the store (serviceable fitting shall be reuse) all as specified and as directed by engineer in charge.

Taking down un serviceable Main switches/MCB DB with MCB etc after disconnecting for schedule of credit all as directed by engineer in charge.

Point wiring for one light/ceiling fan/bell controlled by one switch with 1.5 sqmm (nominal area) PVC insulated and PVC unsheathed multi stranded copper conductor cable FRLS in and including concealed PVC conduit 20 mm dia medium duty ISI marked, including suitable new annealed sunken boxes,modular frame and cover plate for fixing of modular switches as per required point in that board, flush to surface for one light point/ fan point/ Bell point controlled by one switch including PVC insulated unsheathed 1.5 sqmm copper conductor cable FRLS connected to common earth dooly complete including cutting,chasing the surface and then making good the same in CM 1:3 complete all as specified and directed. Make of cable :- Anchor/Havells/ fiinolex and Make of conduit :- Kalinga/Polycab/Havells (Note : Switches, Sockets etc shall be measured and paid for separately under appropriate items of Sch 'A

All as per item No. 168 above but for one 3 pin, 5 Amps socket outlet on independent board.

All as per item No. 168 above but wire size 2x2.5 Sqmm and providing earth continuity wire using PVC insulated, unsheathed single core stranded copper conductor FRLS cable of size 2.5 Sqmm. to controlled the 3 pin 5 / 15 Amps socket outlet on independent board.

All as per item No. 168 above but point wiring with 1.5 Sq. mm copper conductor, single core, PVC sheathed, cable, to control one 3 pin socket outlet, 5 Amps on the same board with other switch.

All as per item No. 168 above but control by 2 Nos.of two way switch.

Modular switch single pole one way 06 Amps 1 module complete all as specified and directed

Modular switch single pole two way 06 Amps 1 module complete all as specified and directed

Modular switch single pole one way 16 Amps 1 module complete all as specified and directed

Modular socket 6 /16 Amps 2/3 pin flush type complete all as specified and directed

Modular electronic fan regulator, step type, two module 120 watt 230 volt and making all necessary connections complete all as specified and directed.

Modular socket 6 amp-2/3 pin combined 2 module complete all as specified and directed.

Modular Bell push 6A, 1 module complete all as directed by Engineer- in - Charge.

Modular motor starter suitable 25 Amp 2 module for split type Air conditioner complete with suitable gang box and cover plate all as specified and as directed by engineer incharge.

Slim linear LED lighting fixture 4/5W watt LED batten, with full base of extruded poly carbonate isolated driver, complete making all connection from ceiling rose to fittings including testing complete all as per the direction of Engr-in-Charge. Make of LED -Syska Cat No:SSK-SQ0401/Wipro Cat No : D530565/C&S Cat No: LTTBIF5WLED/W/ Havells: Cat No: LHEXBXPNIN1W005

Taking down fan, ceiling cable end, dismantling blades and kept in safe custody for refixing on same location all as specified and directed by engineer in charge. Note :- "Contractor rate shall include taking down and refixing in same position after necessary repair as described in relevant item of schedule"

Repair of ceiling fan 1200mm sweep of any make obtained from above item, oiling, greasing cleaning slot & replacement of defective nut bolts washer etc including painting all as specified and directed by Engr-in-charge.

All as per BOQ item no 183 above, but complete over hauling after including rewinding

Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 M below normal ground level, connected to 4 mm earth lead by means of bolts, nuts, check nuts and washers of galvanised iron of steel all as shown in electrical plate No. 5, including Excavation, PCC, Funel and GI protection pipe etc. connected to earthing test point all as specified or indicated including testing on completion.

All as per sr item No 185 above but using galvanised MS strip 32x6mm as earthing lead all as specified and direct by engr -in- charge.

Sheet metal TPN DBs - 160/250 MCCB DBs 04 way (250+12) with metal door 415 volts grade IP 43 Protection Grade fixed flush to wall complete including connections should be provide with necessary reducer lugs all as specified and directed by Engr-in-charge.Make Legrand Cat part No : 5077 50 or equivalent to Shnieder

Single pole and neutral sheet steel powder coated distribution board for MCBs fitted with bus bar neutral link Earth bar and din rail suitable for use on 240V, 50Hz supply double door SPN DB system 8 Way all as specified and directed by engineer in charge. Make : C&S Cat No:CSDBSPNDD08/ Standard Cat No: DSDNSHODXW08/ Indo Asian Cat No : 810321

Thermal magnetic MCCB 4 pole 160 Amps 415 Volts 16 ka INCLUDING MAKING NECESSARY ARRANGEMENT all as specified and directed by engineer in charge for MCCB DB.

Thermal magnetic MCCB 4 pole 100 Amps 415 Volts 16 ka INCLUDING MAKING NECESSARY ARRANGEMENT all as specified and directed by engineer in charge for MCCB DB.Make Legrand (4202 15)/ IndoAsian Cat No: 830022/ or equivalent.

Thermal magnetic MCCB 4 pole 40 to 63 Amps 415 Volts 16/18 ka INCLUDING MAKING NECESSARY ARRANGEMENT all as specified and directed by engineer in charge for MCCB DB.Make Legrand (4202 13)/ IndoAsian Cat No: 830095 / or equivalent makes to Standard

Connection and testing 'C' series SPN MCB 40 to 63 Amp 240V, 50Hz, 10kA for lighting and other domesitc loads incl necessary copper lugs etc all as specified and as directed by engineer incharge. Make C&S Cat No: CSMBS2C40/ IndoAsian Cat No: 810078/ or equivalent makes to Standard

Supply fixing connection and testing MCB SP6-32 Amps

Supply fixing connection and testing MCB SP 40 Amps

Taking down serviceable/unserviceable electric meter including meter box from existing position carefully for refixing including making good to disturbed surfaces (Note : Disturbed surfaces should be made good by Plastering/distempering/colour washing/white washing to match with existing surfaces)

Re fixing of serviceable electric meter obtained from BoQ item No 195 above with meter box by scouting to the wall and fix firmely all as specified and directed by engineer in charge.

Slim linear LED lighting fixture 20 Watt LED batten, P.F greater than 0.9, input voltage range from 90 Volts to 280Volts with full base of polycarbonate extruded section acting as a heat sink with closed back isolated driver complete making all connection using 1.5sqmm copper conductor multistranded PVC insulated 2 core flexible cable with from ceiling rose to fitting complete all as specified and as directed by engineer in charge.Make Make : Syska Cat No: SSK-SQ2001/Havells Cat No: LHEXBXPNIN1W020/ or equivallent to Wipro

Supply and fixing LED Bulk head (6500K) fitting of 09/10 Watt surface mounting type extruded aluminium body with diffuser complete with testing all as specified and directed by engineer in charge. Make Syska Cat No: SSK-BH-9W /Wipro Cat No : DA11265/Crompton :Cat No: LBHE-10-DL /Havells: Cat No: RUGBYNEONFT10WLED860SSYMTOPC

Decorative ultra slim linear polycarbonate Extruded LED lighting fixture 10/12 Watt LED of input voltage AC 220V-240V, 50 Hz with colour tempetrature 6500K more than 1080 lumens of IP 20 complete making all connection using 1.5 sqmm copper conductor multistranded PVC insulated twin core flexible cable from ceilingrose to fitting complete all as per directed by Engr-in-charge. Make Syska Cat No: SSK-SQ1201 Wipro Cat No : D531065/Havells: Cat No: LUMILINEPLUSBS10WLED865SPCSS/ Philips Cat No : BN 021 LED10S- 6500 PSU GR S1

Supply and hanging ceiling fan of 1200 mm sweep, white in colour , including all electric connection and testing complete Make : Havells cat No : ES-50 Premium/Standard model- Breezer metalic finish pearl white /Bajaj Leatrim Max makes all as specified and directed by Engr-in-charge.

Supply and fixing ventilating fan of 150 mm complete with louver and mounting assembly including fixing exhuast fan with grouting of nut & bolts complete making holes for mounting the same Make Havells Model Ventil Air - DS or equivallent to other makes of Crompton Greeves /Bajaj all as as specified and directed by Engr-in-charge.

Wiring for circuit / Submain Wiring in PVC cocealed conduit not less than 25 mm dia with 2 x 6 Sq.mm main wire and 1 x 6 Sq.mm earth wire of FRLS, PVC insulated copper conductor, single core cable complete all as directed by Engineer - in - Charge.

Wiring for circuit / Submain Wiring in PVC concealed conduit not less than 40 mm dia with 4 x 10Sq.mm main wire and 2 x 10 Sq.mm earth wire of FRLS, PVC insulated copper conductor, single core cable complete all as directed by Engineer - in - Charge.

Taking down serviceable Electric water heaters (Geyser) of any type and capacity, keeping aside safely to deposit to MES store and re fixing the same after making minor repair like replacing heating element, thermostate,etc. to its original position and tesing, complete all as specified and directed by engineer incharge.

Geyser 25 Ltrs capacity Vertical type BEE5 star rating suitable to operate in Single phase AC supply,230 volts 50 Hz including suitable size heavy duty Pvc connection hot & cold and grouting nut bolts on the wall as per site requirment all as specified and directed by EIC. make Havells SEN ZO Cat No:GHWASESWH025 White 5star rating or equivallent to Bajaj Calenta / Racold Model Electro swift.

Supply, Installation & Commissioning of Factory made, manufactured by a CPRI approved Manu-facturer, Self supporting Totally Enclosed LT PANEL BOARD Compartmentalised Design, Dust & Vermin Proof of size not less than 2000X1800X500mm suitable for 440 Volt 3 Phase 4 Wire System made out of 2.0mm thick CRCA Sheet and built upon Rigid Frame Work having Front and Rear hinged Door with Neoprene Rubber Gasket, Epoxy Powder Coated including Danger Plate, Earthing Strip Point and Ventilation Louvers at the Rear Side, Bottom detachable Gland Plate complete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. having Control Circuit Diagram with Colour Code Solid Conductor Copper 1.5 Sqmm Cable for easy identification including Incoming/Outgoing Cable Holes at Bottom, embedded with 50X6mm Mild Steel Angle Iron Frame and 200mm above the Normal Ground Level complete with PCC Found -ation in Cement Concrete 1:2:4 (20mm Graded Stone Aggregate) and Testing after Installation including taking down unserviceable LT Panel Board, complete all as specified and comprising with the following :–( For P-19 (08 DU Offrs Qtrs)

a) Aluminium Bus-bar 800 Amp, supported with suitable size of heavy duty Porcelain Stand Lock with suitable size Brass Nut, Bolts and Washers with Heat Shrinkable PVC Sleeving. The Bus-bar shall be Colour Coded (Red, Yellow and Blue) for 3 Phase and Black for Neutral.: - 4 Nos b) MCCB TPN, 400 Amp, 3 Pole, 415 Volt, 36 KA Breaking Capacity duly connected to Bus-bar as INCOMING- 1 nos (c) MCCB TPN, 63 Amp, 3 Pole, 415 Volt, 16 KA Breaking Capacity duly connected to Bus-bar as OUT GOING 08 nos (d) Digital Multi functional meter - 01 set (e) LED Indicating Lamps (3 No.) with Holder for Main Supply indicating RYB - 01 set NOTE: 1. All Internal Connections shall be connect-ed by Aluminium Strip of suitable size and Capacity to MCCB for which Cost of the same shall deem to be included in the QUOTED UNIT RATE. (f) Fixing only serviceable three phase Electric meter retreaved from Item No 32. - 08 Nos

Taking down/removing existing serviceable UG cable connection of any size from Wall Mounted Panel Board by making cutting chases on wall/ floor to extend the shorten UG cable of any type/size from Loop and making fresh to reconnect the same with suitable aluminium lugs complete including distribute the load equally on each phase all as specified and directed by Engineer in charge. Note : Cutting of Wall /Floor shall be measured and paid separately.

Cutting of hard standing n.exc 45 Cm depth, and n.exc 30 Cm width for taking out/laying UG Cable including making good disturbed surface as per existing all as directed .

CITY 3 Decorative wall light fixture made up of polycarbonate, suitable for 15 Watt retrofit CFL/LED (B-22 Base) complete INCLUDING 15 Watt LED Lamp all as specified and as directed by engineer in charge.

Fixing only serviceable light fittings any type as obtained against item No 166 above all as specified and directed by engineer incharge

Complete all as item No 202 above, but Submain Wiring in PVC concealed conduit not less than 25 mm dia with 2 x 4 Sq.mm main wire and 1 x 4 Sq.mm earth wire

CREDIT SCHEDULE: Deduct credit schedule Part-II Rs 10,10,995.00 (Minus) as listed in Schedule. Note: Tenderers will not quote against this item being a firm amount. Contract Sum will be worked out after deducting the credit schedule amount during acceptance of tender.

M/s Khajuria Construction Co.

M/S KAPIL KUMAR KHATTAR