PROVN OF TOILET FACILITY FOR TROOPS NEAR STN HQ, 06 x CAR PARKING SHED IN BUILDING No.P-03, P-04 AND P-05 OFFRS MD ACCN AT DUNDAHERA MILITARY STN AND ADDN/ALTN TO EXISTING ROOFING SHEET AT BUDDHA TERRACE AREA AND CERTAIN ALLIED WORKS AT MANEKSHAW CEN

Amount

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc for manholes, pipes, wells etc not exceeding 10 sqm on plan and not exceeding 1.5m in depth and getting out in any type of soil, complete all as specified and as directed.

Returning, filling in, inluding spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25cm thick each in trenches, after the pipes have been laid and tested, complete all as specified and as directed.

Removing excavated material hard/dense soil exc 50 m but not exc 250 m deposited where directed at a level n.exc 1.5 m above the starting point for soil, complete all as specified and as directed.

M&L for plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete, complete all as specified and as directed.

M&L Brick work with sub class 'B' bricks strainght or curved on plan not exceeding 6m mean radius built in cement mortor 1:6, complete all as specified and as directed.

M&L for 15mm thick rendering with ready mix plaster on faces of brick or concrete surface, finished even and smooth without using extra cement, complete all as specified and as directed. Note:- 1. Make of readymix plaster shall be Birla Aerocon/Ultratech readiplast/ACC Accoplast / Fosroc Chemical (India) Pvt Ltd Renderoc and as approved by GE) 2. The readymix plaster shall be procured directly from the manufacturer or their authorised dealer. 3 The contractor shall produced original purchase voucher of readymix plaster while claiming RAR/ Final Bill.

M&L for precast reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in cover slab etc. set laid and dry, including provision of necessary formwork, complete all as specified and as directed. Note : (i) Reinfocement shall be measured and paid seperately.

S&F TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including muld seel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

S&F Mild steel of Gde Fe-290 (Gde E-165) as in bend, straps, rungs, handle, holdfast, manhole cover frame and similar small articles, complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors over and including 15mm thick screed bed in CM (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed.

M&L for joint free glazed ceramic coloured tiles in vertical surface 450x300x7 mm thick over and including 10mm thick rendering as in backing/bedding layers of tile in CM 1:4, set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer, complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and as directed.

M&L for 15 mm bore GI tubes, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid floors or concealed, complete all as specified and as directed.

All as per item No.14 above, but 20 mm bore of pipe, complete all as specified and as directed.

Cutting chases or making holes, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and as directed.

S&F vitreous china wash down water closet pan (pedestal pattern) , white including plastic seat cover of closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and as directed.

S&F PVC valveless, syphonic action type flushing cisterns 10 ltrs capacity, low level, white, with inlet ball valves, float and handle including brackets and PVC flush pipe 32 mm dia for low level, complete all as specified and as directed.

S&F brass chromium plated health faucet alongwith 1.00 to 1.50 meter good quality SS flexible connection pipe suitable for 15mm bore pipe, complete all as specified and as directed.

S&F vitreous china wash hand basin, white, angle back, size 400 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets etc. complete all as specified and as directed.

S&F PVC connections 450mm long with brass unions at both ends suitable for 15mm bore pipe, complete all as specified and as directed.

S&F 15 mm bore angle valve/ stop valves, cast copper alloy , chromium palted, fancy type screwed down high pressure with crutch and butter fly handles, screwed with iron pipes or for union, complete all as specified and as directed.

S&F bib tap (quarter turn), brass chromium plated fancy type, long body with flange screwed down, screwed for iron pipe 15 mm bore, complete all as specified and as directed.

S&F pillar tap, brass chromium plated fancy type with capstan heads, screwed down high pressure, screwed for iron pipe 15 mm bore, complete all as specified and as directed.

S&F in repairs chromium plated grating with 100mm dia of approved make including fixing to floor/ nahni trap etc. in CM 1:4 complete all as specified and as directed.

S&F brass chromium plated tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges of brass CP, complete all as specified and as directed.

S&F brass chromium plated soap dish 150mmx150mm, of any type, fixed to plugs with chromium plated brass screws, complete all as specified and as directed.

S&F factory made solid PVC chowkhat/ door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet and edges painted to match with printed PVC sheet reinforced with 19mm x 19mm MS square tube of 19 gauge including rubber gasket, PVC fastners, screws, brackets, and shown on drawing as per SSR part-II (2020), complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick wood grain printed moulded prelam PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and as directed.

S&F stainless steel butt hinges, size 100 mm complete all as specified and as directed.

S&F stainless steel barrel tower bolts, 150 mm long, complete all as specified and as directed.

S&F stainless steel handles, 150 mm long, complete all as specified and as directed.

S&F stainless steel sliding door bolts 250mm long with hasp, staple (bolt type) fixing clips of sheet cast, fixing bolts, complete all as specified and as directed.

S&F machine pressed Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of and colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with steel J-bolt/ hook and nut including washer and drilling to fix the J bolt complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and as directed.

S&F gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore, complete all as specified and as directed.

S&F gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 15 mm bore, complete all as specified and as directed.

S&F Rotational moulded polyethylene water storage tanks 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F Ball brass valves, of 15mm bore high pressure, with polythene float and flynut screwed for iron pipe or brass ferrule complete all as specified and as directed.

M&L for plain cement concrete (1:2:4), type B-1, using 20mm graded stone aggregate as in coping and similar work etc. including weathering, slightly rounded or chamferred angles and throating including provision of necessary formwork complete all as specified and as directed.

M&L for plain cement concrete (1:4:8) , type D-2, using 40mm grade stone aggregate as in concrete bed to drain pipes laid to falls in trenches in any depth including packing under and haunching against the sides of pipes for 150mm bore pipes with concrete after the pipes are laid and tested, complete all as specified and as directed.

M&L for SGSW drain pipes 150mm bore laid in trenches and jointed in CM (1:3) complete all as specified and as directed.

M&L for plain cement concrete(1:2:4), type B-I, using 20mm graded stone aggregate as in surface channel/drains inside the manholes and like including weathering, slightly rounded or chamfered angles and throating as directed and provision of necessary formwork to any extent and finished exposed surface even and smooth without using extra cement complete all as specified and as directed.

Extra over surface channel inside of manholes for forming fair finished drains of channels 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends (Inner girth only shall be measured and paid) complete all as specified and as directed.

Construction of septic tank for 50 users complete all as specified and as directed including shown on drawing forming part of tender. (Drg No TD DZ-171).

Construction of soakage well of size 1.8M X 3.00M (for 50 users) deep complete all as specified and as directed including shown on drawing forming part of tender. {Drg No.DZ-1124(R)}.

Dismantling plain or corrugated polycorbonate sheeting of any guage, thickness including fixture fixed with self tapping screw etc including removing from site complete all as specified and as directed.

M&L for 6 mm thick multi layer coloured polycarbonate plastic translucent sheeting fixed with aluminium strip and gasket and self taping screws on roof trusses ETC. complete all as specified and as directed. Note:- The cost for the following is included in the unit rate quoted by contractor:- a) Scaffolding upto height of 10 meter. b) Making the joints of Polycarbonate Sheets as leak proof.

S&F aluminium composite panels cladding of approved make having total thickness of 4 mm (Top coil -0.5mm, non Toxic PE Core - 3 mm and back Coil -0.50 mm) with 25 micron PVdF Coating on top coil and polyester / epoxy coating on back coil (4-7 microns) on aluminium substructure fixed with 19 mm x 12 mm x 1.6 mm aluminium cleat and 10x100 mm SS Wooden screw with PVC plug on faced horizontal/ vertical surfaces of rectangular / circular columns, suspended ceiling Cills, jambs, canopy including neccessary aluminium frame, scaffolding etc and making 12 mm to 20 mm wide grooves and applying non staining and non streaking sealant of Dow corning (789 or 991 HP) and backing rods of approved shade complete all as specified and as directed. Note : (i) Only exposed surface shall be measured and paid for. (ii) ACP material shall be for exterior application and of shade as approved by Garrision Engineer.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm each, complete all as specified and as directed.

M&L for reinfoced cement concrete nominal mix type A-1, 1:1.5:3 (using 20mm graded stone aggregete) as in foundaion, footing, foundation beams, bases for columns and mass concrete etc. complete all as specified and as directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS : 1161-1979 grade St.-240, complete all as specified and as directed.

S&F MS plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410-W (Gde-E- 250) quality-A, complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep in any type of soil and getting out including clearing all grass vegetation, saplings, shrubs, brush woods under growth roots and trees exceeding 30 cm girth, complete all as specified and as directed.

M&L for 100mm thick PCC 1:4:8, type D-2, using 40mm stone aggregate as in sub base of intelocking path, complete all as specified and as directed.

M&L for 60mm thickness Machine pressed pre-cast concrete interlocking paver block of any size and shape conforming to IS 15658-2006, M-30 grade with grey cement and no pigment, laid over and including 40mm thick sand cushion and joints filled with sand complete all as specified and as directed.

M&L for continous road edging with pre-cast cement concrete blocks (1:3:6) using 20mm graderd stone aggregate, blocks exceeding 10cm thick (size of block 300mm x 100mm x 250mm) with plain fair faces with or without chamferred edge and setting and jointing in cement mortar 1:4 including necessary excavation in hard/dense soil, tamping ground aroiund blocks and removal of surplus soil to a distance not exceeding 50 metre, complete all as specified and as directed.

M&L for point wiring with PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded FRLS type copper conductor cable of size 1.5 sqmm as earth continuity conductor connected to common earth dolly in and including PVC concealed conduit 20 mm dia medium grade ISI marked and its accessories including provn of new factory made pressed steel modular switch/terminal box of suitable size and new modular front & back plates of approved colour/model of suitable size for housing the modular switches, sockets, fan regulators complete all as specified and as directed for the followings:-

One light/fan/exhaust fan point controlled by one way 5 Amp switch.

One three pin 5 Amp socket outlet point controlled by one way switch on independent board.

One three pin 5 Amp socket outlet point controlled by one way switch on same board.

All as per item No.59 here in before, but with 2.5 sqmm (for phase, neutral) and 2.5 sqmm (for continuous earth wire) cable for one 15/16 amp socket out let point on independent board.

Notes for Srl item No.59:- (i) Cutting chases for concealed conduit and making good in cement mortar is deemed included in unit rate. (ii) No cutting shall be done in the roof for laying PVC conduit for ceiling point wiring. In this specified portion, wire shall run through the existing conduit or new surface conduit shall be provided if required at site, w/o any extra cost. (iii) In case the wiring is encountered with any beam/column, then the wiring will run on surface to avoid any damage to the RCC portion.

S&F modular switch 230/250 volts grade 6 Amp rating one way (as catered in point wiring above) complete all as specified and as directed.

All as per Srl item No.60 above, but SP 16 Amp rating.

S&F modular socket 5 Pin 6 Amp multipurpose type out let shuttered type flush mounting type, 230/250 volts grade (as catered in point wiring above) complete all as specified and as directed.

All as per Srl item No.62 above, but 6 Pin 16 Amp multipurpose type.

S&F LED Tube light fitting 10 watt (2 ft) white 230 Volt AC complete including connecting up with three core twisted flexible copper conductorr cable complete all as specified and as directed.

S&F LED Tube Light of 20Watt 230Volt (size 4 ft), box type complete with LED Tube Light 20 Watt & all accessories internally prewired including connecting up with three core sheathed flexible copper conductor cable of suitable size complete all as specified and as directed

S&F cast aluminium housing, powder coated LED bulkheads light fitting 10watts with frosted diffuser complete with suitable driver complete all as specified and as directed.

S&F factory made, sheet steel distribution boards,SPN 4 ways. double door, suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 200 Amps rating copper bus bar complete all as specified and as directed.

S&F MCB SP 6 to 32 Amp "B" curve 10 KA rupturing capacity, IS-8828 marked and fixing in DBs complete all as specified and as directed.

All as per Srl item No.68 above, but MCB SPN 40-63 Amps "C" curve.

M&L for submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x 4 Sqmm drawn in new PVC concealed conduit and its accessories along with 1x4 Sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire duly connected to common earth dolly complete all as specified and as directed.

S&F Metal exhaust fan 250 mm sweep suitable for 240V, 50 Hz single phase AC supply including cutting, chasing for making opening hole of suitable size for fixing on wall with nuts, bolts, washers etc including necessary electrical connection from ceiling rose to fan connecter with three core sheathed wire of required length complete all as specified and as directed. Make:-Crompton/Havells/Bajaj.

Note :- The contract sum shall be after deducting the amount of Sch of Credit shown in Credit Schedule of this Tender.

P R Constructions

Chaudhary Constructions