Balance Work for Construction of Veterinary Dispensary (Single Storey) Telangi at Reckong Peo In District Kinnaur HP(SH-Building Portion thereof ,WS and SI.)

Amount

Filling in plinth with Boulder floor including, watering , ramming consolidating and dressing complete including carriage of material through all modes of transportation with in all leads and lift, as per PWD specifications and as per direction of Engineer in charge.

Providing form work with steel plates 3.15mm. (Three point fifteen milimetre) thick welded with angle iron in frame 30X30mmx5mm.(Thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden/ steel battens and ballies, height of propping and centring below supporting floor to ceiling any floor/height and removal of the same for in situ-reinforced concrete and plain concrete work, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like.

Beams, cantilevers, girders and lintels.

Stair case with sloping orstepped soffits excluding landing.

Edges of slabes and breaks infloors and walls under 20cm width

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge 1:4:8 (One cement : four sand : eight graded stone aggregate 40mm (Forty millimeter) nominal size).including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying upto first floor two level reinforcement cement concrete 1:2:4 (One cement : two sand : four graded stone aggregate 20mm (Twenty millimeter) nominal size) tp give a smooth and even surface including centering and shuttering etc. but excluding cost of rainforcement in Suspended floors roofs, landings and shelves and their supports, balconies beam, girder, bressumers and cantilever , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (One cement : one point five coarse sand) : three graded stone aggregate 20 mm (twenty milimeter nominal size), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Columns, Pillars, Posts and Struts.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like.

Beams, cantilevers, girders and lintels.

Stair case with sloping orstepped soffits excluding landing.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : cement mortar 1:6 (one cement : six coarse sand) : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (seven point five) in superstructure above plinth level up to floor V level. Cement mortar 1:4 (one cement : four coarse sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Random rubble masonry with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm (twenty millimeter) nominal size upto plinth level with : Cement mortar 1:6 (one cement : six coarse sand), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Marble work gang saw cut (polished and machine cut) of thickness 18 mm (eighteen milimeter) for wall lining (veneer work), backing filled with a grout of average 12 mm (twelve milimeter) thick in cement mortar 1:3 (one cement : three coarse sand), including pointing with white cement mortar 1:2 (one white cement : two marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately),, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing Garsa(kullu) stone 12.5mm (twelvepoint five milimeter) cladding on R.C.C. surface side as on faces of Arch masonry walls etc. on 12mm twelve milimeter) Thick cement plaster 1:3 (one cement : three sand) and jointed with cement slurry i/c scaffolding etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) sal wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing 40x3 mm (Forty into three millimeter) flat iron hold fast 40cm. (Forty centimeter) Long including fixing to frame with 10mm (Ten millimeter) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. (Thirty into ten into fifteen centimeter) 1:3:6 (One cement : three sand: six graded stone aggregate 20mm (Twenty millimeter) nominal size), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-incharge. (Note:- But hinges and necessary screws shall be paid separately) , Kiln seasoned and chemically treated deodar wood 40 mm (fory millimeter) thick shutters, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (one point four millimeter) in both directions with wire of dia 0.63 mm (zero point sixty three millimeter), for doors, windows and clerestory windows with hinges and necessary screws: Kiln seasoned and chemically treated deodar wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing Mild Steel grills of required patterns in wood/steel frames of windows etc. M.S. flats, square or round base with round headed bolts and nuts or by screw plain grills in all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete 250x16 mm (two hundred into sixteen millineter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

300x16mm (Three hundred into sixteen millimeter)

250x16 mm (two hundred into sixteen millineter)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than screws etc. complete : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

125mm. (One hundred twenty five millimeter)

100 mm (Hundred millimeter)

75 mm (Seventy five millimeter)

P/F 100mm bright finished brass floor door stopper with rubber cushion screw etc. to suit shutter thickness complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :ncluding carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

300x10 mm (three hundred into ten millimeter )

250x10( two hundred fifty into ten millimeter)

150x10 mm (one hundred into ten millimeter)

Providing and fixing bright finished brass hard drawn hooks and eyes: 150mm (one hundred fifty millimeter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Kota stone flooring(55x55cm) minimum size havinf single shade laid over 20 mm (twenty milimeter) (average) thick base laid over and jointed with cement mortar 1 : 4 (one cement : four coarse sand) : , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Spartic ceremic toilet tile 30x30 cm 10mm thick laid over cement mortar 1:4 including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

6mm thick White glazed tiles dado (30x45cm) in skirting risrs of steps and dado 12mm thick cement morter 1:3(one cement three sand) and jointed with cement slurry including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.ncluding carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

P/L Cement concrete flooring 1:2:4 (One cement : Two coarse sand : Four graded stone aggregate) finished with a floating coat of neat cement,. 40 mm (forty millimeter) thick with 20 mm (twenty millimeter) nominal size stone aggregate, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying 60mm (sisty milimeter) thick faciory made of NTC or its equivalent cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm (fifty milimeter) thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 0.60mm (Zero point sixty millimeter) thick pre-painted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimeter) dia metre with prepainted limpet and rubber washers complete with all accessories as required, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick pre-painted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with pre-painted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.S. BP Sheet 1.66mm (One point sixty six millimeter to 2.00mm (Two millimeter) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured & paid separately) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required: In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

P/F M.S post 10mm Dia (2mm thick shell) in porch including carriage of material through all modes of transportation with in all leads and lift, as per PWD specifications and as per direction of Engineer in charge.

P/F moulded Hand Rail of M.S Hollow pipe 50mm dia welded in straight length over M.S. flat at top of vertical blauster including one coat of red oxide priming coat complete including carriage of material through all modes of transportation with in all leads and lift, as per PWD specifications and as per direction of Engineer in charge.

Painting two coats(excluding priming coat)on new steel based surface with enamel paint to give an even shade including cleaning the surface of dirt dust and other foreign matter sand papering and stoping with enamel paint other than white as per direction of Engineer-In-Charge including carriage of materials with in all leads and lifts including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Painting two coats(excluding priming coat)on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt dust and other foreign matter sand papering and stoping with enamel paint other than white as per direction of Engineer-In-Charge including carriage of materials with in all leads and liftsincluding carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm cement plaster in single coat on fair side of brick/concrete /stone walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and /or rounded angles not exceeding 80mm in girth and finished even and smooth cement mortar 1:6(one cement:: four sand). including carriage of materials with in all leads and lifts including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm cement plaster in single coat on rough side of brick/concrete /stone walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and /or rounded angles not exceeding 80mm in girth and finished even and smooth cement mortar 1:6(one cement:: four sand). including carriage of materials with in all leads and lifts including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

6mm(six millimeters) cement plaster to ceiling 1:3 (one cement :three sand) including carriage of material through all modes of transportation with in all leads and lift, as per PWD specifications and as per direction of Engineer in charge. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

finishing Wall with 100% premium acrylic emulsio paint having VOC less than including carriage of material through all modes of transportation with in all leads and lift, as per PWD specifications and as per direction of Engineer in charge.

Painting with synthetic enamel paint of approved brand and manufacture to including carriage of material through all modes of transportation with in all leads and lift, as per PWD specifications and as per direction of Engineer in charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture of and of required shade of undecorated wall surfces to give an even shade over and including a priming coat with Alkali-resistance primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth including carriage of materials with in all leads and lifts including carriage of material through all modes of transportation with in all leads and lift, as per PWD specifications and as per direction of Engineer in charge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. including carriage of material through all modes of transportation with in all leads and lift, as per PWD specifications and as per direction of Engineer in charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. including carriage of material through all modes of transportation with in all leads and lift, as per PWD specifications and as per direction of Engineer in charge.

Constructing course rubble hammer dressed 'U' shape open surface drain with side wall 15 x 22 cm(fifteen into twenty two millimeter) in cement mortar 1:6 ( one cement :six sand ) and inside plastering with cement plaster 1 :3 (one cement :three sand ) including earth work and laying 10 cm(ten centimetre) cement concrete in 1:5:10 ( one Cement : Five sand : ten graded stone aggregate of 40 mm (forty milimetre)nominal size) and 7.5 cm (seven point five centimeter) cement concrete 1:2:4 (one: cement :two sand :four graded stone aggregate of 20 mm (twenty milimetre) nominal size ) and finished with a floating coat of neat cement complete as per standard design including carriage of material and other incidentials in all leads and lifts and as per the direction of the Engineer-in Charge including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Constructing manhole with R.C.C. top slab in 1;2;4 mix in (one cement;two sand:four graded stone aggregate 20mm(twenty millimetres) nominal size)foundation concrete 1:4:8(one cement: four sand:eight graded crushed stone aggregate 40mm(forty millimetres) nominal size)inside plastering 15mm (fifteen millimetres)thick with cement mortar 1:3(one cement:three sand) finished with a floaing coat of neat cement and making channels in cement concrete 1:2:4 mix (one cement two sand:four graded crushed stone aggregate 20mm(twenty millimetres) nominal size) finished smooth complete including curing and testing inside size 800mmx800mm(eight hundred x eight hundred millimetres) and 500mm(five millimeters) deep including C.I.cover wih:frame(Light duty single seal:patteran 1)455mmx610mm (four hundred fifty five x six hundred ten millimetres)internal dimensions total weight of cover and frame to be not less than 38 kg.(thirty eight kilograms)weight of cover 23 kg (twenty three kilograms)and weight of frame15 Kg.(fifteen kilograms)with 300mm(three hundred millimetres) thick walls of squared rubber masonry coursed with hard stones of approved quality in cement mortar 1;3(one cement:three sand) including carriage of materials within all leads lifts.including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floor, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing 100mm dia “P” or “S” trap for water closet squatting pan)including jointing the trap with the pan and soil pipe in cement mortar 1:1(one cement:one sand)cast iron. including carriage of materials within all leads lifts.including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

P/F viterous china wash basin no.10001 of hindware or its equivalent with single hole for piller tap wth CI or M.S brackets painted white including cutting holes and making good the same but excludings fittings, 51.1) Flat back 630*450mm ,including carriage of material through all modes of transportation with in all leads and lift, as per PWD specifications and as per direction of Engineer in charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fitting. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass chain and rubber plug complete for sink or wash basin: 32 mm dia (thirty two millimeter diameter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass waste for wash basin or sink including all lead and lift: 32 mm dia (thirty two millimeter diameter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.I. Union for wash basin or sink including cutting and threading the pipe and making long screws etc. complete (New work) 32 mm dia (Thirty two millimeter diameter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing CP Brass 32mm (thirty two millimeter) size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 100mm (Hundred milimeter) sand cast iron grating for gully trap, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 600x450mm (six hundred into four hundred fifty millimeter) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimeter) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour, 600 mm (six hundred millimeter) long towel rail with total length of 645 mm (six hundred forty five millimeter), width 78 mm (seventy eight millimeter) and effective height of 88 mm (eighty eight millimeter), weighing not less than 190 gms (one hundred nintey grames), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm (one hundred thirty eight millimeter) , breadth 102mm (one hundred two millimeter), height of 75mm (seventy five millimeter) with concealed fitting arrangements, weighing not less than 106 gms (one hundred six grames), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P brass bib tap with capstan head ISI marked Nos. I.S. 8931 & 8934 with capstan head. 15mm (Fifteen millimeter) diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass pillar tap with capstan head 15mm (Fifteen millimeter) diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing brass stop cock of approved quality : 15 mm (fifteen millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing uplasticised PVC connection pipe with brass unions : 30cm (thirty centimeter) length, 15 mm (fifteen millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge, Concealed work, including cutting chases and making good the wall etc., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

16 mm dia (sixteen milimeter diameter)

20 mm dia (twenty milimeter diameter)

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm (fifteen milimeter) nominal bore ball valve and mosquito proof PVC cover with inter locking arrangement including hoisting upto all heights above ground leval. 1000 litre capacity, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PVC floor trap of self cleansing design with fixing with approved adhesive, cost of cutting and making good the wall and floors etc., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PVC soil, waste and ventilators pipes, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

75mm (seventy five millimeter)

150mm (One hundred fifty millimeter)

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm (three milimeter) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

75 mm (Seventy five millimeter)

100 mm (One hundred millimeter)

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

75 mm (Seventy five millimeter)

100 mm (One hundred millimeter)

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

75 mm (Seventy five millimeter)

100 mm (One hundred millimeter)

Providing and fixing S.C.I. S&S, Slotted Cowl (Terminal guard), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

100 mm (One hundred millimeter)

75 mm (Seventy five millimeter)

Providing and fixing PTMT Coloured/ White automatic flushing cistern with a pair of PVC/ C.I. or M.S. bracket complete with fittings including PVC symphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same (over flow pipe to be measured and paid for separately). 10 (Ten) litres net capacity. Providing and fixing P.V.C. Cistern 10 (Ten) litres capacity complete in all respect, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains all width, including dressing of sides and ramming of bottoms all lifts, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a all lead: All kind of soil, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

ASHWANI NEGI