SPECIAL REPAIRS TO BLDG NO P 527 and CERTAIN REVENUE WORKS AT PXE CHANDIPUR AND BALASORE UNDER GE I RD CHANDIPUR

Amount

PART-I (PROVISION OF PAVEMENT TILE FLOORING INFRONT OF BLDG NO P/757) M&L 75mm thick PCC 1:3:6 type C2 (40mm graded aggregates) complete all as specified and as directed.

M&L Roughening surfaces of old concrete floor by picking sweeping clean and washing down withs water to remove dust etc and brushing neat cement slurry with 3 kg of cement per square metre complete all as specified and as directed.

M&L for screed bed (or) bedding layer 15mm thick in cm (1:6) for laying floor finish as complete all as specified.

M&L for prepolished pavement tiles of size 467 x 467 x 20/ 300 x 300 x 20 (+/-2mm) mm thick as in footpath & hard standing set in CM (1:6) includung filling joint with white/coloured cement to match complete all as specified & directed.

PART-II (RAISING OF HARD STANDING AND PROVN OF INTERLOCKING PAVER BLOCK NEAR COMMUNITY HALL AT CHANDIPUR) M&L Roughening surfaces of old concrete floor by picking sweeping clean and washing down withs water to remove dust etc and brushing neat cement slurry with 3 kg of cement per square metre complete all as specified and as directed.

M&L 75mm thick PCC 1:2:4 type B2 (40mm graded aggregates) complete all as specified and as directed.

M&L machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60mm thickness M-40 grade with grey cement & pigment complete all as specified and as directed.

M&L sand filling under floor as in interlocking paver block as specified and directed

PART-III (SPECIAL REPAIRS TO BLDG NO P/527) M&L Demolition of cement concrete (Unreinforced) in ground floors and pavings n exc 15cm thickness (Below or above Ground level) complete all as specified and as directed.

M&L Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

M&L for 50mm thick plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in floor and finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick Screed bed or bedding layer for laying floor finishes in CM 1:6 complete all as specified and as directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate to receive tiles complete all as specified and as directed.

M&L for 10mm thick rendering in CM 1:4 on brick or concrete surfaces as in backing coat to receive tile finish as in skirting and dados complete all as specified and as directed.

M&L Vitrified light shade tiles 10mm thick (Square or rectangular) polished, area of each tile not exc 0.36 Sqm in floors etc jointed in neat slurry and pointed in white or coloured cement to match the shade using coloured tiles complete all as specified and as directed.

-Ditto- all as per item No 15 above but as in skirtings.

M & L joint free Glazed ceramic coloured tiles in vertical surface 450 x 350 x 7mm/ 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour tiles complete all as specified and as directed.

M&L joint free Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40 mm graded aggregate complete all as specified and as directed.

M&L for heavy duty outdoor vetrified pavement tiles of size (300 X 300) as in footpath set in CM (1:6) includung filling joint with white/coloured cement to match complete all as specified & directed

M&L Taking down cement plaster any description and the like on brick or stone walls, etc including raking out joints,hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 15mm thick in CM 1:4 rendering on brick or concrete surfaces finished even and smooth with integral water proofing compound (IWPC Measured and paid seperately) on wall complete all as specified and as directed.

M&L Supply only intergral water proofing compound (liquid admixture) complete all as specified and as directed (Makes : pidilite Industries/ Impermo/Snowcem India Ltd/Sika)

M&L for 15mm thick in CM 1:6 rendering on brick or concrete surfaces finished even and smooth without using extra cement on wall complete all as specified and as directed.

M&L for 10mm thick in CM 1:3 rendering on brick or concrete surfaces finished even and smooth without using extra cement on ceilings complete all as specified and as directed.

M&L for three coats of white wash as in ceilings on newly plastered surfaces including preperation complete all as specified and as directed.

M&L for preparation of old decorated surfaces of ceiling plastered or unplastered incl removing cornices, pilasters by brooming down to remove all dust, dirt and all loose scales and other foreign matter and smoke soot, moulds, moss and efflorescent salt, oil & grease spots by steel wire brushes or steel scrapers, etc and applying one coat of white wash toceilings to obtain uniform surface including making good the surface all as specified.

---dito as per item No 27 above but in walls

M&L for prepartion of newly plastered surfaces and priming plastered surfaces with alkaliresistant primer paint and applying two coats of oil bound distemper on walls.

M&L complete removal of existing treatment and chalk whiting, on plastered surfaces, preparatory to distempering and applying two coat of distemper oil emulsion including making good the surface all as specified.

M&L complete removal of existing treatment and applying two coat of exterior emulsion paint on external wall surface over a coat of primer over a coat as directed by Engr-in-charge

Taking up or down steel tubing 15mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

Taking up or down steel tubing 20mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed.

S&F GI pipe medium grade 15 mm dia bore as in walls complete all as specified and as directed.

S&F GI pipe medium grade 20 mm dia bore as in walls complete all as specified and as directed.

S&F Fixing only, GI pipe medium grade 15 mm dia bore, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F vitreous china urinal half stall type white(excluding flushing cistern (including flush pipe & Waste coupling) complete including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe complete all as specified and as directed.

Supply and fix PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe in repairs complete all as specified and as directed.

Supply and fix PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F vitreous china wash basin, white, flat back size 550x400mm, incl cutting for and pinning in ends of brackets and waste coupling in repairs complete all as specified and as directed.

Supply only pillar taps, cast copper alloy, fancy type, chromium plated, screwed down high presure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed in repairs complete all as specified and as directed.

S&F PVC waste pipe of size 32mm complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc, from tanks of capacity exc 250 & n.exc 500 ltr and from mouths of circulating pipes, etc complete all as specified and as directed.

S &F in repairs 15mm CP angular stop cock with flange complete all as specified and as directed. (Make : Prayag cat part No 8310 Brand-waves

S&F in repairs 15 dia fancy type chromium plated bib taps cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe complete all as specified and as directed.

S&F 125mm dia brass chromium plated shower rose with or without swivel joints including fixing to steel pipe or union fixed in repairs complete all as specified and as directed.

S&F of PTMT towel rail 600mm long fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

S&F PVC (SWR) floor trap/nahni trap 75mm dia outlet, plain with grating including jointing with solvent cement in repairs complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/Wall 150mm bore in repairs complete all as specified and as directed.

S&F PVC (SWR) bend of 150mm bore in repairs complete all as specified and as directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 75mm bore in repairs complete all as specified and as directed.

S&F glass shelf assembly consisting of 5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard railing 60 cm long complete all as specified and as directed.

Taking down chowkats or frame n.exc 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as directed by Engineer-in-Charge.

All as per item No.55 above but exc 1.5 Sqm and n.exc 4 Sqm each complete all as specified and as directed.

S&F Anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Anodised aluminium powder coated window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap eading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (3 no.) suitable handle (2no.) complete all as specified

S&F 12 mm thick veneered particle board interior garde , solid core , general purpose type, with face veneers of type BB fixed with screw to timber frame work complete all as specified and as directed.

S&F Anodised aluminium powered coated door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F of factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel moulded both side Prelam PVC sheet strip of 20mm width stuck inside with solvent cement for stiles prelam PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of both side Prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing.

S&F of solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam PVC sheet & edges will be painted to match with prelam sheet reinforced with MS square tube, suppling and fixing in opening as per specification and drawing.

S&F Butt hinges, extruded aluminium alloy with galvanised 100 mm long mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and as directed.

S&F 150mm long extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 150mm long extruded Aluminium anodized barrel tower bolt of extruded section and fixed complete all as specified and as directed.

S&F sheet glass 5.00 mm thick, ordinary quality and glazing with oil putty fixed in square n exc 0.5 Sqm each complete all as specified and as directed.

S&F figured glass 4.00 mm thick, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as directed by Engineer-in-Charge.

S&F Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length 140 mm of cover plate as in repairs complete all as specified and as directed.

S&F stainless steel 20 mm dia curtain rod complete all as specified and as directed.

S&F fancy type stainless steel bracket for 20 mm dia curtain rod complete all as specified and as directed.

PART-IV (Provn of aluminium joinery in Bldg No P/819 at PXE Chandipur) Taking down chowkats or frame n.exc 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as directed by Engineer-in-Charge.

All as per item No.71 above but exc 1.5 Sqm and n.exc 4 Sqm each complete all as specified and as directed.

S&F Anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F 12 mm thick veneered particle board interior garde , solid core , general purpose type, with face veneers of type BB fixed with screw to timber frame work complete all as specified and as directed.

S&F Anodised aluminium powder coated door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F sheet glass 5.00 mm thick, ordinary quality and glazing with oil putty fixed in square n exc 0.5 Sqm each complete all as specified and as directed.

S&F Anodised aluminium power coated sliding window and ventilator shutters, (two Nos of glass & one No of wire mesh) type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as necessary locking system, suitable handle etc and necessary powder coated frame work complete all as specified.

S&F Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length 140 mm of cover plate as in repairs.

PART-V (PROVISION OF SEARCHING CABIN AT MAGAZINE GATE, PXE,CHANDIPUR) M&L Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

M&L Excavation in trenches n.exc 1.50m wide and n. exc 1.50m in depth and getting out soft/loose soil complete all as specified and as directed.

M&L Returnng, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified and as directed.

M&L Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed.

M&L PCC type D2 1:4:8 (40mm graded Aggr) in foundations, filling and mass Conc complete all as specified and as directed.

M&L hardcore of gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface in broken stone or boulders complete all as specified and as directed.

M&L Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and as directed.

M&L Reinforced cement concrete (Nominal mix) Plinth beams type B1 1:2:4 (20 mm graded aggregate) complete all as specified and as directed.

M&L Reinforced cement concrete (Nominal mix) Lintel Bands type B1 1:2:4 (20 mm graded aggregate) complete all as specified and as directed.

M&L Reinforced cement concrete (Nominal mix) Slabs supported on walls type B1 1:2:4 (20 mm graded aggregate) complete all as specified and as directed.

M&L Reinforced cement concrete (Nominal mix) as in Chajjas type B1 1:2:4 (12.5 mm graded aggregate) complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columnshooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or secur;ing with clips complete all as specified and as directed.

All as per item No. 90 above but 5mm dia and over upto and incl 10 mm dia in spacers, stirrups and binders complete all as specified and as directed.

M&L use and waste of form work to sides and soffits of floor or roof beams lintles cantlevers, shelves incl supports etc for rough finished surface of concrete complete all as specified and as directed.

M&L 75mm thick PCC type D-2 1:4:8 (40mm graded aggr) as in sub base of floor complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4 type B-1 (Using 20 mm graded aggregates), in floor and to receive tiles complete all as specified and as directed.

M&L for 15mm thick Screed bed or bedding layer for laying floor finishes in CM 1:6

S&F non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed complete all as specified and as directed.

S&F glazed ceramic coloured tiles of size 300x200x7mm thick for vertical surfaces as in dado/skirtings set and jointed in neat cement slurry and pointed in white or coloured cement to match and over rendering in CM 1:4, 10mm thick complete all as specified and as directed.

M&L for heavy duty pre-polished pavement tiles of size (300 X 300) as in footpath set in cement slurry includung filling joint with white/coloured cement to match complete all as specified & directed

M&L Rendering 15 mm thick cement plaster on internal surfaces of brick work in CM 1:6 andn surface to be finished even & smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick in CM 1:4 rendering on brick or concrete surfaces finished even and smooth (without using extra cement) with IWPC (IWPC measured and paid separately) complete all as specified and as directed.

M&L Supply only WPC complete all as specified and as directed.

M&L Preparation of new plaster surface of wall and apply two coat of weather coat over a coat of primer over a coat of thin layer of ready made wall putty on external surface complete all as specified and as directed.

M & L applying one coat of thin layer ready made wall putty cutting, rubbing, with sand paper finish smooth and applying two coats acrylic distemper (oil bound distemper) over a coat of wall primer incl preparation of surfaces in new plaster surface complete all as specified and as directed.

M&L 2nd class Hard Wood plain, solid, straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as directed by Engineer-in-Charge.

S&F 30mm thick shutter, 2nd class hard wood glazed, gauged, skeleton shutter, open rebated and prepare to receive glass, gauge etc divided into squares edges of framing, plain, chamfered or rounded, mitred and rebated sash bars any numbers prepared to receive glass/ gauge and all as specified.

S&F 35 mm thick factory made plain framed panelled shutters (any number of panels), with panels of timber flat on both side (feather edged) or veneered particle board, medium density, wood particle board with commercial face veneers complete all as directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel painting to new wood surfaces over a coat of pink primer including preparation of surfaces area exc 10cm width & girth complete all as specified and as directed.

S&F 150mm long aluminium anodized barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 125mm long aluminium anodized barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F Aluminium alloy anodized handles fabricated type 125 mm long complete all as specified and as directed.

S&F Aluminium alloy anodized handles fabricated type 100 mm long complete all as specified and as directed.

S&F 75mm Butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and as directed.

S&F Butt hinges mild steel 100mm long, medium weight, cooled rolled complete all as specified and as directed.

S&F 250 mm long aluminium anodized alloy sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts etc complete all as directed by Engineer-in-Charge.

S&F Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane of 3.00mm thick complete all as specified and as directed.

S&F 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate ) as in plinth protection finished even aned smooth without usisng extra cement all as specified.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

PART-VI (PROVISION OF X-RAY BAGGAGE SCANNER FACILITY AT MAIN GATE, PXE,CHANDIPUR) M&L Excavation in trenches n.exc 1.50m wide and n. exc 1.50m in depth and getting out soft/loose soil complete all as specified and as directed.

M&L Returnng, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified and as directed.

M&L Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed.

M&L PCC type D2 1:4:8 (40mm graded Aggr) in foundations, filling and mass Conc complete all as specified and as directed.

M&L Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and as directed.

M&L Reinforced cement concrete (Nominal mix) Lintel Bands type B1 1:2:4 (20 mm graded aggregate) complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columnshooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or secur;ing with clips complete all as specified and as directed.

All as per item No. 125 above but 5mm dia and over upto and incl 10 mm dia in spacers, stirrups and binders complete all as specified and as directed.

M&L use and waste of form work to sides and soffits of floor or roof beams lintles cantlevers, shelves incl supports etc for rough finished surface of concrete complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4 type B-1 ( Using 20 mm graded aggregates), in floor and to receive tiles complete all as specified and as directed.

M&L for 15mm thick Screed bed or bedding layer for laying floor finishes in CM 1:6 complete all as specified and as directed.

M&L Vetrified ceramic light shade tiles 10 mm thick area of each tile exc 0.18 sqm not exceeding 0.36 sqm in floors etc set & jointed in neat cement slurry and pointed in coloured cement to match the surfaces complete all as specified and as directed.

All as per item No. 130 above but as in skirtings complete all as specified and as directed.

M&L Rendering 10 mm thick cement plaster on internal surfaces of brick work in CM 1:6 andn surface to be finished even & smooth without using extra cement complete all as specified and as directed.

M&L applying one coat of thin layer ready made wall putty cutting, rubbing, with sand paper finish smooth and applying two coats acrylic distemper (oil bound distemper) over a coat of wall primer incl preparation of surfaces in new plaster surface complete all as specified and as directed.

S&F Anodised aluminium powder coated sliding door shutters with frame & channel ,aluminium section weighing 1.20 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each Shutter, hinges, anodised aluminum snap beading screws etc. complete all as specified

S&F Anodised aluminium powder coated window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified

S&F sheet glass 5.00 mm thick, ordinary quality and glazing with oil putty fixed in square n exc 0.5 Sqm each complete all as specified and as directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length 140 mm of cover plate as in repairs complete all as specified and as directed..

M&L for Anodised aluminium snap grid frame work of size of grid 605 x 605 mm for false ceiling all as specified

S&F 12 mm thick veneered particle board interior garde , solid core , general purpose type, with face veneers of type BB fixed with screw to timber frame work complete all as specified and as directed..

M&L for Non asbestos fibre cement building boards of 4mm thick fixed or laid/ inserted to timber/GI/Aluminiumframeworkwith screws complete all as specified and as directed.

PART-VII (PROVISION OF VECHILE PARKING FACILITY AT FP-II MAIN GATE, PXE CHANDIPUR) M&L Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in Hard/dense soil complete all as specified and as directed.

M&L PCC (1:2:4) Type B2 (using 40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 all as specified & directed

S&F Plates 6mm thick (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment of Fe-410-W(Gde-E-250)quality-A) complete all as specified and as directed

M&L for two coats of synthetic enamel painting to new steel surfaces over a coat of red oxide zinc chrome including preparation of surfaces area exc 10cm width & girth complete all as specified and as directed.

S&F 0.50 mm thick pre painted galvalume aluminiumzinc coating GI based corrugated steel sheet as in roof covering and fixed with self tapping screws as specified.

M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required and similar small articles conforming to Fe-290 Gde-E-165 including necessary bending & welding complete as deiretion & specification

PART-VIII (PROVISION OF ACCESSIBILITY UNDER SUGAMYA BHARAT GUIDELINES AT BALLASTIC CENTRE, AYUDH BHAWAN PWC & IMMG BUILDING AT PXE CHANDIPUR) M&L Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out in soft/loose soil for foundations etc or for manholes etc not exceeding 10 sqm on plan, pipes and poles etc in any location wherever required complete all as specified and as directed

M&L Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.50m above the starting point in soils complete all as specified and as directed.

M&L PCC 1:4:8 type D2 (using 40mm graded stone aggregate in foundation complete all as specified and as directed.

M&L Brick work with sub class B bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed.

M&L Rendering 15 mm thick cement plaster in two coats, 1st coat 10mm thick and 2nd coat 5mm thick on external surfaces of brick work in CM 1:4 including finsingeven and smooth with out usingextracement complete all as specified and as directed.

M&L two coats of cement base paint over a coat of alkali resistant primer on plastered surfaces to wall including preparation of surfaces all as directed by Engineer-in-Charge

M&L for hard core of gauge 63mm but n.exc 10mm deposited spread and leveled in layers complete all as specified and as directed.

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded stone agg as in sub base finished even and rough complete all as specified and as directed.

M&L for 25mm thick PCC (1:2:4) type B1 using 20mm graded stone agg as in floor finished even and smooth using extra cement complete all as specified and as directed.

M&L for heavy duty pre-polished pavement tiles of size (300 x 300 x 10 mm thick) as in footpath set in CM (1:6) includung filling joint with white/coloured cement to match complete all as specified & directed.

S&F stainsteel pipe for railing of 50mm dia 304 grade (Jindal Raw material) including necessary welding complete all as specified

S & F stainless steel base cap of 50mm dia 304 grade (Jindal Raw material) for railing complete all as specified

PART-IX (PROVISION OF LADIES TOILET AT BLDG P/811 AT PXE,CHANDIPUR) M&L Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out complete all as specified and as directed.

M&L Excavation in trenches n.exc 1.50m wide and n. exc 1.50m in depth and getting out soft/loose soil complete all as specified and as directed..

M&L Returnng, filling in including spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified and as directed.

M&L Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed.

M&L PCC type D2 1:4:8 (40mm graded Aggr) in foundations, filling and mass Conc complete all as specified and as directed..

M&L hardcore of gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface in broken stone or boulders complete all as specified and as directed..

M & L for Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and as directed.

M & L for Brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius as Half brick wall built in CM 1:4 complete all as specified and as directed.

M & L for Reinforced cement concrete (Nominal mix) in Plinth beams type B1 1:2:4 (20 mm graded aggregate) complete all as specified and as directed.

M & L for Reinforced cement concrete (Nominal mix) Lintel Bands type B1 1:2:4 (20 mm graded aggregate) complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columnshooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or secur;ing with clips complete all as specified and as directed.

-Ditto- all as per item no 171 above but 5mm dia and over upto and incl 10 mm dia in spacers, stirrups and binders complete all as specified and as directed.

M&L 75mm thick PCC type D-2 1:4:8 (40mm graded aggr) as in sub base of floor complete all as specified and as directed..

M&L 25 mm thick PCC 1:2:4 type B-1 ( Using 20 mm graded aggregates), in floor and to receive tiles complete all as specified and as directed.

S&F non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors etc, and cement screed in CM 1:6, 20 mm thick and jointed in neat cement slurry and pointed complete all as specified and as directed.

S&F glazed ceramic coloured tiles of size 300x200x7mm thick for vertical surfaces as in dado/skirtings set and jointed in neat cement slurry and pointed in white or coloured cement to match and over rendering in CM 1:4, 10mm thick all as specified and directed

M&L Rendering 15 mm thick cement plaster on internal surfaces of brick work in CM 1:6 andn surface to be finished even & smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick in CM 1:4 rendering on brick or concrete surfaces finished even and smooth (without using extra cement) with IWPC (IWPC measured and paid separately) complete all as specified and as directed.

Supply only WPC complete all as specified and as directed.

M&L Three coats of white wash on newly plastered surfaces on wall including preparation complete all as specified and as directed..

M&L Preparation of new plaster surface of wall and apply two coat of weather coat over a coat of primer over a coat of thin layer of ready made wall putty on external surface complete all as specified and as directed..

S&F PVC door frame of standard size and section all as per manufacturer’s instruction complete fixed to brick wall.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frames shall be covered with head moulded plain colour PVC ‘C” channel having a PVC sheet strip of 20mm width struck insi

Butt hinges, extruded aluminium alloy with galvanised 100 mm long mild steel hinge pin, anodised and fixed, type B-21

M&L 2nd class Hard Wood plain, solid, straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as directed by Engineer-in-Charge.

S&F 30mm thick shutter, 2nd class hard wood glazed, gauged, skeleton shutter, open rebated and prepare to receive glass, gauge etc divided into squares edges of framing, plain, chamfered or rounded, mitred and rebated sash bars any numbers prepared to receive glass/ gauge and all as specified.

M&L for two coats of synthetic enamel painting to new wood surfaces over a coat of pink primer including preparation of surfaces area exc 10cm width & girth complete all as specified and as directed.

S&F 150mm long aluminium anodized barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 125mm long aluminium anodized barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F Aluminium alloy anodized handles fabricated type 125 mm long complete all as specified and as directed.

S&F Aluminium alloy anodized handles fabricated type 100 mm long complete all as specified and as directed.

S&F 75mm Butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and as directed.

S&F 200mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane of 3.00mm thick complete all as specified and as directed.

S&F Sheet glass Figured glass, pin head type in squre n.exc. 0.5Sqm in each pane of 3.00mm thick complete all as specified and as directed.

S&F 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate ) as in plinth protection finished even aned smooth without usisng extra cement all as specified.

M&L for vitreous china squatting pan of Orissa pattern size 580 X 440 mm white 'P'trap with intregal foot rest (excluding flushing cystern and flush pipe) in repairs complete all as specified and as directed. . make: Paryware/Hindware

S & F of PVC valveless, syphonic action type, flushing cistern 10 ltr capacity low level white with inlet ball valve float and handle incl brackets incl necessary fittings complete all as specified and as directed..

S&F vitreous china wash basin, white, flat back size 630x450mm, incl cutting for and pinning in ends of brackets or erecting stand but excl taps, pvc conections but incl brackets & Waste Pipe.

S&F 15 mm dia fancy type CP pillar taps, cast copper alloy with capstan head, chromium plated screwed down fixed high pressure, long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F PVC waste pipe of size 32mm complete all as specified and as directed.

S&F glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard railing 60 cm long

S&F for soap container of PTMT fixed with and incl chromium plated brass screws and wooden/plastic cleat complete all as specified and as directed..

S&F aluminium anodised tubular towel rail 20mm dia "D" type 60 cm long between flange complete all as specified and as directed..

S&F 15 mm dia fancy type CP bib taps, cast copper alloy with crutch or butterfly handle, screwed down fixed complete all as specified and as directed.

S&F stop valve 15mm bore cast copper alloy screwed down high pressure fixed to iron pipes or for unions complete all as specified and as directed.

S&F 15 mm size PVC connections with PTMT nuts of length 450 mm complete all as specified and as directed.

S&F CP soap case complete all as specified and as directed.

M&L health faucet Abs with double lock 1.2 meter stainless steel flexible hose and wall hook complete all as specified and as directed.

S & F 110 MM PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S & F 110 x 75 mm PVC (SWR) reducer complete all as specified and as directed.

S & F 110 mm PVC (SWR) bends complete all as specified and as directed.

S & F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F 75mm PVC (SWR) vent cowl complete all as specified and as directed.

PVC (SWR) floor trap 75mm dia, plain with gratings including jointing with solvent cement complete all as specified and as directed.

PVC (SWR) Gully trap 125/110 mm , setting and jointing with solvent cement complete all as specified and as directed.

S&F Rotational moulded polyethylene water storage tanks triple layer in white colour (cylin-drical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 500 litre complete all as specified and as directed.

S/F PVC ball valves high pressure with polythene float and fly nut complete, screwed for iron pipe of 20mm bore in repair ( PRAYAG).

S&F Gun metal 20 mm bore dia of pipe globe or gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

S&F GI pipes medium grade 15 mm dia with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed..

-ditto- but 20 mm dia complete all as specified

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for Reinforced concrete pipes of dia150mm internal bore, class NP2, laid and jointed complete with collars complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 as concrete bed to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested for CI pipes of 150mm bore complete all as specified.

M&L Soakage wells o size 1.8 M dia X 4.5 M effective depth, excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats complete all as specified and as directed.

PART-X (PROVISION OF SOLAR SECURITY LIGHTS FROM BLOCK NO-51 TO SHOPPING COMPLEX AT DEFENCE COLONY BALASORE) Supply and fixing solar street light Integrated lithium Battery led street light - 40Watt LED light with 12.8V,32AH , Lithium ion cell with solar PV module of 150 watt polycrystalline and MS powder coated pole 7mtr hight with other accessories as per techanical specification & manufacturers instructions as below Make: TATA/PHILIPS or equivalent A basic solar powered LED street light system components are :- 1. Solar panel or photovoltaic module. 2. Lighting fixture -LED lamp set. 3. Rechargeable Deep Cycle Lithium lon Battery. 4. Inbuilt Solar Charge Controller. 5. Light Pole.

TECHNICAL SPECIFICATION : LED light Make - SUNLIGHT SOLAR Power - 40 Watt Battery Size - 12.8 Volt, 32AH, Inbuilt Li-ion Battery with 16-18 hour autonomy Driver Efficiency - >85% Net Power Consumption - 40+-10%W Led Luminous Efficacy - >=135lm/W Led Beam Angle -185* Housing/ casing Type - Aluminium Pressure Die Cast Features - Automatic Dusk to Dawn Operation with Power Saving Mode ; Battery Over Voltage &low Voltage Protection. Working Life - >50000Hrs. Ip Rating - IP 65 Warranty - 2years Solar PV module Make - SUNLIGHT SOLAR Maximum power - 150watt Voltage at Max. power - 17.84 V Current at Max. power - 8.41 A Open circuit Voltage - 22.58 V Short Ciruit Current 8.70 A Performance Warranty - Linear Power Warranty For 25 Years

PART-XI (PROVISION OF SHED NEAR BLDG NO P/50 AT DEFENCE COLONY BALASORE) Excavation in post holes (or similar holes) each N.exc 0.5 cum getting out in soft soil , returning filling in and ramming earth or broken rubble mixedwith earth around in layers n.exc 25cm, watering and removing surplus soil to a distance n.exc 50m and making good the surface complete all as specified and as directed..

Material and labour for PCC (1:3:6) type C-2, (using 40mm graded aggregate) as in foundation, mass fillings for embedding struts etc. complete all as directed.

S&F for MS rolled section, roof trusses (framed), trussed, purlins, rafters, plates, cleats and fastenings and heavy bracket framing (beam, tee, angle channel or flat sections) of Fe-410 -W(Gde E-250) quality-B etc complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coting GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F 0.50 mm thick pre painted galvalume aluminiumzinc coating GI based plain steel sheet as in roof covering and fixed with self tapping screws as specified.

Material and labour for preparation of steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed.

Ajay Associates

ELECTRO COMMERCIAL CO

RANA ENTERPRISES

M/S T.N.CONSTRUCTION

DS ENTERPRISES

MS VIDYANJALI