Repair and Renovation Works of Vikram Dev University, Jeypore, Koraput, Odisha.

Grand Total 3,78,76,897.07

Administrative Building - 1 cum 250.43 326.73 81,823.04

Administrative Building - 1 cum 57.33 357.88 20,517.39

Filling in foundation, trenches and plinth with river sand, well watered and

compacted in layers of 1.8 mtr, with top surface dressed and leveled to proper

gradient including cost of all materials, conveyance, all taxes and royalties,

11 loading and unloading, including cost of all labour, sundries, T & P etc. All

complete as per directions of the Engineer -in-charge.

Commerce Block (Faculty Office) cum 2.31 2,349.71 5,427.83

Administrative Building - 1 cum 11.67 2,349.71 27,421.12

Filling available excavated earth (excluding rock) in trenches plinth sides of

foundation etc. in layers not exceeding 20 cm in depth, consolidating each

12 deposited layers by ramming and watering, lead up to 50m and lift up to 1.5 mt

etc. including cost of all labour, sundries T & P etc complete in all respect as

per the direction of Engineer-In-Charge. -

Administrative Building - 1 cum 153.88 181.52 27,932.21

Digitally signed by JAYA

Cement concrete of proportion (1:3:6) in foundation and floors using 4cm size

clean hard black crusher broken granite stone metal of approved quality and

from approved quarry including hoisting, lowering and laying concrete in layers

not exceeding 15 cm. (6") thick to the required level ramming, watering, curing

13 etc. complete including cost, conveyance, royalties of all materials with all

labour and T&P required for the work etc. complete in all respect and as per the

direction of the Engineer-in-charge.

Commerce Block (Faculty Office) cum 5.47 7,619.26 41,677.35

Administrative Building - 1 cum 8.81 7,619.26 67,125.68

Providing & applying of pre constructional anti-termite treatment by drilling

12mm dia holes at distance of 30cm @ junction of wall & floor about 300mm

apart deep enough to reach the soil below & chemical emulsion

14 (IMIDACHLOPRIED 30.5SC mixed with 47.5ltr water) pumped these holes to

soak the soil @ 1 ltr solution of each hole as per manufactures specification &

the holes should be pluged the filling materials including cost of all materials,

labour, conveyance, T&P, all taxes and hire charges of machinaries as per -

direction of Engineer-in-charge.

Administrative Building - 1 sqm 250.00 123.36 30,839.30

Fly Ash brick masonry in cement mortar (1:6) in Substructure using Fly Ash

bricks of 23 cm. x 11 cm. x 8 cmsize having a crushing strength of not less than

75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular

moulding chamfering and corbelling and similar such type of works with all

necessary projections watering and curing after immersing the bricks in water at

least for six hours before use including cost, conveyance, royalties and taxes of

all materials with all labour,labour cess and T & P required for the work

complete in all respect as per direction of Engineer-in-Charge. -

Administrative Building - 1 sqm 10.69 7,345.13 78,519.48

Providing, lifting, hoisting and laying Reinforced cement concrete of M-25

grade as per approved designs and drawings having a minimum compressive

strength (in work test) 250 Kg. / Square cm. in 15 cm. cubes at 28 days after

mixing and test conducted in accordance with I.S. 516 using 12 mm. to 20 mm.

size black hard crushed broken granite stone chips and screened and washed

sharp sand for mortar of approved quality from approved quarry, washed and

cleaned ( 20mm. size chips not to exceeds 25 %) to be mixed in concrete

mixture with Portland slag cement (PSC) including hoisting, lowering, laying

and compaction concrete by using vibrators, watering and curing for 28 days,

centering and shuttering then after dismantling and removing debris from the

work site and finishing the exposed surface smooth providing grooves or beads

wherever necessary including cost, conveyance, loading, unloading, royalties

and taxes of all materials and cost of all labours, sundries, T & P required of the

work etc.complete in all respect as directed by the Engineer-in-Charge. But

excluding cost and conveyance of M.S. rods or Tor steel and binding wires and

labour charges for straightening, cutting, bending etc. of M.S. rods or tor steel -

tying the grills and

Administrative placing

Building - 1in proper position. -

Foundation and plinth cum 12.00 8,552.53 1,02,630.41

Column upto plinth cum 6.85 8,552.53 58,584.86

Plinth beam cum 8.99 9,579.54 86,120.02

Ground Floor -

Lintel for openings cum 2.48 17,595.19 43,636.08

Lintel for openings cum 3.94 19,047.94 75,048.87

Supplying Cutting, straightening coiled or bent up M.S. Rod or tor steel of

primary steel producers such as SAIL / Tiscon / RINL / JINDAL STEEL /

SHYAM STEEL (grade Fe-500D) etc. including bending, binding, welding and

jointing if necessary and tying the grills and placing in position as required for

R.C.C. Work and for providing fan hooks as required, hoisting, lowering, laying

including cost, conveyances, taxes of M.S. Rod or tor steel and binding wires of

18 to 20 gauge and labour required for the work for bending, binding and tying

the grills in all floors with labour cess etc. (payment will be made on standard

weight of B.I.S. for M.S. Rods or tor steel only) etc. complete as per

specification & direction of Engineer-in-charge. - -

Administrative Building - 1 -

Ground Floor Qntl 17.50 11,213.75 1,96,240.67

Digitally signed by JAYA

Fly Ash brick masonry in cement mortar (1:6) in super structure using Fly Ash

bricks of 25 cm. x 12 cm. x 8 cm size having a crushing strength of not less than

75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular

moulding chamfering and corbelling and similar such type of works with all

18 necessary projections watering and curing after immersing the bricks in water at

least for six hours before use including cost, conveyance, royalties and taxes of

all materials with all labour,labour cess and T & P required for the work

complete in all respect as per direction of Engineer-in-Charge. -

Administrative Building - 1 cum 10.40 8,436.16 87,693.91

Administrative Building - 2 (Dewan Bungalow) cum 24.50 8,436.16 2,06,685.97

Administrative Building - 1 0

Providing 16 mm thick cement plaster with cement mortar of mix (1:6) with

screened and washed sharp sand for mortar and finished smooth to the rough

surface of walls in all heights after racking out joints including watering and

19 curing, rounding of corners, providing grooves where ever necessary with cost,

conveyance, royalties of all materials with cost of all labour,labour cess, T&P,

and scaffolding required for the work etc. complete in all respect as directed by

the Engineer in charge. -

Administrative Building - 2 (Dewan Bungalow) sqm 726.00 349.21 2,53,525.88

Administrative Building - 1 -

Ground Floor sqm 396.00 349.21 1,38,286.84

Providing 12 mm thick cement plaster with cement mortar of mix (1:6) with

screened and washed sharp sand for mortar and finished smooth to the rough

surface of walls in all heights after racking out joints including watering and

20 curing, rounding of corners, providing grooves where ever necessary with cost,

conveyance, royalties of all materials with cost of all labour,labour cess, T&P,

and scaffolding required for the work etc. complete in all respect as directed by

the Engineer in charge. - -

Administrative Building - 2 (Dewan Bungalow) sqm 1638.00 245.46 4,02,069.38

Administrative Building - 1 -

Ground Floor sqm 482.58 245.46 1,18,455.82

First Floor sqm 136.08 250.97 34,152.57

6 mm thick cement plaster (1:4) to RCC surfaces finished smooth including

closed deep chiping and slury treatment. in Ground Floor - -

Administrative Building - 2 (Dewan Bungalow) sqm 650.00 261.11 1,69,721.76

Administrative Building - 1 -

Ground Floor sqm 915.05 261.11 2,38,929.07

Providing and laying vitrified tiles 600mmx1200mm (thickness to be specified

by the manufacturer), with water absorption less than 0.08% and conforming to

IS: 15622, of approved brand & manufacturer, in all colours and shade, in

skirting, riser of steps, laid with cement based high polymer modified quick set

22 tile adhesive (water based) conforming to IS: 15477, in average 6 mm

thickness, including grouting of joints (Payment for grouting of joints to be

made separately). DAR 2023 Vol.I, Cl 11.47.4 Pg.835

Administrative Building - 1 sqm 315.00 1,519.96 4,78,786.77

Providing, fitting, fixing vitrified tiles of premium grade having thickness 8mm

to 10mm confirming to IS 13756 of size 600mm x 600mm Plain (Ivory) of

approved make as directed by Engineer-in-charge in dados skirting and risers of

23 steps on 12mm thick cement plaster (1:3) jointed with neat cement slurry mixed

with pigment to match the shades of the tiles including rubbing and polishing

etc. complete with cost, conveyance, royalties of all materials all labour,labour

cess complete in all respects. -

Administrative Building - 1 sqm 12.60 1,521.88 19,175.71

Supplying, fitting and fixing vetrified Industrial tiles in floors of premium grade

having thickness 8mm to 10mm of size 300mm x 300mm confirming to IS

24 4457 with colour/ printed series of approved make on 20mm thick bed of C.M.

(1:4) including cost of all materials, labour, T&P etc. required for the work in

all respect as directed by the Engineer in charge. -

Commerce Block (Faculty Office) sqm 33.07 1,317.12 43,557.03

25 Chequered tile -

Commerce Block (Faculty Office) sqm 12.90 1,453.76 18,752.41

Supplying of Antiskid Ceramic Floor Tiles in flooring using special plain /

printed series Ceramic Floor Tile of premium grade (having minimum thickness

7 mm to 8 mm & size 300 mm x 300 mm, confirming to I.S 13755 of approved

quality and shade of approved make as directed by Engineer-in-charge in floors,

treads on steps and landings on 20 m.m thick bed of cement mortar of mix (1:4)

laid in proper slope and gradient with screened & washed sharp river sand for

mortar and fixing with neat white cement slurry, grouting the joints with neat

white cement slurry mixed with required quantities of pigments (Tiles are to be

immersed in the water for required time before use) of approved make to match

the shades of the Ceramic Floor Tiles - -

Administrative Building - 2 (Dewan Bungalow) sqm 163.80 1,640.75 2,68,755.60

Administrative Building - 1 -

Digitally signed by JAYA

Ground Floor sqm 20.32 1,640.75 33,336.03

Supplying of 300 x 600 special plain/printed series Ceramic wall tiles of

premium grade having thickness 6.5mm to 6.7mm confirming to IS 13753 of

approved make as directed by Engineer-in-charge in dados on 12mm thick

27 cement plaster (1:3) jointed with neat cement slurry mixed with pigment to

match the shades of the tiles including rubbing and polishing etc. complete with

cost, conveyance, royalties of all materials all labour,labour cess complete in all - -

Administrative Building - 2 (Dewan Bungalow) sqm 176.40 1,561.19 2,75,393.42

Administrative Building - 1 -

Fixing granite tiles of approved dimension area above 0.4 sqm (20mm thick) in

floor, treads of steps and landing on 20mm thick bed of cement mortar (1:4)

28 jointed with neat cement slurry mixed with pigment to match the shades of the

tiles including rubbing and polishing etc. complete with cost, conveyance,

royalties of all materials complete in all respects as per direction of Engineer-in- -

Administrative Building - 2 (Dewan Bungalow) sqm 77.11 3,357.47 2,58,900.90

Fixing granite tiles of approved dimension area above 0.4 sqm (20mm thick) in

Dados, treads of steps and landing on 12mm thick cement mortar (1:3) jointed

29 with neat cement slurry mixed with pigment to match the shades of the tiles

including rubbing and polishing etc. complete with cost, conveyance, royalties

and taxes of all materials complete in all respects as per direction of Engineer-in- -

Administrative Building - 2 (Dewan Bungalow) sqm 12.98 3,506.12 45,502.45

Providing and fixing of UPVC (Un Plasticized Poly Vinyl Chloride)(Make:

Fenstech) Ventilator made out of hollow- chambered UPVC Sections having

isolated drainage and reinforced throughout with galvanized steel. The

ventilator shall be made out of UPVC sections having an overall size of 60mm

x 60mm thickness. Structurally Reinforced with hot dip galvanized up to 50

microns of minimum thickness of 1.2mm with locking system. Prefabricated &

welded through fusion welding the window outer frame & sash shall be fitted

with 5mm thickness Pin-Head glass of reputed brand (Saint Gobain Glass),

weathering sealant & Accessories like louvers made by brand. The outer frame

is to be installed at the side using anchor fastener, Silicon Rubber Sealant. At

least 15 years manufacturing warranty for discoloration, wrapping, mechanical

failures, Shrinkages, Rooting Corrosion etc. with a quality Certificate from

relevant departments of that government through the Dealers including of all

materials and abounds etc. Complete as per directions of Engineer in-charge. -

Commerce Block (Classroom) sqm 2.52 15,131.41 38,131.16

Providing & Fixinng factory made 100% Solid WPC ( Wood Polymer

Composite )- Door Frame 125 mm x 65 mm Single Rebated, made from Wood

Polymer Composite ( Single Extruded Process ) material comparising of virgin

PVC polymer of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and

Natural Fibers ( Wood Powder/ Rice Husk/ Wheat Husk ) and Non toxic

additives fabricated with meter Joints after applying PVC solvent Cement &

screwed with full body treaded star headed screws having minimum frame

31 density of 780 kg/ cbm & an ISO 9001 - 2015 Certified Company, having good

screw holding capacity ( Screw Withdrawal strength of ( Min. 990 N

),Minimum Compressive Strength of 58 N/mm2, Modulus of elasticity

900N/mm2 and resistance to spread of flame of class A category with property

of being termite / borer proof , water / Moisture Proof & Fire retardant & Fixed

in position with SS Dash Fasteners / Hold Fast of reuired dia and lenght, , all as

per specifications drawings as directed by the Engineer-In-Charge. Material test

certificate and authentication should be compulsory provided by the -

Administrative company.

Building - 2 (Dewan Bungalow) rmt 39.60 1,709.34 67,689.71

Administrative Building - 1 -

Ground Floor rmt 24.75 1,709.34 42,306.07

First Floor rmt 9.90 1,709.34 16,922.43

Factory made single leaf Solid WPC (Wood polymer) composite door shutter of

25mm thickcompacted with wood grain finish structural foam panel of 29mm

thickness and a density of 20kg/cu.mtr shall be used as core material for fitting

the metal fittings such as tower bolts, aldrops, handles etc shall be provided. A

structural adhesive compatible with (EPS) foam shall be used for bending the

32 core material, The material and process for manufacturing the door shutters

shall conform to RV-TIFAC composites Design Centre's standards and

specifications and the door shutters Conforming to relevant I.S.specification.

The finish of door shutter will be plain colour white/ Ivory/ Beige/ Light grey/

Mahogany/ Teak wood or any other colour using high quality pigments. Three

heavy whight mild steel butt hinges type-I(ISI marked) size 100mm are to be -

fitted on one side

Administrative of shutter.

Building - 2 (Dewan Bungalow) sqm 12.60 5,667.35 71,408.63

Administrative Building - 1 -

Digitally signed by JAYA

Providing and fixing factory made single extruded WPC (Wood Polymer

Composite) solid door/window / Clerestory windows & other Frames/

Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension

Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat

husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)

fabricated with miter joints after applying PVC solvent cement and screwed

with full body threaded star headed SS screws having minimum frame density

of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),

minimum compressive strength of 58 N/mm2, modulus of elasticity 900

N/mm2 and resistance to spread of flame of Class A category with property of

being termite/borer proof, water/moisture proof and fire retardant and fixed in

position with M.S hold fast/lugs/SS dash fasteners of required dia and length

complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS

dash fasteners shall be paid for separately). Frame size 65 x 125mm (DSR- Cl. -

Administrative Building - 2 (Dewan Bungalow) sqm 19.50 1,381.60 26,941.20

Supplying, fitting and fixing of 32mm thick flush door shutter with approved

quality of 30mm thick BWR block board pasted with 1mm thick sunmica on

34 both side of approved design and quality including cost of all door fittings and

fixtures etc. complete. SOR 2022 P-234 Sl No-8

Administrative Building - 2 (Dewan Bungalow) sqm 6.48 15,181.18 98,374.07

Providing and fixing factory made uPVC white colour sliding glazed window

upto 1.50 m in height dimension comprising of uPVC multi-chambered frame

with in-built roller track and sash extruded profiles duly reinforced with 1.60 ±

0.2 mm thick galvanized mild steel section made from roll forming process of

required length (shape & size according to uPVC profile), appropriate

dimension of uPVC extruded glazing beads and uPVC extruded interlocks,

EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with

hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40

35 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and

necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut

and fusion welded at all corners, including drilling of holes for fixing

hardware's and drainage of water etc. After fixing frame the gap between frame

and adjacent finished wall shall be filled with weather proof silicon sealent over

backer rod of required size and of approved quality, all complete as per

approved drawing & direction of Engineer-in-Charge. (Single / double glass

panes, wire mesh and silicon sealent shall be paid separately). Variation in

profile dimension in higher side shall be accepted but no extra payment on this - -

account shallthree

Three track be made.

panels(DAR 2021

sliding vol-Iwith

window Clause No-9.147.D,

fly proof S.S wirepgmesh

glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm &

sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing

bead / double glazing bead of appropriate dimension. (Area of window above

1.75 sqm). (DAR 2021 vol-I Clause No-9.147D.4, pg no.518) -

Administrative Building - 2 (Dewan Bungalow) sqm 12.96 9,877.77 1,28,015.88

Administrative Building - 1 -

Ground Floor sqm 3.24 9,877.77 32,003.97

First Floor sqm 3.24 9,877.77 32,003.97

Providing and fixing of UPVC (Un Plasticized Poly Vinyl Chloride) Ventilator

made out of hollow- chambered UPVC Sections having isolated drainage and

reinforced throughout with galvanized steel. The ventilator shall be made out of

UPVC sections having an overall size of 60mm x 60mm thickness. Structurally

Reinforced with hot dip galvanized up to 50 microns of minimum thickness of

1.2mm with locking system. Prefabricated & welded through fusion welding

36 the window outer frame & sash shall be fitted with 5mm thickness Pin-Head

glass of reputed brand (Saint Gobain Glass), weathering sealant & Accessories

like louvers made by brand. The outer frame is to be installed at the side using

anchor fastener, Silicon Rubber Sealant. At least 15 years manufacturing

warranty for discoloration, wrapping, mechanical failures, Shrinkages, Rooting

Corrosion etc. with a quality Certificate from relevant departments of that

government through the Dealers including of all materials and abounds etc. - -

Complete as perBuilding

Administrative directions

Engineer in-charge.

Administrative Building - 1 -

Ground Floor sqm 0.72 15,131.41 10,894.62

Supplying and fixing of Roman blinds by fixing powder coated top channel,

37 bottom channel with bottom end cap, control unit and good quality of 1

mm thick fabric with lining of approved design and quality etc. complete. - -

Administrative Building - 2 (Dewan Bungalow) sqm 10.80 6,348.40 68,562.72

Supplying, fitting & fixing in all floors of M.S. grills, grill gates, M.S. gates,

garage door, collapsible gates with top and bottom rails, steel windows, critical

frames for windows, stair case and parapet railing made out of M.S Square bar/

38 flat including stair case hand railing with 40mm. dia G.I.pipe etc. including

painting two coats over a coat of redoxide primer as per approved drawing and

design with cost of all materials & labour, labour cess, T&P, sundries etc.

complete in all respect as per specification & direction of the Engineer-in- -

Commerce Block (Classroom) kg 6417.00 143.10 9,18,263.72

Commerce Block (Faculty Office) kg 42720.00 143.10 61,13,172.19

Administrative Building - 1 kg 51810.00 143.10 74,13,938.47

Digitally signed by JAYA

Painting two coat with approved synthetic enamel paint to new iron work over

a coat of Red oxide primer including cost, conveyances, royalties, taxes of all

materials and cost of all labour with T&P required for the work etc. complete as

per specification & direction of Engineer in charge. -

Commerce Block (Classroom) sqm 40.05 222.67 8,917.77

Commerce Block (Faculty Office) sqm 1708.80 222.67 3,80,491.66

Administrative Building - 2 (Dewan Bungalow) sqm 16.56 222.67 3,687.35

Administrative Building - 1 sqm 2073.82 222.67 4,61,768.09

Priming one coat with wall cement primer (water bound) to make an even

finished surface in all floors and heights to wall surface of approved make and

40 shade including sand papering, applying putty wherever necessary & cost of

scaffolding, staging charges with cost, conveyance, cost of all labour,labour

cess T&P etc. complete as per the direction of the Engineer-in-charge. -

Administrative Building - 2 (Dewan Bungalow) sqm 3014.00 97.47 2,93,768.55

Administrative Building - 1 sqm 3240.76 97.47 3,15,870.40

Finishing surface of walls with cement based wall putty (water based) of

approved make and finished smooth and even surface to receive painting

including cost of scaffolding staging charges with cost of all materials labour T

& P etc. as per direction of Engineer -In -charge. -

Commerce Block (Classroom) sqm 363.00 109.39 39,707.12

Commerce Block (Faculty Office) sqm 1665.99 109.39 1,82,235.98

Administrative Building - 2 (Dewan Bungalow) sqm 3014.00 109.39 3,29,689.40

Administrative Building - 1 sqm 3240.76 109.39 3,54,493.77

Painting two coats with plastic emulsion paint with a approved quality primer

to make an even finished surface in all floors and heights to wall surface of

42 approved make and shade including sand papering, applying putty wherever

necessary & cost of scaffolding, staging charges with cost, conveyance, cost of

all labour, labour cess, T&P etc. complete as per the direction of the Engineer- -

Commerce Block (Classroom) sqm 362.50 128.54 46,594.81

Commerce Block (Faculty Office) sqm 1665.99 128.54 2,14,142.02

Administrative Building - 2 (Dewan Bungalow) sqm 3014.00 128.54 3,87,411.72

Administrative Building - 1 sqm 3240.76 128.54 4,16,558.86

Providing and fixing of BMI MONIER / KORAMIC European clay roof Tiles

with minimum pitch 20 degree slope roof, Initial emittance > 0.75 on

waterproof and sloped surface of terrace, laid on 20 mm thick cement sand

mortar in the ratio of 1:3 (1 cement: 3coarse sand), batten ready width of 352

43 mm center to center distance. Clay roof tile fixing dry process and top part use

ridge cover etc including cost of conveyance, cost of all materials, all taxes,

labour, T&P etc. complete as per direction of the Engineer‐in‐charge.

Roman clay roof tile, natural red/antique. Minimum pitch 20 degree slope roof,

make BMI MONIER -

Commerce Block (Faculty Office) -

Entrance Slab sqm 975.00 4,630.32 45,14,562.00

Instalation of tiles sqm 975.00 856.68 8,35,263.00

Construction of granular sub-base by providing Close graded Granular subbase

Grading-III material as per table 400-1, spreading in uniform layers with motor

44 grader on prepared surface, mixing by mix in place method with rotavator at

OMC, and compacting with vibratory roller to achieve the desired density

complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge -

works (4th Revision)

Commerce Block (Faculty Office) sqm 22.50 2,605.53 58,624.34

Supplying and fixing of 60mm thick cement concrete interlocking paver block

of M-30 grade of approved make, design, colour and size made by Block

making machine with proper compaction laid in required pattern etc. complete

in all respect conforming to IRC SP-63:2018..SOR 2022 Sl no-1 P-233 -

Commerce Block (Faculty Office) sqm 100.00 572.63 57,263.04

Supplying and fixing of Pre cast kerb stone of size 300mm x300mm x 150mm

of M-30 grade of approved make, design, colour and size made by Block

46 making machine with proper compaction fixed in required pattern etc. complete

in all respect conforming to IS 5758:1984 (SOR 2022: Page No 233, Item No:

3, New Miscellaneous Items ) -

Commerce Block (Faculty Office) nos. 501.00 191.82 96,102.22

Providing corrugated G.S. sheet roofing including vertical / curved surface

fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with

bitumen and G.I. limpet washers or with G.I. limpet washers filled with white

47 lead, including a coat of approved steel primer and two coats of approved paint

on overlapping of sheets complete (up to any pitch in horizontal/ vertical or

curved surfaces), excluding the cost of purlins, rafters and trusses and including

cutting to size and shape wherever required..DSR 2023 P-186 Sl no-12.1.2 -

Commerce Block (Classroom) sqm 300.00 1,257.55 3,77,265.00

Commerce Block (Faculty Office) sqm 1439.50 1,257.55 18,10,243.23

Administrative Building - 2 (Dewan Bungalow) sqm 297.00 1,257.55 3,73,492.35

Partition Walling with Alm anodised sec. 9210& 9207 as single groove &

48 double groove respectively as horizontal & vertical member and section 4660 as

tappered clip and jointing angle no 1855 etc with 12mm prelaminated Novapan -

Administrative Building - 2 (Dewan Bungalow) sqm 14.18 4,982.37 70,625.14

49 Wooden paneling -

Administrative Building - 2 (Dewan Bungalow) sqm 13.20 5,310.00 70,092.00

Digitally signed by JAYA

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm

thickness of existing ground prepared with proper level and ramming with tools

wooden (Dhurmos) and than rolling the surface with light roller make the

50 surface smoothen and light waterning with sprinkler and maintenance for 30

days or more till the grass establish properly, as per direction of officer-in-

charge. (REF: Horticulture & Landscaping DSR-2025 , Page no-302 , Seriel -

Commerce Block (Classroom) sqm 500.00 248.67 1,24,336.60

Providing and stacking of Peltophorum species of height 150-165 cm. in big

poly bags of size 25 cm as per direction of the officer-in-charge. -

Commerce Block (Classroom) Each 30.00 248.67 7,460.20

Providing and stacking of Plumeria acutifolia of height 120-135 cm. with 2-3

52 branches in HDPE bag of size 30 cm as per direction of the officer-in-charge -

Commerce Block (Classroom) Each 30.00 115.29 3,458.58

53 Cineraria -

Commerce Block (Classroom) Each 20.00 512.49 10,249.72

54 Dianthus hybrid -

Commerce Block (Classroom) Each 20.00 559.08 11,181.68

Commerce Block (Classroom) Each 20.00 407.65 8,153.09

56 Cosmos hybrid -

Commerce Block (Classroom) Each 20.00 628.94 12,578.80

Electrical Works -

A. Circuit Cum Wiring -

Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FRLS PVC insulated copper conductor of ISI marked with 20

mm dia HMS FRLS PVC conduit ISI marked 6A modular type switch ISI

1 marked and ceiling rose ISI marked of modular type G.I box with metallic

cover plate (both side) of suitable size, modular box with 1.5 sq. Mm FRLS

PVC insulated single core multistandard copper conductor as earth wire

including all accessories and connection as per direction of Engineer -in - -

Supplying & Wiring from first light point to next Light Point (Secondary Point)

with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in

2 surface / recessed 1.6 mm thick PVC conduit and earthing the point with 1.5

sqmm FRLS PVC insulated copper conductor single core cable including

required single rose and Metal box. Nos 6 953.44 5,720.64

Recessed wirring to light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FRLS PVC insulated copper conductor of ISI marked with 20

mm dia HMS FRLS PVC conduit ISI marked 6A modular type 2Way switch

3 ISI marked and ceiling rose ISI marked of modular type G.I box with metallic

cover plate (both side) of suitable size, modular box with 1.5 sq. Mm FRLS

PVC insulated single core multistandard copper conductor as earth wire

including all accessories and connection as per direction of Engineer -in - Nos 2 1,472.64 2,945.28

S/F of 5 step type Modular electronic Fan Regulator ISI Marked with all

connection complete in all respect as per direction of Engineer in charge Nos 10 441.32 4,413.20

Supplying, fixing of 6A switch socket on the same board in existing switch

board with complete fitting by 01 no of 6A switch & socket (modular type) &

5 other required accessories of ISI marked as approved as per direction of Engg. -

in -Charge. (Maximum 02 nos point in one circuit).

Supplying, fixing of 6A switch socket on the separate board with complete

fitting by 01 no of 6A switch & socket (modular type) with suitable size

6 modular box & cover including supplying of all required accessories of ISI

marked as approved as per direction of engg-in-charge.

Supplying, fixing of 2 x 6A switch socket on the separate board with complete

fitting by 02 no of 6A switch & socket (modular type) with suitable size

7 modular box & cover including supplying of all required accessories of ISI

marked as approved as per direction of engg-in-charge.

Supplying,fixing of 1x16A socket on the separate board with complete fitting

by 01 no of 16A switch & socket(modular type) with suitable size modular box

& cover including supplying of all required accessories of ISI marked as

approved as per direction of engg-in-charge. Nos 18 810.66 14,591.88

Supplying and installation of 25A AC starter Modular type, coil voltage-230

9 Volt A.C. on mod Box of suitable size including modular coveras required as

per direction of Engg.-in-Charge . Nos 2 2,655.00 5,310.00

Receass wiring for circuit/submain wiring with the following mentioned size

10 Pvc Frls insulated, copper conductor, single core cable in recessed HMS Frls

Pvc conduit of mentioned size as required as per direction of Engg.-in-Charge. -

2 nos single core 2.5 sq. mm copper wire for phase and neutral and 01 no of

a) single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia

non metallic heavy duty conduit. Mtr 432 204.14 88,188.48

2 nos single core 4 sq. mm copper wire for phase and neutral and 01 no of

b) single core 1.5 sq. mm copper wire for earth continuty conductor in 20 mm dia

non metallic heavy duty conduit. Mtr 270 225.38 60,852.60

Digitally signed by JAYA

2 nos single core 6 sq. mm copper wire for phase and neutral and 01 no of

c) single core 2.5 sq. mm copper wire for earth continuty conductor in 25 mm dia

non metallic heavy duty conduit. Mtr 200 261.96 52,392.00

4 nos single core 10 sq. mm copper wire for phase and neutral and 02 nos of

d) single core 6 sq. mm copper wire for earth continuty conductorin 32 mm dia

non metallic heavy duty conduit. Mtr 300 526.28 1,57,884.00

B. Fan & indoor Fixtures -

Supplying, installation, testing and commissioning following type of light

fixtures with dummy box for surface mounted fixtures only, fans and

11 exhaust fans with all accessories, as required.(The colour temprature for

fixtures shall be above 4000 deg K, CRI Min 80 & white in colour as per

application) -

Supplying and fixing of Energy efficient surface /recess mounted square

/round shape 18 W LED luminaire of dimension of consists of white powder

coated , die-cast Alluminium housing with high quality frosted diffuser for

glare-free uniform lighting distribution with wattage not more than 18 watt and

lumen output of 1800 lumens, , CRI not less than 80,CCT of 6000 degree

K,THD less than 10%, with electronic driver, internal surge protection of 3 KV

, L70 B50: 50000 hrs and all other accessories suitable for operation on 220 V

to 240 V supply as required as per direction of Engg.-in-Charge. Nos 16 1,817.20 29,075.20

Supplying and fixing of Energy efficient surface /recess mounted square

/round shape 12 W LED luminaire of dimension of consists of white powder

coated , die-cast Alluminium housing with high quality frosted diffuser for

glare-free uniform lighting distribution with wattage not more than 12 watt and

lumen output of 1200 lumens, , CRI not less than 80,CCT of 6000 degree

K,THD less than 10%, with electronic driver, internal surge protection of 3 KV

, L70 B50: 50000 hrs and all other accessories suitable for operation on 220 V

to 240 V supply as required as per direction of Engg.-in-Charge. Nos 10 1,416.00 14,160.00

Supplying and fixing of Energy efficient surface /recess mounted square

/round shape 9 W LED luminaire of dimension of consists of white powder

coated , die-cast Alluminium housing with high quality frosted diffuser for

glare-free uniform lighting distribution with wattage not more than 9 watt and

c) lumen output of 900 lumens, , CRI not less than 80,CCT of 6000 degree

K,THD less than 10%, with electronic driver, internal surge protection of 3 KV

, L70 B50: 50000 hrs and all other accessories suitable for operation on 220 V

to 240 V supply as required as per direction of Engg.-in-Charge. Nos 10 1,062.00 10,620.00

SITC of energy efficient LED tube light fittings with decorative alluminium

batten and LED tube light having power rating not more than 20 watt and

lumen output not less than 2000 lumen complete with electronic driver and all

d) other accessories with diffuser having 2 years warranty i/c connection etc as

required as per direction of Engg.-in-Charge.

SITC of Sleek LED 10 watt mirror light fitting with extruded polycarbonate

housing,High optically efficient diffuser,above wash basin complete with all

e) accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS

PVC insulated, copper conductor, single core cable and earthing etc. as required

as per direction of Engg.-in-Charge. Nos 10 868.48 8,684.80

Dia cast Aluminum with Polycarbonate cover IP65 type 1000 Lumen/ 10W

LED Bulkhead wall fitting. Nos 10 1,203.60 12,036.00

S/F of Bakelite angle holder/ batten holder with 9watt Led Bulb of ISI marked

g) conforming to IS-1258/1987 in place of ceiling rose as per direction of Engg.-

Supplying, installation, testing and commssioning of 1200 mm sweep

white/milky colour BLDC ceiling fan with aluminium blades having wattage

not more than 28W and air delivery ≥215m3/min including wiring the down rod

12 of standard length (upto 30 cm) with 1.5 sq mm PVC insulated, copper

conductor, single core cable etc. as required as per direction of Engg.-in-

Charge, Replacement Warranty will be 4 years. (With fan Regulator) Nos 10 4,394.32 43,943.20

Supplying, installation, testing and commissioning of 400 mm sweep wall

mounted fan ISI Marked including earthing etc as required. Nos 6 4,094.60 24,567.60

Supplying, installation, of exhaust fan of heavy duty 300 mm sweep 1400 rpm

14 with louvers of exhaust fan in the existing wall, including fixing & conntection

as required as per direction of Engg.-in-Charge. Replacement Warranty will be Nos 10 3,693.40 36,934.00

Supplying and fixing of following mentioned way, three pole/single pole and

neutral, sheet steel,double door MCB distribution board, 415 volts/240 volts

shall be as per IEC 61439-3,integrated door earthing system offering additional

safety to the user,High quality polyurethane Gasket,the box and cover shall be

15 fabricated to withstand IK09,the DB should be properly pre-treated with 7 tank

process and duly powder coated, phosphatized with powder coated finish, on

surface/recess, complete with terminal blocks,with suitable size FR PVC

insulated copper conducter up to terminal blocks, tinned copper busbar, neutral

busbar, earth bar, din bar. as per direction of Engg.-in-Charge. -

4 Way(8+12) Way TPN MCB DD DB Horizontal Type as per IEC 61439-3

suitable for Flush mounting and Surface mounting with 100A Copper Bus Bar

a) for each phase, with neutral Bus bar, Earth Bar & Cable ties for cable

management, prefitted masking sheet, IP43-IK09 with metal door.

Digitally signed by JAYA

6 Way(8+18) Way TPN MCB DD DB Horizontal Type as per IEC 61439-3

suitable for Flush mounting and Surface mounting with 100A Copper Bus

Bar for each phase, with neutral Bus bar, Earth Bar & Cable ties for cable

management, prefitted masking sheet, IP43-IK09 with metal door. Nos 2 6,218.60 12,437.20

Supplying and fixing following way, horizontal type SPN, sheet steel, MCB

distribution board, 230 V, on surface/ recess, complete with tinned copper bus

bar, neutral bus bar, earth bar, din bar, interconnections, powder painted

16 including earthing etc. as required. (But without MCB/RCCB/Isolator). as per

direction of Engg.-in-Charge. )

Supply and fixing of 12 way DD single pole and neutral sheet steel MCB

distribution board 250V on surface/recess complete with tinned copper bus

bar, neutral bus bar, earth bar, din bar, detachable gland plate,

interconnections, phosphatized and powder painted including earthing etc.

as required (but with out MCB/ RCCB/ Isolator)

Supplying and fixing following rating MCBs/ Isolator in the existing MCB DB

17 complete with connections,testing and commissioning etc. as required. as per

direction of Engg.-in-Charge.) -

Supplying and fixing 63Amps 4P 415 volts MCB in the existing MCB DB

a) in the existing MCB DB complete with connections as per direction of

Engg.-in-Charge. Warranty on MCB is 3 years. Nos 4 3,499.88 13,999.52

Supplying and fixing 63 amps rating, 240 volts, C series,10KA breaking

b) capacity, Double poles MCB of in the existing MCB DB complete with

connections as per direction of Engg.-in-Charge. Nos 2 1,799.50 3,599.00

Supplying and fixing 6-32 Amps rating, C series,10KA breaking

capacity,SP, 230 volts, MCB in the existing MCB DB complete with

connections, testing and commissioning etc. as required as per direction of

Engg.-in-Charge. Nos 76 378.78 28,787.28

Supplying and fixing following rating RCCB/ELCB in the existing MCB DB

18 complete with connections,testing and commissioning etc. as required.

Supplying and fixing 63Amps 4P 415 volts RCCB 30 mA in the existing

a) MCB DB in the existing MCB DB complete with connections as per

direction of Engg.-in-Charge. Nos 4 6,182.02 24,728.08

Supply, fabricating and installing following size of hot dip G.I. perforated type

cables trays including suspending from ceiling with angle, rods connection

19 pieces, horizontal vertical bends, reducers, tees, cross members,G.I. nut bolts,

G.I. washers, fasteners etc. complete as required per specifications & approved

by the Engineer Incharge. -

Supplying,fixing of perforated cable trays with horizental & vertical

bends,reducers ,tees,crossover,brakets & other accessories ar requited

confirming to IS-IEC -61537 ,the cable tray shall be galvanised for corrosion

protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H) x

200mm(W) . The Load bearing capacity of the Cable Trays should be minimum

of 104.8Kg/meter at the span of 1.5Meter as per UL specifications as required Mtr 50 702.10 35,105.00

as per direction of Engg.-in-Charge.

Supplying,fixing of perforated cable trays with horizental & vertical

bends,reducers ,tees,crossover,brakets & other accessories ar requited

confirming to IS-IEC -61537 ,the cable tray shall be galvanised for

b) corrosion protection confirming to DIN EN 10346/ISO 1461. Size 60mm(H)

x 300mm(W).The Load bearing capacity of the Cable Trays should be

minimum of 104.8Kg/meter at the span of 1.5Meter as per UL

specifications as required as per direction of Engg.-in-Charge. Mtr 50 814.20 40,710.00

Supplying,installation,testing & commissioning of materials and installation of

GI earth plate 600mm x 600mm x 6mm thick ISI marked with G. I. nut bolts

& washers including cost of burnt wood charcoal, salt, foreign soil, water

20 pouring arrangements, brick masonary enclosure on top with removable RCC

cover complete with labour for excavation of pit in all kinds of soil & rock as

required and as per direction of Engineer-in-charge.The entire earthing system

should be Replacement Warranty will be 2 years Nos 4 7,670.00 30,680.00

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for

connections etc. as required. Mtr 100 286.74 28,674.00

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop

earthing as required. Mtr 300 83.78 25,134.00

Total Electrical Cost - 7,63,706.62 2,97,643.20

A- Dismantling Item 0

1 Dismantling of G.I. Pipes 0

Dismantling G.I. pipes (external work) including excavation and refilling

trenches after taking out the pipes, manually/ by mechanical means including

stacking of pipes within 50 metres lead as per direction ofEngineer-in-charge Mtr 60.00 190.45 11427.12

2 Dismanteling C.I. Pipes 0.00 0.00

Dismantling C.I. or asbestos pipe with fittings and clamps

including stacking the material within 50 metres lead Mtr 50.00 94.70 4734.75

B- Internal Sanitary & Plumbing System 0 0.00

Digitally signed by JAYA

Supplying all materials, labour, T&P and providing and fixing to wall or ceiling

and floor CPVC pipes conforming to IS:15778 having thermal stability for hot

and cold water supply, including all CPVC plain and brass threaded fittings

3 including fixing the pipe with clamps at 1.00. spacing. This includes Jointing of

pipes & fittings with one step CPVC solvent cement and testing of Joints all

complete as per specification and direction of the Engineer in charge. 0 0.00

In Ground Floor- 0 0.00

20mm dia C-PVC pipe MTR 50.00 370.17 18508.30

25mm dia C-PVC pipe MTR 60.00 489.94 29396.16

Supplying all materials, labour, T&P and providing and fixing to wall or ceiling

and floor pvc pipes conforming to ASTM-D-1785/89 (Sch-80) and pipe fittings

of the following nominal bore with clamps including making good the wall,

ceiling and floor all complete as per specification and direction of the Engineer 0.00 0.00

32mm dia PVC ASTM pipe (sch-80) MTR 50.00 380.08 19003.90

40mm dia PVC ASTM pipe (sch-80) MTR 30.00 499.85 14995.44

Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil

waste ventilating pipes and fittings of the following outside diameter

conforming to ISI No 13592/1992 to walls with nails, bobbins and wooden

plugs or laying in trenches including jointing with supply of approved rubber

lubricant by non-heat application method/as per manufacturer's specification,

testing, earthwork in excavation in all kinds of soil and refilling of trenches ,

cost & conveyance of all materials to worksite, payment of taxes etc. all

complete as per P.H specification and direction of the Engineer-in-charge. 0 0.00

110mm U-PVC SWR Pipe MTR 80.00 607.11 48568.80

80mm U-PVC SWR Pipe MTR 40.00 397.90 15915.84

110mm U-PVC D/Jn door EACH 10.00 650.42 6504.16

110mm U-PVC Plain tee EACH 10.00 455.48 4554.80

110mm U-PVC door bend EACH 10.00 346.45 3464.48

110mm U-PVC Plain bend EACH 15.00 273.76 4106.40

110mm U-PVC ‘P’ Trap EACH 10.00 586.81 5868.14

110mm U-PVC offset without ear EACH 10.00 480.73 4807.32

110mm U-PVC Cowl EACH 10.00 68.68 686.76

110mm U-PVC Socket EACH 10.00 188.92 1889.18

75mm U-PVC Plain tee EACH 8.00 380.79 3046.29

75mm U-PVC Socke EACH 15.00 95.93 1439.01

110mm PVC SWR Clamp/clip EACH 30.00 50.50 1515.12

Supply,Providing, fixing, testing and commissioning in position UV stabilised

110 mm dia PVC Rain water pipe with Fittings (IS: 13592 Type - A). In case of

ceiling hanging, the supply of Pipe Clamps (Chilly/MS angle) as per engineer in

charge.110 mm diameter. 0 0.00

Supply, Providing and fixing 150 mm x 150 mm.dia CI Grating for Rain water

7 pipes 110 mm dia.

150 mm x 150 mm.dia CI Grating EACH 3.00 110.57 331.70

Supplying all materials , labour, T&P and fixing Vitreous china water closet

,squatting pan ( Indian type W.C. pan / Orissa pattern squatting pan ) duly

embedded in cement concrete 1:5:10 using hard granite metal 4cm nominal size

including fixing a pair of vitreous china 250mmx130mmx30mm foot rest,

8 fixing 100mm dia hci 'P' or 'S' trap for water closet squatting pan including

jointing the trap with pan in cement mortar (1:1), cutting the floor and mending

good the damages etc. all complete as per P.H. specification and direction of

Engineer-in-charge. EACH 4.00 4502.29 18009.16

Supplying all materials, labour, T&P and fitting and fixing 10 litres capacity

low level flushing cistern with a pair of cast iron or M.S brackets complete with

fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve

with polythene float CP brass handle, unions and couplings for connection with

9 inlet, outlet and overflow pipes,32mm dia CP flush bend,15mm dia pvc inlet

connection pipe including cutting holes and making good the same and

connecting the flush bend with cistern and closet and connecting the inlet pipe

with supply main etc all complete as per specification and direction of the

Engineer in charge. EACH 12.00 1936.14 23233.73

Supplying all L.L. Cistern

materials, with flush

labour, T&P bend .

and fixing the following vitreous china

Wash Down Water Closet (European type W.C. pan) with integral 'p' or 's' trap

to the floor with wooden plug and chromium plated pedestal screws including

jointing the trap with soil pipe in cement mortar (1:1) fixing plastic seat and

cover for wash down water closet with chromium plated brass hinges and

rubber buffers including polishing , cost & conveyance of all materials to

worksite, payment of royality, taxes etc. all complete as per P.H specification

and direction of the Engineer-in-charge EACH 8.00 3893.65 31149.17

European water closet with 'p' trap plain

Digitally signed by JAYA

Supplying all materials, labour T&P and fixing wash basins with hole for pillar

taps with cast iron or M.S.brackets painted white including cutting holes in

walls and making good the damages with supply of wooden plugs, screws and

cement etc, fixing pedestal for wash basin recessed at the back for the reception

of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for

11 wash basin including brass check nut complete, fixing pillar taps capstan head

screw down high pressure lettered 'Hot' and 'Cold' with long screws, shanks and

back nuts of 15mm dia nominal bore, fixing 15mm dia PVC inlet connection

pipe and making connection with pillar cocks and supply mains for wash basin,

fixing 32mm dia CP brass waste, cost & conveyance of all materials to

worksite, payment of taxes etc. all complete as perP.H specification and 0.00 0.00

direction of the Engineer-in-charge

550mmx400mm Half pedestal wash.basin EACH 6.00 4740.41 28442.48

560mmx450mm size Counter wash basin EACH 4.00 5875.81 23503.24

32mm dia PVC waste pipe with brass coupling nut EACH 10.00 59.59 595.90

Supplying all materials, labour, T&P and fixing bowl pattern urinal conforming

to IS:771-part-3-1985 of the following sizes including connecting the urinal

with 32mm dia pvc waste pipe 910mm long by means of white lead mixed with

12 chopped hemp, fixing 32mm dia CP dome waste, 15mm dia CP spreader

including cutting holes in walls and making good the damages with supply of

wooden plugs, screws and cement etc all complete as per specification and

direction of the Engineer in charge. Half stall urinal EACH 6.00 4071.71 24430.25

15mm dia urinal spreader EACH 6.00 441.44 2648.63

32mm dia C.P. dome waste EACH 6.00 1171.15 7026.90

Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of

13 the following nominal bore with supply of all jointing materials complete as per

specification and direction of the Engineer in charge. 0.00 0.00

15mm dia CP 2way bib cock EACH 12.00 1480.90 17770.80

15mm dia CP Health faucet EACH 12.00 1945.47 23345.59

15mm dia CP Angle stop cock EACH 22.00 1016.33 22359.35

15mm dia CP Pillar cock EACH 10.00 1364.79 13647.88

15mm dia CP Bib cock EACH 4.00 1327.50 5310.00

15mm dia CP extension piece EACH 34.00 62.07 2110.31

PVC Connection Pipe EACH 24.00 40.12 962.88

PVC Discharge Pipe EACH 10.00 59.59 595.90

15mm dia. C.P flange EACH 34.00 91.33 3105.29

125mm dia CP gratting EACH 15.00 102.78 1541.67

25mm dia Brass F.W valve EACH 8.00 1113.21 8905.70

32mm dia Brass F.W valve EACH 6.00 1630.41 9782.44

Supplying all materials,labour,T&P and fixing standard sized Glass-shelf,

Towel Rail, Towel Ring, Soap Holder, Soap dispenser with C.P brass bracket

14 and guard rail complete fixed to wooden pluges with screw etc.all complete as

per specification and direction of Engineer-in-charge.

600mmx125mm size glass shelf with C.P ruard Rail. EACH 10.00 791.19 7911.90

25mmx600mm long CP Towel Rail. EACH 5.00 1068.49 5342.45

CP Towel Ring. EACH 10.00 769.95 7699.50

CP Soap holder EACH 5.00 333.59 1667.93

C P Soap Dispenser. EACH 10.00 303.61 3036.14

Supplying all materials, labour, T&P and fixing of Stainless Steel Coat Hook

alongwith all necessary accessories complete including cutting, making good

the walls, floors, slab wherever complete in all respect as per specification and

direction of the Engineer in charge. 0.00 0.00

Stainless Steel Coat Hook. EACH 12.00 987.31 11847.67

Supplying all materials, labour, T&P and fixing mirror of superior glass

mounted minimum 5mm thick on 6mm thick A.C sheet or plywood sheet and

fixed to wooden plugs with CP screws and washers complete as per

specification an direction of the Engineer in charge. 0 0.00

Single Mirror (Bevelled edge) 600mmx450mm EACH 10.00 948.01 9480.12

Supplying all materials, labour, T&P and providing fitting and fixing (Aqua

guard) Pure Chill 80 PSS UV of size 750x570x1350mm height with water

17 storage capacity 80 liters along with 2 nos of faucets 1 for cold water and 1 for

normal water including a flow of 1.5 ltr per minute etc all complete as per

approved drawing,specification and direction of the Engineer in charge. EACH 2.00 92339.72 184679.44

TOTAL PHE COST- 7,14,266.04 -

Digitally signed by JAYA