Construction of Additional Hospital Building for Government Hospital in Poonamallee Municipality

Amount

Earth work excavation for foundation by Mechanical means for Isolated & Combined Footing etc in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 100 mts and clearing and levelling including dressing of sides and raming of bottoms etc., complete complying with standard specification and as directed by the departmental officers.- Upto 2.40m Footing Depth. - Foundation

Supply and filling in foundation and basement with Gravel in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and providing Anti termite pre construction treatment using aldrin or dealdrin or heptochlor as per relavent IS 6313 (part II) code including cost of all materials, labour, hore charges for T&P etc complete.

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers. -Mixing by manual means

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam, Lintels, Cantilever Beams, Bed Blocks etc.. with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over Steel adjustable Span of Size 2m x 2m(expandable upto 3.60m) and Silver Oak Joists of Size 10 x 5 cm spaced at 50cm to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be rovided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor Slab, Roof Slab, Loft, Landing Slabs, etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25mm x 25mm x 3mm for boarding laid over steel adjustable span of size 2m x 2m (expandable upto 3.60m) and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) , etc complete complying with standard specifications. Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid).

Providing and laying in position, Standardised Concrete Mix M-25 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglm3 and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m’) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials). - BASEMENT

Ground Floor

First Floor

Second Floor

Third Floor

Terrace Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steelreinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire) - BASEMENT

Ground Floor

First Floor

Second Floor

Third Floor

Terrace Floor

Brick work in following Cement Mortar using best quality Burnt Clay Brick of size 9” x 4 3/8” x 2 3/4” with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge - upto basement

Ground Floor

First Floor

Second Floor

Third Floor

Terrace Floor

Brick partition walls of 11.50cm thickness using best quality Burnt Clay Brick of size 9” x 4 3/8” x 2 3/4” with class designation of 7.5 conforming to IS 1077-1992 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately) - First Floor

Second Floor

Third Floor

Paving the floor with best quality vitrified Tiles of following size and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Finishing the top of roof with one course of machine pressed tiles of following size ofapproved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officerr

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used , hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.

Distempering the Two Coats of approved quality including preparation of surface, the rate includes cost of brushes, high scaffolding arrangements, neat finishes, etc., complete complying with standard specification and as directed by the departmental officers.

Painting New Plastered Wall Surface with Two finishing coats of ready mixed (Emulsion) of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete. PWD SOR P.No 98. M-0651

Paving the floor with pre-polished anti-skid Ceramic tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, white / colour glazed tiles conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

Supplying and fixing solid core flush shutter of following type with thickness and necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind appliances and furniture fittings such as 3 Nos of SS 304 Grade Parliament Hinges of Size (125mm x 150mm) , 2 Nos 300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 2 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers - Single leaf.

Supplying and fixing solid core flush shutter of following type with thickness and necessary T.W. internal lipping alround conforming to IS 2202-1(1999) including cost of wind appliances and furniture fittings such as 6 Nos of SS 304 Grade Parliament Hinges of Size (125mm x 150mm), 3 Nos. 300x12mm aluminium tower bolt 1 No. 200x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete complying with standard specification and as directed by the departmental officers -Double leaf.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutterwill be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of Crushed stone sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three Crushed stone sand ) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. Internal Concealed Line 20mm dia

Supplying, laying and jointing PVC pipes (having working pressure 6 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. -25mm dia

75mm dia

Supplying PVC Specials (with working pressure 6kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements - 90 mm Dia Plain Elbow

90 mm Dia Door Elbow

90 mm Dia Plain Tee

Supplying and fixing in position White / Colour Special Delux Model Glazed Cascade Type Parryware / Hindware / Equivalent Wall Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) with 10 litres capacity flushing tank with all internal dual flush fittings with normal seat cover WALL FITTING

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

S/F in position of Indian Make White/Colour glazed earthen ware lipped mouth Flat Back Urinal of best approved quality with G.I.Pipe connection to suitable length,32mm bell mouthed P.V.C connection ,15mm dia G.M.Wheel valve,fixing the urinal to the wall in position with necessary T.W.plugs ,clamps,screws, shellac etc.,including dismantling masonry if necessary and redoing the same to original condition ,fixing the 15mm dia. G.I.pipe connection and wheel valve ,painting the pipe with two coats of approved paint over one coat of primer and checked without any leakage complete, complying with standard specifications. -(D)

Supplying and fixing in position CI.Manhole covers (light or heavy duty) mof various sizes of best approved quality and as per atandard specifications etc.,complete.60 x 60 cm

Supply and delivery and fixing of HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labourcharges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,

Supply and delivery of 2.0 HP Jet Pump Set conforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation.

Supplying and fixing 12" (30cm dia) light duty Exhaust fan including cost of all materials,labour, lead, lift, etc complete (SD -114)

Supply and fixing of 16A DP switch of 500V with matal clad with fuse and neutral (side handle) on suitable TW board with earth connection only etc., complete in all respectes as directed by the departmental officers.(SD-142)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry etc., complete in all respectes as directed by the departmental officers. (SD-233)

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5 metre. etc., complete in all respects as directed by the departemental officers (SD-75)

Supply and fixing of 4 way single phase DB of 16A / way with 16A, DP switch of 500V with metal clad (side handle) with fuse and neutral on suitable TW board with PWD earthing etc., complete in all respects as directed by the departemental officers (SD-151)

Supply and fixing of 5A 3 pin and 2 pin combined flush type wall socket with 5A flush type switch concealed in suitable MS box in flush with wall and concealed with 3mm thick hylem sheet etc., complete in all respects as directed by the departemental officers(SD-135)

Supply and fixing of 5A / 15A 3 pin combined flush type wall socket with 15A flush type switch concealed in suitable MS box in flush with wall and covered with 3mm thick hylem sheet etc., complete as directed by the departmental officers.(SD-138)

Supplying and fixing MCB isolator 32A TP with earth connection (Legrand (MDS/Hager (L & T make) (PWD SOR PG NO:143)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVCrigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour for open PVC light point / fan point (for electronic regulator) (5 points per coil) (SD-18)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitablePVC rigid pipe on wall and ceiling with PVC accessories with TW switch box inflush with wall with 5A FT switch covered with hylum sheet of 3mm thick with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC light point / fan point (for electronic regulator) (SD-19)

Supply and run off 2 of 1.50sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark confirming to IS:694/1990 with continious earth connection by means of 1.50 sqmm PVC insulated single core unsheathed copper conductor cable confirming to IS:694/1990 in suitable PVC rigid pipe 1.8mm thick concealed in wall for mains including the cost of PVC pipes and specials, cables, cement, brass screws, T.W plugs, saddles and labour etc., complete in all respects as directed by the departemental officers.

Supply and run off 2 of 4 sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark confirming to IS:694/1990 with continious earth connection by means of 1.50 sqmm PVC insulated single core unsheathed copper conductor cable confirming to IS:694/1990 in suitable PVC rigid pipe 1.8mm thick concealed in wall for mains including the cost of PVC pipes and specials, cables, cement, brass screws, T.W plugs, saddles and labour etc., complete in all respects as directed by the departemental officers. (SD - 57)

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box on wall with 6A two way module switch with module front plate with continuous earth wire connection of 14 SWG TC wire with painting of Suitable colour for Open PVC Stair case Light point Lower End (SD-340)

Supplying and fixing of 1200 mm (48") AC ceiling fan complete with stepped electronic 300 W regulator with 1 m down rod with fan clamp, side plates and cross arm of size (18") etc., complete as directed by the departmental officers.(SD-106)

Supply and fixing of single box type 4'40 W flu fitting complete with copper choke and condensor with T.W round blocks on wall or ceiling with flu tube with PVC unsheather copper leads from terminals to the filling (SD-88)

Supply and fixing of 18W LED 3000K Square type resessed fiiitng (Philips/Havells) complete with T.W round blocks on wall or ceiling with flu tube with PVC unsheather copper leads from terminals to the filling (PWD SOR P.NO : 121)

Supply and fixing of 25W LED Outdoor street light fitting (Philips/Havells) complete with T.W round blocks on wall or ceiling with flu tube with PVC unsheather copper leads from terminals to the filling (PWD SOR P.NO :122)

Supply and fixing of TNEB meter Board suitable for 32 A Three phase service connection with 32A fuse unit(500V)32A neutral link and earth link (1" x 1/8" Copper flat) on T.W plank of size 600mm x450mm x 19mm with supportingT.W.reepers of 1" thick oneither sider with painting withsuitable bolt and nuts for fixingthe TW plank on wall withearth connection and interconnection with 7/20 PVCinsulated copper wire from EBmeter to fuse unit. (SD-127)

Supplying and fixing 63 A TPNMC switch on suitable angle iron frame work with MS cable entry boxes with earth connection only. (SD 166)

Supply and run of 4 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade on 7 / 20GI bearer wire for service connection mains . (SD - 53)

Supplying and run off 2 of 4 sqwmm (56/0.3) PVC insulated SC unsheatherd cu.conductor of 100 V grade on 7/20 GI bearer wire service connection mains (SD-65)

Supply and run of 2 of 4 sqmm (56/0.30) PVC insulated SC unsheathed cu.conductor of 1100 V grade in 25mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron upright and end supports for main.(SD-70)

Supplying and fixing of 3 nos. of 100A porcelain fuse units 500 Volt of approved brand having ISI mark in T.W Board of suitable size etc., complete in all respects. (Pwd sor p.no : 126)

Supply and fixing of 400A 3 Pole MCCB on suitablewith necessary internal connections for controlling the power plug (Electrical pwd sor 32)

Supply and fixing of Rotary Handle for 400A/ 630A on suitable with necessary internal connections for controlling the power plug (Electrical pwd sor 33)

Supply and fixing of 400A Spreader Terminal on suitable with necessary internal connections for controlling the power plug (Electrical pwd sor 32)

Supply and fixing of400A Change Over Switch on suitable with necessary internal connections for controlling the power plug (Electrical pwd sor 32)

Supply and fixing of 400A TPN Switch Disconnector Fuse Units in Sheet Steel Enclosure with HRC fuses Double Break (Electrical pwd sor 17)

Supply and fixing of 400APanel Board Fuse Units in Sheet Steel Enclosure with HRC fuses Double Break (Electrical pwd sor 55)

Supply and fixing of 5 TR Split AC

Supply and erection of 10 persons carrying capacity of passenger lift of car inner size 1300 X 1350mm for Basement + five Floors (6 Floors) (ie) 20m travel height with a speed of 1.00Mtr per second with ARD , the entrance will be on front side only and 3 No of Entrances on each floor, without machine room and gear less operation and the lift well size is 2150 X 1850mm and with 1 No of Circular fan, LED Light fittings. The landing entrance opening with sliding Door and made up of Stainless Steel SS 304 Grade Hairline finish. The Lift make will be of Johnson / Kone / OTIS / Equivalent.

GI STEEL TUBULAR POLE FOR STREET LIGHT 6 Metre Length Double Bracket Pole with Base Plate(250 x 250 x 6mm) 76.10mm OD x 3.65mm Thick x 6000mm Length PWD SOR P.NO 148

Supply and fixing of 150W LED Street Light Fitting with LED (Philips/Havells) completePWD SOR P.NO 115

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No.(e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., LevelSwitch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact. (250 Litres) pwd sor pg no 72)

Supply fixing and errection of CCTV Camara including cost and Conveyance of all materials to site etc complete as per Specification (5units / park)(PWD SOR Page (153 TO 157) - CCTV Camera (Q)

Network Video Recorder32 Channel - 2 SATA (2 Nos. Hard Disk) (PWD SOR P.NO :154)

Hard disc for NVR 4TB (PWD SOR P.NO :155)

24 Port Patch Panel (PWD SOR P.NO :156)

Rack With Accesssories -4U (PWD SOR P.NO :155)

Armoured LAN & CCTV Cable (CAT-6) (PWD SOR P.NO 153)

29" Led TV for display (Q)

Supply and installation of Anutone (or) Euivalent Brand of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core fully encapsulated ceiling tile of size 595 x 595 x 15mm having volumedensity 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid system. Skelet trelis T15 metal grid system of 600 x 600mm module includes skelet WA15 W30 wall angle with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the skelet MT15 W36 MainT with flange width 15mm, height 32mm and length 3600mm, from the soffit slab with help of soffit cleat and wire rod with leveling spring clip at 1200mm centres. Skelet CT15 W12 CrossT with flange width 15mm, height 26mm and length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm centers in the perpendicular direction to the Main T15. Finally, the skelet CT15W06 CrossT with flange width 15mm, height26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module. The subtex nubby square edge of size 595 x 595x 15mm shall be placed into the grid size of 600 x 600mm. Ensure arrow marks behind the tiles are oriented in one direction to achieve uniform shade. The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an neat appearance as directed by the department offices. The cost includes, cost of material, cost of labour, scaffolding, transportation, conveyance, etc. complying to standard specication. (PWD SOR P.NO :59)

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original conditionwherever found neccessary etc, complete as perstandard specification and as directed by theDepartmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENTPWD SOR Page No. 97 Sl. No.382

First Aid Box complete with all First Aid Medicines PWD SOR Page 142. Sl.No.8c

4 Nos of Fire Buckets made out of 40x40x6mm MS Angle PWD SOR Page 142. Sl.No.8e

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by theDepartmental Officers. PWD SOR Page No. 81. Sl.No.330

Providing and fixing of MS ‘C’ class medium grade IS:1239 / 3589 (part-I) above ground piping with welded joints including all fittings, fixed on the wall with MS brackets at every 2500 mm. The entire piping system shall be pressure tested to a pressure of 15 Kg/ sq.cm and held for hours. The pipe after pressure testing is to be applied with one coat of zinc chromate primer paint and two coats of PO red synthetic enamel paint. The piping system shall be done as per the directions of engineer in charge. - 100 mm Dia Pipe

80 mm Dia Pipe

50 mm Dia Pipe

40 mm Dia Pipe

Supply of fire fighting application MS Hose Box to keep two number of hoses and 1 no of branch pipe with nozzile having proper glass window type double door with universe open key, painted inside white and out side post office red. Near hydrant point, including conveyance, all incidential charges, necessary scaffolding and re-doing the dismantled portion to its original condition wherever found necessary etc., as per standard specificationand as derected by the departmental officers. make omex/kartar/life gaurd/ safe gaurd/ equivalent.-

Supply, installation of fire fighting application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 mtrs long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20 mm dia ball valve and open and close spary nozzle, warm clip, etc., as per the standared pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidential charges, necessary scaffolding and re-doing the dismantled portion to its original condition wherever found necessary etc., as per standard specificationand as derected by the departmental officers. make omex/kartar/life gaurd/ safe gaurd/ equivalent.-

Supply and fixing , in possition of fire fighting application hose of 63 mm dia 15m length binded by copper wire with 63 mm stainless steeel male and female instatanous fire necessary distance by self rolling spindle wheel including necessary 20 mm dia ball valve and open and close spary nozzle, warm clip, etc., as per the standared pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidential charges, necessary scaffolding and re-doing the dismantled portion to its original condition wherever found necessary etc., as per standard specificationand as derected by the departmental officers. make omex/kartar/life gaurd/ safe gaurd/ equivalent.-

Suppy and Fixing of Air release valve of 20mm dia so as to release air lock in 100mm dia MS pipe at top most wet riser as directed by the departmental officers.

Supply, installation, testing and commissioning of Manual call point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per stantared methods and as directed by Departmental officers (Make: ravel / equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per stantared methods and as directed by Departmental officers (Make: ravel / equivalent)

Supply, Instalation, testing and commessioning of micro processor based conventional 12 zone fire alarm control panel heving the rating of 24 volts dc power supply, consisting 230/24 volts smps unit, 2 nos. of 12 volts, 7 ah standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per stantared methods and as directed by Departmental officers

Supply and laying of FRLS PVS insulated 2 core 1.5 sq.mm Armoured copper cable on ceilling / wall using fixing accessories like screws, plug, clamps and etc., as per stantared methods and as directed by Departmental officers

Supply , Installation testing and commissioning of 15 watts wall mounted type SPEAKER etc., as per stantared methods and as directed by Departmental officers

Supply , Installation testing and commissioning of 240 watts Mixer type AMPLIFER 240 watts output, 100 volts etc., as per stantared methods and as directed by Departmental officers

Supply , Installation testing and commissioning of 12 Zone GOOSE VEE MIC etc., as per stantared methods and as directed by Departmental officers

Supply and laying of 2 core 1.5 sqmm armoured copper cable for control wiring to the terrace pump motor with runs of 14 swg tc wire for earthing, providing in wall with suitble size clmps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the deparmental officers -

Supply and fixing nominal bore quartized bulb type Sprinkler bulb 68 deg C fast response pendent type including GI coller for each sprinkler bulb, mounted in MS Pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all including all charges, necessary scaffolding and re-doing the dismantled portion to its original condition wherever found necessary etc., as per standard specificationand as derected by the departmental officers. make omex/kartar/life gaurd/ safe gaurd/ equivalent. - 68*C pedant type

Supply Installation testing and commissioning of conventional smoke detector suitably mounted on ceiling with junction box / false ceiling using fixing accessories like screw,plug,clamps etc as per standard specification and as directed by the departmental officers

Supplying, Installing and commissioning of electrical motor driven jockey pump (hydrant & sprinkler) of horizontal multi stage centifugal end suction backpull out type with gland packing and capable to deliver 1801 lpm (10.8m3/hr) at 140 mwc with all neccessary accessories like bronze impeller, stainless steel shaft along with anti - vibration mounting pad and flexible connections at discharge end of pipes, pump should have dry run sensor provisions etc, and shall be attomatic operation, The pump shall be coupled to motor of 15kw (20hp) with speed of 2900 rpm and complete set shall be mounted on common base frame, including providing & fixing of coupling, coupling gaurd and foundation bolts. etc as per standard specification and as directed by the departmental officers

Supply Installation Testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following complete in all respects as required. A. 1 no Horizontal split casing centrifugal type fire pump capable of delivering 2850LPM against a total head of 110m so as to ensure a minimum pressure of 3.5kg per sq.cm at the farthest top most hydrant / outlet with pump casing of cast iron to grade FG 200,IS 210-1978 and parts like impeller , shaft sleeve,bearing ring,etc of non corrosive metal like bronze , brass or gun metal and shaft of stainless steel.

Installing testing and commissioning of Electrical motor driven Main (Hydrant & Sprinkler) Pump of horizontal centifugal end suction backpull out type with gland packing and capable to deliver 2850LPM (171m3/ Hr) at 140 MWC with all necessary accessories like bronze impeller, stainless stell shaft along with anti - vibration mounting, coupling, coupling guard and base plate for pump, fabricated mild steel channel, foundation bolts and pump should have the dry run sensor provisions, etc, as per local fire brigade requirement,

Supply, fixing, testing & commessioning of dial type (150mm) Glycerin filled pressure gauge with isolation ball valve suitable for working pressure of 250 PSI with no syphon, cost shall be inclusive for providing any short pieces, nipples, elbows etc all complete as per standard specification and directed by the departmental officers

Supplying, installing, testing and commisioning of Suitable pressure switch of reputed make line Indfoss or Donfoss including necessary valves,couplings etc connected with electrical main conteol panel and setup at proper differential so as to autostart and auto stop the electrical motor ,jockey motor including conveyance all incidental charges necessary scaffolding and redoing the dismantled portions to its original condition wherever found necessary etc all ccomplete as per standard specification and directed by the depatmental officers

Supply, eretion of 300mm dia RCC hume pipe for road crossing the pipe line etc complete as per standard specification and as directed by the departmental officers

Supply Installation at approved location approved make Fire Buckets of 24 gauge galvanised steel sheet,standard 9 litre capacity and of round bottom type enamel painted white inside & red outside and letter "FIRE" in black with MS stand etc all complete s per standard specification as directed by the deprtmental officers

R R THULASI BUILDERS INDIA P LTD (BID ID -1536309)