COMPREHENSIVE MAINT INCLUDING JOINERY REPAIR TO CERTAIN OTM ACCN BUILDING IN KLP LOCATION AND MD ACCN BUILDING AT MAP PH-I, II AND KHETRAPAL ENCLAVE INCLUDING LEEKAGE/SEEPAGE REPAIR UNDER AGE B/R-II AT SURATGARH MIL STN

Amount

Demolition of reinforced cement concrete (unreinforcement) as in floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engineer-in-charge.

Dismantling of boarding, any description fixed in any position with nails complete all as specified and directed by Engineer-in-charge.

Dismalting existing wooden flooring (Squash court) of any thickness including runners (70mm x 45mm) & cushion pads complete all as specified and directed by Engineer-in-charge.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engineer-in-Charge.

Taking down steel window / ventilator of any description and of any type with or without guard bars and making good the disturbed portion complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

Taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge.

Taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each complete all as specified and as directed by Engineer-in-charge.

Taking down shutters of any description exc 1 Sqm complete all as specified and as directed by Engineer-in-charge.

M&L for preparation sunken surfaces by cleaning of and removal of loose concrete and filling cracks with polymer modified mortar using Dr. Fixit Pidicrete URP or equivalent in Forsoc, thermax, sikka and other approved make and applying 2 coats of Dr. Fixit Bath seal WPC in suken areas and laying a protective plaster in 10mm thickness in cement mortar (1:3) admixed with Dr. Fixit Pidicrete LW + @ 220ML per bag of cement applying mix of cement water in the ratio 1:1:5 by volume using DR FIXIT PIDICRETE URP chemical on floor and vertical surface of sunken floor as per manufacturers instructions complete all as specified and directed by Engineer-in-charge.

M&L for PCC (1:5:10) type E-2 using 40 mm graded brick aggregate in, filling and mass concrete as in sunken portion complete all as specified and as directed by Engineer-in-charge.

M & L for plain cement concrete (1:3:6) type C-1 using 12.5mm graded stone aggregate as in filling of pressed steel frame, chowkats, hold fast blocks and other similar items etc complete all as specified and directed by Engineer-in-Charge.

M&L for 35mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces complete all as specified and directed by Engineer-in-charge.

S&F 35mm thick factory made glazed and skeleton shutters made of second class hard wood (Bonsum/Hollock), open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Part I Section 8 Clause 8.24 (a) kiln seasoned and chemically pressure treated fixed to chowkat complete all as specified and directed by Engineer-in-charge.

S&F 35 mm thick factory made plain framed, panelled shutter (any number of panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood (Hollock or Bonsum) complete all as specified and directed by Engineer-in-charge.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge

S&F second class hard wood plain solid, straight chowkat and frames wrought framed rebated or the solid rounded or chamfered put together with glue pinned joints complete all as specified and directed by Engineer-in-charge.

S&F 28 to 30mm thick (styles) factory made solid PVC moulded Door shutter, with 2, 4, or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face & 2mm thick prelaminated PVC sheet on back face complete all as specified & shown in relevant drawing of item No. 8101 to 8105 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F 100mm size stainless steel butt hinges cold rolled heavy weight (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F continuous piano hinges mild steel bright finish or electrogalvanised of 30mm flap width complete all as specified and directed by Engineer-in-charge..

S&F 300mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F 150mm long extruded aluminium handles, anodised, fabricated type (ISI marked) complete all as specified and directed by Engineer-in-Charge

S&F as in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 140mm (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F as in repair aluminium (Die cast) body door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80kg (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F as in repair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made out of mild steel heavy duty & fixed (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F as in repair 100 mm aluminium anodised Hasp and staple, safety type with mild steel hinge pin including bolt to hinge plate (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples

S&F as in repair aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples

S&F as in repairs stainless steel drapery rod of 20 mm inner dia (in lengths as directed) with & including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

S&F factory made steel window with side hung shutters including projecting type hinges with steel handle, steel peg stay, fixing lugs etc complete with glazing bars including one shop coat of red oxide primer and Cutting holes in brick wall built in cement mortar for inserting lugs and making good dismantled portion in cement mortor (1:3) or cement concrete (1:2:4) type B-I complete all as specified & directed by Engineer-in- charge

S&F factory made steel window with side hung shutters including projecting type hinges with steel handle, steel peg stay, fixing lugs etc complete without glazing bars including one shop coat of red oxide primer and Cutting holes in brick wall built in cement mortar for inserting lugs and making good dismantled portion in cement mortor (1:3) or cement concrete (1:2:4) type B-I complete all as specified & directed by Engineer-in- charge

S&F pressed steel frames for door of size 125x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc made out of mild steel sheet of 1.25mm thickness complete all as specified and as directed.

S&F anodised aluminium frames powder coated (thickness of powder coating shall not less than 50 micron) for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and directed by Engineer-in-Charge.

S&F anodised aluminium doors shutters powder coated (thickness of powder coating shall not less than 50 micron) sliding / openable having aluminium sections weighting 0.55 Kg/RM including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, 100mm size, 4 levers brass mortice lock vertical type (01 No), hinges, anodised aluminium snap beading, screws complete all as specified and directed by Engineer-in-Charge.

S&F anodized aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws rubber neoprene packing including anodised aluminium fitting such as peg stay 150mm long (1 No), hinges type B21 100mm size (2 Nos), suitable handle (1No) complete all as specified and directed by Engineer-in-Charge.

S&F anodised aluminium window / ventilators shutters powder coated (thickness of powder coating shall not less than 50 micron) side hung type, without sash bars having aluminium sections weighting 0.55 Kg/RM including necessary jointing cleats, glazing clips, anodised aluminium snap beading, screws, rubber neoprene packing including anodised aluminium fitting such as peg stay 150mm long (1 No), hinges type B21 100mm size (2 Nos), suitable handle (1No) complete all as specified and directed by Engineer-in-Charge.

M&L for 18/19 mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and directed by Engineer-in-charge.

M&L for 18/19mm thick extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails complete all as specified & directed by Engineer-in- charge.

M&L for 18-20mm thick Granite (of any type) slab of approved shade as in cooking platforms, steps, jambs, pillars, window cills and the like etc, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) over & including 15mm thick screed bed (bedding layer) in CM (1:6) complete all as specified and directed by Engineer-in-charge. Note : The exposed edges of granite stone slab shall be made full round & polished to mirror finish and rate quoted shall deemed to include this provision.

M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed by Engineer-in-charge.

M&L for glazed ceramic tiles (coloured) 450mm x 350mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge.

Supply and installation of folowing fittings / accessories for squash court :- (i) Top Ssurface board :- Top surface board sall be Kiln seasoned & heat treated imported original first class American maple wood flooring of thickness 21mm, minimum 100mm wide and in random length in tongue and groove shape on all four sides. The edge and border will have a fingerlock groove and the bottom with air pass groove and treated with special anti termite wood resistant liquer. (ii) Under frame :- The under frame shall be made of commercial quality pine wood (Original canadian) runner of 70mm x 45mm treated with anti termite solution and fixed on bottom side with10mm thick EPDM air cushion pads, stapled through the two wings at 300mm x 300mm. (iii) Installation :- IPS sub floor treated with vapour barrier to be placed on the levelled IPS sub floor before laying the under frame. The runners having EPDM air cushion cushion pads to be placed on the vapour barrier in a perfect level at 300mm in one direction. The surface board to be sdrewedand nailed to the pine wood runners through tongue and groove only and will lock the screwed tounge by the groove of adjoining board. Ends of the board will be locked by the inserting the wooden fingers through the edge grooves and fixed with suitable adhesive. An expansion od 08 to 10mm to be left open between the wooden flooring and the surrounding tiled area / walls. (iv) Finishing :- The top surface board (Maple wooden floor) will be sanded in uniform level using a machine sanded in uniform level and finished with 2 coats of bona water based Polyurethene lacquer. (v) Warrantee :- Minimum 05 years Manufacturing warranty must be submitted by the firm

M&L for game line marking in required colours by two coat of water based line marking paint in RAL3020 or BS04E53 for squash court wooden flooring complete all as specified and directed by Engineer-in-charge.

M&L for 10mm thick rendering in cement mortar (1:4) on fair faced or on other than fair face surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for 10mm thick rendering in cement mortar (1:3) on brick or concrete surface of ceiling, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered and unplastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of appropirate primer over and including 1mm thick layer of wall putty (Make J K or Birla) complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

M&L for preparation of steel surface already treated with primer over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, treating end of posts back of chowkhats, area tarred exc 0.1 sqm not exc 0.5 sqm each new or old of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and as directed by Engineer-in-Charge

Hacking out old broken glass any thickness, size, quality or description from wooden / metal frame and punching or drilling out old glazing pins/spring clips complete all as specified and directed by Engineer-in-charge.

M&L for securing of old glass of any description in existing metal frame glazed with putty / beads including removing loose or decayed putty, beads painting / oiling one coat on rebates, groves reputting and painting / oiling puttied surface to match existing work (New length of frame reputtied shall be measured complete all as specified and directed by Engineer-in-charge.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed.

S&F 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by Engineer-in-charge.

S&F 5mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by Engineer-in-charge.

S&F 5.5mm thick tinted glass black colour not exc 0.50 Sqm in each pane complete all as specified and directed by Engineer-in-Charge .

S&F 6.3mm thick tinted glass black colour exc 0.50 Sqm in each pane complete all as specified and directed by Engineer-in-Charge .

S&F solar control film 25 micron reflective type exc 1.5 sqm sticked to glass panes as per manufacturer's instructions complete all as specified & directed by Engineer-in-charge.

S&F as in repair 15mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-charge.

S&F as in repair 20 mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-charge.

S&F as in repair 32 mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-charge.

S&F as in repair 15mm bore brass chromium plated shower rose with or without swivel joints, any size, including fixing to steel pipe or union with shower arm 15mm size, 195mm long iwht bend of 45 degree with flange complete all as specified and directed by Engineer-in-charge. Make shower rose :- Jaquar Cat part No OHS-CHR-1661, Kohler Cat Part No K-23152IN-CP or equivalent in makes mentioned in Appendix 'A' here-in-after. Make shower arm :- Jaquar Cat part No SHA-CHR-477, Kohler Cat Part No 26318IN-CP or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repair 450mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge.

S&F as in repair chromium plated towel ring round with round flange 200mm dia including chromium plated brass screws and plastic cleats complete all as specified & directed by Engineer-in-Charge. Make :- Jaquar ESSCO AEC-1121NB / Cera cat part No F5003105 / Somany cat part No 272130740071 or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repair brass chromium plated tubular towel rail 20mm dia; 'D' type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge. Make :- Jaquar ESSCO AEC-1111NB / Cera cat part No F5007103 / Somany cat part No 272130740051 or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. Make : Jaquar cat part No ALD-CHR-573 / Kohler cat part No K-98100IN-CP / Jhonson cat part No S0426C or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repair 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge. Make :- Jaquar Cat part No CON-CHR-107KN, Kohler Cat Part No K-16093IN-4-CP, Marc Cat part No MSP-2080, Grohe Cat Part No 20238000 or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repairs 15mm bore brass L bend chromium plated basin mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore complete all as specified and directed by Engineer-in-charge. Make : Parryware cat part No T1916A1 / Jaquar Cat part No ESSCO MQT-517BKN / Cera cat part No F2002401 / Somany cat part No 272201250011 / Marc ES-517-B or equivalent in Makes mentioned in Appendix 'A' here-in-after.

S&F as in repair 15mm bore angle valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge. Make :- Jaquar Cat part No FUS-CHR-29053, Kohler Cat Part No 76390IN-9-CP or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repair vitreous china wash basin white, flat back of size 550x400mm including including a pair of cast iron brackets embedded in PCC 1:3:6 type C-1 blocks of size 10 x 7.5 x15 cm with & including 32 mm dia PVC waste pipe, 32mm dia PTMT waste coupling half or full thread (minimum wt 45 grms) flange end bedded in red lead cement & other end fixed to waste pipe and including brass chromium plated fancy type pillar tap, screwed suitable for iron pipes of 15mm bore complete all as specified and directed by Engineer-in-Charge.

S&F as in repair vitreous china squatting pan Orissa pattern, white of size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, PCC filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-charge. Make :- Parryware Cat part No C0117, Cera Cat Part No S3020105 or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repairs vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device and jet spray complete all as specified & as directed by Engineer-in-charge. Make :- Cera Cat part No S1053105 & B1520103 and Parryware cat part No C0220 & E8309 or equivalent in Makes mentioned in Appendix 'A' here-in-after.

S&F as in repair 10 litre capacity PVC valveless symphonic action type low level flushing cistern (ISI marked) including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer-in-charge. Make :- Parryware Cat part No E8109 SLIMLINE ECONOMY, Hindware Cat Part No 509801, Cera Cat part No B1010112 or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repairs PVC waste pipe 32 to 40mm bore suitable for WHB or Sink complete all as specified and directed by Engineer-in-charge.

S&F 100 mm bore cast iron sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls including requisite number of clamps made out of 25x4mm flat iron complete all as specified and directed by Engineer-in-charge.

S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in-charge.

S & F as in repair brass chromium plated bottle trap with 32mm dia discharge pipe having minimum water seal or 25mm for wash basin with inlet and outlet screwed for pipe or connections including necessary packing , union and cap complete all as specified & directed by Engineer-in-charge. Make :- Cera cat part No F8060101 / Somani cat part No 2721500540411 or equivalent in makes mentioned in Appendix 'A' here-in-after.

S&F as in repair 75mm dia PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed by Engineer-in-Charge.

S&F as in repair 110mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite Number of clamps made out of flat iron 25x4mm complete all as specified and as directed by Engineer-in-charge.

S&F 75mm bore PVC (SWR) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite Number of clamps made out of flat iron 25x4mm complete all as specified and as directed by Engineer-in-charge.

S&F 110 mm bore PVC (SWR) bends any radius jointed with adhesive complete all as specified and as directed by Engineer-in-charge.

S&F 110 mm bore PVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 75 mm bore PVC (SWR) bends any radius jointed with adhesive complete all as specified and as directed by Engineer-in-charge.

S&F 75 mm bore PVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 110mm bore PVC (SWR) junction,single (single T) equal or unequal complete all as specified and directed by Engineer-in-Charge"

S&F 75mm bore PVC (SWR) junction,single (single T) equal or unequal complete all as specified and directed by Engineer-in-Charge. ---------------------------------------------------------------------------- Note :- A sum of Rs. 130581/- will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 22 & 23 (Schedule of Credit) of Tender documents.

GARG ENTERPRISES

S.K BUILDERS AND ENGINEERS

M/s JUGAL KISHORE MISHRA AND SONS

Aman Enterprises

Gupta Suppliers

M/S MANIRAM BISHNOI