Forest Department Division Rohru, Distt.Shimla, H.P. SH Construction of Type II Quarters for Ministerial Staff Under Schedule Caste Development Programe under demand No.32 for the year 2024-25

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil in all lead and lift as directed and entire satisfaction of the Engineer -in -charge in All kinds of soil i/c ordinary rock.i/c civil work and carriage of material in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size).i/c civil work and carriage of material in all leads and lifts.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering 1:5:10 (1 cement : 5 coarse sand): 10graded stone aggregate 40 mm nominal size).i/c civil work and carriage of material in all leads and lifts.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.i/c civil work and carriage of material in all leads and lifts.

Providing and laying of synthetic Polyester triangular fibre of length 12mm, effective diameter 10-40 microns and specific gravity of 1.34 to 1.40 in cement concrete (Outer surface plaster) by using 125gms of synthetic Polyester triangular fibre for 50 Kg cement used as per directions of Engineer-in-Charge.i/c civil work and carriage of material in all leads and lifts.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concret.i/c civil work and carriage of material in all leads and lifts.

Suspended floors, roofs, landings, balconies and access platform.i/c civil work and carriage of material in all leads and lifts.

Shelves (Cast in situ).i/c civil work and carriage of material in all leads and lifts.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.i/c civil work and carriage of material in all leads and lifts.

Columns, Pillars, Piers, Abutments, Posts and Struts.i/c civil work and carriage of material in all leads and lifts.

Edges of slabs and breaks in floors and walls up to any width.i/c civil work and carriage of material in all leads and lifts.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding with PVC cross lock all complete including cost of binding wire upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.i/c civil work and carriage of material in all leads and lifts.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding PVC cross lock all complete including cost of binding wire above plinth levelThermo-Mechanically Treated bars of grade Fe-500D or more.i/c civil work and carriage of material in all leads and lifts.

Providing and laying in design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.All works upto plinth level.i/c civil work and carriage of material in all leads and lifts.

All works above plinth level upto floor all level.i/c civil work and carriage of material in all leads and lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand).i/c civil work and carriage of material in all leads and lifts.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level Cement mortar 1:4 (1 cement :4 coarse sand).i/c civil work and carriage of material in all leads and lifts.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, mouldingand polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade.i/c civil work and carriage of material in all leads and lifts.

Providing wood work in frames of doors, windows, clerestorywindowsandother frames, wrought framed and fixed inpositionwithhold fast lugsor withdash fastenersof requireddia& length ( hold fast lugsor dash fastener shall be paid for separately). Sal wood.i/c civil work and carriage of material in all leads and lifts.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixingwithbutt hingesof requiredsizewithnecessary screws, excluding panelling which will be paid for separately,all completeasperdirectionofEngineer-in charge. (Note:- Butt hinges and necessary screws shall be paid separately)Kiln seasoned and chemically treated hollock wood 35mm thick.i/c civil work and carriage of material in all leads and lifts.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.i/c civil work and carriage of material in all leads and lifts.

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws Kiln seasoned and chemically treated hollock wood.35 mm thick .i/c civil work and carriage of material in all leads and lifts.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood 50x12mm.i/c civil work and carriage of material in all leads and lifts.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complet 25 mm dia.i/c civil work and carriage of material in all leads and lifts.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.i/c civil work and carriage of material in all leads and lifts.

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 75mm.i/c civil work and carriage of material in all leads and lifts.

Providing and Fixing brass handles to required colour and shade with necessary screws, etc. complete including carriage of material in all leads and lifts 125mm.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.i/c civil work and carriage of material in all leads and lifts.

Providing and Fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16mm. i/c civil work and carriage of material in all leads and lifts.

Providing and Fixing bright/ matt finished stainless steel tower bolts of approved quality & make with necessary screws etc complete : 300x10mm

Providing and Fixing bright/ matt finished stainless steel tower bolts of approved quality & make with necessary screws etc complete : 200x10mm

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (for bathroom, W.C. doors and Cup Board) using synthetic rubber based adhesive.

Providing and fixing 19mm thick commercial board water proof in shelves for cup boards with butt joints and fixing with nails and screws etc. including 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles of any size of approved shade and colour in flooring, treads of steps and landings laid over 20mm thick cement mortar 1:4 (1 cement : 4 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete.

Providing and fixing 8mm thick digital glazed tiles conforming to IS : 15622 of approved make in all colours, shades any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying 10mm thick vitrified floor tiles of any size with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete

Providing and laying 8 mm thick Vitrified tiles of any size with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid laid on 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand), jointing with grey cement slurry complete in all respect.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°

Shoe (Plain) 110 mm Shoe

15 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)for interior / exterior wall surfaces up to all floor level including arrises, internal rounded angels,chamfers and or rounded angels not exceeding 80mm in girth and finished even and smooth complete in all resect.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) to ceilling sloping surfaces

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Finishing walls with weather proof exterior grade emulsion of approved design (Apexultima) for its equarlied on undercoated walls surfaces (Two Coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other forien matter etc. including sand paper smooth complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Stone soling properly hand packed filling interstices with spalls and consolidating with hand ramming including spreading watering and rolling of binding materials moorum or earth etc. complete as per H.P.P.W.D. specifications. 100mm spread thickness (fin

Providing and Fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete

Providing and Fixing wash basin of standard pattern, including , cutting and making good the walls wherever required.

Providing and Fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and Fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with stainless steel plug 40 mm, including , cutting and making good the walls wherever required : Single/ Double Bowl

Providing and Fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia.

Providing and Fixing 100 mm steel grating or nahani trap.

Providing and Fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Oval shape 450x350 mm (outer dimensions).

Providing and Fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and Fixing toilet paper holder : C.P. brass.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 75 mm

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete.110 mm dia.

75 mm dia.

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete.110 mm dia.

75 mm dia.

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete.110 mm dia.

75 mm dia.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete110 mm dia.

75 mm dia.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete.110 mm dia.

75 mm dia.

Providing and fixing air admitave valve (cowel) ISI marked including fixing with approved adhesive etc. complete110 mm dia.

75 mm dia.

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugallycast (spun) ironpipesof diameter : 100 mm

Providing and Fixing liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour.

Providing and Fixing towel ring round shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and Fixing 450 mm long C.P. towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

Providing and Fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and Fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws:

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge.1216 (16 mm OD) pipe

Providing and Fixing uplasticised PVC connection pipe with brass unions :45 cm length.

Providing and Fixing C.P. brass shower rose with 15 or 20 mm inlet.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipesincludingnecessary fittings fittings and the base support for tank.

Providing and Fixing C.P. brass bib cock of approved quality 15mm dia.

Providing and Fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore.

Providing and Fixing Mixer for kitchen sink with casted swinging spout at top.

Providing and Fixing C.P. brass stop cock (concealed). 15 mm nominal bore.

Providing and Fixing C.P. brass angle valve for basin mixer and geyser points . 15mm nominal bore.

Providing and Fixing C.P. Brass extension nipple (size 15mmx50mm).

Providing and fixing PTMT Ball cock of approved quality,colourandmakecompletewithEpoxycoatedaluminium rod with L.P./ H.P.H.D. plastic ball.15 mm nominal bore, 105 mm long, weighing not less than 138 gms.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting f:layiInsgt cinotuergsrealocfeampepnlytinbgasceedmterenat tsmluernryt f@or 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off unction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and Laying cement concrete 1:5:10 (1Cement:5coarse sand:: 10 graded stone agrregate 20mm mm nominal size) and curing complete including the cost of form work for plain/reinforced concrete in retaining walls, breast walls, i/c weephole as per technical specifications.

Stone filling behind retaining walls :

Providing & laying U-shape P.C.C. drain of size 45x25cm with cement mortar 1:3:6 (1 Cement : 3 coarse sand) : 6 graded stone aggregate 20 mm nominal size) and curing complete including form work etc thickness of concrete will be as 10cm complete as per the direction of the Engineer-in-charge.

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 25 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Providing push-on-joints to Centrifugally (Spun) Cast IronPipesor Ductile Iron Pipes including testing of joints and the cost of rubber gasket :150 mm dia pipe

Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :150 mm dia Ductile Iron Class K-9 pipes

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including SFRC Cover 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :For pipes 100 to 250 mm diameter

Please Enable Macros to View BoQ information