REPAIR TO LEAKAGE / SEEPAGE IN TOILETS, CHAJJA, ROOF PROJECTION AND TILING, TRAVERSE WALL AND MISC ITEMS AND REPAIR /MAINT OF JOINERY AND OTHER B/R SERVICES IN TECH AREA AT AF STN JAISALMER

Amount

Applying evenly a tack coat of industrial bitumen grade 85/25 at the rate 1.20 Kg/sqm over one coat of cold bitumenous oil based primer (IS : 3384) at the rate 250 gm/sqm including cleaning surfaces including 10mm thick cement plaster in cement and sand mortar (1:4) on concrete surfaces, finished even and smooth without using extra cement with water proofing compound including dismentling /taking down existing complete all as specified and directed. Note : Water proofing compound will be measured and paid for seperately.

Cutting grooves in brick or stone masonry wall for inserting APP membrane 75mm wide and 65mm deep and making good shaping horizontal face of groove with cement and sand mortar 1:3 or PCC 1:2:4 complete all as specified & as directed.

Supply only integral liquid water proofing compound, ISI marked, complete all as specified and as directed .

APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (weight not less than 150 gms/sqm) land on primed surface by LPG torched application including dismentling /taking down existing complete all as specified and directed.

Fixing only of exisitng old APP based polymeric membrane by forced torch application complete all as specified.

75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints , laid in trenches/floor including taking down old unserviceable pipecomplete all as specified and directed.

75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down old unserviceable pipe complete all as specified and directed.

110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints , laid in trenches/floor including taking down old unserviceable pipe complete all as specified and directed.

110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down old unserviceable pipe complete all as specified and directed.

75 mm bore PVC (SWR) bend any radius provided fixed complete all as specified and directed.

75mm bore PVC (SWR) bend any radius provided with access door fixed complete all as specified and directed.

110mm bore PVC (SWR) bend any radius provided fixed complete all as specified and directed.

110mm bore PVC (SWR) Junction Single (Single T) equal or unequal provided with access door fixed complete all as specified and directed.

110mm bore PVC (SWR) vent cowl fixed complete all as specified and directed.

PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cement and jointing to waste pipe fixed in cement concrete type B-1:2:4 complete all as specified and directed.

Precast Cement Concrete 1:2:4 type B1 using 20mm graded stone aggregate as in landing cover slab (for manholes) and similar articles with plain faces including use and waste of formwork as required and set in cement and sand mortar (1:6) and including demolition of existing reinforced cement concrete complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Mild steel TMT bars 6mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Ditto- all as per Srl item No 18.00 here-in-before but 6 mm dia and over upto and including 8 mm dia as in stirrups, spacers and binders complete all as specified and as directed

Vitreous china wash hand basin white colour flat back of size 550x400mm including cutting for and pinning in ends of or erecting stand including waste fitting, brass chromium plated 32mm size with longh with including a pair of cast iron brackets embedded in PCC 1:3:6 type C-1 blocks of size 10x7.5x15cm with including dismantling and taking down old unserviceable complete all as specified and directed.

Precast cement concrete (1:3:6), type C-1 (using 20mm graded stone aggregate) as solid block masonary exceeding 10cm and set in cement and sand mortar (1:6) including demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed.

20mm thick black granite slab/ tiles in floors/treads etc, set & jointed with neat cement slurry over and including 15mm thick screed bed in cement mortar (1:6) and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) complete all as specified and as directed.

Vitreous china EWC, with `P' trap, colour white, with 10ltr low level cisten (LLC) including internal fitting (including fixing bolts, flushing cistern and flush pipe) including plastic water closet seat cover, closed pattern with flat bottom, and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Stainless steel Jet Spary with braided tube 1.50 mtr long fixed as in repair complete all as specified and directed.

Hand Shower (Health Faucet) with 8mm dia 1.50mtr length stainless steel tube and hook with all fittings, fixed as in repair complete all as specified and directed.

Vitreous china bowl urinal, flat back, size 465x355x265mm white colour, including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs and including 60mm long brass screws, pointing around urinal back in cement, with and including grating and union for discharge pipe, including 40mm size brass chromium plated waste coupling with long screwed shanks and flynuts, flange end bedded in red lead cement and other end fixed as in repair complete all as specified.

Urinal spreader of CP any colour for fixing with 15mm dia pipe fixed as in repair complete all as specified and directed.

32mm bore of pipe Low Density Polythylene Pipes (LDPE) with fittings as required of pressure rating 6 kgf/cm2 and fixed complete to walls, ceilings or in floors etc. fixed as in repairs complete all as specified and directed.

40mm bore of pipe Low Density Polythylene Pipes (LDPE) with fittings as required of pressure rating 6 kgf/cm2 and fixed complete to walls, ceilings or in floors etc. fixed as in repairs complete all as specified and directed.

88mm over head shower premium quality sqaure with 225mm stainless steel arm & glange complete all as specified and directed.

Green marble 20mm thick both sides polished machine cut as in urinal partitions of sizes as approved including cutting cheses in walls and setting in neat cement paste complete all as specified & as directed.

Galvanized steel water tubing medium grade of 15mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable existing water tubing and connections , complete all as specified and directed.

Galvanized steel water tubing medium grade of 20mm bore with & including all fittings fixed to walls and ceiling or laid in floors,including taking up or down old unserviceable existing water tubing and connections, complete all as specified and directed.

Stop valve with 15mm bore (concealed type) cast copper alloy chromium plated screwed down, high pressure, screwed both ends for iron pipe or for union fixed as in repair complete all as specified and directed.

15mm bore chromium plated Bib taps fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repairs complete all as specified and directed.

Bathroom mirror (900x600mmx6mm) with frame fixed as in repair complete all as specified and directed.

Preparation of new plastered surfaces and applying white wall care putty on wall to a smmoth finish complete all as specified and directed.

Preparation of new plastered surfaces and applying white wall care putty on ceiling to a smmoth finish complete all as specified

Preparation of new treated/ decorated external wall/roof surfaces of any storeys/height upto 10m of any description and applying two coat of exterior emulsion paint (weather coat) over one coat of primer 1st quality in different tints/shades in sigma/ camouflaging pattern as approved complete all as specified and directed.

Preparation of old decorated wall surfaces of any description and applying one coat of oil emulsion distemper of any tint etc complete all as specified and directed.

Preparation of old treated/ decorated external wall/roof surfaces of any storeys/height more than 10m of any description and applying one coat of exterior emulsion paint (weather coat) 1st quality in different tints/shades in sigma/ camouflaging pattern as approved complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 500 Litre capacity triple layered (white cylindrical vertical with closed top) ISI marked, hoisted & fixed in position with 20mm bore ball valve of high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water storage tank complete all as specified and directed.

20mm dia ball valves, high pressure of PTMT (Polytetra methylene terephthalate) with epoxy coated aluminum rod & high density plastic ball and fly nut, screwed for iron pipe (minimum weight 210 gms) fixed as in repair complete all as specified and as directed.

PVC connection suitable for 15mm bore with PTMT nuts of 450mm length and fixed as in repair complete all as specified and directed.

Tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges fixed as in repair complete all as specified and directed.

RCC (NOMINAL MIX) Type B1 1:2:4 using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, treads , balconies, canopies, deck slabs and in shelves and the like etc including demolition of existing concrete complete all as specified and directed.

RCC (NOMINAL MIX) Type B1 1:2:4 using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span including demolition of existing concrete complete all as specified and directed.

RCC (NOMINAL MIX) Type B1 1:2:4 using 20mm graded stone aggregate as in chajjas, fins, fascias, louvers, parapets and railing etc and the like including demolition of existing concrete complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick flat surfaces (Horizontal or sloping) complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

Use and waste of form work to faces of chajja through and similar item rough finished surface of concrete complete all as specified and as directed

Extra over stone walling for hammer dressing with maximum dipression on face from sraight edge held against the dresses surface n exc 20mm and dressing of face beds and joints as specified to square rubble walling, jodhpur type, brought upto courses complete all as specified and directed.

Keyed pointing in cement and mortar (1:4) to square rubble masonry coursed or brought upto courses etc complete all as specified and directed.

Labour only for Stone/boulders rubble walling (Jodhpur type) brought upto courses, well bonded, bedded and solidly hearted, built in CM (1:6) including dismantling of existing masonry complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers not exceeding 30cm thick, watering, ramming/rolling and finishing to required size, shape, etc., not exceeding 1.5m high from base including supply of approved earth obtained from Air Force campus or from with Air Force station if approved including excavation and carrying to work site and including surface dressing not exceeding 15cm deep and cleaning away all grass, vegetation, saplings, shrubs, bush wood under growth roots, soft/loose soil etc and removing the same etc complete all as specified and as directed. Note : Quantity shall be calculated based on initial and final level reduce level and 10% deduction in quantity shall be applied for payment purpose.

Forming embankments including raising (or lowering) earth, spreading in layers not exceeding 30cm thick, watering, ramming/rolling and finishing to required size, shape, etc., not exceeding 1.5m but not exceeding 3.00m high from base including supply of approved earth obtained from Air Force campus or from with Air Force station if approved including excavation and carrying to work site and including surface dressing not exceeding 15cm deep and cleaning away all grass, vegetation, saplings, shrubs, bush wood under growth roots, soft/loose soil etc and removing the same etc complete all as specified and as directed. Note : Quantity shall be calculated based on initial and final level reduce level and 10% deduction in quantity shall be applied for payment purpose.

Forming embankments including raising (or lowering) earth, spreading in layers not exceeding 30cm thick, watering, ramming/rolling and finishing to required size, shape, etc., not exceeding 3.00m but not exceeding 4.50m high from base including supply of approved earth obtained from Air Force campus or from with Air Force station if approved including excavation and carrying to work site and including surface dressing not exceeding 15cm deep and cleaning away all grass, vegetation, saplings, shrubs, bush wood under growth roots, soft/loose soil etc and removing the same etc complete all as specified and as directed. Note : Quantity shall be calculated based on initial and final level reduce level and 10% deduction in quantity shall be applied for payment purpose.

Forming embankments including raising (or lowering) earth, spreading in layers not exceeding 30cm thick, watering, ramming/rolling and finishing to required size, shape, etc., not exceeding 4.50m but not exceeding 6.00m high from base including supply of approved earth obtained from Air Force campus or from with Air Force station if approved including excavation and carrying to work site and including surface dressing not exceeding 15cm deep and cleaning away all grass, vegetation, saplings, shrubs, bush wood under growth roots, soft/loose soil etc and removing the same etc complete all as specified and as directed. Note : Quantity shall be calculated based on initial and final level reduce level and 10% deduction in quantity shall be applied for payment purpose.

Removing surplus soil to a distance exc 250m but n.exc 500m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed

Taking down chowkhats or frame with shutters (without taking off shutters from the frames), area not exceeding 1.5 Sqm each complete all as specified.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames), area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and directed.

Taking down shutters any description area exceeding 1.00 sqm each but not exceeding 2.00 sqm each complete all as specified and directed.

Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete of Gde E-165 (Fe-290), drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hook and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing in position including taking down complete all as specified and directed. Note : Cost of welding butt hinges to the door frame deemed to included in quoted rate and butt hinges shall be measured & paid for “Supply only” separately under relevant item of this schedule.

Factory made 30mm thick flush shutter, solid core construction, with block boards core and plywood face panels, commercial type on both sides (ISI Marked) fixed to chowkhats complete all as specified and directed.

Wood grain printed 1mm PVC sheet fixed or laid on to flush doors by using rubber based adhesive, supplying & fixing at site as per specification complete all as specified and directed.

Factory made Second class hard wood 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares with plain chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or founded, fitted with cut and mitred beads for securing glass or wire cloth any number, etc sizes of members of shutter as specified in SSR Part-I complete all as specified and directed.

Stainless steel wire cloth 0.56mm nominal dia of wire and average width or aperrture 1.18mm and fixed with tinned tackles or stainless steel wire staples fixed complete all as specified and directed.

Stainless steel wire cloth 0.56mm nominal dia of wire and average width or aperrture 1.18mm and fixed with tinned tackles or stainless steel wire staples and fixed as in repair complete all as specified and directed.

Anodised aluminium extruded sections as in frames for chowkats, doors, windows and ventilator with style and rails or for fixed glazed partitions wall frame made to shape required fixed with 150mm long screw and rawl plug with one or more rebates including necessary joining cleats, glazing clips, rubber neoprene packing for fixing, anodised aluminium snap beading screws etc complete all as specified and directed.

Anodised aluminium sections for door shutters (aluminium sections weighing 0.55 Kg/m) including necessary joining cleats, glazing clips, rubber neoprene packing, extruded anodised aluminium handle 02 Nos in each door shutter, 04 Nos hinges each shutter, anodised aluminium snap beading, screws etc complete all as specified and directed.

Anodized aluminium sections as in window and ventilator shutters, side hung type without sash bars (aluminium sections weighing 0.55 kg/m) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (01 Nos each shutter), extruded anodised aluminium alloy with galvanised mild steel hinge pin, 100mm long (03 Nos each shutter), extruded anodised handle of size 150mm (01 No. each shutter) etc. complete all as specified and as directed.

PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube 19mmx19mmx19 gauge and PDM rubber gasket weather seal to be provided through out the frame. The profile shall be mitre cut at two corners and jointed by inserting 02 Nos of 150mm long brackets of 15mmx15mmx15 gauge MS square tube inside the 19mmx15mm MS square tube and suitable screwed complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (style), consisting of frame made out of MS tubes for stiles and for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified.

Mild steel flat as in hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

100mm Butt hinges, medium weight, cold rolled mild steel (ISI marked) complete all as specified and directed.

250mm long aluminium type sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia with and including minimum 06 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

Aluminium extruded section body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851-1000mm in width & weight between 61 to 80 Kg, complete all as specified and directed.

150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

100mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

Aluminium handle 125mm long cast type, anodized complete all as specified and directed

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed.

4mm thick figured glass, pin head type and glazing with oil putty/wooden beading not exceeding 0.50m sqm in each pane fixed any bldg height including hacking out old broken glasses complete all as specified and directed.

3mm thick sheet glass ordinary quality and glazing with oil putty/aluminium beading not exceeding 0.50 sqm in each pane fixed including hacking out old broken glassescomplete all as specified and directed.

Preparation of newly surfaces of wood or wood based material of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

Prepariation of newly steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Welding in repairs not exceeding 2.5cm in length, thickness of metal to be welded not exceeding 6mm complete all as specified and directed.

Easing and adjusting of steel window/ventilators including removing rusted and forging materials and replacing broken hinges including welding and all labour complete all as specified and directed.

Easing and adjusting of aluminium window including necessary joining cleats, glazing clips, rubber packing and anodised aluminium snap beading, screws, anodised aluminium fittings fixing aluminium bedding, rubber beding removing rusted and forging materials and replacing broken hinges including fixing necessary aluminium flat and aluminium angle complete all as specified and directed.

Easing and adjusting of aluminium door including necessary joining cleats, glazing clips, rubber packing and anodised aluminium snap beading, screws, anodised aluminium fittings fixing aluminium bedding, rubber beding removing rusted and forging materials and replacing broken hinges including fixing necessary aluminium flat and aluminium angle complete all as specified and directed.

Easing and door shutters for easy closing / opening tightening of hinges or changing the position of hinges adjustment of tower bolts, sliding bolts with new screws complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm and fixed as in repair complete all as specified and directed.

Aluminium extruded section body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851-1000mm in width & weight between 61 to 80 Kg, fixed as in repair complete all as specified and directed.

150mm long aluminium anodised barrel tower bolts of extruded section and fixed as in repair complete all as specified and directed.

250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed as in repair complete all as specified and directed.

Aluminium handle 125mm long cast type, anodized fixed as in repair complete all as specified and directed

Plain aluminium sheet 0.56mm thick fixed with screw and fixed as in repair complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum dipression on face from sraight edge held against the dresses surface n exc 20mm and dressing of face beds and joints as specified to square rubble walling, jodhpur type, brought upto courses complete all as specified and directed.

Precast cement concrete (1:3:6), type C-1 (using 20mm graded stone aggregate) as solid block masonary exceeding 10cm and set in cement and sand mortar (1:6) including demolition of existing masonry built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed.

20mm thick black granite slab/ tiles as in floors/treads etc, set & jointed with neat cement slurry over and including 15mm thick screed bed in cement mortar (1:6) and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) including taking down existing complete all as specified and as directed.

20mm thick black granite (of any type) work as in skirting/risers over and including 10mm thick screed bed (backing coat) in cement and sand mortar 1:4, jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of granite stone including cutting and polishing (mirror polish i.e. full granite polish as per local trade practice) including taking down existing complete all as specified & directed.

10mm thick internal plaster in cement mortar (1:6) on internal wall surfaces finished even & smooth, fair without using extra cement including taking down old plaster complete all as specified and directed.

15mm thick external plaster in cement mortar (1:4) on external wall surface finished even & fair without using extra cement including taking down old plaster complete all as specified and directed.

5mm thick plaster in cement mortar (1:3) on surfaces of ceiling, finished even and smooth without using extra cement including taking down old plaster complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer of surfaces of wall and approved complete all as specified and directed.

Preparation of newly plastered surfaces or unplastered surfase of walls and applying two coats of oil emulsion distemper over a coat of chalk whitening complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Glazed coloured ceramic tiles in dado/skirting 300x450x6-7mm / 350mm x250mm x6-7mm thick on vertical surfaces, dado and skirting over and including 15mm thick cement and sand mortar (1:4) backing coat set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tile and including dismantling of existing tiling with cement mortar bedding complete all as specified and directed

Non Skid colouredceramic tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in floors etc over 15mm thick in cement and mortar (1:6) bedding set and jointed in neat cement slurry and pointed in coloured cement to match including dismantling of existing tiling with cement mortar bedding complete all as specified and directed

Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc over 15mm thick in cement and mortar (1:6) bedding set and jointed in neat cement slurry and pointed in coloured cement to matchncluding dismantling of existing tiling with cement mortar bedding complete all as specified and directed.

Non Skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in floors etc over 15mm thick in cement and mortar (1:6) bedding set and jointed in neat cement slurry and pointed in coloured cement to match including dismantling of existing tiling with cement mortar bedding complete all as specified and directed.

Plain cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) in bressumers ,sting courses ,lintel, cill, bed block coping ,bed plate, bond stone with plain and fair faces etc including weathering slightly rounded or chamfered angles and throating including demolition of existing concrete complete all as specified and as directed

Precast reinforced cement concrete jalli 35 mm thick in PCC 1:2:4 type B-0,using 12.5 mm graded aggregate and setting in cement and sand mortar 1:4 etc including demolition of existing concrete complete all as specified and as directed

100 mm thick Plain Cement Concrete,1:3:6 (using 40mm graded stone aggregate) type C- 2 as in floor finished and paving including demolition of existing concrete complete all as specified and as directed

Factory made chequered cement concrete tiles, 25cm x 25cm x 22 mm to 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment, over and including 20 mm thick screed bed in cement and sand mortar 1:6 and including dismantling of existing tiling with cement mortar bedding complete all as specified and directed.

Plain cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in leveling course , benching etc finished even & rough to receive cement mortar screed bed complete all as specified and directed.

S K TRADER