Providing fitting of 1 cusec horizontal centrifugal pump set along with allied electro-mechanical machinery (FASD) including laying of suction and delivery pipes and 150mm MS Rising main with providing and laying of 300mm dia. MS pipe at KOt-II

Amount

Providing/ Installation, Testing and Commissioning of 1 cusec discharge, 25mtr. Head Horizontal Centrifugal Pump coupled with appropriate Motor(1500rpm) with allied accessories at LIS Kot-II. The job involves Providing/ Carriage/ Shifting of the pumping unit i.e. 1 cusec discharge, 25m head HC pump, with motor, base plates and coupling pulley of reputed make to the site of LIS (approx.40Km from Jammu) by engaging manual labour for loading into the Mechanical Transport and unloading the same at roadside at site of LIS. Further carriage of the same from unloading site to site of installation by manual head load by using suitable tools & tackles. Construction of R.C.C. foundation blocks (2m x 1m x 1.5m) for installation of the pumping unit with allied works at LIS Kot-II, Akhnoor. The job involves excavation of the floor of pump room to remove soil to finish with required dimensions at bottom with 1.2m deep, removal of excavated material and disposing off the same as per site conditions, providing & laying of crushed stone 40 mm and ramming, laying of one layer of 1:3:6 concrete mass, upto 0.15mtr. Depth. Providing/fabrication of frame out of angle iron of 40 x40 x6 mm of size (1.75 x0.8x1.25)m with extra length of angle iron supports longitudinally for extra strength. Providing & laying of TMT steel bar 10 mm, 6 inch sq. mesh center to center spacing for the block inside the angle iron frame. Providing & laying of 1:2:4 cement concrete mass 2m x1mx1.35m after providing of requisite size of form work. Fitting of requisite no. of foundation bolts in position as per base frame in the foundation block. Installation of the pumping unit on the base plate. Coupling the HC Pumps with Motors by new coupling pulley, checking alignment of the pumps & motors. The job includes the cost of pumping units along with allied accessories material & carriage charges for all the material from various sources by mechanical transport/head load, cost of hire charges of shuttering material, vibrator and concrete mixture & welding set, POL for vibrator and concrete mixture. Cost of steel, cement, labour for cutting, laying & binding of steel, charges for curing of foundation block and labour charges for skilled and semi skilled labour for the complete job at LIS Kot-II. (Complete Job)

Providing and laying of suction pipe 200 mm dia. (12m approx.) by way of fabrication of 1 nos. M.S pipe bends of suitable angle as per the site conditions from the available 200 mm dia. M.S pipe. Job including providing/fitting of M.S flanges 200 mm dia. as per site requirement of standard thickness which are to be circumferentially welded at two ends of bends and pipes with the ISI marked welded electrodes. Flanges to have suitable drilled holes to match with the joining ends and is faced for perfect fit. Fitting of one no. bend with the suction side of pump by P/F of rubber gaskets & nuts- bolts and then laying of the suction pipes with the fitting of other bend and flanged pipes as per the site requirement. All other pipes without flanges are to be circumferentially welded with each other after making proper alignment. Providing/Fitting of foot valve of 200 mm dia. with the flanged suction pipe with rubber washers & nuts-bolts after making proper alignment. Job also includes P/F of 3m 150mm dia MS delivery pipe by way of fitting of 1 no. 150mm sluice valve with proper flanges and 1 no. 150m reflux valves by fixing it with the flanges as per sample of reflux valve welded with pipe. Complete painting of M.S. suction, delivery pipe-lines & other exposed parts of 1Nos. Horizontal Centrifugal pump sets of 1 cusec discharge installed at LIS Kot-II by way of removing the rust/dirt from the outer surface of the pipes, bends, flanges, reflux valves, sluice valves, foot valves, nut & bolts by sanding away with emery/sand papers/steel wire brush, cleaning & making the surface smooth for painting then apply one coat of primer red oxide & two coats of black bituminous paint on all exposed parts. The job shall include cost of M.S. pipe Flanges, nuts & bolts and welding electrodes, hire & carriage charges for material, welding set & Oxy – acetylene gas equipment, tools and tackles required for the job, cost of carriage charges of M.S. Flanges etc., labour charges for skilled and semi-skilled labour. (Complete Job)

Providing /fitting, installation, testing and commissioning of protection panel cum star delta starters at L.I.S Kot-II Designing, fabrication, installation, testing and commissioning of LT control panel 415 volts, AC-3 Phase, 50 Hz, with one incoming and one outgoing for 20HP induction motors at L.I.S Kot-II. The panel shall be dust and vermin proof fabricated out of 16 SWG CR Sheet supported on M.S. angle of suitable size and having provision for fixing it on the ground with the help of foundation bolts. The panel should be sturdy enough for vibration free operation and should be equipped with suitable locking /sealing arrangements. The structure should be provided suitable entry and exit holes for incoming and outgoing cables. The panel should be given two coats of anti-rust primer and two coats of steel grey enamel paint. The panel should have equipped with following components / features: M.C.C.B.The panel incomer should be fitted with an M.C.C.B. of 100Ampere capacity, 1 no. volt meter, 1 no ammeter along with a set of CTs, 1 No. V.S.S., 1 No. A.S.S. and a set of RYB indicators at incoming side. Star delta Starter:.The panel should be fitted with 1 Nos MCCB of 100 Amp capacity, fully automatic star delta starter for unit comprises of 1 No. Main contactor of 100 Amp capaicty, 1 No. Delta contactor of 100Amp capaicty, 1 No. Star contactor of 50 Amp capaicty. 1 No. star delta timer with timing range from 3 to 120 seconds, 2 Nos. push buttons for start and stop operation of motor, 1 No. indicator ,1 No. MCB 6Amp for the protection of internal control wiring, a neat and clean internal control wiring should be made with flexible copper cables to complete the star delta circuit of out going supply for pumping unit. Protections device / fault analyzer: A protections devise / fault analyzer shall be fitted with the panel with capability to protect the motor by isolating the power supply of motor by de-energizing the starter/panel from following electro-mechanical faults which may otherwise damage the motor windings A. Voltage related fault: Single phasing, under voltage, over voltage, unbalance voltage. B. Current related fault: Over current / load, dry running, unbalance current / load, earth leakage, short circuiting. C. Mechanical fault: Locked rotor, broken shaft, a. Display line current of RYB Phase and also line voltage of RY and YB phase. b. Display and indicate trip status for over load, under load, single phase, unbalance, earth fault, over voltage, under voltage respectively. 2 Bimetal oveload relay :-A bimetal over load relay of suitable range should be fitted with in the starter as an extra protection to protect the motor in case of failure of fault analyzer with an isolation/bye pass switch to bye pass the fault analyzer. 3 Cable: Providing/ fitting of single core PVC aluminium cable 50mm2 of requisite length 30m (approx.) in length from VS to starter to motor. Complete job includes cost of providing/ fitting of material, transportation charges, hire charges, tool and tackles charges, hire charges of skilled and unskilled labour, To and fro transportation charges at site of L.I.S and all kinds of taxes thereof. (Complete job).

Providing and Carriage shifting of 600m(approx.) MS Pipe of diameter 150mm and 5.4mm thickness and then Laying of total 600m (approx.) of Rising main with allied works at Lift Irrigation Scheme Kot-II. The job involves loading of MS Pipes 150mm dia 600m in length with the help of manual labour as well as hydraulic crane on trucks, carriage of the same to site at LIS kot-II. Unloading the same at nearest unloading site by using manual labour as well as hydraulic crane and stacking the same properly. The job involves the excavation of trenches wherever required for laying 150mm dia rising main by way of engaging manual labour as well as all sorts of mechanical means, dressing of sides and ramming of bottom of trenches of excavated size (0.5m x 1m) 550 m in length approx. to maintain a steady gradient however the length, depth and width of the trench may varies as per site conditions, then Shifting/handling of 600m MS Pipes along the alignment of rising main by manual labor/hydraulic crane tractor trolley for laying of MS rising main 150mm dia, at Lift Irrigation Scheme Kot-II as per the alignment. The job includes clearing of debris, dunes etc lying along the path of alignment, stone cutting, removal of material like bushes, vegetation etc Laying of rising main includes lowering of pipes in the excavated trenches, circumferential welding of pipes with IS marked MS welding rods of the high quality and reliability to fill the V- groove between the pipes. Welding to be done by skilled workmen, handling of pipes with proper tools & tackles like tripod stands, chain pulley blocks or crane for holding of pipes during welding for proper alignment and then removal of slag before a new layer is put in place and afterwards, extra welded material is chipped off and cavities are filled. Negotiating bends of deviation less than 30º encountered during laying of M.S rising main. The laying of pipe includes fabrication of of bends as per site conditions (which may vary as per the site condition) along the line of alignment. The job may include anchoring of rising main with angle iron of requisite size wherever required as per site conditions. Providing fitting of 3 No double kinetic air release valves of 50mm dia, for 150mm dia rising main at a suitable place along the alignment of rising main Complete job include cost of material, transportation charges hire charges of oxy-acetylene gas cutting equipment, DG welding set & hydraulic crane, cost of POL's for DG welding set. Air release valves, MS Flanges, nuts & bolts, welding electrodes, hire & carriage charges for D.G welding set & Oxy acetylene gas equipment, tools and tackles required for the execution of job at site, labour charges for skilled and semi-skilled labour and complete testing of Pipe for any leakage on full load (Complete job)

Providing and Carriage shifting of 178 m(approx.) MS Pipe of diameter 300 mm and 5.4mm thickness then Laying of total 178 m (approx.) of Rising main along the alignment of already existing Rising main with allied works at Lift Irrigation Scheme Kot-II. The job involves providing, loading and carriage of MS Pipes 300mm dia 178m in length with the help of manual labour as well as hydraulic crane on trucks, carriage of the same to site at LIS Kot-II. Unloading the same at nearest unloading site by using manual labour as well as hydraulic crane and stacking the same properly. The job involves the excavation of trenches wherever required for laying 300mm dia rising main by way of engaging manual labour as well as all sorts of mechanical means, dressing of sides and ramming of bottom of trenches of excavated size (0.8m x 1m) and 170 m in length approx to maintain a steady gradient however the length, depth and width of the trench may varies as per site conditions and then Shifting of 178m MS Pipes along the alignment of rising main by manual labour/hydraulic crane tractor trolley for laying of MS rising main 300mm dia, at Lift Irrigation Scheme Kot-II as per the alignment. The job includes clearing of debris, dunes etc lying along the path of alignment, stone cutting, removal of material like bushes, vegetation etc Laying of rising main includes circumferential welding of pipes with IS marked MS welding rods of the high quality and reliability to fill the V- groove between the pipes. Welding to be done by skilled workmen, handling of pipes with proper tools & tackles like tripod stands, chain pulley blocks or crane for holding of pipes during welding for proper alignment and then removal of slag before a new layer is put in place and afterwards, extra welded material is chipped off and cavities are filled. Negotiating bends of deviation less than 30º encountered during laying of M.S rising main. The laying of pipe also includes fabrication of bends (which may vary as per the site condition) along the line of alignment. Providing fitting of 2No double kinetic air release valves of 50mm dia, for 300mm dia rising main at a suitable place along the alignment of rising main Complete job include cost of material, transportation charges hire charges of oxy-acetylene gas cutting equipment, DG welding set & hydraulic crane, cost of POL's for DG welding set. Air release valves, sluice valves MS Flanges, nuts & bolts, welding electrodes, hire & carriage charges for D.G welding set & Oxy acetylene gas equipment, tools and tackles required for the execution of job at site, labour charges for skilled and semi-skilled labour and complete testing of Pipe for any leakage on full load (Complete job)

KESARIMPEX (BID ID -2251591)

UEE Electrical Engineers Pvt. Ltd. (BID ID -2251614)