CA NO GE S U 27 2022 23 ADDN ALTN TO BUILDING NO NP-58 ALONGWITH ALLIED INFRA PROVN OF CEMENTED WASHING POINT WITH GEYSER CEILING PLASTER WALL FILLING AND REPLACEMENT OF KOTA STONE IN COOK HOUSE AT BUILDING NO P 141 AT 87 MTN BDE UNDER GE SOUTH UDH

Amount

Demolition of cement concrete in ground floor and paving n exc 15 cm thickness below and above ground level complete all as specified and as directed.

Demolition of reinforced cement work as in roof slabs (other than ground floors) beams stair cases, landing chajjas, drop facia and similar suspended work complete all as specified and as directed.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members at roof blankets complete all as specified and as directed.

Demolition of brick work or stone masonry built in cement mortar, or cement line mortar including all quoins, arches pillars etc. complete all as specified and as directed.

Surface dressing not exceeding 30 cm deep and averaging 15 cm in soft loose soil in road side berms including all necessary cutting / filling and finished to required size / shape complete all as specified and as directed.

Excavation in trenches n.exc 1.5M wide and n.exc 1.5M in depth for foundation complete all as specified and as directed.

Excavating over areas, n.exc 1.5m deep and getting out Hard Rock complete all as specified and as directed.

Anti-termite treatment of bottom and sides of excavation at the rate of 5 ltr of emulsion per square metre of surface area complete all as specified and as directed.

Anti-termite treatment of the top surface of filled earth at the rate of 5 ltr of emulsion per square metre of surface complete all as specified and as directed.

Anti-termite treatment of the soil under plinth protection at the rate of 5 ltr of emulsion per square metre of surface complete all as specified and as directed.

Providing and injecting Along the external wall below concrete or masonry apron using Antitermite Treatment chemical emulsion @ 2.25 litres per running metre including drilling and plugging holes etc. in apron complete all as specified and as directed. Note : The treatment work shall be carried through authorised agency only, and certificate for the same for warranty shall have to be furnished before submitting payment)

Providing and injecting Antitermite Treatment of soil under existing floors using emulsion @ 1 litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand to match the existing floors complete all as specified and as directed. Note : The treatment work shall be carried through authorised agency only, and certificate for the same for warranty shall have to be furnished before submitting payment)

Providing and injecting Antitermite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed. Note : The treatment work shall be carried through authorised agency only, and certificate for the same for warranty shall have to be furnished before submitting payment)

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated soil to a distance exc 50m and n.exc 1.50 km out side defence land complete all as specified and as directed.

PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and as directed.

Use & waste of form work to sides of concrete foundations footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified and as directed for fair finished surfaces.

Reinforced cement concrete Design Mix M-25 as in foundation including rafts, footing, plinth beams, bases for columns etc complete all as specified and as directed.

Form work to sides of columns rough ,Pillars, posts, struts, chajjas, roof beams etc suare or rectangular finished surfaces of concrete complete all as specified and as directed.

Reinforced cement concrete Design Mix M-25 as in columns, pillar, pier, posts, roof beams,chajjas etc complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, landing and similar work not exc 200mm thick complete all as specified and as directed.

Reinforced cement concrete M-25 nominal mix as in slab supported on walls , beam, and columns in floors,roofs landings, balconies etc. complete all as specified and as directed.

Reinforced cement concrete (Design mix) M -25 (using 20mm graded crushed stone aggregates) fins, fascias, louvres, parapets, and railings exc. 60cm in height, balustrade, and retaining structures complete all as specified and as directed.

Flat form work to fins, louvers, facia and parapet wall for rough finished surfaces of concrete complete all as specified and as directed.

Form work to sides and soffits of floor roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, over hangers etc also splays between floor and beam etc all as specified.for rough finished surfaces of concrete flat complete all as specified and as directed.

M & S TMT bars 10mm dia and over cut to length bent to shape reqd including cranking bending spirally for hooping for columns hooking ends and binding with MS wire annealed not less than 0.9mm dia complete all as specified and as directed. (Note : Site for brick work may involve head load , contractor shall have no claim on extra labour incurred in this account)

All as per Srl item No 26, but 6mm to 8mm dia complete all as specified and as directed.

Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar any description complete all as specified and as directed.

Brick work with sub class "B" bricks straight or curved on plan exceeding 6 Metre mean radius in cement mortar 1:4 complete all as specified and as directed.

Rendering 15 mm thick in CM 1:6 on brick work and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15 mm thick in two layers (10mm + 5mm) on fair faces of brick/concrete or stone surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete with water proofing compound complete all as specified and as directed. (WPC shall be measured separtely)

Rendering 10 mm thick in CM 1:3 on ceiling and exposed surface of concrete finsihed even and smooth without using extra cement complete all as specified and as directed.

New plaster surface of walls surface and applying two coat of plastic emulsion paint (Shade to be approved by GE) over two coat of wall care putty with primer complete all as specified and as directed.

Preparation of new plaster surfaces of wall and applying two coats of weather proof exterior emulsion paint (APEX or equivalent) over a two coat of wall care putty with coat of primer etc complete all as specified and as directed.

Preparing new ceiling surface and apply two coat of oil bound distemper over two coat of wall care putty with one coat of primer complete all as specified and as directed.

Complete removal of existing treatment of wall surface and applying two coat of plastic emulsion paint (Shade to be approved by GE) over two coat of wall care putty complete all as specified and as directed.

Complete removal of existing treatment (using removal machine) including preparing surfaces of wall and applying two coats of weather proof exterior emulsion paint (APEX or equivalent) over a two coat of wall care putty with a coat of Primer up to G+1 floor height etc complete all as specified and as directed.

Complete removal of existing treatment of wall two coat of wall care putty and applying two coats of oil bound distemper over a coat primers with complete all as specified and as directed.

All as per Srl item No 38, but on ceiling complete all as specified and as directed.

Hard core of guage n exc. 63 mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

Sand cushioning/filling under floors or laying as per site requirement complete all as specified and as directed.

75 mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base of floor etc complete all as specified and as directed.

50 mm thick PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregates) as in floors laid in alternate pannels finished even and smooth without using extra cement complete all as specified and as directed.

15 mm thick screed bed in cement mortar 1:6 for laying floor finishes under floor complete all as specified and as directed.

Marble slab 20 mm thick machine cut, marble slab, (Makrana white ), as in flooring, bedded jointed with grey cement slurry and pointed with white cement including cutting and polishing complete all as specified and as directed.

Marble slab 20 mm thick machine cut, marble slab, (Makrana black /green ), as in flooring, bedded jointed with grey cement slurry and pointed with white cement including cutting and polishing complete all as specified and as directed.

75 mm thick cement concrete 1:3:6 type C-2, (using 20mm graded crushed stone aggregates) as in plinth protection finished fair and even with using extra cement complete all as specified and as directed.

Framed work such as grill, gratings, etc with ends of bars shouldered and/or riveted or forged in to spikes, framed guard bars, barred iron doors ladders framed balusters and similar work conforming to Fe 290 Gde E-165 complete all as specified and as directed.

First class hard wood plain solid straight chowkats and frames and Design main doors Pannel shutter with wrought framed on the solid rounded or chamfered put together with glue and pinned at joints including preservative treatment all as specified and directed to approved by GE.

Supply and fixing 40 mm thick flush shutter (Both side decorative) solid core consturction with particle board core and plywood face panels on both side and both face is covered with decorative face veneer with lipping/frame to match complete all as specified.

Supply and fixing Solid (wood grain printed) PVC door frame of size 50 mm x 47 mm made of 5 mm wood grain printed PVC sheet reinforced with mild steel square tube and & edges will be painted to match with printed shee complete all as specified and as directed

Supply and fixing Factory made wood grain printed , solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded wood grain printed PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of wood grain printed PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails ,5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet and jointed together with solvent cement, supply and fixing in the frame at site as specified in relevant SSR complete all as specified and as directed.

Supply & fixing 18 mm thick plain PVC board medium density such as Rajshree celuka ply complete all as specified and as directed. ( Make - Rajshree or equivalent)

18 mm thick prelaminated wooden grain PVC board medium density such as Rajshree celuka ply complete all as specified and as directed. (Make - Rajshree or equivalent)

Sliding rails for drawers complete all as specified and as directed.

Stainless steel trolly for drawers complete all as specified and as directed.

Supply only cabinet hinge spring self closing type complete all as specified and as directed.

100 mm stainless steel decorative drawers/ cabinet handles complete all as specified and as directed.

150 mm brass barrel tower bolts,with cast or sheet and rolled or cast bolts complete all as specified and as directed.

Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts 300 mm complete all as specified and as directed.

125 But hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type C-12 complete all as specified and as directed.

150 mm length Brass handles, cast type, polished bright Extruded brass handles, fabricated type polished complete all as specified and as directed.

French polishing on surfaces of any description width or girth including cleaning and prepairing the surface including a coat of wood filler on new works with two or more coats complete all as specified and as directed.

Preparing new/old wooden surface & applying two coats of synthetic ennamel paint over a coat of pink primer over 10cm width or girth complete all as specified and as directed.

18/19mm thick plywood, grade 1 (with BWR resistance/termite proof) with screws to timber frame work as in cup boards/cabinets etc complete all as specified and as directed. Make : Century/kitply or equivalent.

12mm thick plywood, grade 1 (with BWR resistance/termite proof) with screws to timber frame work as in cup boards/cabinets etc complete all as specified and as directed. Make : Century/kitply or equivalent.

0.9mm thick decorative choice of lamination type-1 of surface finish white stuck with imported adhesive on sides of board complete all as specified and as directed. Make : Corby/Euro

All as per Srl item No 67, here-in-above but designer type with matic finish 1.5mm thick complete all as specified and as directed. Make : Corby/Euro

6.4 mm thick bevelled edge glass of area n exc 0.5 Sqm each as in shelves of size and shape as required at site complete all as specified and as directed.

Stainless steel clamps capable of supporting glass shelves of max width 100 mm complete all as specified and as directed.

Continuous (piano) hinges, mild steel, bright finish or elecro galvanised width of flaps when open in 30mm and fixed complete all as specified and as directed.

100mm long extruded brass handle polished bright complete all as specified and as directed.

Designer brass barrel tower bots of size 100mm (ISI Marked) including screws and fixed complete all as specified and as directed.

Brass mortice lock 30mm long for 4 leyer cup boards complete all as specified and as directed.

Brass hasp and staple size 100mm powder coated with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

Brass 40 mm dia, cupboard knob fixed with nut, screw and washer of mild steel, brass polished bright finished complete all as specified and as directed.

Roughening surfaces of concrete floor by picking sweeping cleaning & washing down with water to remove dust etc including removal of Old/New treatment of any description and applying one coat of neat cement slurry @ 3.00 kg/Sqm complete all as specified and as directed.

Cutting grooves to a depth 75mm and 100mm height in columns of water tank base and after tucking in of roof treatment sealed with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) and making curve complete all as specified and as directed.

PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in level course on roof surface 25mm thick etc complete all as specified and as directed.

Rendering 10 mm thick in CM 1:3 mixed with integral water proofing compound as per manufacture's instructions as in roof and chajjas, and drop facia finished the surface fair and even with out using extra cement complete all as specified and as directed. (Note : Supply of water proofing compound will be measured and paid separately .)

Applying bituminous primer on roof surfaces @ 0.40 ltr/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm and provide modified polymeric five layered APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polythylene film. Min wt of membrane will be 3.5 kg/sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm blinded with fine sand in dry condition @ 0.5 kg/sqm including two coats of bituminious alluminium paint complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

PCC 1:2:4 type B-0 (using 12.50 graded crushed stone aggregates) for coping, corner of roof and similar work complete all as specified and as directed.

110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and as directed.

110 mm PVC (SWR) bends any radius with access door complete all as specified and as directed.

Material and labour ultra charged/double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and joints filled by epoxy complete all as specified and as directed.

Material and labour ultra charged/double charged Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 Sqm , in skirting / dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and joints filled by epoxy complete all as specified and as directed.

110 mm PVC (SWR) couplers for pvc pipe and similar work complete all as specified and as directed.

Aluminum door closer ( aluminum extruded section) hydraulically regulated , designation No 3 , universal type , suitable for door shutters of 851mm to 1000 in width and of weight 61 to 80 kg complete all as specified and as directed.

Harrison, rails drapery rod powdered coated including brackets and necessary fitting complete all as specified and as directed.

Non skid coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11Sqm but not exc 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and joints filled by epoxy complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Rendering 10mm thick on fair faces of brick work or concrete surface in CM 1:4 on vertical surfaces/backing coat mixed with approved adhesive and joints filled by epoxy complete all as specified and as directed.

Glazed ceramic coloured tiles of size 600mm x 1200mm x 10mm wall set and jointed in neat cement and in white/coloured cement to match with the colour of tile and joints filled by epoxy etc, complete all as specified and as directed.

S&F in repairs water closet wall mounted pattern colour as approved by Garrison Engineer complete all as specified and as directed. Make SOMANY CAT PART No (EWC 120305) cistern 120714 Seat cover 121311 Twin flush cistern 120627) UNIEK

WHB coloured 615mm x 510mm with pedestal complete all as specified and as directed. Make CERA CARNIVAL Cat Part No (WHB 1009, PEDESTAL 1108)

CP wastecoupling 32mm dia PTMT (half or full threaded) minimum weight 450 gms complete all as specified and as directed.

PVC waste pipe 32mm bore with cup and washers complete all as specified and as directed.

15mm bore centre hole basin mixer with round spout with 450mm long copper pipes and brass nuts with out Pop up complete all as specified and as directed. Make: Jaquar Cat Part No CON 167KNB

15mm bore Bib tap complete all as specified and as directed. Make Jaquar Cat Part No CON-107KN

15mm bore Angular stop cock with wall flange complete all as specified and as directed. Make: Jaquar Cat Part No CON- 059KN

PVC connection 15mm bore 450 mm long Braided Hose with M10X1 Nipple, 15 mm Nut, O-Ring & Rubber washer (Suitable for Basin Mixers) complete all as specified and as directed. Make: Jaquar Cat Part No ALD-803AB

PVC connection 15mm bore 450 mm long Braided Hose with two 15 mm Nut & Rubber washer without nipple complete all as specified and as directed. Make: Jaquar Cat Part No ALD-805B

Chromium plated toilet paper holder complete all as specified and as directed. Make Jaquar at Cat Part No ACN 1153N

Glass shelf with chromium plated guard rails complete all as specified and as directed. Make Jaquar Cat Part No ACN-1171N

600 mm long brass chromium plated towel rail fancy type complete all as specified and as directed. Make Jaquar Cat Part No ACN-1111NM

Soap dish complete all as specified and as directed. Make Jaquar Cat Part No ACN 1131N

Double Coat hook complete all as specified and as directed. Cat Part No ACN 1161N

Powder coated Aluminium frames for doors, windows, ventilators with one or more rebates and aluminium window and ventilator shuttter frames jointing cleats for fixing and partation wall frame etc thickness of powder coating not less than 50 micron complete all as specified and as directed. Note : Powder coated aluminium coating colour as approved by GE.

Door frame of size 95.25 mm x 44.50 mm x 1.70 mm @ 1.301 Kg/RM.

Shutter vertical member 85 x 44.50 x 1.56 mm @ 1.39 Kg per RM

Shutter top member 83.50 x 44.50 x 1.54 mm @ 1.139 Kg per RM.

Shutter bottom member 101.60 x 44.50 x 1.60 mm @ 1.301 Kg per RM.

(e) Shutter lock rail member 83.50 x 44.50 x 1.54 mm @ 1.139 Kg per RM. The actual measurement shall be taken, wastage shall be including in the rates, the above sections are from JINDAL/INDAL/HINDAICO/WALCO extruion. The contractor is at liberty to choose high section from approved make with minor variation in sizes and weight as approved. However nothing extra shall be paid for over size and over weight section also.

Taking down frames with shutters (without taking off shutters from the frame ) area not exc 1.5 Sqm Each including iron mangery complete all as specified and as directed.

100mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) as in foundations filling and mass concrete complete all as specified and as directed.

Coloured machine vibro mechenically floated glossy finish interlocking cement paver block,any shape and size confirming to IS 15658-2006 of 60mm thickness,M-35 Grade with,topping of cement mixed with imported pigment,colour and shape shall be approved by Garrison Engineer. ISI Marked.

Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneelers apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles as directed, 1:2:4 mix type B-0 complete all as specified and as directed.

25mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in floor and finished even and fair complete all as specified and as directed.

Screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 laying floor finishes complete all as specified and as directed.

Dura stone tiles of size 305mm x 305mm x 10 mm thick as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surface of tiles complete all as specified and as directed. Note :Shade/colour as approved by GE)

Providing precast cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, kneelers apex stones , bed plates, kerbs stone provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 complete all as specified and as directed.

Excavation in trenches n.exc. 1.5 m wide and n.exc. 1.5 m in depth for foundation or manholes etc, and area n.exc.10 Sqm on plan and getting out in any type soil complete all as specified and as directed.

SWG drain pipe grade 'A' of 150 mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified and as directed.

Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete type D-2 (1:4:8) for 150mm dia pipe complete all as specified and as directed.

Precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) for manhole cover septic tank covers slabs etc including necessary form work and set in CM (1:4) complete all as specified and as directed. (Note:- reinforcement will be measured and paid seperately.)

PVC (SWR) junction single (single T) equal or unequal 110 mm dia with access door complete all as specified and as directed.

110mm bore (SWR) vent cowl complete all as specified and as directed.

PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) as in surface channel and drains including necessary formwork and extra forming fair finsished drain or channels for inner girth in cement concrete etc complete all as specified and as directed.

S & F reinforced concrete pipes, class NP2 as in repair bore of pipe 150 mm laid and jointed complete with collars complete all as specified and as directed.

PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in plinth protection laid in alternate pannels, finished even and smooth without using extra cement complete all as specified and as directed.

Walling of random rubble,uncoursed,well bonded,bedded and solidly hearted built in cement mortar 1:6 complete all as specified and as directed.

Walling of random rubble,uncoursed,well bonded,bedded and solidly hearted built in cement mortar 1:6 but except stone complete all as specified and as directed.

Precast cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone agregates) bonders for stone walling set in cement mortar 1:6 with plain fair faces including chamfers weathering etc complete all as specified and as directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified , with maximum depression on face from straight edge n. exc 40mm for lime or sand stone complete all as specified and as directed.

PVC (SWR) pipe, 110mm dia (ISI marked) in any length embedded in cement mortar for weep holes at locations complete all as specified and as directed.

Raised pointing to random rubble masonry, uncoursed or brought upto courses in cement mortar 1:4 complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B-2 (using 40 mm graded crushed stone aggregates) as in channels and drains, foundation and similar work etc complete all as specified and as directed.

PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in coping, benching and similar work etc including necessary form work complete all as specified and as directed.

300 mm dia Reinforced concrete pipes, class NP-2 laid and jointed complete with collars complete all as specified and as directed.

Cement concrete 1:4:8 type D-2 for concrete bed to 300 nmm dia RCC drain pipe including packing under and haunching against the sides of pipes after they are laid & testing complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in slab supported on walls/chajjas and the like complete all as specified and as directed.

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping complete all as specified and as directed.

Vitrified dark shade tiles 10 mm thick (square/rectangular) area of each tile not exceeding 0.38 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Glazed coloured ceramic tiles in dado/vertical surface (300mm x 450mm x 7mm) /(300mm x 600mm x 7mm)/ thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and as directed.

Screed bed or bedding layer of mortar 20mm thick in cement mortar 1:4 laying floor finishes complete all as specified and as directed.

Machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Machine cut kota stone slab flooring 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

150mm wide strip of makrana white marble 20 mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types complete all as specified and as directed.

Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

Preparation of new surfaces and applying two coats of Cement base paint on walls complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt ), complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and as directed.

Pressed steel frames for doors made out of 1.25mm thick MS sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate 12mm bar thresh hold etc. complete , of frame size 125mm x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and as directed.

Pressed steel frames for doors made out of 1.25mm thick MS sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate 12mm bar thresh hold etc. complete , of frame size 105mm x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and as directed.

Factory made, 2nd class hard wood 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

Factory made, 2nd class hard wood 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauze etc complete all as specified and as directed.

Welded steel wire fabric mesh weight n.exc 4 Kgs per sqm fixed to steel members complete all as specified and as directed.

Rolled mild steel work of angle iron as in frames of doors & Cup Board etc conforming to grade Fe 410-O or Fe-310-O complete all as specified and as directed.

Providing cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) for filling in the pressed steel door frame/hold fast complete all as specified and as directed.

75mm butt hinges ,medium weight ,cold rolled mild steel complete all as specified and as directed.

18/19 mm thick block boards grade 2 quality enterior grade, Commercial type fixed with screw or Steel fram/Timber frame incl teak wood lipping,6mm thick fixed with Nail complete all as specified and as directed.

100mm size hasp and staple safty type aluminum anodized with mild steel hinges pin including bolt to hinge plate and fixed with screw complete all as specified and as directed.

Mild steel, 150 mm, ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified and as directed.

4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

Galvanised Mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

150 mm aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

150 mm aluminium handles, cast type anodised complete all as specified and as directed.

Aluminium drapory rods of 25 mm dia decorative type with wooden finish alongwith holding for brakets & end caps in repairs complete all as specified and as directed.

Preparation of steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of zink chrome primer complete all as specified and as directed.

Brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:6 bricks complete all as specified and as directed.

Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and as directed.

Providing 50 mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) as in plinth protection laid in alternate bays (n.exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed.

S&F in repair vitreous China wash basin, white, flat back , size 550mmx 400mm excluding tap, chain, plug but including brackets, waste fitting 32mm dia ,brass chromimium plated for glazed ware sink, basin,with pedestal, long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified.

Aluminium tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodized, fixed with rawl plugs. complete all as specified and as directed.

Taking down 15mm Bore steel tubing and connections including all fittings and removing to store complete all as specified and as directed.

Taking down 20mm Bore steel tubing and connections including all fittings and removing to store complete all as specified and as directed.

15mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls including cancealed and or laid under floors etc complete all as specified and as directed.

20mm bore galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified and as directed.

S&F in repairs Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15mm complete all as specified and as directed.

S&F in repairs Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20mm complete all as specified and as directed.

S&F in repair chromium plated cancealed stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions chromium plated of size 15 mm complete all as specified and as directed.

S&F in repairs Pillar tap, cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed of bore dia 15 mm complete all as specified and as directed.

S&F in repairs Bib tap cast copper alloy with crutch or butter fly handle screwed down screwed for iron pipe of size 15 mm bore chromium plated complete all as specified and as directed.

S&F repairs Ball Valves high pressure 20 mm bore of pipe of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 20 mm- 210 grms complete all as specified and as directed.

Dismantling water tanks exc 500 Ltr capacity but n.exc 1000 ltr complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks with thereded head ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 liter including all accessories complete all as specified and as directed.

Supply and fixing 15 mm bore chromium plated concealed stop cock fancy type long shank and cup complete all as specified and as directed.

Soap dish chromium plated fixed with brass screws and wooden/plastic cleats complete all as specified and as directed.

PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as specified and as directed.

Point wiring for one light/ fan/ Exh Fan point controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5mm and 20mm dia), medium grade with Modular metal flush boxes & metal back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5Sq mm as earth wire stranded and conected to earth dolly complete all as specified and as directed. Make: Finolex/ Polycab

All as per Srl item No 195, but for 3 pin 5 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 Sq mm earth wire and connected to earth dolly. complete all as specified and as directed.

All as per Srl item No 195 but for 3 pin 5 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 Sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 195 but for 3 Pin 15 Amps socket outlet independent with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 Sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 195 but for 3 Pin 15 Amps socket outlet independent with cable 4.0 Sq mm including copper PVC insulated PVC unsheathed 2.5 Sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

Switch Piano flush type 6 Amps single pole one way (Modular Type) with outer strip complete all as specified and as directed.

Switch Piano flush type 16 Amps single pole one way (Modular Type) with outer strip complete all as specified and as directed.

Socket 3 Pin 6 Amps flush type complete all as specified and as directed.

Socket combined 2-in-1, 3 Pin 6 & 16 Amps flush type (Modular Type) with outer strip complete all as specified and as directed.

Call bell ding-dong 230 volts including taking down old one complete all as specified and as directed.

Single pole and neutral enclosure surface mounted 240 volts with 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator complete all as specified and as directed. Make: Legrand/ Havells/ Anchor.

Electronic step type fan regulator 120 watt 230 volts 50 C/S deluxe modular type complete all as specified and as directed.

Ceiling rose, surface bakelite 65mmx 50mm two to three terminals fixed on PVC Round Block complete all as specified and as directed.

Bell Push, 6 Amp, 230 Volts, 1 Modular type complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing LED Downlighter 12Watt slim, compact, aluminum die cost edge lit panel. Surface/ Recess mounted round fixture with opal diffuser and separate electrtonic driver complete all as specified and as directed. Make- Havells Cat Part No - LHEBHDP5IZ1W012 (Colour: Warm White/ Off White/ White)

Supply and fixing LED Downlighter 03 Watt slim, compact, aluminum die cost edge lit panel. Surface/ Recess mounted round fixture with opal diffuser and separate electrtonic driver complete all as specified and as directed. Make- Havells Cat Part No - LHEBHDP5IZ1W003 (Colour: Warm White/ Off White/ White)

Supply and fixing 7.5 Watt A60 LED Filament Lamp wall mounting, anique brass finish fixture with opal glass diffuser suitable for E27. Make- Havells Cat Part No - LHFOAJD1TZ1T060 (Colour: Warm White/ Off White/ White) complete all as specified and as directed.

Supply and fixing 9W LED fitting with LED Lamp wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 Base complete all as specified and as directed. Make: Havells.Cat Part No - LHFOAJE1TN1I060 (Colour: Warm White/ Off White/ White)

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure diecast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

S & F in replacement sheet metal enclosures for DBs when MCBs to be used double door DB VTPN MCCB 125A 4way IP43 Protection Make: Indoasian, Cat Pt No - 811888 with 125A MCCB 16kA complete all as specified and as directed. Make: Indoasian, Cat Part No - 830153 or equivalent to Make : Indoasian/Legrand/C&S

Sheet metal enclosures for DBs when MCBs to be used double door DB SPN 12 way 240 volts with 200 Amps rated bus bar and neutral link including chases wall for dixing DB and making good distributed wall surfaces to match with existing specification or equivalent Legrand/ Anchor complete all as specified and as directed.

Sheet metal enclosures for DBs when MCBs to be used double door DB SPN 08 way 240 volts with 200 amps rated bus bar and neutral link in cluding chases wall for dixing DB and making good distributed wall surfaces to match with existing specification or equivalent Legrand/ Anchor complete all as specified and as directed.

S&F in replacement MCB Single Pole, 230 Volt, Rating 10 to 40 Amps, C Curve complete all as specified and as directed. Make: Legrand/ Indoasian/ Anchor.

S&F in replacement MCB Single Pole and Neutral , 230 Volt, Rating 63 Amps, C Curve complete all as specified and as directed. Make: Legrand/ Indoasian/ Anchor.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 4 Sq mm as earth lead complete all as specified and as directed including taking down old sub main wire.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead complete all as specified and as directed including taking down old sub main wire.

Taking down ceiling fan of any size after disconnecting the wire from existing ceiling rose and depositeed to MES Store (AGE E/M sub Divn) and Supply & fix ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with burshless direct current motor (BLDC) complete all as specified and as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electode 600mm x 600mm x 6.00mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-1 angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mash and light grade GI protection pipe 15mm bore upto main board complete all as shown in electrical plate No 3 of MES SSR 2009 (Part I) connected to main control board as specified and testing on completion complete all as specified and directed.

Point wiring for one light point /fan point/ bell point controlled by one switch with 1.5 sqmm PVC insulated FRLS unsheathed copper conductor single core multi stranded flexible copper cable 1100V grade in and including not less than 2.00 mm thick and 20 mm dia Non metallic Rigid PVC surface/Concealed Conduit ( ISI marked ) with and all accessories 1.5 mm thick mild steel terminal boxes concealed on walls, painting the same inside and out side with one coat of black bitumen paint with 3mm thick hylam brand bakelite sheet cover for fixing of piano switches/sockets/ regulator etc along with PVC insulated and unsheathed FRLS 1.5sqmm multi stranded copper conductor cable (green color) as earth lead, & connected to common earth and earthdolly, making good the disturbed surface to match with the existing specification complete all as specified and as directed. Make- Polycab or equivalent make in Havells/finolex

All as per Ser Item No.226 here-in-before but for one 3 pin 5 Amp socket outlet point controlled by one push button on same board, complete all as specified and as directed. Make- Polycab or equivalent make in Havells/finolex

All as per description of Ser Item No.226, here-in-before but for one 3 pin 5 Amp socket outlet point controlled by one push button on independent board complete all as specified and as directed. Make- Polycab or equivalent make in Havells/finolex

All as per Ser Item No.226 here-in-before but for one 3 pin 15A socket outlet on independent Board with PVC insulated unsheathed FRLS cable 4 sqmm copper multistrand conductor, along with PVC insulated and unsheathed FRLS 2.5 Sqmm multistrand copper conductor earth wire connected to common earth and earth dolly complete all as specified and as directed. Make- Polycab or equivalent make in Havells/finolex.

S&F in repair Switch piano flush button single pole one way 5 amps 240 volt complete all as specified and as directed.

S&F in repair Socket outlet 2 in 1, 3 pin, 5A, 240 Volt complete all as specified and as directed.

S&F in repair Switch socket combination 5 Amps 2-in-1, 5 Pin flush type, 230 volts complete all as specified and as directed.

S&F in repair Switch socket combination 5 pin 16 Amp, flush type complete all as specified and as directed.

S&F in repair Ceiling rose surface bakelite 3 terminals complete all as specified and as directed.

S&F in repair fan regulator electronic, stepped type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and as directed.

Taking down ceiling fan/Exhaust Fan including disconnection of existing connection, dismanting of blades and Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and rehanging the fan complete all as specified and as directed.

Taking down carefully & re-fixing existing LED Tube lights fittings connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F in replacement Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed. (Note-MCBs will be measured separately)

S&F in replacement MCB Single Pole, 230 Volt, Rating 05 to 32 Amps complete all as specified and as directed. Make: Legrand/ C&S /Indoasain.

S&F in replacement MCB Single Pole and Neutral , 230 Volt, Rating 32 Amps complete all as specified and as directed. Make: Legrand/ C&S /Indoasain.

S&F in replacement MCB Single Pole and Neutral , 230 Volt, Rating 40 Amps complete all as specified and as directed. Make: Legrand/ C&S /Indoasain.

VTPN DB Double Door Including MCCB 100Amp, 16 kA (as Incommer) 4 Way double door complete with appropriate size bus bar, neutral link and Earth Bar fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed. Make- Indoasian/Legrand/Havells

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 4 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 2.5 Sq mm as earth lead complete all as specified and as directed. (For Geyser power point)

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 2.5Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 1.5Sq mm as earth lead complete all as specified and as directed. (For bldg security light)

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.30 mm thick buried directly in ground (earth pit not less than 2.25 Mtrs below normal ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead 4 mm dia by means of bolts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point complete all as specified and as directed, indicated and testing on completion including excavation earth work drilling holes for electrode PCC pit & cover, funnel, water pipe lugs GI pipe medium grade protection pipe for earth lead up to DBs complete all as specified and as directed.

Supply and fixing exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and as directed.

Supply & fixing Geyser (Water heater) storage type, Electric 230V, SP, AC complete of capacity 25 Ltrs including all GI connection (cutting T, inserting all type of Elbow, Nipple, bib tab etc) and PVC pipe length 600mm- 02 Nos all necessary fixing arrangement complete all as specified and as directed. Make - Make - Havells(Monza) or equivelent make Bajaj/Recold

S&F in repalcement of LED street Light fitting 30 Watt, New generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 with acrylic, with Heat resistant toughened Glass, Corrosion resistant, complete making all connection with MCB SPN alongwith MCB Box enclosure complete all as specified and as directed. Make- Havells Cat Part No- ENDURAPEARLSL30WLED757SASYTOPCMP (ENDURA PEARL 30W MP)

Street light Bracket complete made of GI pipe of suitable size of 25 mm dia, medium grade 1.2 m long bent to shape as per site requirement along with MS flat iron clamps with nuts, bolts, washers including grouting the same with wall ,including taking out old bracket complete all as specified and as directed.

S&F in replacement of Sheet metal enclouser single pole and neutral with 2 pin and earth plug and socket 20A 240V complete with one single pole MCB of any cap from 10Amp to 20Amp, 10KA complete all as specified and as directed.

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmm x 3.5 core size including taking out old unsv UG cable any type/size complete all as specified and as directed.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and as directed. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and as directed.

Supply and fixing GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and as directed.

Removing excavated material (Soil) toadistance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and as directed.

M/s LAL DAYAL CONSTRUCTION CO

RAMAN CONSTRUCTION CO

M/S ASHOK KUMAR PACHIALA

joginder singh and sons