GE/PNH-10/2021-22

Amount

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

Dismantling of timber scantling under 40sqcm in section unframed work as in fillets, rails, posts, rafters, purlins etc , complete all as specified and directed.

S&F Suspended false ceiling using E- grid suspended ceiling grid system of grid size 600x600mm with GI frame work of main runner 38 x 24mm sheet thickness 0.4mm, cross Tee 28 x 24mm sheet thickness 0.3mm and wall angle 24 x 24mm x 0.4mm using 4mm thick high pressure stream cured classic variant E-board, designer pattern (ISI marked, IS No 14862-2000) & E board to be placed in the grid suspended by 4mm GI wire hangers from the purlins of the roof with butter fly clips, complete all as specified and directed. Make:- Everest Industries Ltd of equivalent as approved by GE.

M&L for 50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base floor finishing surface even and fair, complete all as specified and directed.

M&L for Cement concrete (1:2:4) type-B-1 (using 20mm graded stone crushed aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, bed block, kneelers, apex stones, bed plates, roof kerbs round or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for Chequered cement concrete tiles 300x300x 25mm thick, set, jointed and pointed with mixture of white and grey cement in equal proportion and no pigments, laid over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for Vitrified ceramic tiles 10 mm thick (square/rectangular) area of each tile but not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

All as per ser item No.12 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11Sqm but n exc. 0.18Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed

All as per ser item No.14 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for Glazed ceramic coloured tiles (300x200mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

M&L for Walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

All as per item No.19 above, but except stone complete all as specified and directed.

Extra over stone walling of random rubble walling, uncoursed or brought for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified and directed.

M&L for Rendering 20mm thick on other than fair faces of brick work or stone masonry surfaces in cement mortar 1:4 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick cement plaster rendering in CM 1:4 on fair faces of bricks or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on other than fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for Preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

M&L for Preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil emulsion distemper over and including 1-2mm thick wall care putty, complete as specified and directed.

M&L for Applying three coats of white wash including preparation of newly plastered surfaces of wall complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Dismantling of timber scantling 40sqcm and over in section, as in any position, complete all as specified and directed.

S&F 0.63mm thick galvanised corrugated mild steel sheeting with grade of Zinc coating of 275 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with L or J type or cranked hook bolts, in roof, walls etc, complete all as specified and directed.

All as per item No. 31 above, but except sheeting, complete all as specified and directed.

S&F 0.80mm thick plain galvanised mild steel sheeting with 275 gm/sqm Zinc coating as in ridge , hips, valley gutters, drip and straight flashing fixed with L or J type or cranked hook bolts, in roof etc., complete all as specified and directed.

S&F Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connected plate confirming to Fe 410W(Gde E-250), quality 'A' complete all as specified and directed.

S&F Mild steel work as in wind ties for roof including securing bolts, including all necessary drilling, bolting or riveting etc. fixed in repairs, and similar work conforming to Fe-250 Gde E-165 complete all as specified and directed.

S&F 2nd class soft wood (Kail) as in scantling, clean sawn fixed in unframed work, complete all as specified and directed.

Taking down shutters of any description exceeding 1sqm and not exceeding 2sqm each, complete all as specified and directed.

Taking down shutters of any description not exceeding 1sqm each, complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5Sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each, complete all as specified and directed.

S&F 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

S&F 35mm thick 2nd class hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc divided into square (with sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F 30mm thick 2nd class hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (divided into square with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b) supplied and fitted to chowkats complete all as specified and directed.

S&F Factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, fixing in frame at site complete all as specified and directed.

S&F Mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

S&F Mild steel butt hinges, medium weight, cold rolled,75mm long, complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of extruded section of size 100mm and fixed, complete all as specified and directed.

S&F Aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S&F Aluminium alloy handles, cast type, anodised of size 100mm and fixed, complete all as specified and directed.

S&F 250mm long aluminium alloy anodized sliding door with haps, staple (bolt type) and fixing clips of sheets, cast or extrusted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

S&F 300mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of Ist quality over a coat of pink primer, complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

S&F Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair Bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. Make:- Jaquar cat part No CON-047KN or equivalent cat part of make as specified in P.S.

S&F in repair Angular stop valves cast copper alloy 15 mm dia, fancy type, chromium plated with wall flange screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions complete all as specified and directed. Make-Jaquar Cat Part No:-CON-059KN or Equaivalent cat part of make as specified in P.S.

S&F in repair Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed. Make:- Prayag cat part No4054 or Equaivalent cat part of make as specified in P.S.

S&F in repair PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints complete all as specified and directed. Make:- Prayag cat part No 501 or or Equaivalent cat part of make as specified in P.S

S&F in repair Vitreous china wash hand basin, white, flat back, size 550x400 mm excluding taps, waste, chain & plug and porcelain stopper but including brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed. Make-Prayag Cat Part No:-4645 or Equaivalent cat part of make as specified in P.S.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 450mm complete all as specified and directed.

S&F in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe complete all as specified and directed. Make:- Jaquar cat part No CON-011KN or equivalent cat part of make as specified in P.S.

S&F in repair 32mm dia PVC corrugated waste pipe 800mm long complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe including clamps, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe(vent pipe) including clamps,, complete all as specified and directed.

S&F in repair Vitreous china urinals, bowl type of size 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and waste pipe),complete including poviding and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing with automatic flushing cistern with brackets, flush pipe, waste pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repair Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), fixed, suitable for floor taps, complete all as specified and directed.

Dismantling PVC water tanks and removing to storing of capacity not exceeding 500 ltr complete all as specified and directed.

Dismantling PVC water tanks and removing to storing of capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms), complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone/ concrete, glazed with putty or fixed with beads, complete all as specified and directed.

S&F Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

S&F Figured glass pin headed type, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading complete all as specified and directed.

M&L for Applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

S&F in repair MS powder coated tubular curtain rod fancy type of 25mm dia complete all as specified and directed.

S&F MS powder coated decorative type bracket, end ball, rounded block, bracket (coated with brown/ cherry/ golden colour) suitable for 25mm dia curtain rod of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed.

S&F Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for Plain cement Concrete 1:3:6 type-B1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work, complete all as specified and directed.

S&F in repair Chromium plated Hand shower (Health faucet) with 1.5m long flexible tube of stainless steel in chrome finish and wall hook complete all as specified and directed. Make: Jaquar code No ALD-CHR-583 or equivalent cat part of make as specified in PS.

S&F in repair CP, jet spray with holder including 1.5m long PVC/Chromium plated flexible PVC pipe, necessary nut bolts and PVC washers fixed with PVC seat cover for pedestal pattern water closet, complete all as specified and directed.

S&F in repair Plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised or PVC hinging device, complete all as specified and directed.

S&F in repair PVC water tank cover suitable for 500ltrs/1000ltrs water tank, complete all as specified and directed.

Taking down existing roof treatment of any description in any condition including removing of cement plaster of concrete of any description from the roof surfaces and removing all the debris to a distance n.exc 100m and roughening surfaces by sweeping clean and washing down with water to remove dust etc and applying evenly cement slurry at the rate of 3 Kg/Sqm over cleaned surfaces and providing 10 mm thick cement screed in CM 1:4 mixed with liquid water proofing compound Pedilite LW plus @ 200 ml per 50 Kg of cement finished surface even and smooth for laying of water proofing membrane (Note : WPC will measured and paid separately as supply only), after that cleaning the entire roof surface thoroughly to remove all loose particles, dust/dirt particles and applying with one coat of industrial bituminious primer at the rate of 0.40 lit/Sqm over the plastered surfaces of roof, and applying a course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180 0 C @ 1.2 kg/sqm then applying APP based polymeric membrane minimum weighing ....contd to item No-90.01

3 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/sqm) laid with 75 mm side overlap and 150 mm overlap primed surfaces by forced (tourch) application as per manufactures instructions and applying two coats of aluminium paint over APP membrane, complete all as specified and directed.

Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight), complete all as specified and directed.

Cleaning / disinfecting of PVC / RCC water storage tank of any capacity with disinfecting chemicals (Chlorine) properly with water thorioughly flushed out, complete all as specified and directed.

M&L for Preparation of old plastered/ un-plastered wall surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying one coat of white wash on walls including cornices, pilasters etc, complete all as specified and directed.

Complete removal of existing treatement and applying two coats of white wash on wall, complete all as specified and directed.

All as per item No-93 above but on ceiling, complete all as specified and directed.

All as per item No-93 above but applying one coat of colour wash on walls complete all as specified and directed.

All as per item No-93 above but applying one coat of oil bound distemper white or any tint complete all as specified and directed.

Complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or tinted, complete all as specified and directed.

All as per item No-93 above but applying one coat of cement base paint on wall and AC sheet roof surfaces, complete all as specified and directed.

Complete removal of existing treatement from wall plaster and applying two coats of cement base paint, complete all as specified and directed.

M&L for Preparation of old painted steel surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern/single shade, complete all as specified and directed.

M&L for Preparation of old painted wooden or wood based surfaces of any description not otherwise described, over 10cm width or girth including knotting and stopping as required and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for Applying wall putty of approved make not less than 1mm thick on walls as per manufacturar instructions with and including rubbing by means of sand paper to have smooth finishing to receive primer / paint, complete all as specified and directed.

Writing letters or figures (Block, Roman, Italic or Indian) n. exc 30cm high with synthetic enamel paint including oblitering old writing of any description to match existing work, complete all as specified and directed.

Supply only liquid water proofing admixture complete all as specified and directed.

M/S Jyoti Parkash Tilak Raj Gupta

M/S Farooq Ahmed Bhat