WBPWD/PW(R)/SEPD/PIU-I/NIT-10 OF 2026-2027_SL_1

Construction of Embankment with Material Deposited from Roadway Cutting Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2 & 300-1.The size course material in the mix of earth ordinarily shall not be exceed 75mm.(Reference to MoRT&H's specification clause 305). Note In case the earth cutting is done by dozer and pushed for filling in the embankment, the input of dozer in the cost of embankment i.e. ₹ 39.63/m3 (excluding overhead, Contractor profit & L.W. cess) shall be deducted from theEstimated Rate as the same is already provided in the cost of excavation. However, if the earth is dumped by tippers from roadway cutting, the input of dozer for spreading is required to be provided.

Construction of Embankment with Material obtained from Borrow pits Construction of embankment with approved material obtained from borrow pits (Govt. land) with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 & 300-1 .The size course material in the mix of earth ordinarily shall not be exceed 75mm.(Reference to MoRT&H's specification clause 305). Cost of compensation for Earth material & its carriage from private land at 5km distance have been included in the rate.

Construction of Embankment with Material obtained from Borrow pits Construction of embankment with approved material obtained from borrow pits (land owned/arranged by the Agency with Royalty) with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 & 300-1 .The size course material in the mix of earth ordinarily shall not be exceed 75mm.(Reference to MoRT&H's specification clause 305). Cost of compensation for Earth material & its carriage from private land at 5km distance have been included in the rate. [Note: Royalty as appicable will be deducted from Agency's bill if not produce Royalty clearance certificate from the competent authority.]

Picking up and removing old bituminous layer or sand sealing coat from old black topped surface and leaning the exposed surface by scraping and stacking the material as directed. By mechanical means (without milling machine). Above 100 mm thick

Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density . The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. Using Rampurhat/Panchami variety stone material. (Payment will be made on the basis of finished compacted volume)

Dense Graded Bituminous Macadam Providing and laying dense graded bituminous macadam with 100-120 TPH batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder of approved grade @ 4.0% (min) for Grading -1 and 4.5% (min) for Grading -2 by weight of total mix and filler(Cement /hydrated lime / Rock dust ) as per table 500-10 and mix design done as per table 500- 11and job mix formula as per clause 505.3.3 transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem roller and with pneumatic tyre roller of 12 to 15 tonne weight with a pressure at least 0.56 MPa as directed by E-I-C, and to achieve the desired compaction as per MORT&H specification clause No. 505.3.5 complete in all respects (Reference to MORT&H's specification clause 505). For Grading 1 (37.5 mm nominal maximum aggregate size ) Layer Thickness 75-100mm Using Rampurhat/Panchami variety stone material, hydrated lime and bituminous binder (VG-40 bulk @ 104.00kg./ m3) Using Batch Type HMP of minimum capacity 100-120 TPH. (Payment will be made on the basis of finished compacted volume)

Dense Graded Bituminous Macadam Providing and laying dense graded bituminous macadam with 100-120 TPH batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder of approved grade @ 4.0% (min) for Grading -1 and 4.5% (min) for Grading -2 by weight of total mix and filler(Cement /hydrated lime / Rock dust ) as per table 500-10 and mix design done as per table 500- 11and job mix formula as per clause 505.3.3 transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem roller and with pneumatic tyre roller of 12 to 15 tonne weight with a pressure at least 0.56 MPa as directed by E-I-C, and to achieve the desired compaction as per MORT&H specification clause No. 505.3.5 complete in all respects (Reference to MORT&H's specification clause 505). For Grading 2 (26.5 mm nominal maximum aggregate size ) Layer Thickness 50-75mm Using Rampurhat/Panchami variety stone material, hydrated lime and bituminous binder (VG-40 bulk @ 104.00kg./ m3) Using Batch Type HMP of minimum capacity 100-120 TPH. (Payment will be made on the basis of finished compacted volume)

Bituminous Concrete Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder of approved grade@ 5.2% (min) for Gr.-1 & @ 5.4% (min) for Gr.-2 , as per table 500-17, and mix design done as per table 500-10 and job mix formula as per cl. 505.3.3 and filler(Cement /hydrated lime / Rock dust ), transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory tandem roller and with pneumatic tyre roller of 12 to 15 tonne weight with a pressure at least 0.56 MPa as directed by E-I-C to achieve the desired compaction as per clause no 507.3.5 complete in all respects ref. to MORTH specification clause No.507. For Grading 2 ( 13.2 mm nominal maximum aggregate size), Layer thickness: 30 mm compacted thick Using Rampurhat/Panchami variety stone material, hydrated lime and bituminous binder (VG-40 bulk @ 127.0kg./ m3) Using Batch Type HMP of minimum capacity 100-120 TPH. (Payment will be made on the basis of finished compacted volume)

Prime Coat Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer using mechanical means (Reference to MORT&H's specification clause 502). For WBM / WMM Surface: [with Cationic Bitumen Emulsion (Bulk) SS-1 Type @ 0.85 kg/ sqm] (Payment will be made on the basis of finished surface area)