8142/E8 REPAIRS/ MAINT OF EXTERNAL WATER SUPPLY, PUMP SETS, CLEANING OF OH TANKS, UG SUMPS OTHER CONNECTED WORKS AT DAD, REPAIRS TO LOW TENSION EXTERNAL ELECTRIC SUPPLY, STREET LIGHTS AND ALLIED WORKS AT DAD AND REPAIR/ MAINT OF INTERNAL ELECTRIC

Amount

Excavation in trenches n.exc 1.5 mtr wide and n exc 1.5 mtr in depth and getting out in soft/ loose soil for laying cables / GI pipe, foundation of pole, stay etc complete all as specified and as directed.

Returning, filling in using excavated soil including spreading, levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and as directed.

Removing surplus excavated soil n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and as directed.

Taking up or down steel tubing and connections including fittings of following bores in any length complete from trenches / walls / floor / roofs etc. all as specified and directed.

(a) 80 mm bore.

(b) 40/50mm bore.

(c) 20/25 mm bore.

(d) 15mm bore.

Supply and laying and testing GI tubing of following sizes bore galvanized medium grade of any length including all fittings such as bend, elbow, tee and union laid in trenches or on floors/ walls/ceilings etc. and connections complete all as specified and directed.

(a) 15 mm bore

(b) 20 mm bore

(c) 25 mm bore

(d) 40 mm bore

(e) 50 mm bore

(f) 80 mm bore

S&F in repair of unserviceable gun metal globe or gate valve of brass heavy duty ISI marked with iron wheel head, butterfly handle screwed both ends for iron pipe of following sizes bore including taking out old one complete in place of all as directed fixed in wall and ground.

(a) 15 mm bore

(b) 20 mm bore

(c ) 25 mm bore

(d) 40 mm bore

(e) 50 mm bore

S&F in repair of unserviceable cast iron sluice valve IS 14846 -200 PN1.6 both flanged heavy duty drilled and installed with brass spindle gun metal face rings rubber gasket 3mm thick MS bolts nuts and washers graphite rope complete including taking down the old unserviceable valves for following sizes bore.

(a) 80mm bore

M & L for Cutting the existing bituminous road / cement concrete surface 150 mm thick to the required width and depth for laying pipe line and making good the disturbed area to match with existing complete all as specified.

Demolition of the existing unserviceable valve chamber, M & L for construction of brick masonry (230 mm thick wall) valve pipe of size 600 x 600 x600mm inner dimension including necessary earth work , PCC 1:4 8, 75 mm thick Type D-2 using 40 mm graded stone aggregate as in foundation , brick wall build in CM 1:6, rendering 15 mm thick with CM 1: 6 externally upto 15 CM below GL and CM 1:4 internally and providing angle Iron base frame and MS Sheet cover 3.15 mm thick welded with hinges including necessary locking arrangement with handle, in and including dismantling & taking down old unserviceable broken Covers Complete. all as specified and directed.

Supply and fix Gland rope to sluice valve 80mm to 150mm , pumps (graphite rope ) (size 1/2",1/4",3/4") including taking out old unserviceable all as directed.

Supply and Fix MCCB 3 pole 25 to 100 Amps with breaking capacity 16 kA, 415 Volts, 50 Hz AC as per the site Requirement including taking down of old unserviceable all as directed.

Supply and Fix MCCB 4 pole 63 Amps with breaking capacity 16 KA, 415 Volts, 50 Hz AC as per the site Requirement including taking down of old unserviceable all as directed.

Developing / flushing of bore wells for a period of 6 hours using compressed air method upto availability of crystal clear water including removing and fixing the installation in original location all as specified and directed.

Dismantling the defective mono block or Jet pump set of capacity 5 HP from foundation by opening of coupling and foundation bolts and transporting to workshop for repairing and reassembling after servicing and overhauling complete with oiling/greasing, lubricating the parts including repair / replacement of worn out parts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint and installation commissioning and testing on full load complete all as specified and directed Note:- (i) The rate quoted for this item shall includes labour charge only for maint repair and replacement of defective/UNSV spares/accessories. Spares are to measured and paid separately under subsequent items. (ii) Cost of other minor items/spares such as nut, bolts washers, gaskets, paints etc which are not covered under Sch 'A' but required for effective functioning of the plant shall be deemed to included in this item.

All as per Item No. 14 above but for capacity 7.5 HP three phase monoblock pump set

Supply only the following items /parts for 5 HP mono block pump sets

(a) CI Impeller

(b) Ball bearing

(c) motor coupling assembly with tyre

Supply only the following items /parts for 7.5 HP mono block pump set

(a) CI Impeller

(b) Ball bearing

(c) Motor coupling assembly with tyre

Dismantling the motor of monoblock pump set of capacity 5.0 HP removing the existing burnt out winding and rewinding with copper winding wire of existing gauge and weight including replacement of all insulation material and terminal lead for AC single phase 230 volts grade and other petty items required for making motor functional and motor reassembling and shifting back to pump house and testing complete all as directed.

All as per Item No.18 above but for capacity 7.5 HP three phase monoblock pump set.

Taking out defective submersible pump set of capacity upto 3 HP from bore well for repair by lifting GI tubing of size 50 mm from up to 220 feet depth after disconnecting electrical and pipe line connection, complete by means of chain pulley block or other T&P, transporting to workshop including repair/replacement of worn out parts, servicing and overhauling complete with oiling/greasing, lubricating the parts and reassembling and painting of submersible pump set with motor with one coat of synthetic enamel paint after clearing and scrubbing and shifting back to bore well, lowering commissioning and testing on full load complete all as specified and directed.

Supply only following items / parts for 3HP submersible bore well pump set:-

(a) Thrust bearing complete

(b) Gun metal bearing bush.

(c) Stainless steel studs and nuts

(d) Bowl assembly

(f) Oil seal body

Dismantling the motor of submersible (vertical type) pump set of capacity 3 HP, removing the existing burnt out winding and rewinding with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and filling of cooling oil with oil seal and terminal lead for AC, 3 Phase, 415 volts grade and other petty items required for making motor functional and motor reassembling and testing complete all as directed.

S&F in repair of submersible PVC insulated cable of 650/1100 volts grade 3 core with flexible copper conductor water resistant quality ISI marked in replacement of following sizes:-

(a) 3 core 6sqmm

(b) 3 core 4sqmm

Cleaning the internal surfaces of Over Head Tank at any height / staging by scrapping down/brushing and removing all silt dirt, algae etc from walls, floors, washing/ cleaning with water and applying one coat of white wash to all internal surfaces of walls and ceilings and one coat of cement base paint to all external surfaces including top surfaces of OH tanks at any height and any position. All old steel surfaces such as vent pipes, inlet, outlet pipes, ladder shall be provided with one coat of anti corrosive bituminous paint and old MS pipe railing shall be scrapped properly and shall be painted with one coat of synthetic enamel paint. Paintings to oblitering labels shall be not less than 60x40cm using black paint same as existing dimensions and writing particulars etc using white paint with height of letters same as existing writing complete all as directed for 50000 gallons capacity Note: proper safety measure must take while painting.

Preparing the old steel / MS tubing and CI painted surfaces of pipe line with one coat of synthetic enamel paint black colour to existing suction pumping line near the pump house sump to pump house from pump to delivery line through raising and delivery main of the Overhead tank of following sizes of pipe:

(a) DI /CI/GI Pipe 100 mm dia

(b) MS/CI/DI pipe 80 mm dia

(c) MS /CI/GI pipe 50 mm dia

(d) CI/GI pipe 25 mm dia

Cleaning the internal surfaces of Under Ground Sump by scrapping down/brushing and removing all silt dirt, algae etc from walls, floors, washing/ cleaning with water and applying one coat of white wash to all internal surfaces of walls and bottom of room. All old steel surfaces such as vent pipes, inlet, outlet pipes, ladder shall be painted with one coat of anti corrosive bituminous paint. one coat synthetic outdoor anti corrosive bituminous paint in outdoor surface at any height at any position. Paintings to oblitering labels shall be not less than 60 x 40 cm using black paint same as existing dimensions and writing particulars etc using white paint with height of letters same as existing writing complete as directed for 50000 gallons capacity.

Servicing of LT Panel Board of any size , cleaning of panel board internally and externally Tightening of all screws and bolts & nuts replacing of minor parts like screws, washers lugs etc checking of serviceability of all switch gears , insulating the live parts, including welding and painting all as specified and as directed.

Preparation of old painted by scraping / cleaning with wire brushes to remove the old painting from pump & motor installed at all pump house and painted with one coat of approved enamel paint all as directed .

Supply and fix direct on line starter three phase suitable upto 7.5 HP Pump set in sheet metal enclosure, 415V, including taking out old unserviceable all as directed.

Supply and fix single phase preventor 3 phase 415 volts including taking out old unserviceable all as directed all as directed

M & L for run lead joint fixed in repairs including provision of spun yarn etc for following size of CI pipe fitting complete all as directed.

(a) 80mm CI pipe

(b) 100 mm CI pipe

Cutting the existing GI steel tubing following sizes bore and screwing the cut ends (or length) screw on pipe to form connector in trenches , floors or on walls and ceiling for alterations or addition and rejointing including connecting up with GI union , nipple and necessary GI fittings complete Note: Excavation will be measured and paid separately.

(a) 15mm bore

(a) 20mm bore

(a) 25mm bore

All as per item No.32 above but for 40/50mm bore pipe

Cutting the existing GI steel tubing 80mm bore and screwing the cut ends (or length) screw on pipe to form connector in trenches , floors or on walls and ceiling for alterations or addition and rejointing including connecting up with GI Flange complete Note: Excavation will be measured and paid separately

Demolition of Cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed .

M & L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and similar bands, plinth courses, string courses, lacing course, parapet, copings, kneelers, apex stones including necessary form work complete all as specified and directed.

Supply, lay / spread in trenches, sieving sand including cleaning, spreading, levelling, punning for laying /cushioning of cable all as specified and as directed. Note: Punned thickness shall be measured and paid.

Supplying and laying of reinforced precast concrete cable cover, class LV, Type 1, flat, size 250 mm x 150mm x 40mm complete including removing old bricks from cable cover trenches and taken as schedule of credit.

M&L for cutting the existing bituminous road / cement concrete surface 150mm thick to the required width and depth for laying pipe lines and making good the disturbed area to match with Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate to match with existing complete all as specified.

Disconnecting and taking out the old unserviceable LT UG cable in trenches, wall & poles and taken as credit including supply and Laying in trenches / poles / wall etc LT UG Cable XLPE insulated, armoured, heavy duty with multistranded aluminium conductor, 1100 volts grade conforming to IS specifications and of the following sizes:- Note: Lugs and glands are deemed to be included in the rate quoted for laying of cable and to be used wherever required while connecting cables to the panel board. Earth work such as excavation, refilling etc, shall be measured and paid separately under relevant item:-

(a) LT UG cable 2 core 10 sqmm

(b) LT UG cable 4 core 16sqmm

(c) LT UG cable 4 core 25sqmm

Re- laying only ( where directed at site) in trenches and connecting with suitable size of cable jointing kit/lugs/ thimble etc. serviceable under ground cable retrieved from taking out as Srl No - 40 of above schedule of following sizes:- Note:- Cable jointing kit will be measured & paid separately under relevant items of Sch 'A'.

(a) LT UG cable 4 core 16 sqmm

(b) LT UG cable 4 core 25 sqmm

S&F Straight through joints (epoxy) heat shrink type for underground cable including joint kits and labour complete for making joints suitable for LT PVC sheathed / armoured heavy duty cables with aluminium conductor of following sizes :-

(a) LT UG cable upto 4 core 16 sqmm

(b) LT UG cable 3.5/4 core 25 sqmm to 35 sqmm

Supply and lay in repairs steel tubes, 'light grade' galvanised, with all fittings; of bore of tube 40 mm laid in trenches for drawing cables under road/drain crossings etc all as specified and directed

Taking down the old unserviceable junction box and taken as credit including S&F Junction box PVC (FRP) Junction Boxes weather proof type with hinged type door off white colour of size 240x130x110mm with three pole connector and 1 No neutral link complete fixed on pole with suitable clamps, bolts and nuts with fixing arrangements all as specified and directed.

M&L for removing the existing street light fitting of any type & make and Supply & installation of new street light fittings,60W LED 5700K New generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 roadway luminaries with high power LED as light source in the existing pole duly wired complete all as specified and directed Make:- Havells , Cat part No. ENDURAPEARLNEOSL60WLED757PASYTOPCAST / Crompton cat part No. LSTP-60-CDL-M/ Wipro skyline LED cat No. LR02-671-XXX-57-XX./Bajaj cat No.ENXT P 60L WW CR PC SD.

Supply and laying 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape and overall PVC sheathed 3 core 2.5 sq. mm nominal cross section in service connections/street light connection from junction box to street light fittings.

S & F MCCB 3 pole 125 Amps,415 volts with rupturing capacity 16KA, all as specified including taking out old one

S & F MCCB 3 pole 63 Amps, 415 volts with rupturing capacity 16KA, all as specified including taking out old one

M & L for Earthing complete with galvanised steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried directly in ground vertically to a depth of not less than 2.25 mtr below normal ground level with top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanised iron/steel earth wire 4 mm dia by means of bolts, nuts, washers and check nuts made out of galvanised iron, protected by GI pipe light grade 15 mm bore dia and connected to main control board all as shown in Electrical plate No 3 of MES SSR Part I including necessary excavation and earth work in any type of soil, salt, charcoal dust, PCC 1:2:4 type B1 in chamber, RCC 1:2:4 chamber cover with 6 mm dia MS bar at 100 mm centre to centre both ways and MS 6 mm dia hook complete all as specified and directed.

Preparation of old surface and painting of steel tubular electric poles above coping level including brackets, clamps etc with good quality silver paint two coats complete including writing pole no and all as specified and directed.

Taking down carefully copper/ Aluminium point wiring (light, fan, socket or power) complete (fitting such as switches, ceiling roses, pendants, regulators, sockets, etc can be measured separately) removing the material from wall/ceiling etc, making good the disturbed surfaces and taken as credit.

M & L for Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable FRLS 1100 volts grade, multistranded with copper conductors conforming to IS specifications, with colour code drawn through and including non metallic casing capping, casing capping incl accessories fixed on wall / ceiling etc with suitable clamps, screws, etc in wall including making good the disturbed surfaces, matching with the existing wall surfaces including Provn of 1.5 sqmm PVC insulated FRLS unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly all as specified and as directed :-

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch and one regulator.

(c) One 3 pin 5 Amps switch socket on independent board.

(d) One 3 pine 5 amps switch socket on same board along with other switches.

(e) One bell point controlled by bell push switch on independent board.

M & L for Wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable FRLS 1100 volts grade, multistranded with copper conductors conforming to IS specifications, with colour code drawn through and including non metallic rigid PVC conduit, PVC conduit fittings and conduit accessories concealed on wall and fixed on ceiling etc with suitable clamps, screws, etc or concealed in wall including cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 for concealed conduit wiring and making good the disturbed surfaces, matching with the existing wall surfaces, cutting not exceeding 10 Cm girth ,including Provn of 1.5 sqmm PVC insulated FRLS unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly all as specified and as directed :-

(a) One light point controlled by one switch

(b) One fan point controlled by one switch and one regulator

(c) One 3 pin 5 Amps switch socket on independent board

(d) One 3 pine 5 amps switch socket on same board along with other switches.

(e) One bell point controlled by bell push switch on independent board.

All as per item No 52 herein before but with 4 Sqmm single core PVC cable for one 3 pin 15 amps switch socket outlet on independent board.

M & L for sub main wiring with PVC insulated, FRLS 1100 volts grade single core multistranded copper conductor cable conforming to IS specifications, 2 runs of 6 sqmm including one run of 6 sqmm single core multistranded copper conductor PVC insulated cables as earth continuity conductor with colour code drawn through and including one run of 25 mm dia rigid PVC conduit and conduit accessories or casing capping incl accessories fixed on wall/ceiling etc., or concealed in wall and connecting to common earth dolly including taking down old unsv all as specified and directed.

All as per item No 55 herein above but with 2 runs of 2.5 Sqmm and one run of 2.5 sqmm earth wire in PVC conduit as specified and as directed.

All as per item No 55 herein above but with 2 runs of 4 Sqmm and one run of 4 sqmm earth wire in PVC conduit as specified and as directed.

All as per item No 55 herein above but with 2 runs of 10 Sqmm and one run of 10 sqmm earth wire in PVC conduit as specified and as directed.

All as per item No 55 herein above but with 4runs of 10 sqmm and one run of 10 sq.mm earth wire in PVC conduit as specified and as directed. Note for item Nos 52 to 59 :- (a) The wiring shall be done in proper colour coding using red, yellow and blue for phase, black for neutral and green for earth leads. (b) For concealed wiring the quoted rate shall be inclusive wherever required cutting chases etc.

Taking down carefully by unscrewing from boards/outlet boxes, wall ceiling fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, with plug, switch fuse and regulators etc., taken as credit and making good the disturbed surfaces of wall etc all as directed.

S&F Ceiling rose surface Ceiling rose, 3 phase/PVC/polycarbonate, isolated body.

Supply and Fix Switch piano flush type 5 amps single pole, one way, 240 Volts all as directed.

Supply and Fix Switch socket combination 2 in 1, 3 pin, 5 amp, flush type all as directed.

Supply and Fix Socket outlet 3 pin 5 Amps flush type all as directed.

Supply and Fix Bell push flush type 5 amps single pole 240 Volts all as directed.

Supply and Fix Buzzer, AC, 230 volts, single pole all as directed.

Supply and Fix Bell ding dong, AC, 230 volts, single pole all as directed.

Supply and Fix Socket outlet 3 pin 15 amps flush type all as directed.

Supply and Fix Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp multipurpose controlled by one switch all as directed.

Supply and Fix Switch socket outlet modular type multipurpose 3 pin, 15/16 amp and one pin, 5 amp controlled by one switch all as directed.

S & F stepped type electronic fan regulator flush type all as directed.

S & F Lamp holder PVC/polycarbonate with back plate for pendant/batten fittings all as directed.

S & F modular Fan step regulator, 120W - 1 module for ceiling Fan of 1200 mm sweep all as specified and as directed.

Supply and Fix modular switch 1 way 6A, 1 module

Supply and Fix modular switch 1 way 16A, 1 module

Supply and Fix modular Bell push 6A 1 module

Supply & Fix Bell Multimusical type all as specified and as directed.

S&F Modular white cover with plate with frame 2 module incl matching with white cement wk if necessary

S&F Modular white cover with plate with frame 3 module incl matching with white cement wk if necessary

S&F Modular white cover with plate with frame 4 module incl matching with white cement wk if necessary

S&F Modular white cover with plate with frame 6 module incl matching with white cement wk if necessary

S&F Modular white cover with plate with frame 8 module incl matching with white cement wk if necessary

Supply and Modular flush box 1/2 module

Supply and Modular flush box 3 module

Supply and Modular flush box 4 module

Supply and Modular flush box 6 module

Supply and replacement of metal clad socket single pole and neutral enclosure with a two pin and earth plug top and socket complete with one single pole MCB 230 Volts 20/32 Amps all as specified and as directed.

Taking down carefully existing un-serviceable main switch, DB's including boards etc, from its original position complete all as directed.

Supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated bus bar with neutral link, 4 ways SPN Double door, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed.

Supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated bus bar with neutral link, 8 ways SPN Double door, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed.

Supply and fix MCB Distribution board , 240 volts single pole and neutral ,double door, sheet steel, enclosure powder coated with 200 Amps rated bus bar with neutral link, 12 ways SPN Double door, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed.

Supply and fix MCB DP, 240 Volts, 20-63 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed including taking down old one.

Supply and fix MCB SP, 240 Volt,10-32 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed including taking down old one.

S & F RCBO single pole & neutral, 240 volts, 40 amps, 30mA, 10kA all as directed.

Dismantling the following types of fans of any make/model/sweep, removing the burnt out winding wires, rewinding with winding wires and insulation materials overhauling/servicing, greasing/lubricating, insulating electric leads, replacing cotter pins, bolts nuts, replacing unserviceable bearing, bushes assembling back checking for proper fixing and safety and testing all as directed and specified for :-

(a) ceiling fan upto 1400 mm sweep.

(b) Exhaust fan upto 450 mm sweep.

Removing following unserviceable parts/items, supply and fix new items/parts of same specification existing and as described below for ceiling/exhaust/pedestal fans etc

(a) Ball bearing for ceiling fan/Exhaust fan/Wall fan/Pedestal fan upto 1400mm sweep.

(b) Bush bearing for ceiling fan/Exhaust fan/Wall fan/Pedestal fan upto 1400mm sweep.

(c) Fan condenser capacitor 2.5 mfd.

(d) Fan condenser capacitor 4 mfd.

(e) Fan clamp for ceiling fan complete with rubber shackle, shackle bolt, nut, cotter pin, clamp complete.

Taking down and refixing incl painting of water heaters (Geysers) of following capacity of any make/model in site with synthetic enamel paint by brush including filling of cavities with fillers one coat after cleaning all dust etc including writing MES numbers etc all as specified and directed for :

(a) Water heater 25 litres capacity.

Dismantling following unserviceable items/parts from water heaters of any capacity/make/model, supply and fix new items/parts of same capacity/type/model, connecting up and testing :-

(a) Heating element 1.5 KW capacity AC 230 V and conforming to IS specifications screw/flange type.

(b) Heating element 2.0 KW capacity AC 230 V and conforming to IS specifications screw/flange type.

(c) Thermostat suitable for water heater upto 50 litres capacity.

(d) Indicator lamp any type suitable for water heaters upto 50 litres capacity.

(e) Non return valve 15 mm dia size.

(f) PVC connections with brass check nuts 15 mm dia x 45 cm long for hot water supply.

(g) PVC connections with brass check nuts 15 mm dia x 45 cm long for cold water supply.

(h) Rubber gasket flat/'O' ring type suitable for water heater

(j) PVC cable 3 core flexible copper conductor cable of size 40/0.193

(k) Plug top 3 pin 15 amps.

(l) Pressure release Valve suitable for geysers upto 25 litres capacity.

Supply and fix in repair of retrofit lamp 11 watt E-27/B22 type suitable for 230 Volts 50 Hz AC supply complete including taking out old/unserviceable complete as directed

Supply and fix Wall mounted LED Batten with tube extruded Aluminium heat shrink provided for efficient heat dissipation & integrated electronic driver of Lamp type: 20W LED life time of 30000* hours including lamp all as specified and as directed. Make:Havells cat part No. LUMILINEPLUSBS20WLED865SPCSS/ CROMPTON cat part No.TRIMLINE LDL-20-WW/ Bajaj cat part No-BCLSB 20 WH

Supply and fixing LED lights fitting 1x 22 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. Make:- havells cat No.ENDURA LINEAR NEO BS22 WLED 865 SPCWH/ PHILIPS cat No B1021LED25S6500PSUGRST/ CROMPTON cat No. LDRR24-CDL/ BAJAJ Cat No. BCLAB SP 22L LEDCWPCSD.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make:- havells cat No.ENDURA LINEAR NEO BS10WLED 865SPC WH / BAJAJ Cat No. BCLAB SP 10WH/ CRMPTON Cat No. LDLL 10- CDL.

Dismantling existing UNSV hylam sheet of any size from boards removing switches etc. Supply and fix hylam sheet 3mm thick including necessary cutting of suitable opening for switches, sockets, regulators, etc refixing of switches, sockets, regulators, etc replacing screws and connecting up and testing.

Supply and fixing round shape 10/12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete three core flexible copper conductor cable of suitable size complete. Make:- Havells cat No. INTEGRA NEO SURFACED LS10WLED 840S/ CROMPTON cat No. LCDSPLN-R-12-CDL/ BAJAJ Cat No. BGSLO SLEEK SURFACE 12WWH RD.

S & F LED light fitting 1x9W/1X10W bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. Make:- Havells cat No.HEXAFT10WLED 857SSYMBOPC/ PHILIPS Cat No. WT202W LED10S CW PSU S3 PC /BAJAJ Cat No. BIBWP 10W LED.

Supply & Fixing of LED driver for LED fittings upto 40Watts of Any size/type .

S & F in replacement decorative wall light, stainless steel rust free fixture with white glass diffuser prewired, suitable for 9w LED filament lamp E27 base including LED lamp complete. Make : Havells cat No. FLORETINE WL 1LS E27 SS/Philips cat No. 31425 20-watt/

Removing old building security lights, supply and fixing energy saving LED security light fitting 30W made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP66 protection complete all as specified and directed. Make:- Havells cat No- ENDURA PEARL SL30W LED 757SASY TOPCMP/ HALONIX cat no HLSLD-09-30CWL-R/ CROPTON cat no. LSTS-30-CDL/NL-M/ Wipro cat No.LR02-331-XXX-57-XX 30Watt.