SPL REPAIR TO OR MD ACCN BLDG NO P-116 (1 TO 8) AT RH LINE OF ARMD DIV SIG REGT (AREN) UNDER GE JHANSI

Demolition of cement concrete incl terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar, complete all as specified and directed.

M&L for 75 mm thick cement concrete type D2 1:4:8 (using 40 mm graded stone agg) in sub base of flooring/ hard standing complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

M&L for Non skid ceramic colored tiles , 7 to 8 mm thick (square / rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm as in flooring etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed.

M&L for ceramic colour tiles in vertical surface of size 350 X 250 x 7/450x300x7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and as directed.

M&L for Non-skid colour ceramic tile tiles joint free 8 to 10 mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry over 15 mm thick screed bed or bedding layer in CM 1:6 over brushing neat cement slurry etc complete all as speciefied and directed.

All as per item here-in-above but on vertical surfaces such as skirting/dado over and including 10mm thick CM rendering (backing coat) in CM 1:4,complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness laid , bedded and pointed in any mortar as in floors, aprons etc. complete all as specified and directed.

M&L for factory made machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 50mm thick sand cushioning, including in CM (1:3) in edges of pavers, complete all as specified and directed. (Note : The cost of sand cushion and plastering to edges is included in quoted rate.)

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L for machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 10 mm thick backing coat in CM 1:4 complete all as specified and directed. Note: Kota stone in Step will be placed in single piece with groove lines at edge.

M&L 20 mm thick granite slab of any type , tabled rubbed, machine cut, duly grinding, polishing, moulding etc of all outer edges / sharp corners, duly fixed in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4), incl pointing in grey cement (1:2) using marble dust with admixture of pigment to match with the shade of slab, complete all specified and directed.

M & L 18/19 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including dismantling of old boarding, cupborad any description, fixed in any position including fittings, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately)

M & L 25 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations, kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, including dismantling of old boarding, cupborad any description, fixed in any position including fittings , all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges shall be paid separately)

Providing and fixing 2mm thick 18 to 25 mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge.

S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 30mm, complete all as specified and directed

S & F drawer/shutter handles, projection drop (50mm to 65mm) on screwed platey complete all as specified and directed

S & F 100 mm aluminium anodise hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed

Supply & Fix stainless steel magnetic catcher fancy type for kitchen cabinet / drawer complete all as specified and directed by Engineer-in-Charge.

S&F in repair Rubber bush (door seal) of 25mm wide fixed to door complete all as specified and directed

Demolition of brick work built in cement mortar or lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with old size fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for half brick thick wall with old size fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed. Note: WPC in 5 mm thick 2nd layer plaster measured and paid separately.

M&L for 10 mm rendering thick in CM (1:6) on fair faces of brick work/concrete surfaces finished even & smooth (without using extra cement), complete all as specified and directed.

M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC ) on fair faces of brick work/concrete surfaces, finished even & smooth (without using extra cement), complete all as specified and directed. Notes: WPC in 5 mm thick 2nd layer plaster measured and paid separately.

M&L for preparation of new plastered of wall surface and applying two coats of oil bound distemper, over a coat of chalk whitening primer over and incl a layer 3mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

M&L for preparation of surfaces of walls and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as specified and directed. Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact.

M&L for preparation of newly plastered surfaces and applying two coats of white wash on ceiling all as specified and directed.

M&L for complete removal of existing treatment and preparation of surfaces of walls by scrapping/sand paper rubbing and finally washing with watering and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed. Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact.

M&L for complete removal of existing treatment and preparation of surfaces of walls by scrapping/sand paper rubbing and finally washing with watering preparation of old plastered surfaces and applying three coats of white wash on ceiling all as specified and directed.

M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated surfaces of wall and applying two coat of oil bound distemper over a coat of chalk whitening primer, over a layer of (JK/Birla) 3.0 mm thick wall care putty to get smooth and level finish, complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each including cutting holes in brick/ stone wall built in cement / lime mortar, embedded portion exc half brick but n.exc one brick for inserting new hold fast and making good the disturbed portion/surfaces, in CM 1:3 complete all as directed.

All as per item here-in-above but not exc 1.5 sqm each

Taking down shutters of any description not exc 01 Sqm each, complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm (± 5 mm tolerence in dimension) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners incl in this item of required dia and length complete as per direction of Engineer-in-Charge.

S & F for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified & directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick prelaminated colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made single 30 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F Factory made single 35 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

M&L 30mm thick factory made solid WPC (Wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including stainless steel wire shall mesh be fixed with 15x15 Square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fie again of the shall be as per manufacture instruction complete all as specified and complete all as specified and complete all as specified and directed.

S &F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm prelaminated colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

Supply and fixing of powder coated (Min thickness of powder coating 50 micron) anodised aluminium frame section of door, windows, ventilation, partion wall, cup board with one or more rebates including joinging cleats for fixing etc. complte all as specified.

Providing and fixing powder coated anodised aluminium window and ventilator shutters, hung/sliding type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading,screws, anodised aluminium fittingssuch as peg stays 150 mm long (1 No.) hinges type B-21 100 mm long (2 nos.) suitable handle (1 no.) etc all as specified and directed .

S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of gradeAC 15) of approved design/pattern, with approved standard sectionand fixed to the existing window frame with C.P. brass/ stainlesssteel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed

S&F of aluminium alloy anodized sliding door bolt 300mm (aldrop bolt) length with hasp staple and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all specified and directed

S&F of 100 mm size butt hinges, extruded aluminum alloy with galvanized mild steel pin type B-21 anodized complete all specified and directed

S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all specified and directed.

S&F of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed

S&F of 140 mm door stopper of aluminium body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed.

S & F in repair stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets, complete all as specified and directed.

S & F in repair stainless steel rod 15mm dia steel pipe cutting into length as required at site with and incl SS end brackets, fixed in cupboard and similar works, complete all as specified and directed.

S&F of ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of Ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors, including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC(SWR) vent cowl 110mm bore, jointing to waste pipe, complete all as specified and directed.

S&F PVC floor trap of 75 mm outlet, jointing to waste pipe, complete all as specified and directed.

M & L for PVC (SWR) gully trap 110 mm, setting and jointing with solvent cement complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

S & F 20 mm bore Galvanized Steel tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open incl cutting of grooves including taking up or down with connections and fittings all as specified and directed

M&L for cutting chases, pinning in for concealed water tubing, not exc 10 cm girth and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc complete all as specified and directed.

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with and incl disconnecting and dismantling the existing un-serviceable PVC/RCC water tank on top of roof/slab of bldgs, complete all as specified and directed.

S&F of 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F of 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed. (minium weight 20 mm-210 gms) etc, complete all as directed.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

S&F in replacement of stainless steel kitchen plate rack made out of 1 mm thick sheet of size 765x920mm and 220mm deep, weight not less than 7 Kg, complete all as specified and as directed.

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with long screwed shanks and fly-nuts, complete all specified and directed.

S&F in replacement of stop cock with long shank and cup (concealed type), 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe / unions, complete all as specified and directed.

S&F in replacement of overhead shower of dia 125 mm round shape single flow, ABS body chrome plated fancy type, with and incl swivel type shower arm of 20mm dia with wall flange made of cast copper alloy, chromium plated fancy type, complete all specified and directed.

S&F in replacement of long body bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all specified and directed.

S&F in replacement of angular stop cock 15 mm dia with wall flange made of cast copper alloy, chromium plated type, complete all specified and directed.

S&F in repair SS grating of squre/round shape, overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and incl fixing with CM to floor/nahani traps etc, complete all specified and directed.

S&F in replacement of towel rail 600 mm long D type between flange and wall bracket made of cast copper alloy, chromium plated, complete all specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as directed.

S&F in replacement of PVC multipurpose cabinet mirror with front openable door of overall size 350 x 450 mm, complete all as specified and directed.

S&F in replacement of Brass CP connection 15mm dia and 45cm long with 2 Nos brass check nuts with washers for geyser, complete all as directed.

S&F in replacement of PVC waste pipe 32 mm dia 750 mm long with for wash hand basin or for kitchen sink, complete all as specified and directed.

S&F in replacement of PVC connection 600 x 15mm dia PTMT (PVC), complete all as directed.

S&F in replacement of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white, with inlet ball valve, float and handle with and including wall bracket, 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet, including all joints and making good to the wall & floor,complete all specified and directed.

S&F in replacement of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe, P Trap and connecting cone but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface, complete all as directed.

S&F in replacement of 1st quality vitreous china wash hand basin, white flat/angle back, size 550x400mm, complete including necessary cutting for and pinning in ends of brackets) with and including wall brackets, PVC waste pipe of 750mm long, CP waste coupling of 32mm dia size, complete all as specified and directed.

S&F in replacement of corner glass shelf 300 mm with Chromium plated bracket guard and railing and fixing accessories, complete all as directed.

Demolition of RCC Not exc 15cm thickness Roofs, floors (other than ground floors), beams staircases, landing, chajjas, Cover slab and similar suspended work

M&L for RCC Type B1 1:1.5:3 (nominal mix) using 20 mm stone agg as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, chajja, canopies, deck slabs and in shelves and the like

M&L for mild steel deformed TMT bars 5 mm To 10mm dia and over (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as spd and directed by engr in charge

M & L for rough finish formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Supply only integral liquid water proofing compound LW++, mixed in CM as per manufacturer instruction, complete all as specified and directed.

Demolition of cement concrete of any description and in any position of WC’s/Bathroom etc in sunken portion area above ground floor, removing demolished material completely and old waste pipe from sunken portion and cleaning the side/bottom surface of sunken floor with wire brush, complete all as specified and directed.

M&L for application/forming of waterproofing liquid membrane moistening the prepared surface to toilet area of sunken floor for proper dispersion and penetration and applying two component cementitious elastomeric water proofing coating damp block 2k manufactured by M/s Asian Paints Ltd /Berger and Equivalent in two coats @ 1.4kg/Sqm to build 1mm thickness as per manufacturers specifications as follows . First coat shall be applied @ 0.7kg/Sqm and while Ist coat is still green the second coat shall be applied with a suitable and stiff brush @ 0.7 Kg/Sqm. The treatment shall be carried out to the entire bottom surface and vertical surface upto the bottom height of wall tiles. Adequate curing to be done on vertical surfaces and ponding test for 48 hours on the bottom surface to be carried out complete all as specified and directed by Engr-in-Charge. Make : M/s Asian Paints/Berger and Equivalent. Followed with water curing and testing for leak proof by ponding test for 48 Hours NOTE : (a) Treatment shall be done through authorised applicator/representative of the manufacturer only. (b) A 5years waterproofing warranty to be submitted by the both contractor and the manufacturer

M&L PCC 1:5:10 Type E2 using 40mm graded stone aggregate as in mass filling in two layer in sunken portion complete all as spd and directed

M&L for 50mm dia G.I pipe as in spout to drain out if any leakage occures in the sunken portion complete all as spd

Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m depth, for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 sqm on plan and n.exc 1.5 m in dedpth and getting out hard/dense soil complete all as specified and directed

M&L for Returning, filling in including spreading, levelling, watering and well ramming in layersnot exc 25 cm and getting in loose soil all as specified as directed.

M&L of removing excavated material nexc.50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as well as specified

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed.

M&L for point wiring for modular fittings complete with 1.5 Sqmm FRLSH insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm(OD), concealed in wall/ floor etc including provision of modular cover plates with frames and 1.50 sq mm PVC insulated unsheathed stranded copper conductor (FRLSH) cable for common earth and connecting to earth dolly all as specified and directed by Enrg-in-charge. (Note- rates of chasing/cutting & making goods shall be included in the unit rate) :-

One light point/ceiling fan/exhaust fan/call bell controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

Point

M&L for submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit ISI Marked conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc incl taking down old submain wiring alongwith conduit complete all as specified and directed by Engineer-in-Charge. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

Supply and fix of Modular switch 1 way 6A, 1 module 240V, 50Hz complete all as specied and directed.

Supply and fix of Modular fan regulator step type in 5 steps, 240V, 50Hz complete all as specified and directed.

Supply and fix of Modular Socket, 6A - 2/3 pin combined 2 module 240V, 50Hz complete all as specified and directed.

Supply and fix of Modular switch 1 way 16A, 1 module 240V, 50Hz complete all as specified and directed.

Supply and fix of Modular Socket 6A/16A - 2/3 pin combined 2 module 240V, 50Hz complete all as specified and directed.

S&F of Lamp holder, angle type with metal ring, PVC/Polycarbonate body complete all as specified and directed.

S&F of Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.

S&F Modular Bell Push , flush type, 5 Amp, marked with valid CML complete all as specified and directed

S&F electric bell of DINGDONG type, 240 volts, single pole, marked with valid CML and making all necessary connections, complete all as specified and directed.

S & F of 7W White LED retrofit lamp suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink.

Supply and fix in replacement of Decorative wall light fixture made up of Polycarbonate with and including 7W retrofit LED lamp, full white / warm white of approved model complete all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement of exhaust fan with plastic body with louvers, 250 mm sweep, single phase, 230 volts, 50 Hz. complete all as specified and directed.

Supply and fix in replacement of LED lights fitting 1 x 20 W 4 feet, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fix in replacement of LED light fitting 1 x 10 W bulkhead luminaires including LED Driver holder connecting up with three core flexible copper conductor cable of suitable size.

Supply and fix in replacement of LED building security light fitting 35 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP 65degree of protection including GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and as directed by Engineer-in-Charge.

Supply and fix of Electric Water Heater storage type, vertical, 25 Ltrs capacity, 5 Star rated, with heating element, PUF insulation, multifunction safety valve, adjustable knob for temperature setting and steel/PVC body with glass line/SS inner tank and outer body suitable for operating on 230V, 50 Hz, single phase AC supply including hot & cold water PVC connections and mounting on wall with suitable size & No. of anchor bolts complete all as specified and directed. Note. Old and u/s geyser removed from site and deposited to AGE E/M Yard . Make- Havells/Crompton/Bajaj

S&F of ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value more than 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed by Engineer-in-Charge. Note. Old and u/s ceiling fan removed from site and deposited to AGE E/M Yard . Make- Havells/Crompton/Bajaj

Supply and fix in replacement of modular MCB protected plug and socket board in sheet steel enclosure with 25A rated mini MCB and 25A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed by Engineer-in-Charge.

S&F in replacement of MCB distribution board, TPN, 4 way, 415 V, 3 phase, AC in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface complete all as specified and directed. Note: MCBs shall be measured and paid separately.

畓灰祬愠摮映硩椠敲汰捡浥湥⁴景䴠䉃搠獩牴扩瑵潩潢牡Ɽ匠乐‬‸慷⁹㌲‰潖瑬椠桳敥⁴瑳敥潰摷牥瀠楡瑮摥攠据潬畳敲搠畯汢⁥潤牯琠灹⁥楷桴†偉㐠″敤牧敥漠⁦牰瑯捥楴湯眠瑩⁨畢汩⁴湩挠灯数⁲畢⁳慢Ⱳ渠略牴污氠湩湡⁤慥瑲⁨楬歮挠浯汰瑥⁥湩汣摵湩⁧畣瑴湩⁧桴⁥慷汬猠牵慦散⁳潦⁲汦獵⁨潭湵楴杮漠⁦䉄愠摮洠歡湩⁧潧摯眠瑩⁨散敭瑮瀠慬瑳牥‬異瑴⁹湡⁤慰湩⁴潴洠瑡档眠瑩⁨桴⁥硥獩楴杮猠牵慦散愠汬愠⁳灳捥晩敩⁤湡⁤楤敲瑣摥戠⁹湅楧敮牥椭⵮桃牡敧‮丠瑯㩥†䍍獂猠慨汬戠⁥敭獡牵摥愠摮瀠楡⁤敳慰敲整祬‮†Ǫ匀灵汰⁹湡⁤楦⁸湩爠灥慬散敭瑮漠⁦䍍⁂楤瑳楲畢楴湯戠慯摲‬偓ⱎ㐠眠祡㈠〳嘠汯⁴湩猠敨瑥猠整汥瀠睯敤⁲慰湩整⁤湥汣獯牵⁥潤扵敬搠潯⁲祴数眠瑩⁨䤠⁐㌴搠来敲⁥景瀠潲整瑣潩楷桴戠極瑬椠潣灰牥戠獵戠牡‬敮瑵慲楬歮愠摮攠牡桴氠湩潣灭敬整椠据畬楤杮挠瑵楴杮琠敨眠污畳晲捡獥映牯映畬桳洠畯瑮湩⁧景䐠⁂湡⁤慭楫杮朠潯⁤楷桴挠浥湥⁴汰獡整Ⱳ瀠瑵祴愠摮瀠楡瑮琠慭捴⁨楷桴琠敨攠楸瑳湩⁧

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for laying of GI Pipe and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed by Engineer-in-Charge.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge.