SPECIAL REPAIRS TO BUILDING NS-107 OFFICERS MESS NAVAL PARK AT MO MB GHATKOPAR UNDER GE NW BHANDUP

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises etc outside MD land complete all as specified and directed.

Demolition of brick work or stone boulder masonry,built in cement mortar or cement lime mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work and precast concrete articles and removal of rubbish/ demolished materials out of MD land complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or stone wall and ceiling surface including raking out joints, hacking for key, scrubbing down with water etc and disposing off the rubbish outside MD land complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frames) and including grills/ guard bars not exceeding 1.5 Sqm each complete as directed

M&L for Non-skid ceramic tiles (Coloured) 7 to 8mm thick rectangular area of each tiles exc 0.18 sqm and n exc 0.38 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thick screed bed in CM 1:6 laying floor finished complete all as specified and directed.

M&L for Non-skid ceramic tiles (Coloured) 7 to 8mm thick rectangular area of each tiles exc 0.06 sqm n exc 0.11 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 laying floor finished complete all as specified and directed.

M&L for vertified ceramic tiles 10mm (light shade of square/ rectangular) polished, area of each tiles not exc 0.36 sqm in floors etc,.set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 laying floor finishesed complete all as specified and directed.

M&L for glazed ceramic coloured tiles 350x250x7mm / 450x350x7mm thick in vertical surfaces such as skirting/dado and jointed in neat cement slurry and pointed in white or coloured cement to match and including over 10mm thick rendering in CM 1:4 on fair faces of brick/concrete surfaces as in backing coat for tiles. etc, all as specified and directed.

M&L for brick work with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specifed and directed

M & L for rendering 10 mm thick in CM 1:6 on brick walls or concrete surfaces and finishing the surfaces even and fair complete all as specified and directed.

M & L for rendering 5 mm thick in CM 1:3 on concrete surfaces as in ceiling and finishing the surfaces even and smooth complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces in two coats (10 + 5 mm), second coat mixed with integral water proofing compound ISI Marked @ 2% by the weight of cement and finishing the surface even and fair complete all as specified and directed Note - WPC shall be measured and paid separately

Supply only integral water proofing compound. Complete all as specified and directed.

Material and labour for cracks with polymer based chemical Dr fixit cracks shrink free or equivalant for cracks not exc 10mm in width as per manufacturer instruction on wall surfaces on concrete or masonry incl scaffolding etc complete all as spd.

M&L for preparation of new plasterd surfaces of wall and applying two coats of Dr fixit rain coat over one coat of Dr fixit primer all as spd and directed by Engr-in-Charge

M&L for complete removal of existing treatment on walls including washing down, rubbing down and applying two coats of Dr fixit rain coat over one coat of Dr fixit primer all as specified and directed

M & L for preparation of new plastered surfaces of walls and applying Two coat of oil bound distemper including application of wall care putty (3mm thick) for smooth finish.etc with roller over one coat of alkali resistant primer including chalk whiting complete all as specified and directed.

M&L for preparation of old decorated surfaces of wall by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and thereafter applying with roller Two coat of oil bound distemper including application of wall care putty (3mm thick) and primer for smooth finish.etc complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of OBD incl one coat of chalk whiting primer. Complete all as specified and directed

M&L for preparation of old plastered surfaces of ceiling and applying one coat of OBD. Complete all as specified and directed

M&L for preparation of old wooden surfaces of any description, not other wise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Dismantling of roof terracing cement / brick concrete (un-reinforced) and existing water proofing treatment of any thickness in any position and of any portion from top of roof of building, cleaning surface of roof with wire brush / mechanical brush and with water thoroughly to remove all dust / dirt and loose particles to expose base concrete roof slab and removal of rubbish / demolished material out of MD land complete all as specified.

M&L for PCC 1:2:4 Type B0 using 12.5 mm graded aggregate with 2% by weight of cement or as per manufacturer's instructions water proofing as in levelling course, haunching, coping and similar works over RCC roof surface and RCC over head tank top surface including rounded or chamferred on edges and formwork etc all as specified and directed. Note : WPC to be messured and paid separately.

M&L for cleanning the surfaces with water and wire brush to remove dirt, dust, and other bio organism and repair the broken area with cement sand mortar and open major cracks with cement + thermacool WP 51 to make putty to fill the cracks.Once the surface is dry apply a liberal absorption coat of temacool WP 51 as follows, 1 Ltr thermacool WP 51 + 2 Ltr water mix well and apply by brush liberally . After the absorption coat dries apply first coat one Ltr Thermacool WP 51 + 250 ml of cement + 250 ml of water and floor joinery . Then apply on the entire area while recoating the joinery. Once the water proofing layer is dry, apply first coat of Thermacool 0.3 c followed by second coat of 0.3c upon drying.

S&F in replacement of 160mm bore PVC rain water pipe / vally guttersingle socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps 8mm dia with two nuts wall nails etc complete all as specifed and directed.

S&F in repair mangalore patern designable roof sheet for Pre- Painted aluminium zinc coating GI based steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering fixed with self tapping ,drilling of screws/suitable length GI 'J' or 'L' hooks in roof complete all as specified and directed.

S&F for roof trusses (framed) trussed, Purlins, crane gantries, rails and fastenings and heavy brackets framing(Beam, Angle, Channel or flat section,plain plates) including distance pieces, cleats ,welding and braceing etc,Fe-410W(Gde-E-250)quality -B, including necessary scaffolding etc complete all as specified and directed.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar / concrete to ensure bond between old concrete & new concrete/ new mortar by brush application, complete all as specified and directed.

M&L for carry out application of Bi -polar migratory corrosion inhibitor (make, M/S Krishna conchem (EPCO KP -100) / BASF ( master protect 8000 CI) on RCC exposed surfaces , complete all as spd and directed .( Note: Mode of measurment superficial area of concrete will be measured.)

M&L for Anticorrosive Treatment to Reinforcement using IPNET-RB of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces complete all as specified and directed . Note :- Mode of measurement: superficial area of concrete will be measured.

M&L for casting & repairing of excessively damaged distressedRCC members (exceeding 60mm in thikness) with prebatched, prepacked, single component ready to use microconcrete from Fosroc (Renderoc RG) or equivalent of Dr. Fixit as approved by GE, at any level/ height and at any lead or lift as directed including prefabricated water tight formwork, centering, scaffolding, also including mixing , laying, levelling, finishing, curing etc as per manufacturer's specifications and all other relevant works, complete all as specified and directed. (Note : Reinforcement only shall be measured and paid separately).

S&F in repair vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to pugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for ischarge pipe. (Exclusive offixing supply pipe to flushingcistern, trap and waste pipe)

M&L for 20mm thick granite(of any type) work table rubbed and polished as in flooring, steps, jambs, pillars, windows-cill, cooking platform , and the like in cement mortar (1:4) including pointing in white / coloured cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting , moulding etc over and including 10mm thick rendering / screed bed in CM 1:4 on fair faces of brick/concrete surfaces complete all as specified and directed.

M&L PCC 1:4:8 C-2 (using 40mm graded crushed stone aggregate) as in sub base ( 75mm thick ) finished even and fair all as specified.

M&L for chequered cement concrete tiles 25cmX25cmX22mm thick,set jointed in neat cement slurry in floors with grey cement and pigments and including over 20mm thick screed bed in CM 1:4 etc and as approved by EIC

S&Fin repair wash down water closet (pedestal pattern) white and including plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device (excluding flushing cistern ) etc complete all as specified and directed..

S&F in repair CP corner glass with brass bracket screws etc complete all as specified and directed.

S&F in repairs counter wash hand basin, vitreous china white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed.

S&F in repairs colour wash hand basin, vitreous china white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed. make:jaquar, Marc, Kohler

Supply and fix in repair 10 ltr, PVC, valveless, syphonic action type, flushing cistern, low level/ high level including inlet, ball valve, float and handle including brackets with and including PVC flush pipe 32 mm bore, connecting to WC etc, complete all as specified and directed.

S&F PVC floor traps with grating complete 100mm bore outlet including jointing to waste pipe fixed in cement mortar type B1 1:2:4.

S&F CP concealed stop cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F in repairs CP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S/F in repairs brass Chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed 15mm bore fancy type.

S&F in repairs CP long nose bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed.

S&Fin repair 15mm size PVC connection with PTMT nuts 450mm length.complete all as specified and directed.

S&F in repair CP Tubular towel rail with hook 20 mm dia 600mm long between flanges of fixed with and including chromium plated brass screws and wooden/plastic screws. complete all as specified and directed.

S&F in repairs chromium plated shower roses 125mm size with or without swivel joint including fixing to steel pipe or union etc.complete all as specified and directed.

S&F Soap dish, Stainless steel fancy type approx size 160x160x90mm complete all as specified and directed.

S&F in repair Toilet paper holder cat No BA-58 of Prayag polymers pvt ltd complete all as specified and directed.

S&F in repair Health faucet with 1.5mtr tube & hook cat No BEA-40 of Prayag polymers pvt ltd complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm complete all as specified and directed.

Cutting and grooving of wall for fixing of UPVC pipe lines and after fixing of UPVC pipe line and making good of all cutting surfaces

S&F 15mm bore U- PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. with all fittings completed all as specifiec and directed.

S&F 20mm bore U- PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. with all fittings completed all as specifiec and directed.

S&F Solid PVC door frame (Chowkhat) of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube etc complete all as specified and directed.

S&F for Factory made solid PVC Moulded door shutter, 28 to 30 mm thick, with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing with wood free EPS complete all as specified and as directed.

S&F standard aluminum section powder coded in partition / frame and door shutter, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed (Aluminum section shall be of make Jindal / Hindalco / Indalco). Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

Supply only 4mm thick sheet figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane etc complete all as specified and directed

Supply only 4.80mm thick ordinary quality plain not exc 0.5 Sqm each pane with including wooden/rubber beading or gasket for aluminium section complete all as specified.

Supply only stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed.

S&F aluminum anodised grill DG- 202 ( 10 mm x 5.2mm ) of Deco grill or equivalent fixed with 'F' section size not less than 20.60 x 15.20 x 1.5mm thick of approved make all as specified and directed. Note : (i) Make shall be of M/s Decogrille of M/s Associated Groups or equivalent as approved by the GE. (ii) Minimum thickness of anodizing shall be 15 microns.

Supply only for 6mm thick bakelite sheet prelaminated both side with decorative choice laminations with aluminium frame cuboard shutter work complete all as specified and directed.

S&F 100 mm stainless steel butt hinges,complete all as specified and directed

S&F 150mm length brass decorative type barrel tower bolt of extruded section complete all as specified and directed

S&F 150 mm length decorative type brass handles,fabricated type, anodised complete all as specified and directed

S&F 200mm decorative type brass Mortise lock with handle system all as spd and directed.

S&F brass decorative type 250mm size sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

Dismantling of ceiling board (fibre, pulp,insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets etc complete all as specified and directed.

S&F 35 MM thick IInd class hardwood plain framed panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm venered particle board with commercial veneering on both face . The size of rail and stiles as per IS 1003

M & L for false ceiling of galvanised iron frame work of angle section of 15 x 15 x 28 gauge for support and main U section of 40 x 20 x 26 Gauge and supporting U clip of 32 x 18 x 26 Gauge and gypsum board of 12.5 mm thick in panels fixed to GI frame work including cutting, bolting, welding etc of GI frame work and providing POP finish to the ceiling and applying two coat of OBD complete all as to the satisfaction of Engr - in - Charge

S&F 40mm thick factory made flush door shutter ,solid core construction with particle board core both faces is covered with decorative face veneer with liping match the frame all as spd and directed

M&L for Ist class Hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joint complete all as specified and directed.

M&L for french polishing on surfaces of any description width or girth including cleanning and preparing the surface and applying two coats over one coat of wood filler all as spd and directed

S&F in repair PVC cabinet mirror of minimum size 450X313 mm complete all as specfied and directed.

Dismantling cast iron pipe of any description etc complete all as specified and directed

S&F 75mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps8mm dia with two nuts wall nails etc complete all as specifed and directed.

S&F 110mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps8mm dia with two nuts wall nails etc complete all as specifed and directed.

S&F 75mm bore PVC (SWR) bends any radius dimnishing pieces or tapers with access doors etc, complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends any radius dimnishing pieces or tapers with access doors etc, complete all as specified and as directed.

M&L for removal of loose and disintegrated concrete of RCC structural members viz slab, beam, column and lintel etc by low impact hammer including removal of debris outside MD land. Cleaning of exposed reinforcement bars with wire brush and apply two coats of anti-rust protective chemical at suitable intervals all as per manufacturer's instructions to resist further deteoration of reinforcement bars. Apply approved epoxy based bonding coat on concrete surfaces to achieve sound bond between existing and new concrete. M&L for profilling of structural members with polymer modified mortar 1:3 mixed with and including 15% latex polymer by weight of cement (w/c ratio 0.35) including leveling to match the surface. Application of complete treatment shall be through approved applicator all as per manufacturers instructions (Bauchemic Krishna or Sunanda) including scaffolding for following 20mm average thickness of polymer modified mortar complete all as specified and directed

S&F in repairs 1000 ltrs Rotational mould polyethylene water storage tanks triple layer (cylinderical vertical with closed top) hoisted and fixed in position all as specified in ssr part-I complete all as specified and directed

M&L for 20 to 25mm thick machine cut and machine polished cudappa stone slab for kitchen plateform jointed and set in CM 1:3 and fi fixed including rounding to edge of stone slabs one side edge etc complete all as specified and as directed

S&F in repair stainles steel sink with drainage board , 1 mm thick sheet of steel grade AISI 304 for kitchen or laboratory, with plug, waste pipe, washers including CI cantilever bracket, connecting union etc., overall size 915 x 460 mm with bowl size 410 mm x 330 mm x 160 mm including supply and fixing bib tap CP with long body screwed for iron pipe complete all as specified and directed. Make : Nirali, Bule star ISI marked.

M&L for Preparation of new steel surfaces of any description, over 10 cm in which or girth, not otherwise descrided two coats of synthetic enamel paint over coat of zinc chromium paint complete all as specified and directed.

M& L for 80mm thick Machine pressed precast paver block M-40 grade laid over sand cushioning after consolidation set and levelled the paver block on proper level with inter locking and size conforming to IS 15658-2006 with grey cement and pigment (LAQUER FINISH) etc complete all as specified and as directed Note: sand cushion will be measured separetely .Make - Super tiles/NITCO Tiles/VITCO tiles

Supply only sand cusion for paver blocks

M&L for post construction anti- termite traetment along the external wall below concreate or masonary apron using chemical emulsion @2.25 liters per linear meter including drilling and plugging holes with cement morter 1:2 to match the existng floor etc complete all as specified and directed.

M & L for post construction anti - termit treatment at points of contract of wwod work using chemical emulision (in oil or kerosin based solution ) @ 0.5 liters per holy by drilling 6 mm dia holes at a down ward angles of 45 degree at 150 mm centere to center and sealing the same with white cement and making good to the existing surfaces etc complete all as specified and directed.

M&L for injecting chemical GLYPHOSPHATE 41% SL 20 ml or till refusal by making cuty/injection of the stem of plant 30 mm C/C and spraying with solution (25 ml GLYPHOSPHATE 41% diluted with 1 ltr of water) and removing the plant/vegitation including penetrated roots complete including necesary scaffolding etc all as specified and directed for plants/vegetation

S&F in repair for Stainless steel railing of special alloy (grade 304) pipe 1.50 mm thick and any dia of pipe, incl necessary cutting , notching organ welding , grinding and drlling counter sunk holes and bending required shape by mechanical means in factory as per requirement without forming wrinkles and butting polishing all as spd .

S&F in repair designer etching glass 5mm thick fixed in doors , windows , ventilators etc including all fixing materials ,wooden/ rubber beading, all as spd and directed.

M&L for elevation wall exterior tiles of any size fixed on wall surfaces with cement mortar 1:4 with all pigment to match the shade of tiles . All as spd and directed

S&F for 20mm dia fancy type chromium plated curtain rods with fixing fancy brackets, brass screws etc complete all as specified and directed

Taking down carefully copper/aluminum point wiring of any type such as Concealed/surface/batten/casing and capping (light fan, socket or power) complete including fitting such as switches, ceiling roses, pendants, lamp/bracket holders, sketch/bulk head fittings, regulators, sockets, board outlets etc and making good the disturbed surfaces of walls, floor, ceiling etc for rewiring and repairs etc.

Demolition of cement concrete (reinforced cement work) of any description and in any position not otherwise specifically provided and disposing off the rubbish outside MD land complete all as specified and directed.

Demolition of cement concrete (unreinforced ) of any description and in any position not otherwise specifically provided and disposing off the rubbish outside MD land complete all as specified and directed.

M&L for point wiring for light/fan controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC concealed conduit having thickness not less than 2 mm with all fittings including modular steel sunk box having thickness not less than 2 mm including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour and all as specified .Note: colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)(Make of copper wire:Le Grand/Havells/Polycab and PVC conduit Make: Precision,Plaza)

All as per srl item No 98 above but for call bell point.

All as per srl item No 98 above but for 5 pin 5 amps socket outlet on the same board with other switch all as specified.

All as per srl item No 98 above but for 5 pin 5 amps socket outlet indenpendent board of light point all as specified.

M&L for point wiring with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLSH with and in and including PVC concealed conduit having thickness not less than 2 mm with all fittings including modular sunk box having thickness not less than 2 mm including 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLSH as earth continuity conductor connected to common earth dolly.and including cutting chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching existing colour and all as specified . Note: colour coding is to be maintained .(Ph-Red, N-Black, Half-Yellow, Earth- Green)(Make of copper wire:Legrand/standard/Havells and PVC conduit Make: Precision,Plaza)

M&L for point wiring with 4 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and in and including PVC concealed conduit having thickness not less than 2 mm with all fittings including modular sunk box having thickness not less than 2 mm including 4 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly.and including cutting chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching existing colour and all as specified . Note: colour coding is to be maintained .(Ph-Red, N-Black, Half-Yellow, Earth- Green)(Make of copper wire:Legrand/standard/Havells and PVC conduit Make: Precision,Plaza)

M&L for submain wiring in and including PVC conduit having thickness 2 mm, 25 mm dia with two run of PVC insulated, sheathed multistranded copper conductor of 10 sqmm(FRLS) and one run of PVC insulated, sheathed multistranded copper conductor 10 sqmm (green in color) for earth continuity conductor and connected to common earth dolly with thimble etc, cutting chiseling for concealed piping and making good the disturbed surface area white wash/colour wash to matching with existing colour complete all as specified and directed.. (Note: Two run of 10 sqmm plus one run 10 sqmm of earth wire will be measured as 1RM) including dismantling of existing unserviceable submain wiring all as specified and directed.Make:Legrand/Havells/polycab Note: colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)

M&L for ceiling rose three terminals AC 240 volts 50Hz complete all as specified of make: Havells/Legrand/Cona

Supply and fixing bell ding dong AC 240 volt Ac 50Hz complete all as specified and directed.

Supply and fixing modular ceiling fan regulator 120 watt 2 module AC 240 volt complete all as specified and directed.

M&L for switch modular one way 6/5 amps 1 module complete all as specified.of make: legrand/ Havells/Elvira(Indo Asian)

M&L for switch modular one way 16/20 amps 1 module complete all as specified.of make: legrand/ Havells/Elvira(Indo Asian)

M&L for socket modular 6Amp 2/3 pin combined 2 module complete all as specified and directed.

M&L for socket modular 6/16 Amp 2/3 pin combined 2 module complete all as specified and directed.

M&L modular bell push 6Amp 1 module complete all as specified andd irected.

Supply and fix in repairs sheet metal enclosure powder painted for MCB DB SPN 8 way double door with din rail and 200 Amp bus bar complete all as specified and directed. Make: Legrand/Schneider/Siemens

Supply and fix in repairs MCB SP 240 Volts 6 to 32 Amps breaking capacity 10 KA rating "B" Curve complete all as specified and directed.Make: Legrand/Schneider/Siemens

Supply and fix in repairs MCB SPN 240 Volts 32 Amps breaking capacity 10 KA rating complete all as specified and directed.Make: Legrand/Schneider/Siemens

Supply and fix in repairs sheet metal enclosure powder painted for MCCB vertical TPN DB 4 way double door with din rail and 200 Amp bus bar complete all as specified and directed. Make: Legrand/Schneider/Siemens

Supply and fix in repair MCCB 125 Amp 4 pole, 415 Volt adjustable type with breaking capacity 16 KA from panel boards etc complete all as specified and directed. Make: Legrand/Schneider/Siemens

Supply and fix MCB TPN, 415 volt 40 To 100 Amp breakng capacity 10 KA rating complete all as specified and directed. Make: Legrand/Schneider/Siemens

Supply and fixing modular metal flush box 1/2 module complete all as specified and directed.

Supply and fixing modular metal flush box 3 module complete all as specified and directed.

Supply and fixing modular metal flush box 4 module complete all as specified and directed.

Supply and fixing modular metal flush box 6 module complete all as specified and directed.

Supply and fixing modular metal flush box 8 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame 1/2 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame 3 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame 4 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame 6 module complete all as specified and directed.

Supply and fixing modular white cover plate with frame 8 module complete all as specified and directed.

Supply & Fixing for tube light fitting LED 20 watt made out of CRCA sheet powder coated complete with housing t with aluminium heat sink on back of leds ,power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting and shall be fitted on new plastic square/round block ,warm white/cool white as per site requirement complete all as per specified and directed. Make: Havells /CG/Luker/Shakti Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Supply & Fixing for tube light fitting LED 10 watt made out of CRCA sheet powder coated complete with housing and with aluminium heat sink on back of leds,power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting and shall be fitted on new plastic square/round block, warm white/cool white as per site requirement complete all as per specified and directed. Make: Havells /CG/LUKER/Shakti Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Material and Labour for LED Panel Luminaire 600mm x 600mm (2"x2") 35/36 watt recess mounting with polymer diffuser with ,power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting warm white/cool white as per site requirement complete all as per specified and directed. Make: Havells /CG/Luker/Shakti Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Material and Labour for LED Panel Down Light Fitting 09 watt(Square in Shape) Warm white recess mounting with opaque diffuser,power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting and shall be fitted on new plastic square/round block warm white/cool white as per site requirement complete all as per specified and directed. Make: Havells /CG/Luker/Shakti Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Material and Labour for LED Panel Down Light Fitting 12 watt(Square in Shape) surface mounting with opaque diffuser with,power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting complete all as per specified and directed. Make: Havells /CG/Luker/Shakti Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Supply & fix LED Panel Down Light Fitting 12 watt (Round in Shape) warm white in colour recess mounting with opaque diffuser with ,power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting warm white/cool white as per site requirement complete all as per specified and directed. Make: Havells /CG/Luker/Shakti Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Material and Labour for LED Wall Mount Light Fitting 07 watt surface mounting made out of CRCA sheet powder coated complete with housing ,power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting warm white/cool white as per site requirement complete all as per specified and directed. Make: Jaquar JNL-CHR-WLSL55004E27 Equivalent in other makes Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Material and Labour for LED Wall Mount Light Fitting 4 watt warm white in colour surface mounting with ,power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting warm white/cool white as per site requirement complete all as per specified and directed. Make: Jaquar Cat Part No. KCH-CHR-MB160275531B equivalent in other makes Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Taking down existing ceiling fans and re-fixing the same ceiling fan and exhaust fan any sweep including provisioning of cable from celing rose toc/ fan and spry painting of ceiling fan/Exhaust fan with two coats of synthetic enemal paint complete all as specified and directed.

Supply and fixing modular motor starter 25 Amp 2 module for AC complete all as specified and directed.Make:Legrand /Schneider/Seimens

Material and labour for rewinding of stator assembly of exhaust fan 300/450 mm sweep after strip opening of motor with proper grade/guage of super enamelled copper wiring incl all insulating materials, re-assembling and replacement of worn out nuts, bolts, rubber bushes, clamps etc complete all as specified and directed by Engr-in-Charge. Note :- Taking down cleaning, greasing and re-fixing in positionetc complete all as specified and directed.

Material and labour for rewinding/replacing of stator assembly of plastic body exhaust fan 250/300 mm sweep after strip opening of motor with proper grade/guage of super enamelled copper wiring incl all insulating materials, re-assembling and replacement of worn out nuts, bolts, rubber bushes, clamps etc complete all as specified and directed by Engr-in-Charge. Note :- Taking down cleaning, greasing and re-fixing in positionetc complete all as specified and directed.

Servicing of complete solar light fitting including cleaning the terminals and replacing unserviceable brass battery clamps and toping up of distilled water including cleaning of solar pannels on 5 mtr height pole/roof top - 5 Nos solar light fittings/pole complete all as specified and directed.

Material and Labour for bed side wall LED Light Fitting 3 watt , power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting and complete all as per specified and directed. Make: philips / Havells /CG/Luker Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Material and Labour for focus LED 3 watt Light Fitting watt , power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core copper flexible cable of size 23/.0076 from ceiling rose/PVC connector to light fitting and complete all as per specified and directed. Make: Havells /CG/Luker/Shakti Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Material and labour LED post top lantern 40 watt power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core PVC copper cable unsheathed from FRP street light control connector to light fitting and complete all as per specified and directed. Make: Havells /CG/Luker/Shakti Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

Material and labour out door gate light LED 10 watt power factor >0.9,having inbuilt surge protection device for overvoltage protection with all accessories prewired and making connection with 3 core PVC copper cable unsheathed from FRP street light control connector to light fitting and complete all as per specified and directed. Make: philips / Havells /CG/Luker Note:1.Contractor shall produce LM79 & LM80 test reports from OEM owned NABL accredited laboratory.Contractor shall also produce certificates for power factor and surge protection from the company at no extra cost.

M & L for earthing complete with Copper earth plate electrode 60 cm x 60 cm x 3.15 mm thick buried directly in ground vertically at a depth not less than 2.25 m below normal ground level with top level of earth plate at depth not less than 1.5 m below normal ground level surrounded form all sides by 15 cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connection by using Copper strip 32 mm x 6 mm by means of bolts, nuts, check nuts and washers of Stainless Steel upto test point and protected by GI pipe light grade 40 mm bore up to 7.5 Mtr connected to a main switch board or main control board and GI pipe light grade 20 mm bore for watering and including funnel, wire mesh, 80 mm thick pre-cast RCC 1:2:4, type B-1 cover reinforced with hard drawn steel wire fabric weighing not less than 4 Kg/Sqm in lieu of CI cover, PCC 1:3:6 type C2 pit / chamber including all necessary excavation and earth work, disposal of surplus soil to a distance not exceeding 50 m all as specified and as shown in Electrical Plate No3 of MES Schedule Part – I of 2009.

mp construction co

the bhimani group of companies

Star Construction Co.

Vishal Builders

R J ENTERPRISES