RequiredExperience with Government
RequiredOEM Annual Turnover Bid to RA enabled No Water Cannon Vehicle ( 2 ) ( Under PAC ) Make tatamotors Model tata12klwatercannonlpt25186x2bsiv-police Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) Certifications Water Tanker Capacity 11000 11000.0 - 12000.0 Or higher Certification ARAI/VRDE/ICAT For Chassis * Certification ARAI/VRDE/ICAT No AAKN 0329 * 1/12 Form 22 A - For compliance with pollution standards
Requiredsafety standards of components and road worthiness as per CMVR Rules Yes * Registration to Local RTO (Regional Transport Office)/RTA(Regional Transport Authority) by seller However NGT approval needs to be provided by the Govt Department Yes * Availability of test reports for all critical components from the manufacturer or OEM of Jetting Pumps
RequiredPower Take Off unit
RequiredSprinkler Hose etc shall be from any ILAC/NABL accredited/Central Govt Lab To be furnished to buyers on demand Yes * Conformity to technical requirements As per attachedspecification for VehicleMounted Water CannonSystem for Riot ControlOperations approved byDRDO vide SpecificationNo. -RDE/9 7017/DCS/WC/12000 except for the model specified for the chassis
Requiredsupplier can use any chassis of GVW 25000kg and drawings as provided by buyers * Specification has been seen and understood Yes * Testing should be done as per QR attached Yes * Generic Parameters Engine Capacity 5883 * Make of Chassis Tata 2518 6x2 * Chassis Model No Tata 2518 6x2 BSIV * Category of Vehicle for which Chassis to be Heavy Capacity Commercial Vehicles * 2/12 used Body Style 12KL water Cannon * Body Options Fixed Side Deck Fixed Side Deck Type of Fuel Diesel * Vehicle Emission Compliance BS-IV * Vehicle Mileage ( declared by OEM as certified by Test Agency under Rule 115of CMVR 1989) (kmpl) 5 * Maximum Speed 78 * Engine Power BHP 180 More than 180.0 Or higher Rated RPM for Max Engine Power 2500 * Engine Torque Max (Nm) 700 * Rated RPM for Max Engine Torque 1600 * Engine Aspiration Water Cooled Direct Injection Turbocharged * No of Cylinder in Engine 6 * Fuel Tank Capacity 350 350.0
Required350 Overall Length (<=9350mm if eqpt is offered in accordance to DRDO Specs 9050 Less than 9050.0 Or lower Overall Width (<=2470mm if eqpt is offered in accordance to DRDO Specs 2480 Less than 2480.0 Or lower Overall Height in accordance with the norms laid down by the State Transport Department * Gradeability of Chassis (%) 28 * Minimum Ground Clearance 248 More than 248.0 Or higher Wheel Base 4880 More than 4880.0 Or higher 3/12 Kerb Weight 6150 * Gross Vehicle Weight 25 25.0 - 25.0 Or higher Front Axle weight 6000 More than 6000.0 Or higher Rear Axle weight 19000 * No of Axle 2 2 Axle Configuration ( No of Outside Tyre x No of Driving Tyre) 6x2 * Type of Front Axle and Suspension System Reverse Elliot
RequiredLS * Type of Rear Axle and Suspension System Fully floating
RequiredLS * BIS marked Pneumatic Tyres and tubes for both front and rear Yes * Size Of Front Tyres 10.00 R 20 16PR * Size Of Rear Tyres 10.00 R 20 16PR * Size of Wheel 508 508 Chassis Transmission System Manual Manual No of Speed Forward Gears 6 6 Type of Steering Power Power Turning Radius 10250 10250.0
Required10250 Speed Governers with valid certification Yes Yes ABS Fitted Yes Yes Front Vehicle Brake Full Air S-Cam * Rear Vehicle Brake Full Air S-Cam * Type of Clutch Single Plate * Side View Mirror Yes Yes Low Fuel warning Light Yes Yes Fog Lights Yes Yes Standard Sparewheel and Tool Kit Yes * Constructional Parameters Seating Capacity (in the cabin) 2 2 Seating Capacity layout with dimensions Yes * 4/12 Nominal Thickness of MS Plate used for fabrication of water tank to IS:1730 latest and IS :2062 latest for E-250BR steel grade 5 5.0
Required5 Size of channel used for frame for mounting on chassis 100mm x 50mm * Dimensions (L X W X H) 9050x2480x3600 (mm) * Gross weight of Water Tanker 1680 1680.0
Required1680 Total capacity of water tank 11000 11000.0
Required11000 Net water carrying capacity of Water Tank 12000 * Material of Water Tank MS * Thickness of Water tank at bottom
Requiredfront and rear 5 More than 5.0 Or higher Thickness of Water tank at side and top 5 More than 5.0 Or higher Thickness of baffles 3.15 More than 3.15 Or higher Diameter of Bolted manholes 450 * Diameter of Filling orifice 325 More than 325.0 Or higher Diameter of Drain Cock 75 More than 75.0 Or higher Internal diameter of Overflow Pipe 100 More than 100.0 Or higher Number of Filling pipes 2 * Internal diameter of Filling Pipe 70 More than 70.0 Or higher Diameter of Male Coupling fitted with filling pipe 63 63 Or higher Tube type Water level Indicator calibrated as empty
Required1/4
Required1/2
Required3/4 and Full should be provided Yes * Length of Water Filling pipe 50 * Provision of Self-filling Yes * 5/12 of water tank directly from pump Type of Pump Single Stage Centrifugal pump Single Stage Centrifugal pump
RequiredTwo Stage Centrifugal pump Pump connected with Water tank
RequiredWater cannon and spray nozzles Yes * Various controls of operating the pump at pump control panel and in drivers cabin also Yes * Material of Pump casing and Impeller Gun Metal * The pump shall be capable of giving the performance when working with all internal and external strainer at sea level and upto 35°C water temperature Yes * Water Flow (Output) 3200 @ 8.5 kg/sqcm
Required2400 @ 10.5 kg/sqcm 3200 @ 8.5 kg/sqcm
Required2400 @ 10.5 kg/sqcm Suction lift measured vertically from water level 3 * At rated RPM 2400 * Diameter of Suction Hose 100 100.0
Required100 The pump shall be connected with water tank
Requiredwater cannon and spray nozzles Yes * The primer shall be capable of lifting water at least from a depth of 7m at a rate not less than 30CC/sec through a suction bore of 100mm dia and shall preferably be of the water ring/exhaust ejector type Yes * Auxilliary engine for driving pump Yes * Number of cylinders 6 * Type of Auxilliary Water cooled diesel * 6/12 engine engine Max Engine Power 130 * Rated RPM at Max engine power 2400 * Controlling of operating temperature of engine cooling water Thermostatically Controlled * No of Irritant and Indelible Ink tanks 2 * Capacity of each tank 500 * Material of tank SS-304 * Thickness of walls of tank 5 More than 5.0 Or higher Hydraulic pressure of tanks to be withstand (kg/sqcm) 0.3 * Diameter of filling orifice of each tank 325 More than 325.0 Or higher Diameter of Drain cock and pipe 75 More than 75.0 Or higher Suitable venting arrangement shall be provided Yes * Tube type level indicator for ink and irritant tanks calibrated as empty
Required1/4
Required1/2
Required3/4 and Full should be provided Yes * Inductor and Selector valve should be fitted with proportionator valve to ensure correct intake of irritant/indelible ink from 0 to 8% Yes * No of Water Cannons 2 * Operation of Water Cannon Electro-pneumatically Electro-pneumatically Mounting of Water Cannon Roof of vehicle * Operated by means of Joysticks * Each cannon should be capable of transversing through 0° to 210° in azimuth and from -15° to +60° in elevation Yes * 7/12 Searchlight fitted with each cannon Yes * Provision of Manual override control of water cannons in case of failure of electrohydraulic control Yes * Water Flow from each Cannon 1100 @ 10.5kg/sqcm * Distance of Water Jet Throw 50 More than 50.0 Or higher Water Cannon fitted with Pulse jet arrangement Yes * Pulse Jet Arrangement both for Pulse and Continous jet throw arrangement Yes * Discharge water Pulse duration 2 Sec ON & 2 Sec OFF * Switchover from continous system to pulse jet arrangement Yes * To protect the vehicle tyres during operation
Requiredtwo spray nozzles at front and rear shall be provided with wide jet pattern to cover an area twice the width of vehicle Yes * Adequate sitting arrangement for driver and team should be in driver's cabin
RequiredMaximum possible vision and adequate ventilation should be provided in cabin
RequiredThe doors should open outwards and the glasses on doors and windows should be fitted with polycarbonate sheets
RequiredWindscreen of splinter proof safety type shall be provided Yes * All glasses shall be provided with removable protective wire mesh screen of 10 Yes * 8/12 gauge wire dia and 25 mm openings
Requiredwiremesh also to be provided on head lamps and other lights oh vehicle Material used for panelling and locker Aluminium sheets * Thickness of material used for Panelling and locker 1.62mm (16 gauge) * Checkered plate shall be provided on top of the entire vehicle Yes * Lockers shall be provided for stowage of all the accessories
Requiredspares/tools Yes * Locker shall be fitted with internal automatic lighting and should be weather proof and self draining to release all water following a washdown Yes * TFT moniter provided in driver cabin Yes * Size of TFT Monitor 14 * Video camera shall be mounted on a stand provided inside the rear door of the vehicle Yes * Operation of Video Camera and TFT 12 Volt DC vehicle Battery * An additional compressed air cylinder shall be provided for pneumatic systems Yes * No over-turning should occur beyond 27° slope from the horizontal (under fully equipped and loaded conditions) Yes * Instruments and control Pneumatic controls for Water Supply for water cannon
Requiredcooling system
Requiredinductor
Requiredrear and front tyre saving spray nozzle Yes * 9/12 Pneumatic control for indelible and irritant ink supply for mixing with water Yes * Pneumatic Control for Selector valve and control for air release Yes * Hydraulic Auto/Manual controls for oil hydraulic system for cannon movement Yes * Elevation for cannon Yes * Azimuth for cannon Yes * Mechanical Control lever for water supply from water tank to pump valve Yes * Callibrated Pressure gauge (0 to 21kg/sqcm) Yes * Callibrated Vacuum gauge (0 to -1 kg/sqcm) Yes * Control for engine throttle Yes * Control lever for priming and exhaust primer valve Yes * Water supply control for cooling system Yes * Water supply control from pump to water tank filling valve Yes * Suction mouth Yes * Delivery Valves Yes * Tools and documents All tools required for normal maintenance of vehicle and system shall be provided along with the system Yes * User Handbook
RequiredTechnical Manual
RequiredIllustrated part identification list shall be provided Yes * CCES and Equipment Dossier Yes * Detailed Drawing of the Yes * 10/12 product available Markings of Manufacturers name or trade mark
RequiredYear of manufacture
RequiredCapacity of pump
Requiredwater tank
Requiredirritant tank and indelible tank
RequiredEngine and chassis number and Pump number should be present Yes * Accessories No of Armored Suction hose in 2point5 m length with internal dia of 100mm with standard round thread coupling (IS:902/2410) 4 * No of Low level suction strainer (IS:907) 1 * No of Basket strainer for low level suction strainer (IS:3582) 1 * No of suction wrenches (IS:4643) 1 pair * No of Suction collecting head 3-way 1 * No of suction adopter to hydrant 100mm X 63mm 1 * No of RRL Hose 63mm dia and 30 m long
Requiredwith instantaneous IS-636 II and IS-903 2 * No of Light alloy branch pipe with 19 and 25 mm nozzles 2 sets * Front Bumper Hook Yes * Rear Hook Yes * Fire Extinguisher Yes * Performance Parameters Warranty Time 12 More than 12.0 Or higher Warranty Distance 20000 * Battery Warranty 12 More than 12.0 Or higher No Of Free Service 3 More than 3.0 Or higher * Bold specifications are the golden parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer. 11/12
