CERTAIN REPAIR TO ALUMINIUM DOORS, PAVING, CEILING, FLOORING, SANITARY FITTINGS, ROOF SHEET, REPAIR/REPLACEMENTANDCLEANING SERVICE TANKS AND REPAIR/MAINTENANCE OF LIGHTENING PROTECTION SYSTEM OF BLDGS IN DOMESTIC/TECHNICAL AREA AND OTHER MISC WORKS A

Amount

Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish to a distance n.exc 100m complete all as directed.

M & L for 75 mm thick, plain cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in hardstanding/path etc, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M & L for 50 mm thick, plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in floors and finishing the surfaces even & rough complete all as specified and directed.

Demolition of reinforced cement concrete in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

M & L for Reinforced Cement Concrete 1:1.5:3, Type A-1 (Nominal Mix) (Using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, etc complete all as specified and directed. (Note : Reinforcement will be measured & paid seperately)

M & L Reinforced Cement Concrete 1:1.5:3, Type A-1 (Nominal Mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed. (Note : Reinforcement will be measured & paid seperately)

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, etc and set in cement mortar 1:4 including necessary form, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

M & L for use & waste Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizonal or sloping) for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etcetc complete all as specified and directed.

M & L for Precast reinforced cement concrete 1:2:4, type B-0 (using 12.5mm graded stone aggregate) louvres and jallies, 25mm thick including all mouldings and set in cement mortar 1:6 complete all as specified and directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc stacking the serviceable bricks after removing mortar and cleaning for re-use and disposal of debris and rubbish to a distance n.exc 100m as directed by the Engr-in-Charge.

M & L for Brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar 1:4 as in half brick thick walls complete all as specified and directed.

S & F TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F Mild steel TMT bars 5mm dia and over upto and including 10mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

M & L for pre-polished chequered cement concrete tiles 30cm x 30cm x 25mm thick, cadbury red polished and chemically treated; set jointed and pointed in neat cement slurry in floors, including 20 mm thick screed bed in cement mortar 1:6 and set & jointed in neat cement slurry and pointed in with mixture of white and grey cement equal proportion and pigment complete all as specified and directed.

M & L for granite stone slab (of any type) 18 to 20 mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 20 mm thick screed bed in cement mortor 1:4 & cutting, polishing complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for joint free non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Glazed, ceramic, coloured tiles of size 300mm x 200mm x 6-7mm thick, on vertical surfaces such as skirting, dados etc, including 10 mm thick bedding in cement mortor 1:4 and set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed, coloured, ceramic, tiles of size (350mm x 250 mm/450mm x 350mm/300mmx450mm) x 6 to 7 mm thick, on vertical surfaces such as skirting, dados etc, including 10 mm thick bedding in cement mortor 1:4 and set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Vitrified, designed, coloured, tiles, 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm, in floors, etc including 15 mm thick screed bed in cement mortor 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Vitrified, designed, coloured, tiles, 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm as in vertical surfaces such as skirting,dado, etc including 10 mm thick bedding in cement mortar 1:4 and necessary cutting of tiles complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 5 mm thick in cement mortor 1:3 on concrete surfaces as in ceilings (sunshed, chajja etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two coats (10mm+5mm each) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with integral water proofing compound with weight of cement in top layer as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

Supply only Liquid water proofing compound (ISI marked) complete all as specified and directed.

M & L for preparation new external surfaces of wall, chajja, facia etc and applying two coats of water based acrylic weather proof exterior emulsion (exterior wall finish) paint over a coat of primer as per manufacturer's instruction complete all as specified and directed.

M & L for preparation surfaces of wall/ceilings etc of any description over 10 cm width or girth not otherwise described and applying two coats of plastic emulsion paint over a coat of primer complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

S & F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exe 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n. exc 2 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 2 Sqm each complete all as specified and directed.

Refixing shutters of any description exc 1 sqm but n.exc 2 sqm each in the same opening complete as directed.

Taking down and re-fixing aluminium shutter of any description, exe 1.5 but n.exc. 4 Sqm in each and necessary re-alignment and repair and providing minor accessories etc complete all as specified and directed.

S & F Well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S & F 35 mm thick, 2nd class hardwood, factory made, Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S & F 30 mm thick, factory made, Second class hardwood, glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, etc complete all as specified and directed in SSR Part I Section 8 clause 8.24 (b).

S & F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed.

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

S & F 150 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F 100 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F Mild Steel sliding door bolts, 300 mm long, plate type, stove enamelled black, with bright bolts not less than 12mm dia with & including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, etc complete all as specified and directed.

S & F 100 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S & F 75mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type E-22 complete all as specified and directed.

S & F 125 mm size, mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S & F 125 mm size, Aluminium handles, cast type, anodised complete all as specified and directed.

S & F 100 mm size, Aluminium handles, cast type, anodised complete all as specified and directed.

S & F mild steel bands, straps, supports or stays of rain water, ventilating pipes including bolts, hooks (stay) for large gates, hook and pintel hinges, clamps, hold fasts, wall ties,flat iron fillets for securing wire mesh, wind tie, fan hook and similar work including necessary drilling bolting or riveting etc conforming to Fe – 290 Gde E – 165 complete all as specified and as directed.

M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and directed.

S & F 4mm thick non asbestos fibre reinforced designer ceiling board (610mmx610mm) with hot drip heavy duty suspended ceiling grid system T-2420 with GI frame work for seamless ceiling comprising of GI perimeter channel, unequal flanges and web etc of suitable size suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section including Hangers 6 mm dia GI fixed to roof by means of ceilling cleats made out of GI flat per manufacturers instructions after dismantling of old unserviceable ceiling complete all as specified and directed by the Engr-in-Charge.

M & L for preparing surfaces of wood and wood based materials, new or old of any description and girth, not otherwise described and treated with two coats of creosote oil complete all as specified and directed.

M & L for preparation of new wooden surfaces of any description, n.exc 10 cm width or girth when unconnected with other painting or when painted in different tint and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work complete as directed.

S & F 0.63mm thick galvanised, corrugated mild steel sheeting in roof covering having zinc coating @ 275 gms/Sqm with two corrugation side lap, fixed with L type or J type or cranked hook bolts complete all as specified and directed.

S & F 0.63 mm thick plain galvanised, mild steel sheeting as in ridges, hips, valley gutters, drip and straight flashing (length and girth as fixed) having zinc coating @ 275 gms/Sqm with two corrugation side lap, fixed with L type or J type or cranked hook bolts complete all as specified and directed.

S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed.

S & F Pre-Painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/vally gutter, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed.

S & F in repair 110 mm bore, PVC (SWR), Soil waste and vent pipes in any length with or without ears, with cement joints fixed to wall, ceiling and floor etc with all necessary fixing arrangement complete all as specified and directed.

S & F in repair 110 mm bore, PVC (SWR) bends of any radius complete all as specified and directed.

S & F in repairs, Aluminium (Die cast) body door Closer hydraulically regulated, designation No 3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

S & F in repairs 5 mm thick, sheet glass, ordinary quality and glazing with neoprene rubber beading for aluminium door/window etc in square exceeding 0.5 Sqm and n.exc 1Sqm in each pane complete all as specified and directed.

S & F in repairs 5.5 mm thick, sheet glass, ordinary quality and glazing with neoprene rubber beading for aluminium door/window etc in square exceeding 0.5 Sqm and n.exc 1Sqm in each pane complete all as specified and directed.

M & L for 12 mm thick, Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including dismantling of old unserviceable board complete all as specified and directed.

S & F Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. (Note : (i) Thickness of aluminium section shall not be less than 1.5 mm.)

S & F powder coated (minimum 15 micron aluminium anodised door comprising of frame of size 101.60mmx44.6mmx2.4mm thick push/pull type glazed door shutter having top and bottom section 83x44.5x2.4mm and 100x44.5x2.4mm thick respectively, styles section 80x44.5x2.4mm thick and lock rail of size 100mmx44.5mmx2.4mm thick including necessary jointing cleat, glazing clips, rubber packing, anodised aluminium snap beading, screws of suitable size including 5mm thick tinted sheet glass in both panel, hinges, mortice lock, stays & aluminium anodised handle of suitable size, etc complete all as specified and directed.

S & F in repair aluminium welded grill of mesh size 90mmx90mm of aluminium bars having cross section area not less than 30 Sqmm, decorative type including frame and necessary fittings etc complete all as specified and directed.

S & F in repair Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S & F in repair Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F in repair Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M & L for Mild steel framed work such as grills, gratings, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-410-0 Gde E-250 complete all as specified and directed.

Taking down steel window/ventilators shutter of any size and description and refixed in the same opening after minor repairs/welding including provision of box type hinge and necessary minor accessories as required complete all as directed

M & L for Rolled mild steel fo grade Fe 410-W (Gde-E- 250) quality-A as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat section) including distance pices, cleat etc complete all as specified and directed.

Taking up or down 15mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed.

Taking up or down 20mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed.

Supply, laying, connection and testing, 15mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

Supply, laying, connection and testing, 20mm bore, Steel water tubing, galvanised, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, etc complete all as specified and directed.

Refixing of 15mm bore old serviceable steel tubing and connections in new or old position with new fittings complete to walls and ceilings or laid in floors, etc complete as directed. (Note: Serviceable pipe shall be reused as obtained from serial item No. 86 above)

Refixing of 20mm bore old serviceable steel tubing and connections in new or old position with new fittings complete to walls and ceilings or laid in floors, etc complete as directed. (Note: Serviceable pipe shall be reused as obtained from serial item No. 87 above)

S & F 500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top), hoisted and fixed in position including taking down old unserviceable one as specified in SSR Part I and directed.

S & F 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top), hoisted and fixed in position including taking down old unserviceable one as specified in SSR Part I and directed.

S & F 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms) complete all as specified and directed.

S & F in repair 15 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 142 gms) complete all as specified and directed.

S & F in repairs, Vitreous China wash basin with pedestal, counter type oval shape, pastel colour, flat back of size 580 x 450 mm excluding taps but including CP waste coupling, PVC waste pipe, chain, plug & porcelain stopper, bracket complete all as specified and directed.

S & F in repairs, vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and directed.

S & F in repairs, Vitreous China bowl urinal flat back, of size 465x355x265mm, white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete as specified and directed.

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and flushing pipe, anti syphonic pipe with seat and cover complete but excluding flushing cistern & flush pipe including making good damaged/disturbed surfaces complete all as specified and directed.

S & F in repairs, 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and directed.

S & F in repairs, Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed

S & F in repairs, stainless steel kitchen sinks with drainage board made of 1 mm thick sheet for kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repairs, stainless steel sinks made of 1 mm thick sheet with plugs, washers and wastes including bedding in ement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repair 32 mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S & F in repairs, 15mm bore, bib taps of PTMT, any colour high pressure, screwed for iron pipe and fixed (minimum weight 90 gms) complete all as specified and directed.

S & F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and directed.

Supply & fixing in repair 15mm bore pillar tap fancy type of PTMT, any colour, high pressure, screwed for iron pipe and fixed (minimum weight 120 gms) complete all as specified and as directed.

S & F in repairs, swival shower of PTMT 15mm bore (minimum weight 40 gms) complete all as specified and directed.

S & F in repair Grating doom 140mm dia of PTMT (Minimum weight 50gms) complete all as specified and directed.

S & F in repairs, cast iron nahani trap 100 mm dia with grating including jointing to waste pipe fixed in cement mortar 1:2:4 type B1 using 20mm graded aggregate complete all as specified and as directed.

M & L for Plain cement concrete 1:2:4, type B-0, (using 12.5 mm graded stone aggregate) as in benching, coping, etc incuding necessary form works etc complete all as specified and directed.

M & L for Cutting existing steel tubing 15 mm bore for alteration or additions (Each cut measured) complete all as specified and directed.

M & L for Cutting existing steel tubing 20 mm bore for alteration or additions (Each cut measured) complete all as specified and directed.

M & L for Screwing existing steel tubing, 15mm bore for alterations or additions (or lengthening screw on pipe to form connector) complete all as specified and directed.

M & L for Screwing existing steel tubing, 20mm bore for alterations or additions (or lengthening screw on pipe to form connector) complete all as specified and directed.

S & F in repairs 40 mm dia, High density poly-ethylene pipes, (HDPE) of pressure rating 6 kgf/cm 2 laid as in waste pipe of WHB etc complete all as specified and directed.

S & F in repairs, 15mm bore, bib taps, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs, 15 mm bore, Stop valves, cast copper alloy, chromium plated with long shank and cup, concealed type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repair 15 mm bore, health faucet ABS body with wall hook and 1 m long SS braided rubber hose pipe with all accessories complete all as specified and directed. (Make: Cera Cat No. CG-106 or equivelant of approved make)

S & F in repairs, Toilet paper holder, brass, chromium plated fixed to wall with brass screw complete all as specified and directed.

S & F in repairs, 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks of capapcity exc 250 & n.exc 500 Ltrs and from mouths of circulating pipes, etc. using bleaching powder and washed with water including dismantling and reconnecting and refixing in psoition including writing date of cleaning with white synthetic enamel paint as "CLEANDED ON" complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks of capapcity exc 500 & n.exc 1000 Ltrs and from mouths of circulating pipes, etc. using bleaching powder and washed with water including dismantling and reconnecting and refixing in psoition including writing date of cleaning with white synthetic enamel paint as "CLEANDED ON" complete all as specified and directed.

M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

S & F in repair 20 mm bore, gun metal, Gate valves with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

M & L for Welded steel wire fabric, n.exc 4Kg/Sqm supplied and fixed complete to wood or steel members complete all as specified and directed

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed.

S & F 12mm thick toughen glass exc 0.50 sqm in each panel, matching with existing design as directed by Engg in Charge including all accessories of glass door (i.e. stainless steel handle, hinges, door stopper, floor spring including taking down old broken glass complete all as specified and directed.

S & F in repair Air termination, single pointed copper rod 12mm dia and 300mm long complete all as specified and directed.

S & F in repair Air termination, single pointed Aluminium rod 12mm dia and 300mm long complete all as specified and directed.

Fixing only in repair Air termination, single pointed Aluminium/copper rod 12mm dia and 300mm long complete all as specified and directed.

M & L in repair for Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed.

S & F Copper strip 20 x 3.00mm with Saddles and fixing screws etc for roof conductors and down conductors above ground level including taking down the old one complete all as specified and directed.

S & F Copper strip 32x6mm buried in ground including taking down the old one complete all as specified and directed.

S & F aluminium strip 25 x 3.00mm with Saddles and fixing screws etc for roof conductors and down conductors above ground level including taking down the old one complete all as specified and directed.

S & F Galvanised iron strip 32x6mm buried in ground including taking down the old one complete all as specified and directed.

S & F in repair earth continuity conductor or main earthing lead with galvanised iron wire 4mm dia, fixed to wall on batten or recesses or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc, as required complete all specification and directed.

S & F in repairs porcelain vitreous white/brown/green spacers insulator of size 75x35x40mm high complete with one number galvanised iron stud, bolts 6mm dia, 40mm long including nuts, bolts & washers and two numbers galvanised iron fixing bolts of size 6mm dia and 50mm long including washers and drilling holes for holding/fixing aluminium strip/roof conductor as required complete all as specified and directed.

M & L for 40 mm bore, steel tubes, galvanised, medium grade with all fittings, laid in floor/road crossing/drain etc as in cable protection complete to walls and ceilings or laid in floors including taking up or down existing pipe complete all as specified and directed.

M & L Earthing complete with copper earth plate electrode 600 mm x 600mm x 3.15 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected with copper earth strip of size 20x3mm dia by means of bolts, nuts, check nuts and washers protected by 40mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers,necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing complete incuding taking down old one as specified and as directed.

All as per serial item No. 142 above but using magnesium sulphate in lieu of common salt complete all as specified and directed.

All as per serial item No. 142 above but using copper sulphate in lieu of common salt complete all as specified and directed.

M & L for brazing of Copper strip 20 x 3.0mm over lapping of not less than 10 cm including copper rivet (5mm dia) complete all as specified and directed.

M & L for brazing of Copper strip 32 x 6.0mm over lapping of not less than 10 cm including copper rivet (5mm dia) complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for Surge protection device 40KA, 1P+N, 2 Mod complete all as specified and directed.

M & L for Surge protection device 40KA, 3P+N, 4 Mod complete all as specified and directed.

M & L for Surge protection device 15KA, 1P+N, 2 Mod complete all as specified and directed.

M & L for Surge protection device 15KA, 3P+N, 4 Mod complete all as specified and directed.

Fixing only in repair aluminium/copper/GI strip with and including new shaddles and fixing accessories etc as in roof conductor and down conductors above ground complete all specification and directed. Note: An amount of Rs.102636.00 on account of credit schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

CONSTRUCTION SHELTER

M/S BIJAY KUMAR SHIVA

SHRI D P AGARWAL

B L SHARMA

JOGINDER KUMAR GOYEL

M/S SARKAR ELECTRIC

M/S MANODEEP CONSTRUCTION