Spl repair to JCOs Md Accn (P-131 and P-140) and Spl repair for roof treatment, plastering, re-wiring of kitchen and bathroom of JCOs Md Accn (P-128 and P- 141) at Mil Stn Gaya

Amount

Demolition of reinforcement cement concrete above the ground floors n exc 15 cm thickness (Reinforcement cut as required to facilitate demolition) such as cooking platform, chajjas etc

Demolition of brick work built in cement mortar including all quions, arches, pillars, etc complete.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) all as specified

M&L for RCC as in kitchen platform, shelves & chajjas etc type B1 1:2:4 (20 mm graded aggregate) including necessary form work complete.

S&F MS TMT bar 8 dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.90mm dia or securing with clips.

Dismantling of floor, walls, roof tiles including bedding but backing and rubbish off permises all as specified.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.18 sqm & not exceeding 0.38 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match complete.

M&L for screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 for laying of floor tiles as directed.

M&L for glazed ceramics coloured tiles of size 450x350x7mm thick in vertical surfaces such as skirting/dados/wall, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces.

M&L for 10 mm thick plaster in cement mortar 1 : 4 for fixing of wall tiles complete all as specified.

M&L for machine cut cudappah stone slab 20-25 mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Taking down cement plaster on wall/ceiling/roof etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete.Note : Note : Liquid WPC will be measured and paid separately.

Supply only water proofing compound (liquid), ISI marked.

M&L 15 mm thick rendering on fair faces of bk /concrete surfaces in CM (1:6), finished even and smooth (without using extra cement ) complete.

Taking up or down steel tubing and connections, including cleaning for re-fixing of 15 mm dia.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store of 20 mm dia.

Supplyband laying of 16mm CPVC pipes SDR11& plain CPVC SDR 11 fittings on walls / ceilings or laying in floors including unions ,brass elbow, brass tee, MBTA, FBTA complete all as specified.

Supply and laying of 20mm CPVC pipes SDR11& plain CPVC SDR 11 fittings on walls / ceilings or laying in floors including unions ,brass elbow, brass tee, MBTA, FBTA complete all as specified.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete.

Taking down AC/PVC pipes (including all fittings), with spigot and socket ends and lead joints including burning out joints of 100 mm dia pipe.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete.

S&F clamp made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 110mm PVC pipe complete.

S&F PVC (SWR) bends any radius provided with access door of 110 mm dia

M/L PVC(SWR) Tee of 110mm dia etc complete all as specified and directed

S&F PVC (SWR) vent cowl 110mm bore

S&F PVC (SWR) nahani/ floor trap, plain with grating with or without waste hole including jointing with solvent cement 75mm dia etc complete

Disconnecting existing tanks, setting aside for repairing, cleaning etc and hoisting if required reconnecting and refixing position .

S&F Rotational moulded polyethylene water storage tanks in white colour tripple layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I of 1000 Ltr capacity all as spd.

S&F Ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete.

S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe complete.

S&F in repair bib tap 15 mm bore, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F in repair vitreous china WHB size 550x400 mm white flat back including pvc waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc complete.

S&F in repair vitreous china squating pan 'Orissa' pattern WC size 580x440 mm white with integral foot rest and trap and including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor all as spd.

S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete.

S&F in repair PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and as directed.

S&F in repair 15 mm bore pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly-nuts screwed for iron pipe & fixed complete.

S&F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete.

S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers and wastes, & waste pipe incl bedding in cement mortar to dwarf wall or incl fixing suitable sizes of cantilever brackets and connecting union to pipe overall size 915 x 460 mm, bowl size 410 x 330 x 160 mm complete.

S&F in repair chromium plated overhead shower rose swivel type 125 mm with CP arms 300 mm long complete all as specified and directed

Taking down chowkats or frame with shutters of any description (without taking off shutters from the frames) n. exc 1.5 Sqm each all as spd.

All as per above item No but exc 1.5 Sqm but n.exc. 4 Sqm each.

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube supplying & fixing in opening as per specified & drawing.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc fitted to chowkhats for doors etc complete.

S & F factory made 35 mm thick plain, framed, panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter are as per IS – 1003 (Part – I) made of kiln seasoned & chemically pressure treated 2nd class hardwood rail and style complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded.

DO but without glazing bar

S&F GI wire cloth 0.56 mm nominal dia of wire and average width of aperture 1 mm and fixed with stainless steel wire staple complete all as specified.

S & F 3 mm thick figured glass pin head type and glazing with oil putty in squares n exc 0.5 Sqm in each pane etc complete.

S&F 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 all as spd.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed all as spd.

S&F 100 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 300 mm long.

M & L for plain cement concrete 1:2:4 type B-0 (using 12.50 mm graded stone aggregate), as in back filling of pressed steel frames and similar workd including necessary form work as required complete.

S&F Mild steel works as in hold fasts, clamps, plain angle cleats for securing purlins to wood trusses or rafters, cooler stands and similar small articles conforming to Fe 410-0 or Fe 310-0

M & L for preparation of new steel surfaces any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of primer complete.

M&L for preparation of old wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of primer complete.

M&L preparation of new plastered or unplastered surfaces of wall and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

Preparation of old surfaces of ceiling and applying two coats of white wash.

M & L for preparation of newly plastered surfaces of wall & concrete and applying 2mm thick wall care putty including preparation complete.

M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including, rubbing with sand paper complete on newly plastered surface.

M&L for applying 2mm thick Birla / JK Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete.

M&L for applying two coats of oil bound distemper on old decorated wall including, rubbing with sand paper complete all as specified and directed.

M&L Preparing old painted surfaces of walls, chajjas etc by washing rubbing down and stopping and applying two coat of cement base paint white or tinted complete all as specified as directed.

M&L Water proofing treatment on "Non approachable / non accessible and approachable roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including taking down of existing roof treatment, properly cleaning & drying the concrete surfaces complete

(i) Applying a coat of oxidised bitumen based solvent primer @ 0.3 Kg / Sqm

(ii) Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces.

(iii) Laying unrolled over the bitumen coated surface, polymeric water proofing membrane Hyperplas standard wt not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction.

(iv) Applying two coats of bituminous aluminium paint including preparation complete

M&L for PCC 1:2:4 type B0 (Using 12.50 mm graded stone aggregate) in roof padding/kerbs/sunken slab etc complete all as spd and directed,

M&L 10 mm thick rendering on roof surfaces/concrete surface in CM 1:4 complete.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches, ceiling roses, pendent, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Taking down existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of AGE E/M complete all as specified and as directed.

Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M complete all as specified and as directed.

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLS multi stranded conductor cable in and including concealed PVC conduit of size 20/25mm ISI marked inclusive of tees, bend, elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc with white laminated 3 mm thick hylam sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLS cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One light point controlled by one, two way switch 5 Amps

(d) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

(f) One bell point controlled by one, bell switch 5 Amps

Description all as per item No 6 here in before but using 2.5 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F switch Piano type single pole 5 amp, 230 Volts complete all as specified and directed.

S & F switch Piano type single pole 15 amp, 230 Volts complete all as specified and directed.

S & F switch Piano type 2 way switch 5 amp, 230 Volts complete all as specified and directed.

S & F switch bell push piano type 5 amp, 230 Volts Complete all as specified and directed.

S & F socket outlet 2-in-1, 5 pin, 5 amp, 230 Volts complete all as specified and directed.

S & F socket outlet 2-in-1, 5 pin, 5/15 amp, 230 Volts complete all as specified and directed.

S & F ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete.

S & F stepped type electronic fan regulator flushType complete all as specified and directed.

S & F Bell push modular 6 Amps single module complete all as specified.

S & F lamp holder, PVC / Polycarbonate type with back plate suitabl for batten/ slanting fittings complete all as specified and directed.

S & F Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

S & F modular type TV Socket out let complete all as specified and as directed.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit

S & F for sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for water heater storage type (Geyser) vertical/ Horizental type as per site requirement with inner container of capacity 25 ltrs, electrically operated, AC 230 Volts,BEE 5 star rated, ISI marked including 04 Nos of hold fashner nuts required suitable size fixed in brick wall, PVC connection pipe hot & cold for JCO's Md Accn complete all as specied and as directed

S & F for ceiling fan, 230 Volts, 1200 mm sweep with service value of the fan shall be greater than 6.1 as per BIS with necessary accessories and electrical connections from ceiling rose to fan teriminal complete all as specified and as directed.

Labour only for refixing the celing fan/ Exhaust fan obtained from item No 6 above with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc. complete all as specified and as directed.

S & F for Highly efficient LED Bulbs, 10 W, used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 cap of make Bajaj, Havells, HPL complete all as specified and directed

S & F for Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and provosion of LED bulb 10 watts complete all as specified and as directed. Make Havells Cat No LHDLO6160099 or its equvalent in Philips, Bajaj.

S & F for LED 10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed. Make- Bajaj Cat Part No BCLSB 10 NW or its equivallent model in Wipro, Philips.

S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make :- Bajaj Cat No BIBWP 10W LED or its equvalent in Philips, Wipro.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Make Bajaj Cat part No BCLAB 20W WH LED P, Wipro Cat part No LL20-281-XXX065-ALI or its equvalent in Philips, Havells.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make :- Bajaj Cat part No ENXT P 24L WH CR PC SD (Edge plus series) or its equvalent in Philips, Wipro.

S & F for energy efficient exhaust fan of 230 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted).

S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

Taking down existing old Extg unserviceable LT UG/ service cable of any description and size complete all as specified and directed.

Supply & laying in trenches /laid in floor/duct/drawn through conduit XLPE insulated, armoured, heavy duty elecric cable with alluminium conductor, 1100 volt grade cross sectional area 16 Sqmm 4 core.

Excavation in trenches not exceeding 1.5 mtrs wide & not exceeding 1.5 mtr in depth in soft or loose soil & getting out complete all as per & directed.

Returning filling including spreading levelling watering & well Ramming in layers not exc 25 cm

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed.

M & L for laying of HDPE double wall corrugated pipes in trench for UG cable protection conforming to IS-14930 Part-II with IP-67 having outer dia 50 mm and inner dia of 38 mm including necessary fittings such as couplers, bends etc complete all as specified and directed. Make: Rex/ Rudrax Polymers/Finolex

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

M/S PANCHAM RAI SONS

M/s Vikram Singh

M/S NIRBHAY KUMAR SINGH

M/S ABHAY KUMAR AND BROTHERS

M/S ASHOK KUMAR

MS HARI MOHAN GUPTA

SUDHIR KUMAR SINGH

M/s Kundu Enterprises