ADDITION AND ALTERATION OF TOILETS OF 1 STC OFFRS MESS AND SPECIAL REPAIR TO BLDG NO P-95 SANJAY KUMAR ENCLAVE OF 1TTR AND CERTAIN MINOR WORKS UNDER AGE B/R-III AT 1STC, 1TTR AND 1MTR OF GE (WEST) JABALPUR

Amount

Surfaces excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in Soft / Loose soil complete all as specified and as directed. 30+60+50

Excavation over areas not exceeding 1.50 m in depth and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plain area and not exceeding 1.5m deep in Soft / Loose soil, laying pipes, cables, as in foundations, etc. complete all as specified and as directed. 40.50+12+24+9+26.25+22

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming. 4+8+6.3+14.50+12

Excavation in post holes each not exceeding 0.5 Cu.m, getting out in Soft / Loose soil, including returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and as directed.

M & L for 50 mm thick Sand filling below the interlocking paver block including watering and consolidation complete all as specified and as directed 1+4.50

Supply and laying Sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed by Engr in charge. NOTE : Punned thickness only shall be measured and paid. 9+8

Removal of excavated material [Soil] to a distance exc 50m but not exceeding 250m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. 116.50+8+16+7.50+2.70+11.70+10

M&L for hard core of broken stone or boulder of gauge not exc 63mm, deposited, spread and level in layers not exc 15cm thick watered and rammed to a true surface complete all as specified and directed. 3+6+7+20

M & L for moorum/ red bajri filling under floors laid in layers not exceeding 15 cm thick, spread levelled and rammed / rolled including watering to required level and gradient complete all as specified and as directed. 10+2+4+7

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed. 20+1.20+2.40+1.5

M&L for PCC 1:7:12 Type F2 laid sunken floor complete all as directed and specified

M & L for PCC 1:2:4, Type B-1, using 20 mm graded stone aggregate as in Roof kerbs, Coving etc including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. 0.72+0.50

M&L PCC 1:2:4 type B-1 (using 20 mm graded stone agg) as in seismic and other similar bands, coping, bed block or similar works, and including necessary form work, etc., complete all as specified and as directed. 0.46+0.60

M&L for Providing PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate as in coping , benching/haunching , slightly rounded or chamfred angle and throating etc all as directed .

M & L for PCC 1:3:6, Type C-1, using 20mm graded aggregate as in mass concrete complete all as specified and as directed.

M&L PCC 1:3:6 type C-0 using 12.5mm graded stone aggregate as in filling of pressed steel door frame complete all as specified and directed.

M & L for RCC 1:2:4, Type B-1, using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and as directed. 2.6+6

M&L for RCC 1:2:4 (Nominal mix) type B-1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs , landings, balconies, canopies, deck slab and in shelves and the like complete all as specified and directed. 1.50+3

M & L for RCC (1:2:4) nominal Mix using 20mm graded aggregate as in chajjas,parapet facia etc complete all as specified and as directed.

M & L for RCC 1:2:4, Type B-1, using 20mm graded stone aggregate as in posts, struts, columns etc complete all as specified and as directed. 2+4

M&L for RCC -M-25 ( nominal mix) using 20mm graded stone aggregate as in Fins, fascias, louvres,parapets, and railings exc.60cm in height, newels, balustrade, and the like complete all as specified and as directed.

Supply only integral water proofing compound complete.

M & L for brick work with sub class "B" bricks straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed. 11+24+15+0.50+0.40

M&L for Brick work with sub class ‘B’ brick, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete . 8+10

M & L for brick work with sub class ‘B’ (old size) bricks, straight or curved on plan, exc 6 mtr mean radius, built in cement mortar 1:6 complete all as specified and directed.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete.

Cutting chases, pinning in, making good to facings for concealed water tubing etc. cutting exceeding 10cm but not exceeding 20cm girth on brick masonry wall complete all as specified and directed.

M&L for Cutting holes int or thourgh brick walls in exc half brick and nexc one brick in cement in mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete all as specified and directed.

M&L for Granite (of any type ) 20 to 22mm mm thick work (table rubbed and polished ) in steps ,jambs,pilllars,window cill,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2)using marble dust with admixture of pigment to match with shade of Granite laid over and including 20mm thick screed bed in CM 1:6 complete all as specified and directed.

Use and waste of form work to sides of concrete foundation, footings bases of column, raft and raft beam and similar work for rough finished surfaces complete all as specified and as directed. 30+55

Use and waste of form work to faces of walls, retaining walls , abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc, vertical or to batter surface fair finished complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including fair finished surfaces complete all as specified and directed. 12+20

Use and waste of form work to Chajjas and similar items including edges etc complete all as specified and directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns of any shape / cross section for fair finished surfaces of concrete complete all as specified and as directed. 20+35

Use & waste for form work to edges of concrete flat, treads breaks in floor, window cills, concrete railings, openings in concrete walls, floor and roof and similar work exc 10 cm but not exc 20 cm wide complete all as specified and directed. 14+24

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part -I,section 8,clause 8.24 (a) complete all as specified and as directed.fitted to chowkhats for doors etc complete.

S & F factory made 35 mm thick plain, framed, panelled shutters (Two panels) with lock rail and panel of 9 mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces and size of the members of shutter are as per IS – 1003 (Part – I) made of kiln seasoned & chemically pressure treated 2nd class hardwood rail and style complete all as specified and directed.

Taking down chowkats or frames n exc1.5 sqm with shutter (without taking off shutters from the frames). 32+4+4

Taking down chowkats or frames exc 1.50sqm but n exc 4 sqm with shutter (without taking off shutters from the frames).

Taking down aluminium window/ steel window and ventilator frames of size not exc 1.50sqm each complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails . M,S frame shall be covered with heat moulded plain colour PVC ,C, channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails , lock rails and bottom rails on either side and as gap insert for top rail and bottom rail Panelling of plain colour PVC sheet to be fitted in the M.S frame welded /sealed to the stiles & rails with suitable PVC sheet beading , and jointed together with solvent cement , complete all as specified and as directed. Make Rajshree

M & L for Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube S & F in opening complete all as specified and as directed.

M & L for Solid PVC door frame of size 95mmX50mm made out of 5mm plain colour PVC sheet reinforced with MS square tube S & F in opening complete all as specified and as directed.

S &F factory made single piece extruded solid PVC 3D wood grainmoulded door shutter 35mm (single rebate )made out of single piece extruded (SPE) solid PVC with partical baord with smooth 5 mm thick sheet of 20 mm width for style & (5 x 2) 10 mm thick 20 mm width for top & bottom rails,SPE 5 mm thick sheet both side laminated inserted as panel a as mm thick per manufacturers specification and direction of Engineer-in-Charge

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm complete all as specified and directed 32+10

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F in repair aluminium alloy anodized sliding door bolt with hasp, staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy length of bolt 300mm complete all as specified and directed by Engr-in-charge.

S & F in repairs 100 mm size, Butt hinges, Stainless Steel, Medium weight, bright polished including fixtures complete all as specified and as directed.

S&F, 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin,Type-B-21 complete all as specified and as directed.

S&F 300mm long mild steel ordinary rat tail rod pattern springs,including roller and roller plate complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed. 56+10

S&F extruded aluminium alloy handles, fabricated type, anodised of size 125 mm complete all as specified and directed.

S&F aluminium hat & coat hooks solid body 125 mm to 175 mm fixed with brass screw complete all as specified and directed.

S & F in repairs Hasp and Staple, safety type of aluminium anodised including bolt to hinge plate, fixed with screws of 125mm size complete all as specified and as directed.

S & F in repairs Towel rail 600 mm long and 20 mm dia brass chromium plated D type fixed with screws and wooden or plastic cleats complete all as specified and directed.

S & F in repairs Floor Door Stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed. 16+4

S&F galvanised MS wire cloth, 0.56mm nominal dia of wire average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 250+50

S&F hand rails, half rounded or other stock section or core for wooden hand rail straight portion, drilled and counter sunk for balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc; flat iron fillets (for securing wire mesh etc,) including all necessary drilling bolting or riveting, etc and similar work conforming to Fe410-0 or Fe 310-0 complete all as specified and directed.

M&L reinforcement using TMT steel bars of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 280+440+10

S & F reinforcement using TMT steel bars of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 280+485+45

S & F reinforcement using TMT steel bars of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed. 135+252

S & F rolled mild steel sections of grade Fe - 410 - S as in main and cross beams, hip and jack rafters, purlins where connected to common rafters, fixed with angle cleats etc complete all as specified and as directed.

S & F mild steel plate (plain or chequered) channels,square cut or notched (ordinary and counter sunk ) forming holes, with riveted,bolted or weleded attachement confirming to Fe- 290 (Gde E-165) complete all as specified and directed.

S & F of rolled mild steel work as in tubular trusses, posts etc including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS - 1161, Grade YST - 240, medium grade of any dia complete all as specified and as directed.

S&F Expanded metal not exc 4 kg/Sqm, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified and directed.

S&F pressed steel door frame of 105x60 mm with one or more rebated incl necessary fixing lugs hings, lock strick , etc complete, as specified and directed.

Pressed steel frames for doors frame of size 125x60 with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed.

S & F Aluminium anodised door, window,ventilator frame Powder Coating (minimum thickness of powder coating 50 micron) with one or more rebates and shutter incl jointing cleat for fixing etc. including making good to the disturbed surfaces and matching existing treatment (cemnt base paint/distemper/white wash/plastic paint) etc complete, as spd .

S&F, Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified

S&F, Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified

M&L for wire brushing and cleaning top surface of tiles,lime terracing or cement concrete,including flashing and junction of parapet,etc,and surface painting with a layer of blown bitumen of any penetration applied hot @1.70 kg per sqm.blinded with grit or pea size gravel @ 0.006 cu.m per sqm and lightly tampered (area of flashing etc.shall be added to the roof area.

Bitumastic gola ,with 80/25 bitumen and coarse sand mixture ,1:3 by weight ,8cmX8cm at the junction of roofing to vertical surface.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3

Taking down eaves gutters and rainwater pipes (any size or pattern ),including all fittings,heads,shoes,bends,swan necks etc.including cleaning or refixing or removal to store. 50+24

M&L for 9 mm thick prelaminated particle board interior grade,prelaminated both sides with decorative choice laminaions fixed with screw to timber/steel frame work as in repair all as specified

M&L for 18/19 mm thick prelaminated particle board interior grade,prelaminated both sides with decorative choice laminaions fixed with screw to timber/steel frame work as in repair all as specified

M&L for machine cut Kota stone slab flooring, 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing (granite finish) and exposed edges of Kota stone shall be rounded including 20mm thick screed bed to floor finishes in cm 1:6 complete all as specified and directed.

M&L 18 to 20 mm thick machine cut kota stone as in vertical surfaces risers of steps , skirting, dado and pillars etc set and jointed in neat cement slurry and pointed with grey cement mixed with pigment to match the colour of stone slab laid over and including 10 mm thick rendering in cement mortar 1:4 including rubbing and mirror polishing complete all as specified.

M&L for 18-20mm thick black granite stone slab machine cut in skirting/dado, cooking platform, jams, pillars, windows cills and the like laid over and including 15mm thick screed bed or backing coat in cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

Machine cut Cudappha stone slab on cooking platform/shelf 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L for rounding to edges of granite stone slabs one edge such as in counter type WHB platform etc. to the entire satsfaction of Engineer-in-Charge..

Rounding to edges of stone slabs one edge, such as window cills fixed with CM 1:4 and similar situations complete all as specified and directed.

M & L for 50 mm thick PCC 1:2:4, Type B-2, using 40mm graded aggregate as in plinth protection all as specified and as directed. 15+30

M&L 75 mm thick PCC 1:3:6 type C-2 using 40mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete.

M&L 75 mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded stone agg as in sub base finishing the surface even and rough to receive floor finishes complete all as specified and directed. 16+30

M&L 100 mm thick plain cement concrete 1:4:8 type D-2 (using 40mm graded stone agg as in sub base finishing the surface even and rough to receive floor finishes complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in sub base to receive floor finishes complete all as specified and directed. 94+249

M & L for 40 mm thick PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in Flooring, surface finished even and smooth without using extra cement complete all as specified and as directed. 16+30

Roughening surfaces of old concrete floor/terrace by picking incl. taking down existing detoriated / decayed tar felt PCC tiles or any type of treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 50 m.

M & L for glazed ceramic tiles, coloured, first quality, of size 350x250x7mm / 450x350x7mm thick as in vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry, finished with flush pointing in white cement or coloured cement to match, and including over 10mm thick CM 1:4 on fair faces of brick work or concrete surfaces as backing for tiles, etc., complete all as specified and as directed. 17.50+140+188

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM 1:6 complete as specified and directed. 40+24+94

M&L, Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or rectangular) area of Each tile exc 0.18 Sqm but not exceeding 0.36 Sqm, as in skirting ,dados in vertical surfaces etc and including 10mm thick cement plaster 1:4 complete all as specified and directed.

S&F cement concrete tiles size 25cmx25cmx22mm thick machine cut pressed set jointed and pointed in neat cement slurry with grey cement and pigments in floors and cut and polished complete all as specified and directed

M&L for 60mm thick, M 35 grade, Machine pressed precast concrete interlocking paver block of any shape and size with grey cement and pigment, confirming to IS 15658-2006, complete all as specified and as directed. 200+10

Dismantaling floor hearth or wall tiling/china moisac including cement mortar bedding (but not backing ) , removing serviceable tiles to store and rubbish off the premises complete all as specified. 171+282

M&L for Bitumen blown any grade , applied hot, two coats to concrete surfaces at the rate of 1.5Kg sqm per coat. Including polythene film, black , 50 micron laid in floors.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:6, mixed with water proofing compound as per manufacturer's instructions, surfaces finished even and smooth without using extra cement complete all as specified and as directed. NOTE : Water proofing compound shall be measured and paid separately under respective item of BOQ.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, mixed with water proofing compound as per manufacturer's instructions, surfaces finished even and smooth without using extra cement complete all as specified and as directed. NOTE : Water proofing compound shall be measured and paid separately under respective item of BOQ. 300+10+10

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces ceiling etc and finished even and smooth without using extra cement complete all as specified and as directed. 10.50+21+150

M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound @ 3 % by weight of cement on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed.

(a) Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster.

(b) One coat of hot blown bitumen of grade 85/25 @ 1.2kg /sqm shall be applied over primed surfaces.

(c) One layer of APP based polymeric water proofing membrane of weight not less than 3 kg/Sqm consisting 3mm thick reinforced with polyster non wove fabric shall be unrolled surfaces with lap of 100 mm and the over lap shall be sealed by flame.

(d) Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm.

M&L for 20mm thick Screed bed or bedding layer of cement mortar 1:4 .

M&L for preparing of new plastered or un-plastered wall surfaces and applying two coats of oil bound distemper over and including 3 mm wall putty on plastered surfaces, preparatory to distempering complete all as specified and directed. 20+200

Taking down Cement Plaster any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. 650+10

M & L for preparation of newly plastered wall surfaces and applying two coats of cement based paint over a coat of primer complete all as specified and as directed. 40+65+300

M & L for preparing newly plastered wall surfaces and applying three coats of white washing complete all as specified and as directed. 25+40

M&L for complete removal of existing treatment & washing rubbing down and stopping of distempered and painted surfaces incl preparation of old undecorated surface of walls and applying two coats of cement base paint on external wall Priming plastered and other surfaces with alkali resistant priming paint complete all as specified and directed. Note:- Curing shall be done before and after applying of paint.

M&L for complete removal of existing treatment & washing rubbing down and stopping of distempered and painted surfaces incl preparation of old undecorated surface of walls and applying two coats of oil bound distempered over 2mm thick wall care putty on wall over priming surafce complete all as specified and directed

M & L for preparing newly plastered ceiling surfaces and applying three coats of white washing complete all as specified and as directed. 10.50+21+150

M&L for Prepration of old surfaces of ceiling includinng scrapping down smoke ,soot,and efflorescent salts and treatings oil and gresy spots, brooming down or steel wire brushing removing nails making good holes cracks etc on plastered or unplastered surfaces and applying one coat of white wash on ceiling surface complete all as specified

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S&F, 5 mm thick, black frosted glass with nano coating fixed to aluminium doors/windows/vents with necessary rubber gaskets complete all as specified and directed.

S&F 4mm thick figured glass, pinn headed type and glazing with oil putty in square n. exc 0.5 sqm Each panes complete all as specified

M&L for Prepration of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint of (white or tinted) complete all as specified.

M&L for Preparation of newly wooden surface of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of pink primer com all as specified.

M&L for treating small article such as stops, covers, gully, gratings and hold fast ends & post backs of chowkat etc with creosote oil, tarred area n exc 0.10 Sqm Each

M&L two coat of synthetic enamel paint over new steel surface of any description over 10cm in width or grith not otherwise described over one coat red oxzide primer incl preparation of surfaces complete. 35+50+10

M&L for Prepration of old painted surfaces of steel of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint all as specified

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed for the following bores of pipe:-

(d) 40mm dia

Taking up or down steel tubing and connections complete all as specified and directed for the following bores of pipe:-

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) complete all as specified and directed for the following bores of pipe:-

S&F, in repair, 32mm bore, low density polyethelene pipe (LDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed. 10+8

Dismantling water tanks exc250 and n exc 500 ltr capacity complete all as specified and directed.

S& F 500 ltrs capacity rotational moulded polyethylene water storage tanks( cylinder vertical with closed top) hoisted and fixed in position incl neccesaary nipple and fixing arrangements all as specified in SSR Part-I complete all as specified and directed.

S& F in repairs 15 mm bore bib tap cast copper alloy, chromium plated, long body fancy type with capstan headed, screwed down, screwed for iron pipe complete all as specified and directed.

S&F fancy type pillar tap, cast copper alloy with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore.

S&F, in repair, Angular stop valves,, fancy type, chromium plated with long shank and cup, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore with flange Make Jaquar Cat part No OPP CHR 15053PM complete all as specified and directed.

S&F, in repair, stop valves (Concealed type) cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore with flange Make Jaquar/Cera or equivalent complete all as specified and directed.

S& F in repairs Stop valve / Angle valve fancy type cast copper alloy chromium plated screwed down high pressure with capstan heads screwed both ends for iron pipe or for union and fixed 15mm bore complete all as specified and directed.

S&F 20mm dia gun metal,globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed

S&F 25mm dia gun metal,globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed

S&F CP waste fittings brass chromium plated for sink 32mm dia with long screws sinks and fly nuts , flenge end bedded in red led cement and other in fixed all as specified and directed.

S&F CP waste fittings brass chromium plated for sink 40mm dia with long screws sinks and fly nuts , flenge end bedded in red led cement and other in fixed all as specified and directed.

S & F 20mm bore ball valve high pressure PTMT with epoxy coated aluminium rod & high densitypolythene float ball and fly nut screwed for iron pipe complete all as specified.

S&F in repairs grating doom 100mm dia PTMT with waste hole (Min weight 25 grms)

S&F in repairs grating doom 125mm dia PTMT with waste hole (Min weight 40 grms)

S&F in repair PVC connection 450 mm long, 15mm size with PTMT nuts complete all as specified 20+4

S & F stack clamps out of 50mm by 5mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore etc all as specified.

S&F 110 mm dia PVC (SWR ) pipes Single socketed in any length with rubber rings ljoits fixed to walls complete all as specified and as directed. 25+12

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floor/ trenches or fixed to wall with necessary clamps complete all as specified. 25+12

S&F 110 mm dia PVC (SWR ) bends any radius with access door complete all as specified and as directed. 8+5

S&F 75 mm dia PVC (SWR ) bends any radius with access door complete all as specified and as directed. 8+5

S&F PVC (SWR) plain bend any radius for 75 mm bore complete all as specified and directed.

S&F PVC (SWR) plain bend any radius for 110mm bore complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (equal or un equal) , ordinary or inverted (spigot or socket type) or with parralled branches of 110 mm dia with access door

S&F 110 mm dia PVC (SWR ) branches piece,double (double Y) equal or unequal with access doorrubber rings ljoits fixed to walls complete all as specified and as directed.

M/L PVC(SWR) Tee of 110mm dia with access door etc complete all as specified and directed

M/L PVC(SWR) Tee of 75mm dia access door etc complete all as specified and directed

S&F, reducer 75mm bore PVC (SWR) complete all as specified and directed.

S&F, reducer 100mm bore PVC (SWR) complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl including jointing with solvent cement complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl including jointing with solvent cement complete all as specified and directed. 4+4

M&L for 100mm dia cast iron floor trap plain with grating including jointing and fixed with cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair, cast iron nahani trap, with chromium plated grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4), dia of outlet 100mm complete all as specified and directed.

M&L for 75mm diaPTMT multi floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) gully trap 125 x 110 mm setting and jointing with solvent cement complete all as specified

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 150mm bore of pipe complete all as specified and directed.

M&L, in repair, salt glazed stoneware gully traps square or round mounthed, type 'P' of size 125 x 100mm, setting and jointing with cement mortar (1:1) complete all as specified and directed.

S& F in repairs Vitreous China wash hand basin, white, flat back, size 550mm x 400mm including brass coupling, mild steel brackets fixed to wall, with pedestal complete all as specified and directed.

S& F in repairs chromium plated shower rose 125 mm size and 15mm dia with or without swivel joints including fixing to pipe and union complete all as specified and directed

S& F in repairs chromium plated shower rose 300mm x300mm size and 15mm dia with or with square shape single flow (high flow ) including fixing to pipe and union complete As per Cat No OHS CHR 1639 and SHA CHR 455L600 (shower arms ) of Make : Jaquar all as specified and directed

S&F, in repair, chromium plated, Toilet paper holder complete all as specified and directed. As per Cat No ACN -1153N of Make : Jaquar or equivalent as approved by GE from the makes mentioned in Appx 'C'.

S&F Soap dispenser automatic capacity 0.8 ltr material AISI aluminium/ABS (Absolute Butadin steren Jaquar Cat Part No HDR SDR BLC DJ0160AT pecified and direcrted Make : 3 or equivalent as approved by GE.

S&F in repair tumbler holder as per Cat No ACN -1141N of Make Jaquar or equivalent Make as approved by GE from Appendix 'C'.

S&F in repair Towel ring round with round flange complete . As per Cat No ACN-1121BN of Make Jaquar or equivalent Make as approved by GE from Appendix 'C'.

S&F, in repair, CP, soap dish holder complete all as specified and directed. Make : Jaquar Cat No - ACN-1131N or equivalent as approved by GE.

S&F in repair glass corner complete all as specified and direcrted Make : Cera Cat Part No CA 503 or equivalent as approved by GE.

S&F, in repairs, brass, chromium plated tubular towel rack 20mm dia 60cm long between flanges Make : Jaquar Cat No ACN CHR 1181S or equivalent as specified and directed.

S&F, in repair, glass shelf with CP brackets and with decorative railing fixed to wall complete all as specified and directed. As per Cat No ACN -1173 of Make : Jaquar or equivalent as approved by GE.

M&L for 150mm bore, reinforced concrete pipes, class NP-2, laid and jointed complete with collars all as specified and directed.

S&F in repair vitreous China squatting pan of pattern Orissa Pan , size 580 x440 mm white with integral foot rests any pattertn (excl flushing cistern and flush pipe) complete incl provn of lime concrete bedding connection to flush pipe , trap etc & making good.

S&F in repairs 10 ltr PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle with flush pipe complete all as spfd

Soap dish, stainless steel approx size 160mm x 160mm x 90mm complete all as specified and directed.

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cab les ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 2.0 core 10 Sqmm complete all as specified and directed by Engineer in charge Make- Polycare,Havals

Supply and laying Brick covering with width equal to length of brick as mechanical protection to cable with well burnt sub class ‘B’ bricks laid dry flat complete all as specified and directed by Engr in charge. 892.50+800

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. 0.40+2

Demolition of Unreinforced Cement Concrete in ground floors and Pavings exceeding 15cm thick [below or above ground level] complete all as specified and as directed. 11.15+2.35

M/L for Demolition of road/path /concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) .complete all as specified and as directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including reinforcement cut as required to facilliate demolition complete all as specified and directed.

Demolition of Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition and breaking up drain pipes (slat glazed stoneware, AC or RCC) set in cement mortar for 150mm bore of pipe complete all as specified and directed.

M&L for complete removal of existing treatment on walls including steel wire brushing and scraping etc and applying two coats of exterior emulsion paint over 2mm thick( Avg) Birla wall care putty in two layers on wall surfaces including rubbing, levelling and preparing the surfaces for receiving further finishes as directed.

M&L for 15mm thick plaster in CM 1:3 in two layers,with & including wire netting of galvanized steel wire 0.91mm dia and mesh size 12mm placed in walls before plaster layers and fixed with tinned tack or wire stapled where required first layer of 10mm thick plaster in cement mortar 1:4 & second layer of 5mm thick in cement mortar 1:3 including taking down of loose /bulsing surafces of plastered or concrete as in chajjas, beam balcony fins etc to make to original shape at any height to repair chajjas, beam balcony fins etc in multistoreyed buildings, top layer of plaster finished even & smooth without using extra cement complete including cleaning and preparation of existing RCC surfaces and applying a coat of cement slurry and surface shall be match & finish the existing surface by applying two or more coats of cement base paint/ anti fungal exterior emulsion paint complete all as specified and directed. Note : Each layer of plaster shall be done separately.

Supplying and fixing pre painted steel sliding window 3- track,2 glass panel and 1 mesh panel sliding windowfabricated from roll formed sections made of galvanised steel clolour powder coated ( Base steel as per IS 513 'D' quality,galvanised as per IS 277 with zinc of 20 GM/Sqm) with total coated thickness of 0.58mm. primer coated with epoxy coated of 5-7 micron thick, finish painted with a polyster paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyster powder up to 50-60 microns thick.Section of mesh should be of 35x49mm.The window should be paneled with 5mm thick plain float glass.Corner bracked for internal and external frame made of glass filled nylon.Gasket are to be made of Ethyl Propylene Diamine Monomer (EPDM). THe sections are to be cut to length,joined and assembled by means of of corner bracket.The above frames should be fixed to concrete/masonry wall by means of self expanding screw.

S&F stainless steel hydrolic soft close auto hinges size zero degree incl necessery fittings complete all as specified and directed.

S&F MS Peg set of six powder coated as approved by GE

M&L for mild steel pipe 25 mm dia Drapery rod fancy type with PVC coating fixed in the MS hooks, and finials/side brackets (both side), shade as approved by GE all as specified.

S&F in repair C P glass corner shelf set of three single including Screws and CP bracket complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guards and railing 600 mm long complete all as specified.Make- Jaquar Cat Part No- AKP 35715PS

S&F in repairs kitchen plate rack made of stainless steel 1mm thick complete size 1200 x 900mm x 200mm width of trade pattern complete all as specified.

S & F in repairs Towel ring brass chromium plated round type fixed with screws and wooden or plastic cleats complete all as specified and directed.

S&F, in repair, for 5 mm thick ACP Aluminium composite pannel board prelaminated both sides with decorative choice laminations and fixed with screws to aluminium frame work complete all as specified and directed.

S&F, in repairs, 18mm thick, PVC sheet one side prelaminated of approved texture ("Celuca Ply of Rajshree make or equivalent in "Sintex" as approved by GE) as in Kitchen cabinet (with shelves and partitions) including necessary fittings & fixtures as per manufacturer's instructions complete all as specified and directed.

S&F, in repair, vitreous china rimiless wall hang WC with UF soft close seat cover , hinges accessories set as per Make Jaquar cat Part No DRS WHT 37951 BIU FSM (including fixing bolts but excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F, in repair, single piece slim concelaed flusing cistern, with wall mounted frame installation kit and S type drain pipe connection set for wall hung WC with flush control plate) as per cat Make Jaquar part No JCS WHT2400FS and control plate JCP CHR 852415 complete all as specified and directed.

S&F, in repair, vitreous china floor mounted WC with PP soft close seat cover , hinges accessories set as per Make Jaquar cat Part No ARS WHT 39751P size 375x660x800mm with cistern fitting for 39751P (including fixing bolts flush pipe) complete all as specified and directed.

S&F, in repair, vitreous china full padestal wall hung basin white with fixing accessories of size 610 mmx 480mm X 1950mm , counter top basin, grouted in cement mortar 1:2 complete all as specified and directed. As per Cat No. FNS WHT 40801 and FNS WHT 40301 of make Jaquar or equivalent as approved by GE from the make mentioned in Appx 'C' Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

Supply & fixing 32mm, waste fittings, brass chromium plated for glazed ware sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed as per Make Jaquar cat Part No ALD CHR 705L 130 complete all as specified and directed.

S & F PVC waste pipe 32mm bore of size 750mm to 900mm long complete all as specified and directed.

S&F in repair 8mm dia brass, chromium plated health faucet (Hand shower) with 01 meter long flexible tube and wall hook. Make : Jaquar Cat No - ALD-573 or equivalent as approved by GE, complete all as specified and directed.

S&F in repairs, hand shower sizes 65x95mm rectangular shape singel flow with rubite cleaning system face plate stainless steel and ABS body in chrome finished ) with 1.5 meter long flexible tube with nut and premium wall braket for hand shower 35mm dia and 100mm long round shape complete all as specified and directed. Make : Jaquar or equivlanet (Code No. HSH CHR 1729 , CHR 549D12 AND SHA CHR 555ALD-CHR-555).

S&F, in repair, basin mixture single lever tall boy with 155mm extension body fixed spout without popup waste system with 600mm long braided hoses of 15mm bore complete all as specified and directed. Make : Jaquar (Cat No. OPPCHR 15005BPM ) or equivalent as approved by GE.

S&F, in repair, two way bib cock fancy type, chromium plated with high pressure, of 15mm bore with flange Make Jaquar Cat part No OPP CHR 15041PM for WC point complete all as specified and directed.

S&F in repairs, brass chromium plated single lever consealed diverter mixer 3 in 1 system with provision of both over head shower and hand shower with 115 mm long bend pipe connecting legs and wall flange (without hand and over head shower Make - Cat No. OPPCHR 15079KPM , ALDCHR 079 body of canceled diverter and bath tab spout cat part No SPJ CHR 15463PM of Jaquar or equivalent complete all as specifed and directed.

S&F, in repair, PVC Bath Cabinet made from hard thermosetting material with mirror, white/ivory colour, 400 x 500mm size. As per Cat No. 554 of Make Prayag or equivalent Make as approved by GE from Appendix 'C'.

M&L for refixing of false ceiling any type complete as specified and directed.

M&L for refixing of old any type of wall mixture, hand shower & bib tab any type complete as specified and directed.

S&F, in repair, jet spray with 1m PVC tube (stainless steel), chromium plated for vitreous china padestal pattern water closet complete all as specified and directed. Make-Jaquar Essco(Cat No - ALE -547) or equivalent as approved by GE.

S&F, swiel mirror 500 round As per Cat No CAN CHR -1195N of Make : Jaquar complete all as specified and directed. Complete all as specified and directed.

S&F,Double arms wall mounted revsersible plain and magnigying (X3) pivotal mirror size 232mm round As per Cat No CAN CHR -1193N of Make : Jaquar complete all as specified and directed.

S&F Shower panel black stainless steel structure 2 adjustable vertical jet sqaure round, integrated shower head 8" round with thermostatic mixture with brass spout and minimum water pressure 2 bar size 1800x200mm with anti finger print stainless steel body ABS movable top shower thermostatic mixture diverter brass spout hand shower , two movable ABS body massa shower Make - Cat No. JPL SSF ST-8896 of Jaquar or equivalent complete all as specifed and directed.

Taking down carefully any type point wiring (light, fan, socket bell or power) , complete with fitting such as switches ceiling roses,lamp holders sockets,regulators,call bell light fitting with PVC conduit surface /concealed or wooden pattens including sunken cast iron /pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces all as specified and as directed 196+36

Taking down carefully Main switch and Distribution boards any make and size .

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface all as specified and directed at site.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Taking down the ceiling fan in situ and refixing after servicing, repairing and painting to ceiling fan including scratching old paint and preparation of surface for painting with one coat of white/grey enameled paint complete all as specified and directed.

Taking down carefully Old unserviceable any type sub main wiring with wooden batten/PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed by Engineer in charge.

M/L for Sub Main Wiring two single core PVC insulated cable FRLSH of size 6.0 Sqmm multistranded copper conductor two run drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting,fixing accessories and one run of 6.0 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :-Two Nos of 6.0 Sqmm Wire and one No of 6.0 Sqmm Earth wire in One RM length Measured as one unit length.

M/L for Sub Main Wiring with two single core PVC insulated cable FRLSH of size 4.0 Sqmm multistranded copper conductor drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting,fixing accessories and 2.5 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :- Two run of 4.00 Sqmm Wire and One run of 2.5 Sqmm Earth wire in One RM length Measured as one unit length.

M/L for Sub Main Wiring with Two single core PVC insulated FRLSH cable of size 4.0 Sqmm multistranded copper conductor drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting,fixing accessories and 4.0 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :- Two run of 4.0 Sqmm Wire and One run of 4.0 Sqmm Earth wire and rigid non metallic PVC conduit in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed/open PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of antirorrrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engineer in charge.

(a) One light point/Bell point/exhaust fan point controlled by one switch. 4+88+16

(b) One fan point controlled by one switch.

(c) One socket point controlled by one switch on same board. 24+8

(d) One socket point controlled by one switch on Independent board. 2+24+8

Description all as per item No 7 here in befor but with 1100 volts grade copper standard conductor cable FRLSH of size 2.5 Sqmm with 2.5 Sqmm solid copper conductor PVC for 3 pin switch socket outlet15 Amp independent board complete all as specified and directed by Engineer in charge . 12+4

S & F in repair for bell ding dong AC 230 volts single pole one way complete all as specified and directed by Engineer in charge. Make: anchor/plaza/leader

S & F in repair for Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge. Make : Anchor/Plaza/Leader 6+184

Supply & Fixing Modular Switches 5 /6 AMPS with fixing arrangements all as required and directed Make:anchor/plaza/leader

Supply & Fixing Modular Switches 15 /16 AMPS with fixing arrangements all as required and directed Make:anchor/plaza/leader

Supply & Fixing Modular Sockets 6 amps 3/5 pin with fixing arrangements all as required and directed Make:anchor/plaza/leader

Supply & Fixing Modular Sockets 15/16 amps 5/6 pin with fixing arrangements all as required and directed Make:anchor/plaza/leader

S & F in repair fan regulator Step type of polycarbonate complete all as specified and directed .Make: anchor/plaza/leader

S & F in repair for Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed 2+48

S & F in repair for switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and directed Make: anchor/plaza/leader

S & F in repair lamp holder PVC Polycarbonate type body, with back plate for batten fitting icluding 9 watt led lamp complete all as specified and as directed by Engineer in charge. Make: anchor/plaza/leader

S & F in repair for Ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and directed by Engineer in charge 4+48

M/L for Ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and directed by Engineer in charge Make- Anchor, Plzaa, Leader.

S & F in repair Smart bright Batten Series, LED luminaire using LEDs 20 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as directed.Make : Philips Cat part BN 021 LED 22S 6500 PSU GR SI or equivalent in Havells/Bajaj.

S & F in repair Smart bright Batten Series, LED luminaire using LEDs 22 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as directed.Make : Philips Cat part BN 021 LED 22S 6500 PSU GR SI or equivalent in Havells/Bajaj. 24+4

S & F in repair of LED Decorative /mirror light fitting 9/10 watt along with fixture Surface mounted suitable for indoor aplication , connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge.Make- Havells LUMILINEPLUSSBS10WLED865SPCSS or equivalent in PHILIPS ,BAJAJ 8+4

S & F in repair Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suiyable size & length complete all as specified & directed. Make :Havells Cat Part No. HEXAFT10WLED857SSYMBOPC or Equivalent make Philips / BAJAJ

Supply & fix in replacement of LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.Make:Havells cat part no: LHDAUU7PA7J025 or equivalent in philips or bajaj

S & F Exhaust fan heavy duty size sweep 300 mm sweep, 230 v, 50 Hz , complete with louvers including making holes and making good the disturbed surface complete all as specified and directed by Engineer in-charge. Make:Bajaj/havells 8+4

Supply and fixing in replacement of decorative wall light fitting WITH LAMPS 9 WATT made up of Polycarbonate , City-1 , Cylindrical shape , with LED lamp 9 Watt complete with fixing arrangements on wall all as specified and directed.Make:City 1 of Havells or equivalent in bajaj/philips

S & F in repair Sheet metal enclosure DBs Single Pole and Neutral 4 way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed.Make: Legrand cat no :5078 11 or eq in SEIMENS /GE

S & F for single pole and neutral enclosure with a two pin and earth plug and socket complete suitable for 240 volt 50 Hz AC supply three pin with single pole MCB 20 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed.Make: Legrand cat no :5078 11 or eq in SEIMENS /GE

S & F in repair Sheet metal enclosure DBs Single Pole and Neutral 8 way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge. Make: Legrand cat no :5076 21 or eq in SEIMENS /GE

S & F Sheet metal enclosure DBs Single Pole and Neutral 4 way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge.

S & F in repair MCB TPN 415 volts 63 Amps, C Series complete all as specified and directed by Engineer in charge Make: Legrand cat no :4086 83 or eq in SEIMENS /GE .

S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.Make: Legrand cat no :4086 83 or eq in SEIMENS /GE

S & F in repair Sheet metal enclosure DBs Tripple Pole and Neutral 4- way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge Make:Legrand Cat no :5077 80 or Eq in SEIMENS/GE .

S & F for sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. Make:Legrand Cat no :5077 80 or Eq in SEIMENS/GE

Supply and fixing in replacement MCB single pole 240 volts upto 40 Amps, B Series complete all as specified and directed by Engineer in charge Make- Legrand , L&T, ABB. 1+24

S & F MCB in replacement MCB single pole and neutral 240 volts to 40 Amps, C Series complete all as specified and directed by Engineer in charge. Make: Legrand cat no :5076 20 or eq in SEIMENS /GE

S & F for MCB Single pole rated capacity 5 to 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed. Make: Legrand cat no :4086 90/92/93/94/95/96 or eq in SEIMENS /GE

Supply and fixing in replacement MCB/Isolators single pole 240 volts upto 40 Amps, B Series complete all as specified and directed by Engineer in charge

Supply and fixing in replacement MCB single pole and neutral 240 volts 40 Amps, C Series complete all as specified and directed by Engineer in charge Make: Legrand cat no :4086 18 or eq in SEIMENS /GE

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipeand including GI Pipe 15 mm with bib tap etc all as specified and directed by Engineer in-charge.. Make: bajaj/havells/racold

S & F in repair for bell push piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

Supply & fixing electronic energy meter tamper proof design digital technology of SINGLE phase 1 x 240 volts 50 HZ 0.4% basic current for direct connected meter and 0.2% of basic current for CT operated meter with LCD display class-1 accuracy as per IS : 13779 Microprocessor based single phase energy meter of 10--60 Amp complete with all accessories complete with fixing accessories on finished wooden box all as specified & directed at site. Make: Saral of secure or equivalent.

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire complete with all as required and directed at site by eng in charge .Make:Bajaj/havells

Supply and fixing Single phase wall mounted remote controlled fan heavy duty AC 230 volts 400 mm sweep, metallic body complete including electric connection with twin core copper wire for wall mounted fan, nut, clamp & bolt etc complete all as specified and as directed.Make: Havells\bajaj/usha

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 3.5 core 35 Sqmm complete all as specified and directed by Engineer in charge. Make- Polycare,Havals

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) Reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing. 1+4+4

31.Supply, fixing and connecting 100 LED flood light , Energy saving and environmental friendly long life LED flood light made up of pressure die cast aluminium housing with high power LED as lighting source , with IP66 and IK 08 protection and impact resistance complete all as specified and directed.Make: Havells/philips/Luker

ANAMIKA CONSTRUCTION

mandeka constructions

TRISHLA CONSTRUCTIONS