SPECIAL REPAIR TO BLDG NO MES 96 MD OFFR ACCN AT SE FALLS ADDN ALTN TO DRAINAGE AND LOW LAYING APPROACH PATH IN FRONT OF SP 43 A AND B OR ACCN AT SE FALLS PROVN OF FALSE CEILING IN PASSAGE CORRIDOR AT OFFICE HQ CWE SHILLONG AT SE FALLS UNDER GE SHILL

Amount

Dismantling of plain or corrugated AC/ steel /fibre glass reinforced transluscent sheeting any guage thickness including nainital or similar pattern roof covering, complete, all as directed.

Dismantling boarding any description fixed in any position with nails complete, all as directed.

Dismantling of timber fillets, rails, posts, rafters, purlins, etc under 40 sqcm in section in any position (framed work) complete, all as directed.

Dismantling of wall/ceiling boards (fibre, pulp,insulation, etc.) or insulation boards/ slab/blankets, any thickness including cover filletscomplete, all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete, all as directed.

Dismantling water tank and removing to store tank of capacity 500ltr complete, all as directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below/above ground level) complete, all as directed.

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key, scrubbing down with water, etc., complete, all as directed.

Taking up or down steel tubing and connections for 15 mm bore of pipes complete, all as directed.

Taking up or down steel tubing and connections for 20 mm bore of pipes complete, all as directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm each complete, all as directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area but nexc 1.5 sqm each complete, all as directed.

Taking down shutters of any description exc 1.0 sqm but n. exc 2.0 sqm each complete, all as directed.

Taking down shutters of any description exc 1.0 Sqm and nexc 2 sqm refixing in same opening complete, all as directed.

S&F 2nd class hard wood plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 35 mm thick 2nd class hard wood plain framed panneled shutter any number of panels with panel of 9mmB.W.P. commerical play flat on both side with feather edged complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted without and mitred beads for securing glass or gauge etc all as specified in SSR Pt 1sec-8.24(a) complete all as specified and directed.

S&F pre laminated solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam single piece extruded pvc profile and edgs will be painted to match with prelam sheet , PVC sheet are to be reinforced with 19x19mm MS square tube EPDM rubber gasket weather seal shall be provided through out the frame. The profile shall be mitre cut at two corners and joint by insrting 2 nos of 150mm long backets of 15mmx15mm MS square tube inside the 19mmx19mm MS square tube and suitably screwed and fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made pre laminated solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part I, complete all as specified and directed.

M&L for 2nd class hard wood plain fillets bullnosed, splayed, chamfered or rounded on one edge or face in section clean sawn, fixed with screws sec are exc. 6 & n. exc. 13 sqcm complete all as specified and directed

M&L plain fillets square rectangular or triangular in section clean sawn secured with nails or brads (2nd class hard wood) sectional area exc 13 sqm n exc 25 sqcm all as specified complete all as specified and directed.

S&F 20mm thick 2nd class hard wood boarding in eaves board/fascia plained one side with butt joints fixed with nails complete all as specified and directed.

M&L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination as in kitchen cabinet/cup-board complete all as specified and directed.

S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as in roof covering of tensile strength 550 mpa including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed

S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick as in roof covering of tensile strength 550 mpa including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed.

M&L non asbestos fibre cement building boards of 4mm thick fixed or laid/ inserted to timber frame work fixed in jointless finish with jointing compound and jointing tape as per manufacturer instructions complete all as specified and as specified.

S&F Continuous (Piano) hinges, brass, width of flaps 30 mm (when open) complete all as specified and directed.

S&F Magnet catches for cupboard shutter, brass body and striking plate including letting in complete all as specified and directed.

S&F Extruded brass handles, 100 mm size, fabricated type, polished complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick screedbed in CM 1:3 complete all as specified and as directed.

M&L for Non skid light shade, joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for Glazed ceramic coloured tiles in vertical surface of size 450 x 300 x 7mm/300x600x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the tile colour over 10mm thick backing coat in CM 1:3 complete as specified and directed

M & LGranite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 20mm thick screedbed in CM 1:4 complete all as specified and directed.

M & L marbel of green shade other than white and black ,18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marbel shade including 20mm thick screedbed in CM 1:4 complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in path, plinth protection, sub-floors etc finished even and fair or even and rough as reqd complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in surface channel and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc., complete all as specified and directed.

Rendering 15mm thick in cement mortar 1:4 on fair faces or Brick Walls or an concrete surfacs, plastered surfaces finished even and smooth without using extra cement with WPC complete all as specified and directed. (WPC measaured seperately and paid seperately) complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) in two coats (10mm and 5mm thick) mixed with water proofing compound with 5mm thick layer on fair faces of brick work or concrete surfaces including finishing the surface even and smooth without using extra cement, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately, complete all as specified and directed.

M&L for rendering 10mm thick in CM (1:6) on fair faces of brick or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick plaster in CM (1:3) on fair faces of concrete surfaces of ceiling including finishing even & smooth without using extra cement, complete all as specified and directed.

Supply only Integral water proofing compound (WPC), ISI Mark and as approved, complete all as specified and directed.

S&F in repairs Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F in repairs in steel ventilator with top hung shutter with or without glazing bar, incl hinges, fixing lugs,steel peg stay, complete all as specified and as directed

M&L for preparation of new plastered surfaces of wall and applying two coats of Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot inted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior rimer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for preparation of new plastered surface of walls and applying two coats of acrylic distemper over a coat of alkali resistant priming paint complete all as specified and directed.

M&L for preparation of new ceiling surfaces applying two coats of distemper complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for applying two coats of White wash on ceiling including preparation of new or undecorated surface complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surface of any description n.exc 10 cm width or girth applying two coats of Synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M/L 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pan complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frame including taking out old wooden beads complete all as specified and directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty or wooden beads in squares n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 100mm complete all as specified and directed.

S&F Extruded Aluminium, anodised, bow handles of size 150mm complete all as specified and directed.

S&F aluminium anodised barrel bolts and fixed of 200 mm length complete all as specified and directed.

S&F Mild steel sliding door bolt, plate type stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, length of bolt 300mm complete all as specified and directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:- (i) Taking out old roof treatment and roughening the same old concrete slab by picking, sweeping clean and washing down with water to remove dust etc. and applying cement slurry @ 3kg/Sqm (ii) Screed bed or bedding layer of mortar 15 mm thick in CM (1:4) for laying as in roof slab with mixing of WPC and surface finished fare and smooth without using extra cement. (Note: WPC shall be measured and paid for under separate items) (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be applied by torch application over bituminous primer as specified. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying one coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm. (NOTE:- The work of water proofing treatment shall be got executed through expert team of manufacturers or authorised applicator of manufacturer contractor shall be submitted documentary evidence in support of applicator engaged for approval of GE.)

S&F in repair vitreous china wash down water closet padestral patern EWC ,white, including trap set, seat cover and conection to trap, flushing pipe, etc. complete including making good to floor fixing bolt complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type flushing cistern, low level, white, 10 Ltr capacity with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair Vitreous china WHB, white, flat back, size 550 x 400 mm including brackets, 32 mm waste coupling and 32 mm waste fittings complete all as specified and directed.

S&F GI steel tubing medium grade 15mm bore with all fitting and fixed complete to wall and ceiling or laid under in floor complete all as specified and directed.

S&F GI tubes, medium grade galvanised, 20mm bore with all fitting and fixed complete to wall and ceilings or laid in floors complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes incl bedding in CM to dwarf wall or incl fixing cantilever brackets and connecting union to pipe overall size 915x460 mm bowl size 410mmx360mmx160 mm complete all as specified and directed.

S&F in repair Bip tap, chromium plated, 15mm fancy type, ISI mark, complete all as specified and directed.

S&F in repair Angular stop cock, fancy type, chromium plated, 15 mm bore ISI mark, complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts, ISI mark, of length 450mm complete all as specified and directed.

S&F in repair 15mm bore brass CP WHB mixer for mixing hot and cold water screwed down for iron pipe and fixed. (Make - Prayag or equivalent) complete all as specified and directed.

S&F Stainless steel kitchen plate rack of size 36" X 36' X 10" made out of stainless steel sheet of 1.00 mm with all accessories including taking down old unservicable rack complete all as specified and directed. (Make : Blue star, Cat No - BSKPR-314 or equivalent model as directed by Engr-in-charge)

S&F in repairs CP over head shower dia 100mm round shape single flow (ABS body chrome plated with gray face plate) with rubit cleaning system Cat part No: OHS-1989 or equi. with CP shower arm dia 20 mm & 450 mm long round shape without bend for wall mounted showers with flange complete all as specified and directed. MAke Jaquar Cat part No: SHA-49483 or or equivalent make of Cera/Hindware/Prayag

S&F in repair CP Kitchen sink mixture fixed in poisition making good surface, complete all as specified and directed. of make Jaquar cat part no FLR 5309N or equivalent make of Cera/Hindware/Prayag

S&F in repairs CP single lever wall mixer 3-in-1 system with provision for bath hand shower & overhaed shower complete with 115 mm long bend pipe connecting legs & wall flange (without hand & ober head shower) complete all as specified and directed. of make Jaquar cat part No:OPP-15125PM or equivalent make of Cera/Hindware/Prayag

S&F in repair 15 mm bore CP health Foucet cock with Flexible pipe 1 m long complete all as specified and directed. of make Jaguar Cat Part No:ALD-565 or equivalent make of Cera/Hindware/Prayag

S&F in repairs Soap dish holder fixed in position, making good surface complete all as specified and directed. of make Prayag Cat Part No:-BA-05 or equivalent make of Cera/Hindware/Parryware

S&F in repair Toilet roll holder with stainless steel fixed in position, making good surface complete all as specified and directed. of make Jaguar Cat Part No:- AKP-35755PS or equivalent make of Cera/Hindware/Prayag

S&F in repair Towel ring sqare shape stainless steel fixed in position, making good surface complete all as specified and directed. of Make Jaguar Cat Part No:-CAN-1121N or equivalent make of Cera/Hindware/Prayag

S&F in repair corner glass shelf with bracket fixed in position, making good surface complete all as specified and directed. of make Jaguar Cat Part No:CAN-1173 or equivalent make of Cera/Hindware/Prayag

M&L for taking down of existing sunken slab treatment form the sunken portion and cleaning the surfaces by washing down with water and rubbish off the premises. (a) Cleaning and filling cracks with sealing compound, brushing neat with neat cement slurry @ 3.00 kg/ sqm and grouting in 25 mm thick plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) over sunken slab portion and finishing the top surfaces even and smooth without using extra cement . (b) M&L for two coats of acrylic cementitious water proofing coating (Dr Fixit pidifin 2K manufactured by M/s Pidilite industries Ltd or equivalent make as approved by GE) and followed by a overlay protective 15 mm thick screed/ rendering in CM 1:3 along with liquid water proofing at appropriate ratio of approved make on top surfaces of sunken slab after preparations as mentioned above. Method of application for acrylic cementitious water proofing coating is followed as per manufacturers instructions.

S&F in repair rotational moulded polyethylene 1000 ltrs capacity water storage tanks , three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball valves 20mm dia high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball including 20mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.

S&F in repairs Gun metal gate valve class I (ISI) marked with iron wheel head, screwed both ends for iron pipe, suitable for following bore of pipe including taking down old existing unserviceable gate valve of dia 20 mm complete all as specified and directed by Engr-in-Charge

S&F in repair PVC (SWR) bends, any radius, 110 mm bore complete all as specified and directed.

S&F in repairs PVC (SWR) Pipes single socketed in any length with rubber ring joints, 110 mm bore fixed to walls complete all as specified and directed.

S&F in repair PVC(SWR) pipes 75mm dia single socketed in any length with rubber ring joints fixed to walls/floor complete including clamps for securing pipe complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl 75mm dia complete all as specified and as directed.

S&F in repairs PVC (SWR) bend with access door of any radius 110mm bore complete all as specified and as directed.

S&F in repair PVC (SWR) reducer 110mm dia complete all as specified and as directed.

S&F in repair PVC (SWR) 110mm dia in junction single , (Single T) equal or unequal complete all as specified and as directed.

S&F in repair 75mm dia PVC (SWR) floor trap including jointing to pipe complete all as specified and directed.

S&F in repair for grating doom 100mm dia of PTMT (minimum weight 25gms) complete all as specified and directed.

S&F in repair 25 mm dia aluminium drapery rod with wooden finish, decorative, including brackets, decorative finials at both ends (minimum) in one opening complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed.

S&F 300mm long MS Helical door spring Welded to steel /Fixed to wooden door frame including roller and roller plate etc of approved quality complete all as specified and directed.

M&L Exterior emulsion paint ( weather coat), two coats over a coat of alkali resistant primer on external surfaces including complete removal of existing treatment over wall and preparation of surfaces even and smooth complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying two coats of Oil bound distemper, over 1 mm thick wall care putty including necessary preparation of wall surfaces complete all as specified and as directed.

M & L for preparation of old treated wooden surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for preparation of old steel surface and applying one coat of synthetic enamel paint on steel surface complete all as specified and directed

M&L for Acrylic distemper, one coat over old treated ceiling surfaces including necessary preparation of old surfaces complete all as specified and as directed.

M&L painting to new steel surfaces of any description, over 10cm in width or girth, steel Sqm surfaces in two coats of synthetic emamel paint over a coat of red-ocide primer not otherwise discribed complete all as specified and directed

S&F Anodised Aluminium frame work for snap grid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Aluminium main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mm c/c using Gi wire of 4mm thickness Aluminium frame will be 60 x 60 cm to recieve ceiling board complete all as specified and as directed .

M&L for 4mm E boards 600x600 mm prepainted fibre boards ceiling designer/decorative type with different designs as approved by the Engr-in-charge fixed or laid in ceiling timber /GI/ aluminium frame work in ceiling flat or sloping complete all as per manufacturer instruction complete all as specified and directed.

Surface excavation n. exc. 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches in n. exc. 1.5m wide and n. exc. 1.5m deep and getting out in soft/loose soil complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete and drain bed complete all as specified and directed.

M&L for precast PCC (1:3:6) type C1 (using 20mm graded agg) solid block masonry exc 10cm in width or girth and setting in CM (1:6) complete all as specified and directed.

Removal of surplus excavated soil to a distance n.exc 50 M and depositing where directed at a level n. exc. 1.5 m above starting point complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering as required complete all as specified and directed

M&L for hard core of gauge n.exc 63mm, deposited spread and leveled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for100mm thick PCC 1:4:8 type D-2 (using 40mm graded agg) as in path ,sub-base, pavings etc., complete all as specified and directed.

Returning , filling in including spreading , levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

M&L for machine pressed pre polished factory made pavement chequered cement concrete tiles of size 300 X 300 X 20 mm thick of approved design and colour , set jointed and pointed in neat cement slurry with grey cement and pigment over and including 15 mm thick screed bed in cement sand mortar (1:4) complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in parapets, coping, benching, appex stone etc water trough and the like including weathering slightly rounding or chamferred angle and throating etc including necessary formwork complete as specified and directed.

E/M Works Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, lamp holders, regulators, switch, socket outlets, bell push, ceiling rose etc., removing material to store for keeping in safe custody for reuse at site and making good to disturbed surfaces of walls with cement sand mortar (1:6) and white/colour wash to match with existing surfaces etc complete all as directed.

M&L for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20mm dia. with accessories, concealed on wall/ceiling, including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box/metal flush box with suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti-corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3mm thick plastic laminated sheet top cover for housing the switches, socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one switch. Note:- Switch, socket and fan regulators to be measured and paid for separately. PVC Conduit confirming to IS 9537 part I & III. Note (All chases will be cut by chase cutter only)

Description all as per serial item No 131 here in before but for socket outlet point 5 Amp on same board.

Description all as per serial item No 131 here in before but for socket outlet point 5 Amp on Independent board.

Description all as per serial item No 131 here in before but with FRLSH ISI marked PVC insulated and unsheathed two single core multistranded copper cable of size 4.0 sqmm for one power point, 3 pin 15 Amps on independent board including FRLSH, ISI marked PVC insulated unsheathed single core multistranded copper cable of size 4.00 sqmm green in colour as earth continuity conductor connected to common earth dolly, complete, all as specified and directed.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, flush type, one way 5 Amps complete all as specified and directed. Make: Havells/ Anchor/ Legrand

Supply and fix Switch socket combination (ISI marked), 2/3 pin and 5/16 Amps, flush type, 240 volts complete all as specified and as directed. Make: Havells/ Anchor/ Legrand

Supply and fix Socket (ISI marked), 2/3 pin and 5 Amps, flush type, 240 volts complete all as specified and as directed. Make: Havells/ Anchor/ Legrand

Supply and fix Switch socket combination (ISI marked), 2/3 pin and 5 Amps, flush type, 240 volts complete all as specified and as directed. Make: Havells/ Anchor/ Legrand

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal, poly carbonate, complete all as specified.

Supply and fixing LED batten fitting 1x 20W, 220V, AC decorative box type, warm white / white type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose pre wired fixed to wall with 2 nos PVC block of suitable size including taking down old unserviceable light fittings complete all specified and directed.

Supply and fixing LED batten fitting with all accessories 1X 10W, 6000K, extruded polycarbonate, integrated electronic driver and fixed to wall with 2 nos PVC block of suitable size including taking down old unserviceable light fittings complete all specified and directed. Make- Philips cat Part 919215850797 7-watts

S&F Exhaust fan 230 volts, 300mm, plastic body including making all electric connection complete all as specified and as directed including cutting of hole on wall and making good disturbed surface of wall and outer wooden box for fan fix on wall including taking down old one, complete all as specified and directed. Make Bajaj/Havells/CG.

Supply and fix LED lamp 7Watt B22 including taking down old one, complete all as specified and directed. Make Havell's Cat part No LHLDERUEML8X007 or equivalent make of Bajaj / Philips / Wipro

Supply and fix MCB Distribution board, 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 12 way, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, complete, all as specified and directed. Make: Havells Cat part No DHDPSHODRW12 or equivalent in Schnieder/GE/C&S.

Supply and fix in repair MCCB Distribution board, TP&N, vertical, double door, 50 Hz with IP-43 protection, sheet steel, enclosure powder coated with 200 Amps rated busbar with neutral link, 415 Volts, 4 way, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. Note 1: MCB SP/TPN shall be measured and paid separately under appropriate items of this schedule. Note 2: Copper thimble shall be used for connection of cable.

Supply and fix MCB DP, 240 Volts, 32Amps, 10 kA rupturing capacity 'C' series including taking down old one complete, all as specified and directed. Make: Havells Cat part No - DHMCCDPF006-040 or equivalent in Schnieder/GE/C&S.

Supply and fix MCB, single pole, C Series, 240 volts 6 to 32 Amps 10 kA rupturing capacity fixed in DB's including taking down old one complete, all as specified and directed. Make: Hager Cat Part No. NCN106N, Schneider Cat Part No. A9N4P32C / Indoasian Cat Part No. 81195.

Supply and fix in repair MCCB four pole , 415 Volt, 125 Amps,25 kA , adjustable thermal & fixed magnetic setting complete all as specified and directed.Make: Havells Cat part No - IHLGHF0125 or equivalent in Schnieder / GE / C&S / Indoasian / L&T / Legrand.

Material and labour for sub main wiring with two single core 6.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 6.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed, including taking down unserviceable one.(Note: two run of 6.0 sqmm cable , one run of earth wire of 6.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex/RR cable/Havells, PVC Casing Capping- PrestoPlast/Finolex/Kalinga.

M&L for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers, galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30cm X 5 cm with 10mm dia TMT bars 8 cm c/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete including taking down old unserviceable one, all as shown in Electrical Plate No 3 of SSR part -I.

M/S U.K ENTERPRISE