REPAIRS AND POLISHING OF CERTAIN WOODEN FURNITURE AND RECANNING OF ALL SORTS OF CHAIRS INCLUDING REPAIR TO TRADE PATTERN FURNITURE AT AOR OF BSO(S) OF GE(SOUTH) BANGALORE.

Amount

Bed plywood top with MNF set (Applicable to item No 01 to 05) Drg No FD- 246 Removing the existing unserviceable broken wooden long rail and supply of first class hard wood (Teak wood) new long rail of size 35mmx90mmx1980 mm including 35 mm x 5mm flat iron of mild steel bent to right angles as shown on drg and as as directed.

Removing the existing unserviceable broken wooden head board including legs and supply and fix 900x400mm new head board including teak wood legs of size 60mmx60mmx400mm and all as specified and as shown on drgs.

Removing the existing unserviceable /broken foot board including legs and supply and fix 900x300mm new foot board including teak wood legs of size 60mmx60mmx30mm and all as specified/directed and as shown on drg.

Removing the existing unserviceable /broken wooden stiffeners (supporting pieces) and supply and fix first class hard wooden stiffeners of size 40cmx60cm complete all as specified/directed and as shown on drg.

Removing the existing unserviceable plywood and supply and fix 900mmx1800mm x 12mm thick plywood commercial BWR grade bearing ISI marked all as specified/directed and as shown on drg.

Side board (Applicable to item Nos 06 to 14)Drg No FD-241 Removing the existing unserviceable top and supply and fix new top made out of 18mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination not less than 1.5mm thick of sizes 1220mmx455mm etc complete all as specified/directed and as shown on drg.

Removing the existing unserviceable side and supply and fix new side made out of 18mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination not less than 1.5mm thick of sizes 760mmx455mm etc complete all as specified/directed and as shown on drg. Note:-Each side shall be measured as single units.

Removing the existing unserviceable back of side board and supply and fix new back with 6mm thick plywood, grade BWR, type BB with no. of ply 5, ISI marked of sizes 1220mmx700mm all as specified/directed and as shown on drg.

Removing the existing unserviceable bottom of drawer and supply and fix new 12mm thick plywood, grade BWR, type BB with no. of ply 7 of size 380mmx450mm all as specified/directed and as shown on drg.

Removing the existing unserviceable drawer and supply and fix new drawer of size 380mmx450mmx155mm, made out of teak wood plank 12 mm thick for sides and back and 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for front and 6mm thick plywood for bottom of drawer, including fittings such as knobs etc all as specified/directed and as shown on drg. Note:-Each drawer will be measured as single unit.

Removing the existing unserviceable shutter and supply and fix new shutter of size 600mmx390mm made out of 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, including hinges, kobs and lock all as specified/directed and as shown on drg. Note:- Each shutter will be measured as single unit.

Removing the existing unserviceable bottom of side board and supply and fix new bottom of sizes 455mmx1228mm, made out of 18mm thick plywood, grade BWR, type BB all as specified/directed and as shown on drg.

Removing the existing unserviceable leg frame and supply and fix new teak wood leg frame with legs, sizes 1140mmx 380mm, etc complete all as specified/directed and as shown on drg.

Removing the existing unserviceable broken wooden legs and supply and fix new teak wood leg, size 45mmx45mmx125mm etc complete all as specified/directed and as shown on drg. Note:- Each leg will be measured as single unit.

Table writing (Applicable to item Nos 15 to 20) Drg No FD-249 FD-33 FD-275 Removing the existing unserviceable broken top and supply and fix new top made out of 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick teak wood edging, size 1145mmx600mm all as specified/directed and as shown on drg.

Removing the existing unserviceable/ damaged cupboard shutter and supply and fix new shutter made out of 18 mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, size 400mmx700mm, including piano hinges and brass lock all as specified/directed and as shown on drg.

Removing the existing unserviceable drawer and supply and fix new drawer size 300mmx600mmx75mm, made out of teak wood plank 12 mm thick for sides and back and 18mm thick prelaminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for front and 6mm thick plywood for bottom of drawer (Plywood, grade BWR, type BB with no. of ply 5) including fittings such as knobs etc all as specified/directed and as shown on drg. Note:- Each drawer will be measured as single unit.

Removing the existing unserviceable back and supply and fix new back size 1145mmx700mm, made out of 6mm thick Plywood grade BWR, type BB, no. of ply 5, with two coats of synthetic enamel paint over a coat of primer all as specified/directed and as shown on drg.

Removing the existing unserviceable side and supply and fix new side size 600mmx700mm, made out of prelaminated particle board, 18mm thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination all as specified/directed and as shown on drg. Note:- Each side will be measured as single unit.

Removing the existing unserviceable leg and supply and fix new teak wood leg size 35mmx55mmx717mm, etc complete all as specified/directed and as shown on drg.

Table dining 6 persons1500mm x 900mm (Applicable to item Nos 21 to 24) Drg No FD-273 FD-239 Removing the existing unserviceable damaged top and supply and fix with a new prelaminated particle board 18mm with 6 mm thick teak wood edging all round of size 1500mmx900mm all as specified/directed and as shown on drg.

Removing the existing unserviceable damaged front and back rails & supply and fix new teak wood front and back rails of size 25mmx100mmx1500mm all as specified/directed and as shown on drg

Removing the existing unserviceable damaged leg and supply and fix new teak wood leg of size 75mmx40mmx760mm all as specified/directed and as shown on drg .

Removing the existing unserviceable damaged side rails and supply and fix new teak wood side rails of size 25mmx100mmx900mm all as specified/directed and as shown on drg.

Table dining 8 persons 1800mm x 900mm (Applicable to item Nos 25 to 28) Drg No FD-273 FD-239 Removing the existing unserviceable damaged top and supply and fix new top with a new prelaminated particle board 18mm with 6 mm thick teak wood edging all round of size 1800mmx900mm all as specified/directed and as shown on drg..

Removing the existing unserviceable damaged front and back rails & supply and fix new teak wood front of size 15mmx100mmx1800mm and back rails all as specified/directed and as shown on drg..

Removing the existing unserviceable damaged leg and supply and fix new teak wood leg all as specified and as shown on drg of size 75mmx40mmx700mm.

Removing the existing unserviceable damaged side rails and supply and fix new teak wood side rails of size 25mmx100mmx900mm all as specified and as shown on drg .

Table peg (Applicable to item Nos 29 to 32) Drg No FD-384 FD-25 FD-236 Removing the existing unserviceable top and supply and fix new top of size 450x300 mm made out of 18mm thick pre-laminated particle board and 4mm thick teak wood edging round the top of table all as specified and as shown on drg.

Removing the existing unserviceable bottom rail and supply and fix new teak wood bottom rail of size 20x 40x300mm all as specified and as shown on drg.

Removing the existing unserviceable front/back rail and supply and fix new teak wood front/back rail of size 20x 40x450mm all as specified and as shown on drg.

Removing the existing unserviceable leg and supply and fix new teak wood leg of size 30x50x380 mm all as specified and as shown on drg.

Table centre (Applicable to item Nos 33 to 36) Drg No FD-29 FD-274 FD-235 Removing the existing unserviceable top and supply and fix new top of size 900mm x 450mm made out of 18mm thick pre laminated particle board and provided 4mm thick teak wood beading alround of table top all as specified and as shown on drg.

Removing the existing unserviceable leg and supply and fix new teak wood leg of size 30mmx60mmx400mm all as specified and as shown on drg.

Removing the existing unserviceable long rail of size 30mmx60mmx900mm and supply and fix new teak wood long rail all as specified and as shown on drg.

Removing the existing unserviceable short rail of size 30mmx60mmx450mm and supply and fix new teak wood short rail all as specified and as shown on drg.

Table dressing with mirror ladies (Applicable to item Nos 37 to 44) Drg No FD-32 FD-251 Removing the existing unserviceable drawers and supply and fix new drawers of size 300mmx380mm & 315mmx115mm made out of teak wood plank 12mm thick for sides/ back and 18 mm thick pre-laminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination for front and 6 mm thick plywood, grade BWR, type BB with no. of ply 5 for bottom of drawers, including fittings such as knobs etc all as specified and as shown on drg. Note:-Each drawer shall be measured as single unit.

Removing the existing broken glass shutters and supply and fix new glass shutters of size 300mmx390mm all as specified and as shown on drgs. Note:- Each glass shutter will be measured as single unit.

Removing the existing unserviceable aluminium channel and supply and fix new aluminium channel of width 10mm thick suitable for the drawer of size 530mm long all as shown on drgs.

Removing the existing unserviceable plywood portion from back of mirror and supply and fix new back with frame of size 395mmx1230mm made out of 6 mm thick plywood, grade BWR, type BB with no of ply 5 all as specified and as shown on drgs.

Removing the existing unserviceable mirror and supply and fix new mirror of size 365mmx1220mm, 5 mm thick complete all as specified and shown on shown on drgs.

Removing the existing unserviceable 12mm ply wood from back and supply and fix new back of size 395mmx900mm of table dressing ladies made out of 12 mm thick plywood commercial quality all as specified and as shown on drgs.

Removing the existing unserviceable frame with legs and supply and fix new teak wood frame with 4 legs of size 235mmx40mmx25mm & 650mmx40mmx25mm all as specified and shown on drgs.

Removing the existing unserviceable leg and supply and fix new leg made out of teak wood of 04 Nos legs of size 155x45x45mm all as specified and as shown on drgs. Note:- Each leg shall be measured as single unit.

Table dressing with mirror gents (Applicable to item Nos 45 to 49) Drg No FD-31 FD-230 Removing the existing unserviceable top of table dressing Gents and supply and fix new top of size 900mmx300mm made out of 18 mm thick pre laminated particle board all as shown on drgs

Removing the existing unserviceable bottom of table dressing Gents and suplply and fix new bottom of size 900mmx300mm made out of 18 mm thick plywood commercial quality all as shown on drgs.

Removing the existing unserviceable side partition and supply and fix new side partition of size 300mmx135mm made out of 18mm thick pre-laminated particle board all as shown on drg. Note : Each side or partition shall be measured as single unit.

Removing the existing unserviceable drawers of size 4x280mmx130mm of table dressing Gents and supply and fix new drawers made out of teak wood plank 12mm thick for sides and back and 18 mm thick pre-laminated particle board for front and 6 mm thick plywood for bottom of drawers with fitting such as knobs etc all as specified and as shown on drg. Note : Each drawer shall be measured as single unit.

Removing the existing unserviceable mirror and supply and fix new mirror of size 390mmx760mm, 5mm thick with back and frame all as specified and as shown on drgs including with teak wood support all as shown on drgs and as directed.

Table 900X600 with drawer (Applicable to item Nos 50 to 53) Drg No FD-41 FD-283 FD-224 Removing the existing unserviceable table top and supply and fix new top of size 900mmx600mm of prelaminated particle board 18mm of size interior grade with 4mm thick teak wood edging all round all as specified and as shown on drgs.

Removing the existing unserviceable/damaged front and back rails and supply and fix new teak wood front and back rails of size 25mmx130mmx740mm all as specified and as shown on drg.

Removing the existing unserviceable damaged leg and supply and fix new teak wood leg of size 60mm to 40mm(bottom) with a height of 735mm all as specified and as shown on drg.

Removing the existing unserviceable damaged side rails and supply and fix new teak wood side rails of size 25mmx130mmx440mm all as specified and as shown on drg.

Teapoy (Applicable to item Nos 54 to 57) Drg No FD-34 FD-278 FD-232 FD-382 Removing the existing unserviceable top and supply and fix new top of size 600mmx450mm made out of 18mm thick pre-laminated particle board exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination with 4mm thick teak wood edging al-round the top of teapoy all as specified and as shown on drg.

Removing the existing unserviceable leg and supply and fix new teak wood leg of size 515mmx45mmx45mm all as specified and as shown on drg.

Removing the existing unserviceable front and back rail and supply and fix new teak wood of size 450mmx50mmx20mm all as specified and as shown on drgs.

Removing the existing unserviceable side rail and supply and fix new teak wood side rail of size 390mmx50mmx20mm all as specified and as shown on drgs.

Table bed side (Applicable to item Nos 58 to 62) Drg No FD/E6/MAP/15(R ) Removing of UNSV top from table bed side and supply and fixing new top made out of 18mm thick prelaminated particle board with edging fixed to frame all as shown on drawing and all as directed by Engineer-in-charge

Removing of UNSV side from table bed side and supply and fixing new side made out of 18mm thick prelaminated particle board fixed to frame with suitable size of screws all as shown on drawing and all as directed by Engineer-in-charge

Removing of UNSV back ply from table bed side and supply and fixing new back made out of 18mm thick plywood fixed to frame with suitable size of screws all as shown on drawing and all as directed by Engineer-in-charge

Removing of UNSV drawers from table bed side and supply and fixing new drawer made out of 18mm thick prelaminated particle board all as shown on drawing and all as directed by Engineer-in-charge

Removing of UNSV handle from table bed side and supply and fixing new handle of size 100mm long MS all as shown on drawing and all as directed by Engineer-in-charge

Book case Drg No FD-237 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/abbrassive cloth throughly smooth and clean off and applying one coat of french polishing to required finish complete all as specified and as directed.

Side Board Drg No FD 241 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table 900x600 with Drawer Drg No FD-41 FD-283 FD-224 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table bed side Drg No FD-28 FD-276 FD-243 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table Dressing Gents Drg No FD-31 FD-230 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table Dressing Ladies Drg No FD-32 FD-251 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Bed plywood top Drg No FD 246 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Binsoiled linen large Drg No FD 70 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Chair dining Drg No FD - 16 & FD - 279 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish complete all as specified and as directed.

Chair dining Map : Drg No FD/MAP II/04 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish complete all as specified and as directed.

Chair Easy Drg No FD-17 FD-229 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Chair writing Drg No FD-20 FD-280 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Hat stand with mirror Drg No FD-233 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Peg table Drg No FD - 384 FD-25 FD-236 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Sofa Set 4 Seater Drg No FD - 258 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying ono coat of french polish to required finish complete all as specified and as directed.

Sofa Set 5 Seater Drg No FD-281 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Stool Dressing Drg No FD - 27 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table 900x600 W/o Drawer Drg No FD-284 FD-42 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table Centre Drg No FD-29 FD-274 FD-235 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table dining 6 persons Drg No FD-273 FD-239 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table dining 8 persons Drg No FD-273 FD-239 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Table office officer wooden Drg No DB-4199 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish complete all as specified and as directed.

Table writing Drg No FD-249 FD-33 FD-275 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Teapoy Drg No FD-34 FD-278 FD-232 FD-382 Preparing the wooden surfaces by scraping and filling bore holes with putty and rubbing by sand paper/ abbrasive cloth throughly smooth and clean off and applying one coat of french polish to required finish complete all as specified and as directed.

Sofa sets (Applicable to item Nos 87 to 95) Drg No FD-281 Removing the existing unserviceable tapestry cloth, cushion and replacing with new tapestry cloth as per sample with foam cushion of size 560mmx530mm, 40 density, 100mm thick, including inner cloth all as shown on drgs and as directed. Note :- Each cushion for seat or back will be measured as single unit.

Removing the existing unserviceable leg from Sofa and supply and fix new teak wood leg of size 35mmx75mmx510mm all as shown on drg and as directed.

Removing the existing unserviceable arm rest from sofa and supply and fix new teak wooden arm rest all as shown on drawing and as directed .

Removing the existing unserviceable side rail from sofa and supply and fix new teak wood side rail of size 35mmx100mmx690mm all as shown on drawing and as directed .

Removing the existing unserviceable bearer from sofa long pieces and supply and fix new teak wood bearer of size 590mmx50mmx22mm all as shown on drawing and as directed .

Removing the existing unserviceable bearer from sofa short pieces and supply and fix new teak wood bearer of size 440mmx50mmx22mm all as shown on drawing and as directed .

Removing the existing unserviceable battens from sofa and supply and fix new teak wood battens of size 570mmx50mmx22mm all as shown on drawing and as directed .

Removing the existing unserviceable front rail from sofa long pieces and supply and fix new teak wood front rail all as shown on drawing and as directed .

Removing the existing unserviceable front rail from sofa short pieces and supply and fix new teak wood front rail of size 22mmx102mmx1740mm all as shown on drawing and as directed .

Sofa set (Applicable to item Nos 96 to 103) Drg No FD - 258 Removing the existing unserviceable tapestry cloth, cushion and replacing with new tapestry cloth with foam cushion 40 density, 50 mm thick all as shown on drgs and as directed. Note:- Each cushion for seat or back will be measured as single unit. Tapestry cloth to be provided as per sample.

Removing unserviceable plywood 12 mm from seat of sofa set and fix new plywood 12 mm ISI marked BWR grade of size 670mm x 690mm for chairs and as specified in drg

Removing unserviceable Plywood 12 mm from seat of sofa set and fix new plywood 12 mm ISI marked BWR grade of size 1740mmx 690mm for chairs and as specified in drg

Removing the existing unserviceable front leg from Sofa and supply and fix new teak wood leg of size 30mm x 75mm x 510mm all as shown on drg and as directed.

Removing the existing unserviceable back leg from Sofa and supply and fix new teak wood leg of size 30mm x 75mm x 760mm all as shown on drg and as directed.

Removing the existing unserviceable wooden front bearer from Sofa and supply and fix new teak wood front bearer of size 20mm x 50mm x 1740mm all as shown on drg and as directed

Removing the existing unserviceable side rail from Sofa and supply and fix new teak wood side rail of size 30mm x 102mm x 690mm all as shown on drg and as directed.

Removing the existing unserviceable back support rail from sofa and supply and fix new teak wood back support rail of size 20mm x 102mm x 1740mm all as shown on drg and as directed.

Sofa set Drg No TP Removing the existing unserviceable fabric, cushion and replacing with new fabric with foam cushion 40 density, 50 mm thick all as shown on drgs and as directed. Note:- Each cushion for seat or back will be measured as single unit. Fabric to be provided as per sample.

Chair Dining Drg No FD - 16 & FD 279 Removing the existing unserviceable cane from chair dining of size 440mm x 430mm and recanning with new best quality of plastic cane size 1.80mm x 0.46 mm for weaving and 3mm x 0.60 mm for beading as per Godrej pattern all as specified and as directed.

Chair writing Drg No FD - 20 FD 280 Removing the existing unserviceable cane from Chair writing of size 535mmx470mm and recanning with new best quality of plastic cane size 1.80mm x 0.46 mm for weaving and 3mm x 0.60 mm for beading as per Godrej pattern as specified/directed.

Chair easy Drg No FD - 17 FD 229 Removing the existing unserviceable cane from Chair easy seat/back rest of size 575mmx510mm & 420mmx330mm and recanning with new best quality of plastic cane size 1.80mm x 0.46 mm for weaving and 3mm x 0.60 mm for beading as per Godrej pattern as specified/directed.

Bin soiled linen Drg No FD - 15 FD 244 Removing the existing unserviceable cane from bin soiled linen of size 280mmx370mm and recanning with new best quality of plastic cane size 1.80mm x 0.46 mm for weaving and 3mm x 0.60 mm for beading as per Godrej pattern as specified/directed.

Stool Dressing CB Drg No FD- 27 FD-282 FD-374 Removing the existing unserviceable cane from stool dressing CB of size 420mmx275mm and recanning with new best quality of plastic cane size 1.80mm x 0.46 mm for weaving and 3mm x 0.60 mm for beading as per Godrej pattern as specified/directed.

Chair Verandah (Applicable to item Noss 110 to 112) Drg No FD-19 FD-256 FD-359 Removing the existing unserviceable cane from chair verandah of size 480mmx460mm and recanning with best quality of plastic cane 4mm wide as per trade pattern as specified/directed.

Material and labour for preparing old steel surfaces of frame of chair verandah with one coat of synthetic enamel paint white colour, as shown on drawing and all as specified/directed.

Supply and fix new hard rubber toes of appropriate size, suitable to chair verandah as shown on drawing and all as specified/directed.

Chair Dining FD (Applicable to item Nos 113 to 118) Drg No FD-16 FD-179 Removing the existing unserviceable rear leg and supply and fix new teak wood rear leg of size 890mmx65mmx65mm complete all as shown on drg and as specified/directed.

Removing the existing unserviceable front leg and supply and fix new teak wood front leg of size 455mmx45mmx45mm complete as shown on drg and as specified/directed.

Removing the existing unserviceable back rest and supply and fix new teak wood back rest of size 380mmx50mmx19mm complete as shown on drg and as specified/directed.

Removing the existing unserviceable front rail and supply and fix new teak wood front rail of size 400mmx65mmx30mm including drilling holes at 12.5 mm C/C complete as shown on drg and as specified/directed.

Removing the existing unserviceable rear rail and supply and fix new teak wood rear rail of size 400mmx65mmx30mm including drilling holes at 12.5 mm C/C complete as shown on drg and as specified/directed.

Removing the existing unserviceable side rails and supply and fix new teak wood side rails of size 380mmx65mmx30mm including drilling holes at 12.5 mm C/C complete as shown on drg and as specified/directed.

Chair Writing (Applicable to item Nos 119 to 125) Drg No FD-20 FD-280 Removing the existing unserviceable rear leg and supply and fix new teak wood rear leg of size 890mmx65mmx65mm complete as shown on drg and as specified/directed..

Removing the existing unserviceable front leg and supply and fix new teak wood front leg of size 675mmx45mmx45mm complete as shown on drg and as specified/directed.

Removing the existing unserviceable back rest and supply and fix new teak wood back rest of size 445mmx65mmx12mm complete as shown on drg and as specified/directed.

Removing the existing unserviceable front rail and supply and fix new teak wood front rail of size 490mmx65mmx30mm including drilling holes at 12.5 mm C/C complete as shown on drg and as specified/directed.

Removing the existing unserviceable rear rail and supply and fix new teak wood rear rail of size 440mmx65mmx30mm including drilling holes at 12.5 mm C/C complete as shown on drg and as specified/directed.

Removing the existing unserviceable side rails and supply and fix new teak wood side rails 440mmx65mmx30mm including drilling holes at 12.5 mm C/C complete as shown on drg and as specified/directed.

Removing the existing unserviceable/ broken Arm rest and supply and fix new teak wood Arm rest of size 495mmx50mmx19mm complete as shown on drg and as specified/directed.

Chair easy FD (Applicable to item Nos 126 to 131) Drg No FD-17 FD-229 Removing the existing unserviceable rear leg and supply and fix new teak wood rear leg of size 535mmx40mmx40mm complete as shown on drg and as specified/directed.

Removing the existing unserviceable front leg and supply and fix new teak wood front leg of size 535mmx40mmx40mm complete as shown on drg and as specified/directed.

Removing the existing unserviceable broken Arm rest and supply and fix new teak wood arm rest of size 610mmx55mmx25mm complete as shown on drg and as specified/directed.

Removing the existing unserviceable front frame and supply and fix new teak wood front frame of size 53mmx70mmx25mm including drilling holes at 12.5 mm C/C complete as shown on drg and as specified/directed.

Removing the existing unserviceable front rail and supply and fix new teak wood front rail of size 520mmx55mmx25mm complete as shown on drg and as specified/directed.

Removing the existing unserviceable rear rail and supply and fix new teak wood rear rails of size 500mmx50mmx25mm complete as shown on drg and as specified/directed.

Stool Dressing CB (Applicable to item Nos 132 to 134) Drg No FD-27 FD-282 FD-374 Removing the existing unserviceable leg and supply and fix new teak wood leg of size 350mmx40mm complete as shown on drg and as specified/directed.

Removing the existing unserviceable front rail and supply and fix new teak wood front rail of size 355mmx50mmx25mm including drilling holes at 12.5 mm C/C complete as shown on drg and as specified/directed.

Removing the existing unserviceable side rails and supply and fix new teak wood side rails of size 220mmx50mmx25mm including drilling holes at 12.5 mm C/C complete as shown on drg and as specified/directed.

Chair dining Officers (Applicable to item Nos 135 to 142) Drg No FD/MAP II/04 Removing unserviceable seat of chair dining officers with cushion and supply and fix new seat of size 450mmx450mm made out of 75 mm thick 40 Density foam covered with tapestry cloth nailed to 12 mm thick Phenol Bonded plywood commercial, complete all as shown on drg and as specified/directed

Removing unserviceable front leg of chair dining officers and supply and fix new teak wood leg of size 420mmx50mm x 35mm complete as shown on drg and as specified/directed.

Removing unserviceable back leg of chair dining officers and supply and fix new teak wood back leg of size 950mm x 50mm x 35mm duly curved, complete all as shown on drg and as specified/directed.

Removing unserviceable side rail of chair dining officers and supply and fix new teak wood side rail of size 450mmx65mm x 25mm complete all as shown on drg and as specified/directed.

Removing the unserviceable front rail of chair dining officers and supply and fix new teak wood front rail of size 420mmx65mm x 25mm complete as shown on drg and as specified/directed.

Removing unserviceable back rail of chair dining officers and supply and fix new teak wood back rail of size 420mm x 90mmx25mm complete all as shown on drg and as specified/directed.

Removing unserviceable side Stiffner of chair dining officers and supply and fix new teak wood side Stiffner of size 450mmx25mmx20mm complete all as shown on drg and as specified/directed.

Removing unserviceable middle Stiffner of chair dining officers and supply and fix new teak wood middle Stiffner of size 420mmx25mmx20mm as shown on drg and as specified/directed.

Hat Stand with mirror (Applicable to item Nos 143 to 145) Drg No FD-233 Removing unserviceable plywood from hat stand and supply and fix new plywood 4mm thick, one side teak face finish of size 1000mm x 710 mm including teak wood edging size 6 mm x 35 mm duly polished complete all as shown on drg and as specified/directed.

Removing unserviceable mirror from hat stand and supply and fix new 5 mm thick mirror of size 300 mm x 440 mm including teak wood edging size 10 mm x 12 mm as shown on drgs and as specified/directed.

Removing unserviceable aluminium pegs from hat stand and supply and fix new brass pegs of size120mmx75 mm (over all) with brass screws as shown on drgs and as specified/directed.

Chair writing steel (Applicable to item Nos 146 to 149) Drg No FD/E6/MAP/12 Removing the existing unserviceable damaged 120mm hot pressed plywood and supply and fix new 120mm hot pressed plywood of approx size 950mmx500mm upholstered with fabric and moulded polyurethane foam with pvc lipping all round.

Removing the existing unserviceable damaged foam and supply and fix new polyurethane foam of approx size 950mmx500mm shall be 50mm thick and shall be moulded with density 50-55 kgs per cum and hardness 20 +/- 2 kgs/m2 on hampden machine.

Removing the existing unserviceable damaged armrest and supply and fix new armrest made of black integral skin polyurethane with 75-85 hardness and reinforced with MS insert it shall be scratch and wheather resistant both hand rest sections to have slope towards front.

Removing the existing unserviceable damaged contoured lumber support and supply and fix new contoured lumber support for extra comfort.

Chair computer/Chair revolving Drg No FD/E6/MAP/ 01 Removing the existing un serviceable seat (cushioned) and supply and fix the new seat of seat 510mm x 470mm x 60mm (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam with PVC lipping. (Make : Godrej or equivalent)

Chair cushion with Arms/Chair visitor Drg No TP Removing the existing un serviceable seat (cushioned) and supply and fix the new seat of seat 510mm x 470mm x 60mm (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam with PVC lipping for chair cushion with arms/chair visitor all as shown on drg and as directed.

Chair revolving padded with Arm high back Drg No FD-75 Removing the existing un serviceable seat (cushioned) and supply and fix the new seat of seat 510mm x 470mm x 60mm (12 mm hot pressed ply wood, upholstered with fabric and moulded polyurethane foam with PVC lipping for chair revolving padded with arm high back all as shown on drg and as directed.

Chair revolving padded with Arm high back (Applicable to item Nos 153 to 157) Drg No FD - 75 Removing the existing un serviceable back and supply and fix the new back (12 mm th hot pressed ply wood, upholstered with fabric and moulded polyurethane foam. The back form shall be designed with contour lumber support for extra comfort with PVC lipping for chair revolving padding with arm high back all as shown on drg and as directed.

Removing the existing broken bottom gas lift (Up & Down) hydraulic with pouch (Maintenance free environmental friendly, chrome free cylinder tube shll be fixed in a MS black powder coated outer central column tube 38 mm dia and 2mm thick. It shall have 100 mm stroke length and gas pressure of 300 newton force, should under go an impact test)from revolving chairs, computer chairs supply and fix new bottom gas lift (hydraulic) with pouch of Make : Godrej or equivelent Note : Adjustable Tilting Mechanism to be designed with the following mechanism. Forward tilt, self regulating tilt tension + manual override, 4 position tilt lock. Anti-shock back mechanism to prevent back rest from hitting the user when the lock released. 360 swivel mechanism to allow fluid lateral movement)

Removing the existing broken twin caster wheel from revolving chairs ,computer chairs ,Tables TV Trolley etc ,supply and fix new fibre caster wheel Make : Godrej or equivalent

Removing the existing broken Pedestal assy (injection moulded in black 30% Glass filled nylone A 10.5 MM dia forged bright Zinc plated MS castor pin is of press fitted into each prong for holding the cators. It is 600 mm pitch-centre Dia) from revolving chairs & computer chairs ,supply and fix new Fibre Stem Base of Make : Godrej or equivalent

Removing the existing broken padded Arm rest (Black integral skin polyurethane finforced with MS insert. It shall be scratch and weather reisistant) as per sample from revolving chairs & computer chairs ,supply and fix new arm rest make : Godrej or equivalent

REENA INDUSTRIES

PRIYADARSHINI CONSTRUCTIONS

SHANMUGA TRADERS

Vivek Engineers