Repair Repalacement of Roof, Floors, Joinery, Plaster, Plumbing and other Allied works at 9 Inf Div Amn Dump Restricted Area Sofipur, 22 Inf Div Amn Dump Restricted Area Sofipur, Baffle Range, 32 MVH and other Adjacent Area under AGE B/R-II of GE (

Amount

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

Taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new frame complete all as specified and directed by Engineer-in-charge.

Taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge.

Taking down shutter/ leaf only of any description area exceeding 2 sqm each complete all as specified and directed

Taking down and refixing door shutters of any description of area exc 1.0 Sqm but n.exc 2.0 Sqm each in the same opening including easing of door/window/cup board shutters for easy closing/ opening incl tightning of hinges or changing the position of hinges adjustment of tower bolts, sliding bolts etc complete all as specified and directed by Engr-in-Charge. Note : Labour for taking down of shutter incl in this item, nothing shall be paid extra.

Demolition cement concrete (Unreinforced) in ground floor and paving n exc 15 cm thick below or above ground level complete all as specified and directed.

Demolition brick work / stone masonry built in cement mortar complete in any condition all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable to store and rubbish off the premises complete all as specified and directed.

Demolition stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded, jointed and pointed in any mortar complete all as specified and directed by Engineer-in-charge.

Dismantling posts or struts (wood, steel or RCC) any section embedded in concrete and brick work, including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engineer-in-Charge.

Dismantling AC sheet corrugated or semi corrugated sheet inc. ridges of any description as in roof and including removal from the site complete all as specified and directed.

Dismantling wall or ceiling board (fibre, pulp, insulation etc) any thickness including cover fillets and removal from the site complete all as specified and directed.

Dismantling snap grid for false celling of any description and size complete all as specified and directed.

Dismantling unframed work timber scantlings 40 Sq.cm and over in section, in any position complete all as specified and directed

M&L for cutting and removing of bushes, small trees, vegetation (Peepal, bad small plants etc) of any ida and girth from roof projection, chajjas, wall junction, parapet etc at any height by necessary demolition of brick work, cement plaster, digging out roots from concrete or brick wall filling holes on building wall/roof/chhajja/water tank staging area etc and making good with cement mortar 1:4 complete all as specified and directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan exceeding 6 cm mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for (Except brick) brick work with Sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in CM 1:4 complete all as specified and directed

M&L for rendering 15mm thick in CM 1:4 on brick / concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for PCC 1:3:6, Type C–1, using 20 mm graded stone aggregate as in coping including use and waste of form work and finishing the exposed faces of concrete even and smooth without using extra cement complete all as specified and as directed.

M&L for PCC 1:2:4, Type B–1, using 20mm graded stone aggregate as in Surface Channels and Drain etc.complete all as specified and as directed.

Extra for forming fair finishing drain or channel 30cm inner girth in cement concrete, using extra cement incl forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M&L for applying 15mm thick rendering in CM 1:4 using ready mix plaster bags on brick/concrete surfaces of walls, pillars & columns finished even and fair complete all as specified and directed

M&L for rendering 15 mm thick in cement mortar 1:4 on chajjas/beam/Ceiling or surfaces other than fair face of brick work or concrete surfaces at any height complete all as specified and directed

M&L for rendering 10mm thick in CM 1:6 on other than fair face of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for 5mm thick rendering on concrete surface of ceiling in cement mortar (1:3) finished even and smooth without using extra cement complete all as specified and as directed .

M&L for clean the surface using wire brush, remove existing paint wall putty and remove the entire loose particles from the dampness surfaces of walls and apply Dampguard solution mixed with wall care putty and apply two coats of mixed solution as per manufacturer instrution or as directed by Engr-in-Charge.

M&L for preparation new plastered or unplastered surfaces and applying two coats of distemper oil emulsion white tinted over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation new plastered or unplastered surfaces and applying two coat of cement base paint over a coat of chalk whiting, on plastered surfaces, prepara-tory to distempering complete all as specified and directed.

M&L for preparation new plastered surface of ceiling and applying three coats of white wash complete all as specified and as directed

M&Lfor preparation old decorated plastered surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

M&L for preparation old decorated plastered surfaces of walls and applying two coat of white wash complete all as specified and directed

M&L for preparation old plastered/ decorated surface of walls incl scraping down smoke soot, moulds, moss & efflorescent salts & trading oil and greesing spots etc & applying two coats of exterior emulsion paint (Camouflage pattern) complete all as specified and directed.

M&L for preparation old plastered/ decorated surface of walls and applying two coat of cement based paint at any height complete all as specified and directed.

M&L for preparation old plastered or unplastered surfaces of walls and applying two coats of bound distemper using roller for painting over a coat of 2mm thick wall care putty complete all as directed and specified.

M&L for preparation old plastered/ decorated surface of ceiling and applying two coats of oil bound distemper complete all as directed and specified.

M&L for prepration old wooden surfaces of any description not otherwise described over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for prepration old steel or iron surfaces of any description not otherwise described over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for preparation new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation new steel or iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F Fe - 290 (Gde E- 165) for Framed work as in doors , chowkhats or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, support to velley gutters, winties for roof sheets, framing for monkey proofing, welded mesh, support to sign board & fencing post, etc as specified to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

S&F Rolled sections Fe 410 -W (grade E-250) quality-A as in main and cross beams, base plates, side supports, hip and jack rafters; purlins, winties where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting member complete all as specified and directed.

S&F in repairs rolled mild steel plate girder or single stanchions built of one beam or channel section with flange plate, caps, bases, spices, angle bracket, cleats and other connection Fe-290 (Gde 165) as specified to be prepared for hanging or sliding with and including either hooks or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and handing also fastening and fixing complete all as specified and directed.

S&F steel windows with pressed steel frame made out form 1.25mm thick steel with one or more rebate with glazed shutters and fly proofing shutters including guard bars, hinges, peg stay, handles, tower bolts, lugs including treated with for or coal tar black paint on steel surface in contact/embeded in concrete/masonry work complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F anodised aluminium sliding glazed window with three track / shutter, three shutter sliding with following specification complete all as specified and directed. (i) Window frame of cross section 101 mm x 44mm x 1.5mm thick (ii) Three way track for sliding shutter of cross section 91.8 mm x 31.75mm x 1.1mm thick (iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick (iv) 4 mm thick tinded glass supeiror quality (v) IDPE rubber gasket for fixing of glass (vi) Locking cleats per shutter 1 Nos (vii) Sliding rollers per shutter - 02 Nos (viii) Aluminium wire cloth 0.30 mm nominal dia of wire and average width of aperture 1.56 for shutter 1 No (ix) Fixing of screw for frame with wall per window -08 Nos (x) Aluminium grill

S&F 30mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces complete all as specified and directed by Engineer-in-charge.

S&F 35m thick glazed and skeleton shutter open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/gauze etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed

S&F 150mm long aluminium anodised, barrel tower boltls of extruded sections and fixed complete all as specified and directed

S&F 150mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed

S&F 100mm size mild steel butt hinges cold rolled medium weight (ISI marked) complete all as specified & directed.

S&F 200 mm long mild steel barrel tower bolt stove enamelled black with bright bolt (ISI marked) complete all as specified & directed.

S&F 150mm mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S&F 200mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed

S&F MS door springs for doors, 150 mm, ordinary rat tail rod pattern springs including roller and roller plate and fixing in MS frame or wooden frame complete all as specified and directed

S&F 140mm long Floor door stopper of aluminium alloy body and tonge, anodised with hard drawn steel spring complete all as specified and directed.

S&F in repairs MS barrel tower bolt 200 mm long, stove enamelled black, with bright bolt complete all as specified and directed

S&F in repairs MS pressed handle 150mm long, oval type, stove enamelled black complete all as specified and directed

S&F in repairs 250mm long mild steel sliding door bolts stove enamelled black ISI marked, with bright bolt not less than 12mm dia with and inc min of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed

S&F galvanised steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n. exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares exc 0.50 Sqm in each pane, complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.50 cum, in soft/loose soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and directed.

M&L for cement concrete type C2 1:3:6 (40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparation of steel or iron surface not exceedding 10 cm width or girth and applying two coas of synthetic enamel paint over one coat of red oxide zink chrome primer complete all as specified and directed.

M&L Preparation of surfaces of any description wood/steel, iron etc exc 10cm in width or girth and applying one coat of black bituminous paint on embedded steel post portion complete all as specified and directed

Supply of chain link MS Galvanised fencing , any size or type complete all as specified and directed.

Fixing only in repairs 4mm dia galvanised steel wire,(Chain Link) 100x100mm mesh including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

S&F MS bolts n exc 12 mm dia purpose made with hexagonal or square head one end with nut and screwed the other, or screwed both ends each screwed end to be fitted with washers and one hexogonal or square not exc 30 cm long complete all as specified and directed

S&F Mild steel round bars 10 mm dia and over, cut ot length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. (Fe-410) complete all as specified and directed.

S&F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

M&L for welding in repair of loose joints of sliding doors, hinges, siliding door bolts, garrage doors, windows, doors, northlight framing, monkey proofing framing etc incl at any height & inc necessary cutting and grinding complete all as specified and directed

Taking out old serviceable glass of any description, from old wooden or metal frames, or stone, concrete or brick surrounds, any thickness or size; hacking out old putty or removing beads etc, including making good breakages in taking out and handling removing to store or stacking for reuse as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed to either complete all as specified and directed.

S&F Pre-painted galvalume aluminium zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ Clading to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F Pre-painted galvalume aluminium zink coating GI based Plain steel sheet 0.50 mm lthick of an colour having tensile strength of 550 Mpa as in roof covering/ Clading to wall, Ridge and eaves board, fixed with self tapping screws as in specified complete all as specified and directed.

S&F Anodised aluminium snap grid frame work of size 600mm x 600mm for false ceiling all as specified complete all as specified and directed.

M&L for Exposed metal frame ceiling with calcium silicate board 6mm thick of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified and directed.

S&F Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18Sqm but not exceeding 0.38Sqm as in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles 15mm thick screed bed or bedding layer CM 1:6 for laying floor finishes complete all as specified and directed

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) (Light shade) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles incl 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes complete as specified and directed.

All as per item no 83 above but as in skirting over and including 10mm thick rendering in CM 1:4 as backing coat complete all as specified and directed.

M&L for colored glazed ceramic tiles in vertical surface 450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colored cement laid over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M& L for exterior grade, coloured vitrified ceramic designer floor (Endura) tiles for parking area, paved area, size 300 mm x 300 mm x 10/12mm thick, set,jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour/ matrix of tiles incl 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes complete as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over 15mm thick cement screed bed 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for granite(of any type) tiles 16 to 18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and making suitable holes for gas pipe complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 Type C-2 (40mm graded aggregate) as in sub-floor and pavings, etc. complete all as specified and directed

M&L for laying 60 mm thick machine pressed precast PCC colored interlocking paver block molded in PVC frame / mould any shape and size conforming to IS 15658-2006 of M-35 grade of approved design with gray cement and pigment to match shade / colour / matrix of tiles set and bedded over and including 50mm thick fine river washed sand duly compacted with surface vibrator laid over compacted sub soil in flooring complete all as specified and directed.

M&L for precast chequered cement concrete tiles of size 300x300x25mm thick, with grey cement and pigment, laid in floors with grey cement and joints filled with grey cement and pigment to match colour of tiles complete all as specefied and directed incl 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed

M&L for 75mm thick PCC in plinth protection and paving 1:3:6 type C-1,(20mm gradded aggregate) finishing cement concrete even and smooth in slope without using extra cement complete all as specified and directed

Taking up or down steel tubing 15mm bore and connections, complete all as specified and directed

Taking up or down steel tubing 20mm bore and connections complete all as specified and directed

S&F GI water tubing 15 mm bore medium grade with all fittings fixed to walls and ceiling or laid in floors including cutting screwing and waste etc including taking down of old inserviceable GI water tubing complete all as specified and directed.

S&F GI water tubing 20 mm bore medium grade with all fittings fixed to walls and ceiling or laid in floors including cutting screwing and waste etc including taking down of old inserviceable GI water tubing complete all as specified and directed.

S&F in repairs Rotational moulded polythene water storage tanks (Cylinderical vertical with closed top) hoisted and fixed in position 500 ltrs, including 20 mm bore Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed and dismantling of old water tank complete all as specified and directed.

S&F in repairs Rotational moulded polythene water storage tanks (Cylinderical vertical with closed top) hoisted and fixed in position 1000 ltrs, including 20 mm bore Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed and dismantling of old water tank complete all as specified and directed.

M&L for MS plain sheet 01 mm thick for making modified lid of water tank as per sample kept in offcie of AGE B/R-II and fixed with 04 nuts and bolts for water tanks for water tank capacity n. exc 1000 ltr complete all as specified and directed

S&F in repairs 15mm bore Ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

S&F in repairs 20mm bore Ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed

S&F in repairs viterious china squatting pan Orissa pattern size 580x440mm white with integal foot rest, including concrete bedding, P or S trap lime concrete bedding and all internal fitting, inlet, outlet pipe connections etc & making good floor complete all as spd & directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white with 'P' or 'S' trap (excluding flushing cistern and flush pipe) including connection to drain or out going pipe and to flushing pipe, antisyphonage pipe etc complete all as specified and directed.

S&F in repairs PVC valveless flushing cistern 10 Ltr capacity (white), syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flushing pipe complete all as specified and directed

S&F in repairs viteress china wash basin white flat back size 630X450mm including CP 15mm pillar tap 32mm CP waste coupling, waste pipe and brackets complete all as specified and directed.

S&F in repairs Vitreous china urinals, half stall (back or corner wall tye), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brakets, flush pipe, grating and union for discharge pipe, (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs CP 15mm bore bib tap cast copper alloy with crutch butterfly handle, screwed down and screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F in repairs CP 15mm bore bib tap two way cast copper alloy with crutch butterfly handle, screwed down and screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F in repairs 15mm dia pillar tap, cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered 'Hot or 'cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

S&F in repairs CP angle valve 15mm bore cast copper alloy with crutch butterfly handle, screwed down and screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs 15mm dia stop valves of cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repais 15mm bore Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed

S&F in repairs 15mm bore Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed

S&F in repairs PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repairs PVC waste pipe 32 mm dia 60cm long complete all as specified and directed.

S&F in repairs CP WHB waste coupling of size 32mm complete all as specified and directed.

S&F in repairs PVC Bath cabinet with mirror 18" x 22" x 4.25" complete all as specified and directed.

S&F in repairs CP health faucet set classic chrome 2 in 1 (with tube and hook) with 1 mtr CP tube & Hook complete all as specified and directed.

S&F in repairs CP grating (with and without hole) of size 125mm complete all as specified and directed.

S&F in repairs S/S soap dish fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs Brass chromium plated tubular towel rail 20mm dia , D type 60mm long between flanges complete all as specified and directed.

S&F stainless steel peg set 8 nos in 450mm length stirrupe dia of hooks 6mm complete all as specified and directed.

S&F in repairs powder coated mild steel drapery rod of size 20mm inner dia (in lengths as directed) of approved colour with and including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plugs and screws on walls/beam complete all as specifed and directed by Engr-in-Charge.

M&L for roof treatment in repair by complete removal of existing old treatment and treated with following specifications :- (a) Brushing neat cement slurry @ 3Kg per Sqm on roof slab. (b) 15 mm thick cement plaster fair finished using cement mortar (1:4) with and including WPC on roof slab. (c) Applying oil based bitumen primer @ 0.30 Ltr/Sqm on plastered surface. (d) Applying modified APP polymeric membrane 3mm thick and minimum weight 3.00 Kg / Sqm for water proofing of roof , sealing as directed at site with 100mm over laps as per manufacture's instruction. (e) Applying two coat of aluminium paint @200 gm/Sqm over bituminous surface of membrane.

S&F 110mm bore PVC (SWR) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite number of clamps made out of flat iron 25x4mm complete all as specified and as directed by Engineer-in-charge.

S&F 75mm bore PVC (SWR) pipes in any length jointed with adhesive fixed to walls fixed with and including requisite number of clamps made out of flat iron 25x4mm complete all as specified and as directed by Engineer-in-charge.

S&F in repairs 75mm bore PVC (SWR) bends any radius complete all as specified and directed. Make : Supreme/Finolex/Prince

S&F in repairs 110 mm bore PVC (SWR), junction single, (single T), equal or unequal with access door complete all as specified and directed.

S&F in repairs PVC (SWR) reducers of 110 mm bore complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR), junction single, (single T), equal or unequal with access door complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F in repairs PVC (SWR) cowl, 75 mm bore complete all as specified and directed.

S&F in repairs PVC (SWR) cowl, 110 mm bore complete all as specified and directed.

veer enterprises

vibha associates