SPL REPAIRS TO OH LINE TO UG CABLE AT MD JCO/OR ACCN INCLUDING TOILET BLOCK AND CERTAIN MINOR WORKS AT NEW MIL STN UNDER GE GANTGOK

Amount

SCHEDULE 'A' PART-I (B/R WORKS)

Excavation in trenches not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out as in soft / loose soil complete all as directed by the Engr-in-Charge.

Material & labour for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations filling and mass concrete etc complete all as specified & as directed.

M&L for pre cast cement concrete block masonry with solid blocks, exc. 10 cm in width and settting in cement mortar 1:6 type C1, (1:3:6) (using 20 mm graded stone aggregate) as per IS 383 complete all as specified and as directed.

Returning, filling in, including spreading levelling watering and well ramming in layers not exceeding 25 cms in thick as in soft/loose soils complete all as directed by the Engr-in-Charge.

Removing excavated material to a distance n.exceeding 50m and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as directed by the Engr-in-Charge.

Material and labour for hardcore of gauge n.exc.63mm (using broken stone or boulders) deposited, spread and levelled in layers not exc.15cm thick, watered and rolled/rammed to a true surface complete all as directed.

M&L for 75mm thick PCC (1:4:8), type D-2 (using 40 mm graded stone aggregate ) as in sub -base of floor complete all as specified and as directed

M&L for 30mm thick PCC (1:2:4), type B-1 (using 20 mm graded stone aggregate ) as in sub -base of floor complete all as specified and as directed

Materials & labour for rendering 20 mm thick in cement mortar (1:4) in two layer of 10 mm thick each with using WPC shall be mixed with cement mortar in finishing outer layer only as per manufacturer instruction, on other than fair face of brick/stone masonry surfaces (external surfaces) finished surface fair and even with out using extra cement complete all as specified and as directed. Note: WPC shall be measured and paid separately as supply only.

Supply only integral water proofing compound confirming to IS-2465-2003 of approved make complete all as specified and as directed.

Materials & labour for rendering 15 mm thick in cement mortar (1:4) on fair face of brick or concrete surfaces finished surface even and smooth without using extra cement complete all as specified and as directed.

S&F Rolled section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleat or other connecting plates confirming to Fe-410-W (Gde-E-250) complete all as specified and as directed.

Materials & labour for 0.63mm thick CGI sheeting , ISI marked with 275 grams per sqm zinc coating with two corrugation side laps fixed with 'L' type or 'J' type or cranked hook bolt and washers in roof covering / walls etc etc complete all as specified & as dirceted.

S&F of factory made solid PVC door frame of size 50mmx47mm made out of 5mm thick single side prelam PVC sheet reinforced with mild steel square tube and edges will be painted to match with single side prelam sheet as per specification and drawing given on MES schedule Part-II (2004) complete all as specified & directed.

S&F of 30mm thick (style thickness) factory made solid panel PVC door shutter consisting of frame made out of mild steel tubes for top and bottom rails, solid steel frame shall be covered with heat moulded single side prelam PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail on either side & as gap insert for top rail and bottom rail, paneling of both side prelam PVC sheet to be fitted in the mild steel frame welded /sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement as per specification and drawing given on MES Schedule Part-II (2010) Complete all as specified and directed.

S&F steel ventilator, with top hung shutter including hinges with fixed type MS handles , peg stay and tower bolt but with additional sash bars MS flats for fixing wire gauge complete all as specified & as directed.

S&F 3mm thick figured glass pin head type and glazing with oil putty including steel pin in square n.exc 0.5sq. m in each pane fixed to steel frame complete all as specified & as directed.

S&F 100mm long butt hinges, medium weight, cold rolled, mild steel complete all as specified.

S&F 150 mm long aluminium anodised handles, cast type, complete all as specified and directed

S&F 150mm long aluminum anodised tower bolts of extruded section and fixed complete all as specified and directed.

S&F 250 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

Supply and fix galvanised steel water tubing 20mm bore dia, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as directed.

Supply and fix galvanised steel water tubing 15mm bore dia, medium grade with all fittings and fixed complete to walls/ceiling or laid in floors complete all as directed.

Supply and fix in repair Vitreous China squatting pan of ‘Orissa pattern’, of size 580 mm x 440mm (white) with integral foot rest‘P’ or ‘S’ trap, front or back inlet, any pattern (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including provision of PCC bedding and connection to trap, and to flushing pipe, antisyphonage pipe, etc. complete including making good to floor all as specified and directed by the Engr-in-Charge. Make : Cera Cat No. 2071 (OR) or equivalent make as specified.

Supply and fixing in repair star white vitreous china wash down water closet pan (pedestal pattern) EWC, of size 520 x 360 x 390 mm with ‘P’ or `S' trap, including fixing bolts, Plastic water closet seat and cover, closed pattern with flat bottom, and mild steel chromium plated or aluminised hinging device, making all necessary connections complete all as specified and as directed. Make Cera Cat No. 2008 EWC Model Conventional or equivalent make as specified.

Supply and fix 10 litre capacity low level PVC flushing cistern (white), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed. Make : Cera Cat No. B1010101 or equivalent of make as specified in List of makes.

Supply & fix Bib tap , cast copper alloy, chromium plated Fancy type with crutch or butterfly handle, screwed down for 15mm bore GI Pipe or for brass ferrule complete all as directed. Make : JAQUAR Code : CON-107 KN or equivalent make as speciifed in list of makes

Supply & fix 15 mm bore dia Stop cocks, cast copper, fancy type, chromium plated, with wall flange screwed down, screwed fro iron pipe or union and complete all as directed. Make : JAQUAR Code- CON 059 KN or equivalent make as speciifed in list of makes

Supply and fix PVC connections 15 mm size with PTMT nuts of length 450mm complete all as directed by the Engr-in-Charge. Make- Prayag Cat No 323 or equivalent make as specified.

M&L for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion , white or tinted over a coat of primer over a coat of wall care putty of required thickness as per manufacturers instruction complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of suitable primer complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as directed.

S&F110mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors , fixed on walls with necessary clips complete all as specified and as directed.

Supply & fix in repair 110 mm bore PVC (SWR) vent cowl fixed in position complete all as specified and directed.

Supply and fix in repair110 mm bore PVC (SWR) bend of any radius for PVC (SWR) pipes, fixed to walls or fixed to steel gutter complete all as directed.

Supply and fix 110 mm bore PVC (SWR) junction single,(Single T) equal or unequal complete all as directed .

S&F 75mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors , fixed on walls with necessary clips complete all as specified and as directed.

Supply & fixing Rotational moulded polyethylene water storage tank, 500 litres capacity, ISI marked multi layer constriction (cylindrical vertical with closed top), hoisted & fixed in position including supply and fixing of 25mm bore Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe of having weight not less than 455 gms including connection complete all as specified and as directed and taking down old unserviceable/ broken one

Supply & fix 75 mm dia PVC floor trap of outlet, with gratings, including jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) complete all as specified and as directed.

Material & labour for cutting into existing manholes for connecting new drains (internal dia pipe 100mm), making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching all as directed by the Engr-in-Charge.

M & L for PCC 1:3:6 type C-2 (by using 40 mm graded stone aggregate) as in bed to drain pipes 150 mm bore, including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed by the Engr-in-Charge..

M&L for roughning surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust etc complete all as directed.

Material & labour for non skid coloured ceramic tiles of 7 to 8 mm thick (Square/ rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors etc conforming to IS- 13712, grade B-II - (a) set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including cement screed bed / bedding layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed..

Material & labour for non skid coloured ceramic tiles of 7 to 8 mm thick (Square/ rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in vertical surfaces such as skirting/dado / riser to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed / backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls, including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by the Engr-in-Charge.

S&F powder coated grid frame work for false ceiling comprising of the following sections for making partitions of 600 x 600m size fixed to walls with rawl plugs & screws and hanged to roof with and including 1mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 23mm x 28mm x 0.30mm thick, cross tee shall be 23mm x 28mm x 0.30mm thick and wall angle shall be 20mm x 20mm x 0.30mm thick complete all as specified and as directed.

Supply and fix 4mm thick Non asbestos fibre cement building boards (E-board) of approved texture, for insulation and acoustic purpose of size 595 x 595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surfaces and applying two coats of oil emulsion diatemper over a coat of primer including preparation of surfaces complete all as specified and directed by the Engr-in Charge.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in soft /loose soil complete all as directed by the Engr-in-Charge.

Excavation in post holes (or similar holes) in soft/loose soil each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25 cm and removing surplus soil to a distance n.exc 50 mtrs complete all as specified and directed by the Engr-in-Charge

Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheets of any colour and any pattern as approved having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws as in roof complete all as specified and directed by the Engr-in-Charge.

M&L for pre cast cement concrete block masonry with solid blocks, n exc. 10 cm in width and settting in cement mortar 1:6 type C1, (1:3:6) (using 20 mm graded stone aggregate) as per IS 383 complete all as specified and as directed.

Supply and fix 0.50mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheets of any colour having tensile strength of 550 Mpa as in ridges, valley, eaves, etc fixed with self tapping screws complete all as specified and directed by the Engr-in-Charge

Material & labour for pre-cast RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in lintel, bands,coping, cover slabs and the like etc including necessary form work and set in CM 1:4 complete all as specified & as directed. NOTE : Re-inforcement shall be measured and paid separately.

M&L for mild steel TMT bars,10mm dia and over cut to length, bent to shape required including cranking ,bending spirally, hooping for columns, hookings ends and binding with and including MS wire(annealed) not less than 0.9 mm dia or securing with clips complete all as specified & as directed.

Material & labour for Mild steel TMT bars 6mm to 8mm dia and over cut to length, bent to shape required, including cranking , bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & as directed.

Supply and fix vitreous china, white colour, flat back, wash hand basin of size 55cm x 40cm x 79cm fixed with brackets , including providing 32 mm dia PVC waste pipe , 32 mm bore CP waste coupling with or without padestal and making all necessary connections complete as directed by Engr-in-Charge. Make : Cera Model CORNET Cat No 1008 or equivalent make as specified.

Materials & labour for coloured glazed ceramic tiles of size (300 mm x 200 mm / 350 mm x 250 mm / 450mm x 350mm ) x 7 mm thick as in vertical surfaces such as skirting/dado / riser to steps etc conforming to IS - 13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed / backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed.

Supply and fixed 15mm bore pillar taps, fancy type with long neck with aerator cast copper alloy with capstan head, chromium plated, screwed down, high pressure with long screwed shanks, fly-nuts, with screwed for GI pipe complete all as specified and as directed. Make:Jaquar cat No CON 021 KN or equivalent make as specified.

Cutting opening in cement concrete walls (any descript-ion) for door, window and other openings (with or without reveals)or enlarging existing openings, including trimming surfaces to receive rendering, etc.

SCHEDULE 'A' PART-II (E/M WORKS)

Dismantling of old ACSR conductor from the disturbed span including line spacer and unserviceable material removing from site of work to shifting MES store complete all as directed.

Dismantling of old unserviceable/defective (Pin type, Shackle type) insulators of any size/type and removing materials from site of work to shifting MES store complete all as directed

Dismantling of old cross-arms of mild steel channel or angle sections, etc, including mild steel bolts, nuts, washers, etc. and removing from site of work complete all as directed.

Supply, Laying, jointing & testing 1100 volts grade, XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured LT electric power under ground cables, heavy duty with aluminium stranded conductor laid in trenches or passing through pipe of cross sectional area 95 sqmm 3.50 core with all fixing & connecting accessories complete all as specified & as directed. Note:- (i) Earthwork & Excavation, GI pipe brick protection etc shall be measured and paid separately under relevant items of this schedule. (ii) The rate quoted by the bidder shall deemed to be inclusive of the cost of aluminium thimbles/lugs of suitable sizes."

All as per Srl item No 2.04 here-in- before but for 70 Sqmm 3.5 Core complete all as specified and as directed.

All as per Srl item No 2.04 here-in- before but for 50 Sqmm 3.5 Core complete all as specified and as directed.

All as per Srl item No 2.04 here-in- before but for 16 Sqmm 2.00 Core complete all as specified and as directed.

All as per Srl item No 2.04 here-in- before but for 10 Sqmm 2 Core complete all as specified and as directed.

Supply and laying dry coarse sand as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 cm (15 cm under the cable & 8 cm over the cable) and gently punned down to 18 cm thickness complete all as specified and as directed by the Engr-in-Charge. Note :- Consolidated thickness shall be measured and paid.

Supply and laying in trenches Bricks, sub class 'B' old size bricks of size 230x113x75mm, laid flat dry with width of the bricks laid to the axis of the cable for protection of cable complete all as specified and as directed by the Engr-in-Charge

Supply and laying light grade GI pipe (ISI Marked) as cable protection to be fixed on wall / pole with necessary clamps as per existing or in road crossing as ordered of size 80 mm complete all as directed. ( Note :- Unit rate quoted is deemed to be inclusive of MS clamps required to be fixed on pole).

Supply and laying light grade GI pipe (ISI Marked) as cable protection to be fixed on wall / pole with necessary clamps as per existing or in road crossing as ordered of size 40 mm complete all as directed. ( Note :- Unit rate quoted is deemed to be inclusive of MS clamps required to be fixed on pole).

M& L for PCC (1:3:6) type C1 using 20mm graded stone aggregate as in coping and other similar bends including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and as directed.

Supply, installing, testing and commissioning our door type LT panel of 1500x1400x500 mm size, padestal mounted, CPRI approval factory made totally encloses, dust and vermin proof, double leaf shutter in front and single leaf shutter in rear side made of 3.15 mm thick CRCA sheet, framing with 50 x 50 x 6mm thick MS angle iron and legs of size 0.90mm long. duly fabricated and having proper locking arrangement in both front and rear door with 4 side slanting roof duly projected and painted to both internal and External surfaces with powder coating paint in heat process of sheet and suitable for 500 volts, 50 Hz, 3 phase 4 wire system and comprising with and including following accessories and mounted on PCC Plat form made out of PCC 1:3:6 100 mm thick, 1 Mtr all round the panel board complete with the following items:-

INCOMING:- (a) MCCB 4 pole, 415 Volts, 36 KA breaking cap rating 250 amps, adjustable thermal and adjustable magnetic including fixing accessories - 01 No (L&T Cat No - CM98065OOPO or equivalent model of as specified.)

BUSBAR:- (b) Aluminium busbar suitable for 315 Amp including insulator with nuts & bolts - 04 Nos.

Supply and fix in repair, Street light cable junction box made of polycarbonate, ''halogen free and weather proof', for outdoor installation (with metric knockouts for cable entry) IP-66 protection including short cable entry gland tread type with lock nut, four way bakelite terminal with brass studs and nuts, GI flat strip clamps of size 25mm X 3mm with bolts, nuts and washers for fixing with MCB one 06 Amps inside the junction box complete all as specified & as directed. (Make: HENSEL Cat No. KG 9002 or equivalent model of or equivalent model of as specified.)

Material and labour for earthing complete with galvanised steel plate electrodes of size 600x600x6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised iron wire 4 mm diameter as earth lead by means of nuts bolts check nuts & washers of GI with earth wire protected by galvanised iron pipe 15mm bore (Medium grade) for poles LT overhead lines etc all as directed including concrete pit with PCC (1:3:6) type C-I, precast RCC (1:1:5:3) type A-1 cover slab of size 55x55x7.5cm thick reinforced with 8mm dia TMT bars @ 15cm C/C both ways including providing one handle for lifting made out of 10 mm diameter mild steel round bar, funnel, wire mesh, 20 mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternate layers including necessary earth work in hard/dense soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion all complete as specified and as directed by the Engineer in Charge.

Material & Labour for point wiring (surface type) with 1.5 Sqmm (nominal cross sectional area) PVC insulated (FRLS) unsheathed single core multistranded copper conductor cable of working voltage 1100 volts grade conforming to IS-694 Pt I & II of 2000 drawn in and including 25 mm size PVC rigid non metallic casing capping (Double lock) with all casing capping fittings & accessories with PVC polycarbonate rectangular box of suitable size fixed with brass screws & cup washers, including 1.5 Sqmm (nominal cross sectional area) PVC insulated (FRLS) unsheathed single core multistranded copper conductor cable as earth continuity conductor connected to main switch/ 'DB's or common earth dolly for one fan point controlled by one 5 Amps one way switch complete all as specified and as directed. Note: Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.

Supply and fix ceiling rose, surface Bakelite, large type, three terminals 220/240 volts , white/ivory finish complete all as specified and as directed.

Supply & fix switch piano, flush type, SP, one way, 5/6 Amps 230 Volts, white/ivory finish complete all as directed.

S & F electronic dimmers, 450W, 250V flush type on the existing phenolic laminated sheet etc. as reqd.complete all as specified and as directed.

S & F Ceiling fan 230 V 1200mm sweep BEE 5 star rated complete all as specified and as directed.Make- Crompton Greaves Empower 50 or equivalent make as specified.

KAMLESH ENTERPRISE

M/S ANIL KUMAR THAKUR

DHARMINDER SINGH

M/S S. S CHETTRI AND SONS

RAAJ BANGAR

BIJAY MITTAL