ADDN/ALTN TO MNS MESS SERVENT QUARTERS ALONGWITH ALLIED WORKS AT 10 AFH AREA AT AF STN HASIMARA

Amount

Taking down chowkats with shutter (without taking off shutter from the frame) not exc. 1.5 Sqm each., complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n.exc. 4 Sqm each, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed.

S&F 105X60mm size factory made pressed steel frames for doors, made out of 1.25mm thick PBI sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

S&F 125X60mm size factory madepressed steel frames for doors, made out of 1.25mm thick PBI sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

S&F mild steel flat as in hold fast, wall ties, plain angle, clean for securing purline to wood trusses, conforming to Fe 290 Gde E-165, complete all as specified and directed.

S&F of 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type, on both sides, complete all as specified and directed.

S & F 30mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, wire mesh etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc., complete all as specified and directed. (Note: Wiremesh to be measured and paid seperately)

M&L for preparing new wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification & drawings, complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F of mild steel glazed window with mosquito proffing by provision of side hung shutter incl projecting type hinges with steel handle and steel peg stay complete with glazing bar and other window sde hung shutter incl projecting type hinges with steel handle and steel peg stay complete without glazing bar complete with glazing bars, dovetailed or welded ,complete all as specified and directed

S&F steel ventilator with top hung shutter, factory made confirming to IS, including hinges, steel peg stay, complete all as specified and as directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or fixed with tinned tracks including wooden beads, complete all as specified and directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint (1st grade quality) over a coat of red oxide primer, complete all as specified and directed.

S&F 300mm ordinary rat tail rod pattern springs including roller and roller plate of mild steel, complete all as specified and directed.

S&F 3.00mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square n exc 0.5 sqm in each pane, complete all as specified and directed.

S&F 3.00mm thick figured glass, pin head type and glazing with oil putty/wooden beads in square n exc 0.5 sqm in each pane, complete all as specified and directed.

S&F aluminium handles, cast type, anodised, 150mm size, complete all as specified and directed.

S&F of 150mm size aluminium anodised tower bolts, complete all as specified and directed

S&F of 200mm size aluminium anodised tower bolts, complete all as specified and directed

S&F 100mm long, butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed.

S&F 125mm long, butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified and directed.

S&F 300mm aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixingclips of sheet, cast or extrudedsections and fixing bolts andsliding bolts of extrudedsections or cast-aluminiumalloy and fixed, complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed..

M&L 15mm thick rendering in CM (1:6) on other than fair faces of brick work or concrete surfaces of wall, finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15mm thick in two coats (10mm+5mm each) on fair faces of brick work or concrete surfaces of wall in CM (1:4), mixed with integral water proofing compound top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement, complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item as supply only.)

M&L 5mm thick rendering in CM (1:3) on fair faces of ceiling surfaces, finished even and smooth (without using cement), complete all as specified and directed.

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification, complete all as directed

M&L for preparation of newly plastered wall surfaces and applying three coats of colour wash, complete all as specified and directed.

M&L for preparation of newly plastered ceiling surfaces and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old decorated surfaces of wall by scrapping down smoke soot, moulds moss and fluorescent salts and trading oil and greasing spots and applying two coats of colour wash, complete all as specified and directed.

M&L for preparation of old decorated ceiling surfaces and applying two coats of white wash, complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed.

M&L for complete removal of existing treatment from old plastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall, cornices etc and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm, complete all as specified and directed.

M&L for complete removal of existing treatment of old surfaces of wall, cornices etc and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior emulson primer applied @ 0.90 litre/ 10sqm, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position, not otherwise specifically provided for, complete all as specified and directed. (Note:-Reinforcement cut as required to facilitate demolition.)

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc and finished rough surfaces of concrete flat.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n. exc 10cm wide on rough finished surfaces of concrete, complete all as specified and directed.

S & F mild steel TMT bars 10mm dia (Grade Fe-500D), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia., or securing with clips, complete all as specified and directed.

S & F mild steel TMT bars 6mm to 8mm dia (Grade Fe-500D), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia., or securing with clips, complete all as specified and directed.

M&L for RCC nominal mix (1:1.5:3) type B1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for RCC nominal mix (1:1.5:3) type B1 (using 20mm graded crushed stone aggregate) as in chajjas, complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1( using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement including providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 Sqm in floor set and jointed in neat cement slurry and pointed in white or coloured cement of match over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 Sqm, as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match over and including 10mm thick rendering in CM (1:4), complete all as specified and directed.

Dismantling of floor, hearth or wall tiles including cement mortar bedding (but not backing) and removing rubbish off the premishes, complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350x250x7mm/450x350 x7mm thick each as in skirting or dado on vertical surfaces of wall, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4), complete all as specified and directed.

M&L for machine cut kota stone flooring 20-25mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and includging 15mm thick screed bed in CM (1 :6), complete all as specified and directed.

Taking down 20mm bore steel water tubing and connection from wall /ceiling surfaces including cleaning for re-fixing or removing from site of work, complete all as specified and directed.

S&F 20mm bore galvanised steel water tubing and connection, medium grade, with all fitting, fixed to wall or ceiling, complete all as specified and directed.

Re-fixing old steel tubing and connection 20mm bore in new or old position complete on wall/ceiling, complete all as specified and directed. (Note: Serviceable steel tubing obtained from taking down shall be re-used.)

Taking down 15mm bore steel water tubing and connection from wall /ceiling surfaces including cleaning for re-fixing or removing from site of work, complete all as specified and directed.

S&F 15mm bore galvanised steel water tubing and connection, medium grade, with all fitting, fixed to wall or ceiling, complete all as specified and directed.

Re-fixing old steel tubing and connection 15mm bore in new or old position complete on wall/ceiling, complete all as specified and directed. (Note: Serviceable steel tubing obtained from taking down shall be re-used.)

S&F in repairs 15mm bore, fancy type, chromium plated, stop valves, concealed type, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union with long shank and cup (concelled type), complete all as specified and directed.

S&F in repair vitreous china squatting pan ,"Orissa pattern" white, size 580x 440mm with integral foot rest, 'P' or 'S' trap, including connection to trap, and to flushing pipe, anti -syphonage pipe etc., complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back of size 550x 400 mm including PVC waste pipe 32mm bore, waste coupling including cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks, triple layered, (cylindrical vertical with closed top) ISI marked, confirming to IS 12701-1989, hoisted and fixed in position all as specified in SSR Part I (1000 ltr capacity) including 20mm Nipple suitable for HDPE water tank including 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed to 20mm bore pipe inculding dismantling of old water tank, complete all as specified and directed.

S&F PVC connection 15mm size of length 450mm with PTMT nuts, complete all as specified and directed.

S&F in repair CP pillar tap, 15mm bore, capstan head, screwed down high pressure with or without lettered “hot’ or “ cold” with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

S&F in repair 10 ltrs capacity low level valve less PVC syphonic action type flushing cistern white with inlet ball valve, float and handle and connection to pipes, complete all as specified and directed.

S&F in repairs of 15mm bore bib taps, cast copper alloy, chromium plated, fancy type, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in repair 15mm bore bib tap standard of PTMT any colour high pressure, screwed for iron pipe & fixed (minimum weight 90gms), complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick with plugs and wastes including in cement mortar onto dwart wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including waste pipe & coupling 32mm, complete all as specified and directed.

S&F in repairs 20mm dia brass chromium plated towel rail D type. 60cm long between flanges, complete all as specified and directed.

S&F in repair swivel shower rose 125mm size, brass, chromium plated, with long head arm for fixing with 15mm pipe, complete all as specified and directed.

S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed.

Demolition and breaking of internal dia of pipe 100mm bore / 75mm bore pipes of Salt glazed ware, PVC, AC or Reinforced concrete set in cement mortar, complete all as specified and directed.

S & F 110mm dia, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S & F 110mm dia PVC rain water pipes, single sockets, in any length with sealant rubber ring joints fixed to wall incl necessary MS flat iron clamps of size (40 x 4mm), complete all as specified and directed.

S & F 75mm dia, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F in repair of 110mm bore, PVC (SWR) bends of any radius, complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) junction, single, (single T) equal or unequal, complete all as specified and directed.

S&F in repair 75mm bore, PVC (SWR) bends provided with access door, of any radius, complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) junction, single, (single T) equal or unequal, complete all as specified and directed.

M&L in repairs 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solven cement, complete all as specified and directed.

S&F in repair of grating doom 100mm dia of PTMT (minimum weight 25gms), complete all as specified and directed.

S&F in repair 20mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipes, complete all as specified and directed.

S&F 20 mm dia curtain rod mild steel, chromium plated, decorative type, complete all as specified and directed.

S&F decorative type chromium plated bracket with ends/stops of rod and other accessories for fixing with 20mm dia curtain rod to wall, complete all as specified and as directed.

S&F 150mm length floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and as directed.

Cutting chases, pinning in. making good to facings where required and pointing in CM (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc., and making good, cutting not exc 10cm girth, complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as specified and directed.

Removing excavated materials to a distance exc. 250m but n. exc. 500m and depositing where directed, in any type of soil, complete all as specified and directed.

M&L for hardcore of gauge not exceeding 63mm of broken stone, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8) type D- 2, (using 40mm graded crushed stone aggregatet) as in floors, pavings or plinth protection etc., complete all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 20 to 25mm thick, with grey cement and pigments, jointed and pointed in neat cement slurry in floors over and including screed bed or bedding layer of CM (1:6), 15mm thick, complete all as specified and directed.

M&L for PCC (1:2:4) type B-1, (using 20mm graded crushed stone aggregate) as in sides of chequered tiles path, rounded or chamfered on edges, complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exc 1.5 metre in depth for foundation of pole / stay or cable trenches or for shafts, wells, cesspits, manholes etc, not exc. 10 Sqm on plan and not exc. 1.5m in depth and getting out in soft/loose soil , complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

M&L for PCC (1:2:4) type B-2, (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete etc., complete all as specified and directed.

M&L for fly ash brickwork, old size brick, straight or curved on plan exc 6m mean radius, built in CM (1:4), complete all as specified and directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate), cast in situ, in benching, coping and the like etc including weathering, slightly rounded or chamfered angles and throating, surface channel or drain including necessary form work, complete all as specified and directed.

M&L for 450mm bore RCC pipe class NP-2, laid in trenches, laid and jointed complete with collars, complete all as specified and directed.

M&L for 100mm thick PCC (1:2:4) type B2 (using 40mm graded crushed stone aggregate) in sub-base, floors and pavings etc, finished the surfaces even and smooth with using extra cement, complete as specified and directed.

Returning filling in incl spreading, leveling watering and well ramming in layers not exceeding 25cm in soft/loose soil, complete all as specified and directed.

M&L for random rubble walling, uncoursed, well bonded, bedded and solidly hearted, built in CM (1:6) on sloping face of road, complete all as specified and directed.

Excavating over areas n. exc. 1.5m deep and getting out in soft/loose soil, complete all as specified and directed

S & F for MS round bar Fe 410 W Gde 250 A 10mm dia and over for rungs, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as specified and directed.

M & L for precast RCC (1:2:4), type B1 (using 20mm graded crusged stone aggregate) as in cover slab, shelves and similar articles with plain faces including necessary form work and set in CM (1:6), complete all as specified and as directed. Note: Reinforcement shall be measured and paid separately.

M & L for 150mm bore reinforced concrete pipes, class NP2, laid and jointed with collars, complete all as specified and directed.

M & L for PCC (1:3:6) type C-2, (using 40mm graded stone aggregate) as in concrete bed to drain pipe including packing under and haunching against sides of pipes after they are laid and tested for 150mm bore pipe, complete all as specified and directed.

M & L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms moulds, mitred/stopped ends etc, complete all as specified and directed.

M & L for PCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in surface channel or drains including necessary form work, complete all as specified and directed.

Demolition of brick work or stone masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

Dismantling brick or brick tiles laid bedded and pointed in any type of mortar, complete all as specified and directed.

M&L flyash bricks, old size, laid on edge and bedded and jointed in cement mortar (1:6) and pointed in CM (1:3) in drains, channels, kerbs etc using old size bricks, complete all as specified and directed.

M&L flyash bricks, old size, laid flat and bedded and jointed in cement mortar (1:6) and pointed in CM (1:3) in drains, channels, kerbs etc. using old size bricks, complete all as specified and directed.

All as per item No. 113.00 here-in-before but except bricks, complete all as specified and directed. Note-(i) Bricks obtained from demolition shall be re-used. (ii) The quoted rate shall deemed to be included for cleaning of old bricks obtained from demolition.

Racking out joints/pointing to brick work in drain including keyed pointing to brick surfaces in CM (1:4), complete all as specified and directed.

Taking down carefully copper/aluminium point wiring complete (light,fan, plug point & power complete alongwith fittings (switches, ceiling roses, tube light fittings, bulk head fitting, regulator, sockets main switches, DB removing materials to store & making good of disturb surfaces of wall/floors etc, complete all as specified and directed.

M&L for point wiring complete as specified with 1100 V grade with 1.5 Sqmm single core PVC insulated unsheathed FRLSH cable, copper conductor multistranded passing through including concealed PVC conduit not less than 20mm dia and its accessories with sunk cast iron/pressed steel terminal boxes of size 1.6mm thick including PVC insulated FRLSH unsheathed stranded copper conductor of size 1.5 sqmm as earth wire connected to common earth dully for one light point / one fan point/one bell/buzzer point controlled by one, one way swtich, complete all as specified and directed. Note: - (i) Unit quoted rate shall deemed to be included for cutting chases for conduit and sinking for boxes and making good of wall floors etc as per exsting.

All as per item No 117.00 here-in before but one 5 Amp 5 pin socket outlet point on same board with other switches including earth wire, complete all as specified and directed.

All as per item No 117.00 here-in before but on independent board, complete all as specified and directed.

All as per item No 117.00 here-in before but with 4.0 Sqmm PVC copper multi stranded cable FRLSH type for one 15 Amp 6 pin socket outlet point including PVC cable 4.0 Sqmm FRLSH type copper multi stranded conductor as earth wire, complete all as specified and directed.

S&F switch piano flush button 5 Amp single pole one way 230 volts white finish, complete all as specified and directed.

S&F bell push, 230 volts, white finish, complete all as specified and directed.

S&F switch socket outlet, flush type, 2 in 1,3 pin 5 Amp 230 volts white/ivory finish, complete all as specified and directed.

S&F switch socket multipurpose, flush type, 2 in 1 type (3 and 3 pin) 5/16 Amps, 230V, AC white/ivory finish, complete all as specified and directed.

S&F bell type AC, 230 volts, single phase, complete all as specified and directed.

S&F ceiling rose of size 65 x 50mm surface bakelite 240 Volts, three terminal, complete all as specified and directed.

S&F and connecting up fan regulator electronic on existing socket type 230 volts, suitable for ceiling fan 1200/1400mm sweep, complete all as specified and directed.

S&F LED lights fitting 1x 20 W, 220V,AC , with driver, LED rod complete connecting up with 2/3 core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F LED lights fitting 1x 10 W, 220V,AC ,with driver, LED rod complete connecting up with 2/3 core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed.

S&F MCB distribution board (DB) TPN with sheet metal encloser, double door, IP 43 protection, 240 volts, 04 way, single pole and neutral, with 200 Amps rated busbar (as per OEM), neutral link for fixing MCBs/Isolators including taking down old unserviceable MCB DB of any description, completes all as specified and directed.

S&F MCB distribution board (DB), SPN with sheet metal encloser, double door, IP 43 protection, 240 volts, 04 way, single pole and neutral, with 200 Amps rated busbar (as per OEM), neutral link for fixing MCBs/Isolators including taking down old unserviceable MCB DB of any description, completes all as specified and directed.

S&F MCB SP 6 to 32 Amps, 240V, 10 KA, 'B' curve, including connection of testing, completes all as specified and directed.

S&F MCB SPN 6 to 32 Amps, 10 KA, 'C' curve, complete all as specified and as directed.

S&F MCB 4 pole, 63 Amps, 10 KA, 'C' curve, complete all as specified and as directed.

M&L for submain wiring wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLSH type, cables 4 Sqmm drawn in and including heavy duty PVC conduit not less than 20mm size including 4 Sqmm 1100 Volts grade, FRLSH type, PVC insulated unsheathed multistranded flexible copper conductor cable as continuous earth wire and connecting to common earth dolly including taking down old sub-main wiring of any size, complete all as specified and directed. Note:-(a) Three runs of cable shall be measured as one length of sub main. (b) PVC conduit and its accessories shall deemed to be included in the unit quoted rate.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including taking down old ceiling fan, any type and deposited to AGE E/M store yard, completes all as specified and directed.

S&F exhaust fan, steel body AC, single phase, 230V of size 300mm sweep with, blades, and frame and louvers including cutting wall for fixing exahaust fan of size 300mm sweep and making good the opening in CM (1:3) or PCC (1:2:4) type B1 as required at site including taking down old exhaust fan, any size and deposited to AGE E/M store yard, completes all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 4 core including taking down old unserviceable UG cable of any size, complete all as specified and directed.

Supply and laying double walled corrugated (DWC) HDPE duct pipe of 40mm dia conforming to IS, approved colour complete with fittings for cable protection including cutting to the existing wall and drawn into wall for laying of cable, complete all as specified and directed.

Removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point in any type of soil, complete all as specified and directed.

M &L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6.3cm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized wire of size 4mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part -1, including necessary excavation and earth work, P.C.C (1:3:6) type C-1 with 50mm thick Pre-cast R.C.C. (1:2:4) type B1 cover slab (reinforced with 8mm dia deformed bar 15cm C/C both ways and suitable handle of 10mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15cm compacted thickness all around the earth electrode, with funnel and 20mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, Gl earth wire protected by 15mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion including dismantling of old unserviceable earthing of any descriprtion, complete all as specified and as directed. Note : Proper earthing pit should be provided with pit cover.

S&F LED street light fittings 35 watt 230 v AC outdoor type with high pressure dia cast aluminium housing and heat-resistant complete with driver, lamp bracket with impact and corrision resistant, IP 65/66 protection, complete all as specified and directed.

S&F 25mm dia CPVC pipes SDR-13.5 & plain CPVC, SDR 11, fittings complete on wall/floor/roof terece with necessary saddle/clamps including all necessay fittings, like elbow, tee, socket, reducer, bushings, end caps, End plugs, etc and with CPVC solvents cement including taking down old unserviceable pipes of any type, complete all as specified and directed.

S&F CPVC ball valve of size 25mm dia suitable for CPVC pipe including necessary fittings and taking down old unserviceble ball valve of any description, complete all as specified and directed.

Note: An amount of Rs.45,298.50 on account of Credit Schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

CONSTRUCTION SHELTER

M/S. VINITA CONSTRUCTION

M/S ASHOK ENTERPRISE

M/S SANMILAN NANDI

M/S ANIL KUMAR BAUL

SHRI SURAJIT SIKDER

M/S MANODEEP CONSTRUCTION