Constn. of crematorium near Naba Kalyan Sangha Pachar Dokan with 12ft. Tin Shed room under Balarampur G.P. within Tufanganj-I P.S. SL7

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work). With earth obtained from excavation of foundation.

Filling in foundation by carried earth arrainged by the contractor within a radius of 3 km

Single brick flat soling of picked jhama brick including ramming and dressing bed to proper level and filling joints with powdered earth or local sand.

Cement concrete with graded jhama khoa (30 mm size) excluding shuttering In ground floor and foundation. (a) 1:3:6 proportion

Ordinary cement concrete ( mix 3:1.5:1) M-20 with graded stone chips (20mm down) excluding shuttering and reinforcement,if any in groundfloor. B) River bazree.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction. for works in foundation,basement and upto roof of ground floor / upto 4.0m. i. Tor steel / Mild steel (TATA/SAIL/RINT )

Hire and labour charge for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, columns, lintels curved or staight including fitting fixing and striking out after complection of works. 25 mm. to 30 mm. thick wooden shuttering as per decission & direction of E-I-C

Brick work with 1st class bricks in cement mortar (1:4) (a) In foundation and plinth

125mm thick Brick work with 1st class bricks in cement mortar (4:1) in Ground floor

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints or roughening of concrete surface, including throating, nosing and drip course where necessary (ground floor). 20 mm. thick plaster (with 4:1 cement mortar) in groung floor.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints or roughening of concrete surface, including throating, nosing and drip course where necessary (ground floor). 15 mm. thick plaster (with 4:1 cement mortar) in groung floor.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints or roughening of concrete surface, including throating, nosing and drip course where necessary (ground floor). 10 mm. thick plaster (with 4:1 cement mortar) in groung floor.

Neat cement punning about 1.5 mm. thick in wall, dado, window, sills, floor, drain etc.

Applyingdecorativecementbasedpaintofapprovedqualityafter preparingthesurfaceincludingscrapingthesamethoroughly (plasteredorconcretesurface)aspermanufacturer'sspecification. InGroundfloor:

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc.

Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of150gramspersq.metre(followedbycolourcoatedonbothside) steelsheetworkhavingminimumyieldstrengthof550Mpaof trapizoidalprofileofapprovedmake(excludingthesupporting framework)fittedandfixedwith55mm&25mmselftapping screw,EPDMWasher16mmdia&3mmth.washeretc.complete with150mmendlapandonecorrugationminimumsidelap. (Paymenttobemadeonareaoffinishedwork).

Priming one coat on steel or other metal surface with synthetic enamel/oil bound prinmer of approved quality including smoothening surfaces by sand papering etc.

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand parpering etc. in cluding using of approved putty etc. on the surface , if necessary. On steel or other metal surface: With super gloss (hi-gloss) Two coats (except white in shade )