CA NO GE/GUR-/NIT-02/2020-21 CONSTN OF FSS ROOM AT RADAR, REPAIR/RENOVATION TO BLDG NO P-60, IMPROVEMENT TO CIVILIAN QUARTERS, RENOVATION TO TOILET AT FIRE SECTION ,PROVN OF COVERED PARKING SHED AT SMQ AREA AND PROVN OF XBIS ROOM AT MGR AT AF STN AR

Amount

B/R Works:- Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth; for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc not exceeding 10 Sqm on plan and not exceeding 1.5 M in depth and getting out in hard/dense soil complete all as specified and as directed.

Ditto all as per item No 1.00 described here-in-before but in hard rock

M&L for cement concrete (1:5:10) type E2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for brickwork with sub class old size ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and as directed.

M&L for providing cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in lintels upto 1.5 M clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including formwork complete all as specified and as directed.

M&L for providing reinforced cement concrete (M-25) Design Mix (using 20 mm graded crushed stone aggregates) as in foundations including rafts, column footings, plinth beams, etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix (using 20 mm graded crushed stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix (using 20 mm graded crushed stone aggregates) as in columns, pillars, piers, posts and struts etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix (using 20 mm graded crushed stone aggregates) as in beams, cantilevers, bressummers, lintel over 1.5 span complete all as specified and as directed

Ditto all as per item No 9.00 described here-in-before but as in chajjas.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work not exceeding 200mm thick horizontal or sloping for fair finished surfaces of concrete complete all as specified and as directed.

Use and waste of form work to chullah hoods, chajjas trough and similar items incl edges complete all as specified and as directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc complete all as specified and as directed.

Use and waste of form work to sides of concrete foundations, footing, bases of columns, raft beams, sides and soffits of plinth beams and similiar works etc complete all as specified and as directed.

Use & waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs n exc 20cm wide and sides of RCC/ PCC bends in walls, horizontal or sloping and similar work exceeding 10cm but n exc 20cm wide for fair finished surfaces complete all as specified and as directed.

Use & waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs and sides of RCC/ PCC bends in walls, horizontal or sloping and similar work exceeding 5cm but n exc 10cm wide for fair finished surfaces complete all as specified and as directed.

M&L for providing cement plaster 15 mm thick in cement mortar (1:4) using water proofing compound as in bearing plaster under RCC slabs complete all as specified and as directed.

M&L for MS TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Ditto all as per item No 18.00 described here-in-before but 6 to 8mm dia bars

Ditto all as per item No 18.00 described here-in-before but 6 mm dia and over up to 10mm dia as in stirrups

Supply only water proofing compound complete all as specified and as directed.

S&F PVC (SWR) rain water pipe 110mm outer diameter, single socketed in any length fixed to walls complete all as specified and as directed.

S&F PVC (SWR) bends any radius 110 mm dia fixed to PVC pipes complete all as specified and as directed.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, size of door frame 125x60 mm complete all as specified and as directed.

M&L for PCC (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) as in filling of pressed steel door frames and as in hold fast blocks incl all form work complete all as specified and as directed.

M&L for factory made flush shutters 35 mm thick, ISI marked, solid core construction, with block board core and plywood face panels, commercial type with hot processed lamination 1.50 mm thick on both faces, of approved shade, colour and 35mmx12mm 2nd class teak wood lipping all round and exposed edges finished with two coats of polyurethene coat (PU Coat) of approved make over a coat of primer complete all as specified and as directed.

S&F aluminium alloy, anodised, sliding door bolt 300mm size with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy and fixed complete all as specified and as directed.

S&F Butt hinges 100mm size medium weight cold rolled mild steel and fixed complete all as specified and as directed.

S&F aluminium handles cast type 125mm size anodized and fixed complete all as specified and as directed.

S&F door closer hydraulically regulated designation No 3 universal type cast iron body suitable for door shutters 850mm to 1000mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and as directed.

S&F aluminium anodized door stopper twin legged with rubber shoe and fixed 75mm size complete all as specified and as directed.

M&L for 40 mm thick cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in flooring finishing even and smooth using extra cement complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20 mm thick in slabs of size as approved by GE over 20mm thick cement screed base in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and as directed.

Ditto all as per item No 33.00 described here-in-before but as in skirtings etc laid over 10mm thick rendering in CM 1:4

M&L for 15 mm thick cement plaster in cement mortar 1:4 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick cement plaster in cement mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 5 mm thick cement plaster in cement mortar 1:3 as on ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for machine cut granite stone slab 20-25mm thick black fixed on shelves top over 20mm thick cement screed base in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and as directed.

Removing surplus excavated materials (soil) to a distance not exceeding 50 metre and depositing where directed at a level not exc 1.5 metres above the starting point complete all as specified and as directed.

S&F prelaminated particle board 12mm thick exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws as in pelmet boxes incl fixing arrangement complete all as specified and as directed.

S&F venetian blinds with 100mm wide flaps of approved shade vertical type having tilting and sliding arrangement by means of nylon threads made to size fixed with aluminium channel powder coated and MS clamps or as per manufacturers instructions complete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying three coats of white lime washing on ceiling surfaces complete all as specified and as directed.

Material and labour for preparation of new decorated surface of walls including applying cement based wall care putty (Birla care/JK wall putty) 1mm thick (average) and applying two coats of weather proof exterior emulsion paint (any colour) paint over a coat of primer of same manufacturer to achieve uniform and smooth surface using roller brush complete all as per manufactures instructions and as directed. Make: Asian (Apex ultima)/ Berger (Weather coat)/Nerolac (Excel total)

Material and labour for preparation of new plastered surfaces and applying two coats of oil emulsion distemper on walls including chalk whitening preparatory to distempering and a priming coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of new untreated wooden surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new untreated steel surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C1 (using 20mm graded aggregate) 75mm thick as in plinth protection surface finished even and fair without using extra cement including joints filled with bitumen mastic complete all as specified and as directed.

M&L for 100 mm thick cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregates) as in sub base of flooing etc complete all as specified and as directed.

M&L for sand filling under floor or in foundations including watering and consolidation complete all as specified and as directed.

S&F aluminium anodized door frame and fully glazed shutter divided in to two glazed panels including aluminium anodized snap beading and rubber gasket / lining for fixing of glass as directed. The frame shall be fixed with aluminium anodized bolt by drilling in the existing wall and with thrust bolt of suitable size all as directed. The frame and shutter will be made out of the following sections and fittings: (a) Aluminium anodized door frame 100mmx44mmx1.6mm fixed with aluminium board and thurst bolt in walls by drilling as directed Aluminium anodized top, sides and lock rails of shutter section 81mmx44mmx1.6mm (b) Aluminium anodized bottom rail of shutter section 112mmx44mmx1.6mm (c) Brass six lever dead lock suitable for aluminium doors manufactured by Harrison Locks or Godrej as approved – 01 No for each door (d) Aluminium anodized tower bolt 200 mm long size Make Classic or Argent – 02 Nos in each door (e) Aluminium anodized fancy handle 250mm long Make Classic or Argent – 02 Nos in each door (f) Glass pane shall be 5.5mm thick tinted glass of size as required (g) Floor spring hydraulic heavy duty and pivot arm Make Everite/ Sandhu – 01 No for each door

S&F aluminium anodized window frame 100mmx44mmx1.6mm fixed with aluminium board and thurst bolt in walls by drilling as directed. (a) Aluminium anodized window shutter styles and rails 44mmx44mmx1.6mm (b) Aluminium anodized butt hinges 04 Nos in each window 75mm long ISI marked (c) Aluminium anodized tower bolt 200 mm long size Make Classic or Argent – 02 Nos in each shutter (d) Aluminium anodized cast type handles Make Classic or Argent – 01 No in each shutter (e) Aluminium anodized hook and eye 150mm long 01 No for each shutter (f) Glass pane shall be 5.5mm thick tinted glass of size as required

S&F aluminium anodized fixed partition fully glazed divided into glazed panels not exceeding 900mm centers both ways including aluminium anodized snap beading and rubber gasket / lining for fixing of glass as directed. The frame shall be fixed with aluminium anodized bolt by drilling in the existing wall and floor with thrust bolt of suitable size all as directed. The frame of partition shall be made out of the following sections and fittings: (a) Aluminium anodized frame 63mm x 38mm x 1.6mm fixed with aluminium board and thurst bolt in walls by drilling as directed. (b) Panels shall be of 12mm thick pre laminated particle board both side decorative Make Novopan/ Kitlam/ Bhutan Board

S&F false ceiling with exposed GI system using “SILHOUETTE XL 15 mm (Nominal) designer Grid "Armstrong" white or Global white with black reveal and 600 x 600 x 15 mm thick prime fine fissured micro look white/coloured tiles (superfine 15mm/silhouette). Making necessary framework for AC ducting, if any and necessary cutouts for diffusers and light fittings, taping and finishing to proper line & level complete all as per manufacturer’s instructions and as directed.

Supply & fixing prelaminated particle board 18/19 mm thick, exterior grade with one side decorative choice lamination and other side balancing white lamination fixed with screws to timber frame as in cupboards, shutters, shelves, pelmet etc. including fixing 18 mm wide 6 mm thick beading of Ist class HW (Teak) all around complete all as specified and as directed.

S&F plain fillets square, rectangular or triangular in section, 2nd class hardwood of sectional area exc 13 & n exc 25 sqcm, clean sawn, wrought finished secured with screws complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; and similar work conforming to Fe-290 Gde-E-165, complete all as specified and as directed.

M&L for rolled mild steel plates (Plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment complete all as specified and as directed.

M&L for ply wood, 6 mm thick, 7 No of ply, grade BWR, type B, fixed with screws to timber frame work complete all as specified and as directed.

S&F Continuous (piano) hinges with width of flap 30 mm mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F 100 mm size hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and as directed.

M&L for second class hard wood wrought as in scantling framed complete all as specified and as directed.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

S&F brass type handles 100 mm size cast type polished bright complete all as specified and as directed.

S&F brass 4 lever lock, cupboard grade I size 75 mm complete all as specified and as directed.

M&L for vitrified ceramic tiles double charged 10 mm thick (square/rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15 mm thick cement screed bed in CM 1:4 complete all as specified and as directed.

Ditto all as per item No 66.00 described here-in-before but in skirting/risers/dados etc. over and including 10 mm thick rendering in CM 1:3 complete all as specified and as directed

M&L for providing and fixing PVC sheet wall (prelam wood veneers design) panelling of thickness 5 mm consisting of panels having size 1220 mm X 2440 mm stuck on internal framework of 50 mm wide strips of 5 mm thick PVC sheet, the strip should have in there centre a groove of 6 mm thick width and 1 mm depth for sinking the head of the screw used to fix the strips to the wall vertically at an equal interval of 10 inches between two pvc strips. The PVC sheets shall be fixed to the wall using 65 mm long MS screws through the groove in the strip by using PVC fasteners; the distance between two screws shall not be more than 200 mm, a groove of 12 mm may be left at the joint of the panel for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a strip of 5 mm thick PVC sheet of width 5 mm thick PVC sheet of width 75 mm feathered at the edge shall be stuck at the place where two panels are jointed using solvent compound complete all as specified and as directed.

M&L for preparation and cleaned to plastered/ concrete surfaces of roof applying the under mentioned course of roof treatment as given below :- (a) Applying evenly compactible primer @ 0.4 litre per Sqm over concrete/ plastered roof surfaces. (b) Applying a tack coat of industrial bitumen 85/25 grade (ISI marked) @ 1.2 kg/Sqm. (c) Laying of membrane sheet of weight not less than 3.6 kg/Sqm with minimum longitudinal end over laps of 100mm and horizontal side laps of 75mm and joints finally thermo-fused with help of LPG flames. Membrane sheet laid over a tack of industrial bitumen 85/25 as specified here-in before. Note:- (i) Membrane sheet also laid along the parapet upto 30cm height & inserted inside the groove & laid over a coat of bitumen as specified here-in-before. The groove shall be closed with CM (1:3) mortar nothing extra shall be admissible on this account (ii) WPC shall be measured & paid under pecified item of this Schedule. Nothing shall be entertained on this account. (iii) Contractor shall submit guarantee for 10 years from the date of completion of work. (iv) The amount against guarantee period for roof treatment shall be retained from the contractor due’s or contractor may furnish a fixed deposit receipt in favour of GE as issued by Nationalize Bank. (v) Amount of security deposit against the guarantee period for roof treatment shall be calculated as per the scales laid down for calculating Individual Security from total amount of roof treatment.

M&L for first quality, non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and laid over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and as directed.

M&L for first quality, non skid ceramic coloured joint free tiles, 7 to 8 mm thick (square or rectangular) area of each tile exc 0.18 Sqm but n.exc 0.38 Sqm, laid in floors set and jointed with neat cement slurry @ 3.00 kg/Square Metre laid over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and as directed.

M&L for first quality coloured glazed ceramic tiles, fixed in pattern of different colour including border of high lighter concept from Make:- Somani/Kajaria/Johnsons or as approved by GE of size 300x 450 x 7mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid over and including 10 mm thick rendering in cement mortar (1:3), including pointing in white cement with pigment to match the shade of tiles, complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks 1000 Litres capacity (cylindrical vertical with closed top) triple layred hoisted and fixed in position complete all as specified and as directed.

S&F ball valves 20mm size high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and as directed.

S&F stop valves cast copper alloy fancy type 20 mm dia screwed down, screwed both ends for iron pipes or for unions and fixed complete all as specified and as directed.

S&F galvanized steel water tubing 20 mm bore medium grade including all fittings and fixed to walls and ceiling or laid in floors etc complete all as specified and as directed.

Ditto all as per item No 76 described here-in-before but 15mm bore size

S&F pillar tap 15mm size cast copper alloy chromium plated fancy type screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipes complete all as specified and as directed..

S&F bib taps cast copper alloy 15mm size chromium plated fancy type with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F wash hand basins vitreous china flat back 550x400mm size white including CP waste grating 32mm size, PVC waste pipe 25mm bore heavy duty, chain and plug and porcelain stopper, brackets of MS angle 35x35x6mm size complete all as specified and as directed. Note: Pillar tap shall be measured and paid for separately

S&F Wash down water closet pan (pedestal pattern) white incl, PVC Flushing cistern 10 Liters capacity low level as specified, PVC waste pipe suitable to joint flushing cistern to water closet fixed on existing P or S trap complete all as specified and as directed.

S&F Cast iron floor trap 75 mm bore including 100 mm round CP brass round grating including jointing to waste pipe in run lead and set in cement concrete 1:2:4 type B1 complete all as specified and as directed.

S&F Cast iron soil waste and vent pipes 100mm bore size sand cast in any length with or without ears with cement joints laid in floors complete all as specified and as directed.

S&F Cast iron soil waste and vent pipes 75mm bore size sand cast in any length with or without ears with cement joints laid in floors complete all as specified and as directed.

S&F Cast iron soil waste and vent pipes 50mm bore size sand cast in any length with or without ears with cement joints fixed to walls complete all as specified and as directed.

S&F Cast iron branch piece 100 mm bore size with oval access door single (equal or un equal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed by Engineer in charge.

S&F Cast iron bends any radius 100mm bore size with Ducks foot or heel rest complete all as specified and as directed.

S&F Cast iron bends any radius 75mm bore size with Ducks foot or heel rest complete all as specified and as directed.

S&F Cast iron bends any radius, diminishing pieces or tapers 100mm bore size complete all as specified and as directed.

S&F Cast iron bends any radius, diminishing pieces or tapers 75mm bore size complete all as specified and as directed.

Ditto all as per item No 91 described here-in-before but with oval access door

S&F Cast iron cowls 50mm size complete all as specified and as directed.

M&L for extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joints, size of pipe 100mm complete all as specified and as directed.

M&L for extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joints, size of pipe 75mm complete all as specified and as directed.

S&F Salt glazed stone ware gulley traps 150x150mm size square mouthed type ‘P’ complete all as specified and as directed.

M&L for Salt glazed stoneware drain pipes 150mm size laid in trenches and jointed complete all as specified and as directed.

M&L for cement concrete (1:3:6) type C2 (using 40mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes 150mm bore size after they are laid and tested complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete and foundations of manholes etc complete all as specified and as directed.

Cutting into existing manhole for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or ¾ section) in cement concrete (1:2:4) type B-1 smooth finished and reforming benching as required for 150mm internal dia of pipe complete all as specified and as directed.

M&L for Pre cast cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) set in cement mortar (1:4) as in manhole covers, shelves and similar items complete all as specified and as directed.

M&L for RCC NP3 150 mm dia pipes laid in trenches and jointed complete all as specified and as directed.

M&L for two coats of weather proof exterior emulsion paint over a coat of primer on wall surfaces including preparation of newly plaster surfaces etc complete all as specified and as directed.

S&F steel work in tubular trusses, rafters and posts etc including special shaped washer etc. complete using ERW or induction butt welded Squre/ Rectangular tubes conforming to IS-1161-1979 (Grade ST-240) complete all as specified and as directed.

M&L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for 20mm thick granite stone (table rubbed) for wall lining (veneering to wall) machine cut laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing over a 12 mm thick in cement plaster 1:3 on fair faces of brick work or concrete surfaces using marble dust with admixture complete all as specified and as directed.

S&F 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F 150 mm long anodised aluminium handle, cast type complete all as specified and as directed.

S&F 300 mm long mild steel sliding door bolt, bolt type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth; for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc not exceeding 10 Sqm on plan and not exceeding 1.5 M in depth and getting out in soft/loose soil complete all as specified and as directed.

Spreading and levelling of earth in layers not exceeding 25cm thick and well ramming including watering as required complete all as specified and as directed.

M&L for broken bricks hard core of gauge not exceeding 63mm, deposited, spread levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete, sub base complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M&L for damp proof course in cement concrete (1:2:4) type B0, 40mm thick to horizontal or vertical surfaces including necessary form work complete all as specified and as directed.

Applying evenly a coat of blown type bitumen at the rate of 1.50 Kg per Sqm and blinding with clean dry sand @ 0.05 Cum per Sqm complete all as specified and as directed.

Cutting chases, pinning in brick walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc; and cuttings chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

M&L for forming jambs, etc; to opening (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete built in cement mortar 1:4 complete all as specified and as directed.

Taking down chowkats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each complete all as specified and as directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

M&L for machine cut Kota stone slab flooring 20 – 25mm thick over cement screed base 15mm thick in cement mortar 1:4, over PCC 1:2:4, type B0 25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Taking down cement plaster on brick wall including racking out joints, hacking for keys scrubbing down with water complete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying three coats of white lime washing on wall surfaces complete all as specified and as directed.

M&L for applying two coat of cement base paint on new plastered surfaces of walls including preparation of surfaces complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane complete all as specified and as directed.

Taking down steel tubing 15mm bore and connections including cleaning for refixing complete all as specified and as directed.

Ditto all as per item No 127.00 described here-in-before but 20mm bore

S&F rotational moulded polyethylene water storage tanks 500 Litres capacity (cylindrical vertical with closed top) triple layred hoisted and fixed in position complete all as specified and as directed.

S&F bib taps 15mm bore cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and as directed.

S&F 15mm bore stop valve, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and as directed.

S&F stainless steel sink with drainage board made out of 1.00mm thick sheet for kitchen with plug, washers, waste fittings, waste pipe, cast iron cantilever brackets, over all size 915mm x 460mm with bowl size 410mm x 330mm x 160mm with waste pipe PVC 40mm dia (ISI Marked) complete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of Reinforced cement concrete (reinforced cut as required to facilitate demolition) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

S&F plate rack of stainless steel, sheet 1mm thick for kitchen overall size 900x900x250 mm, fixed with plugs and washers on wall complete all as specified and as directed. Make :- Pryag or equivalent

S&F for 35 mm thick second class hard wood plain framed factory made panelled shutter (two panel) with lock rail and panel 9mm B.W.P or 12 mm veneered particle board with commercial veneering on both faces . The size of rail and style as per IS 1003/SSR Part -I. Make-Jain Doors Pvt Ltd Sonipat/ Chandigarh Timber Products, Patiala / PIONEER TIMBER PRODUCTS CHANDIGARH

S&F 0.63mm Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating complete all as specified and as directed.

M&L for 25 mm thick cement concrete (1:2:4) type B0 (using 12.5 mm graded stone aggregate) as in base of floor finish finished even and rough to receive floor bedding complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and as directed.

S&F 15mm bore concealed stop cock, regular body with adjustable wall flange, fancy type, chromium plated cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and as directed.

S&F 15mm bore angular stop cock with wall flange, fancy type cast copper alloy with capston head, chromium plated, screwed down high pressure and fixed for iron pipe with C.P. brass connection pipe with union nuts complete with C.P. brass flange including cutting and making good the walls where ever required complete all as specified and as directed.

S&F bib taps long body 15mm bore cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and as directed.

S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipes 15mm bore complete all as specified and as directed.

Ditto all as per Item No.145 described here-in-before but 20mm bore

S&F soap dish brass chromium plated, fixed to plugs with brass chromium plated screws complete all as specified and as directed.

S&F brass chromium plated tubular towel rail 20mm dia “D” type 60 cm long between flanges including brackets complete all as specified and as directed.

S&F in repairs Ist quality vitreous china wash basin, white, flat back, size 550x400mm, PVC connections suitable for hot and cold water, bottle trap (with internal partition) 32 mm size with 300mm &190mm long wall connection pipes & wall flange and fixing with brackets/ bolts including cutting and pinning in etc complete all as specified and as directed.

S&F in repairs 15 mm bore pillar tap cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

Supply and fix in repairs Cast iron floor trap with dia of outlet 100 mm, with CP grating hinge type in kitchen and other situation including PCC 1:2:4 type B1 for setting the trap and jointing to waste pipe including taking out old floor trap, complete all as specified and as directed.

S&F in repairs vitreous chinaware water closet white squatting pan orissa pattern long pan size 580 mm x440mm white with ‘P’ or ‘S’ trap, connecting to trap and to flushing pipe etc complete with foot rest of size 580x440 mm (Jointed with epoxy raison with glazed trap) incl provn of lime concrete bedding complete all as specified and as directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and as directed.

Cutting hole in brick wall built in cement mortar exceeding half brick but not exceeding one brick and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4, type B-1 complete all as specified and as directed.

M&L for brick masonry with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius, built in Cement Mortar (1:4) complete all as specified and as directed.

Material and labour for preparation of old plastered surfaces of walls by washing, rubbing down and stopping of surface and applying two coat of white lime wash complete all as specified and as directed.

Material and labour for preparation of old plastered surfaces of ceiling by washing, rubbing down and stopping of surface and applying two coats of white wash complete all as specified and as directed.

Material and labour for removal of existing treatment completely on walls and preparaing the surface for applying two coats of oil bound distemper to achieve uniform and smooth surface by roller brush over and including cement based wall care putty 1mm thick (average thickness) complete all as specified and as directed. Make of oil bound distemper : Asian paints (Tractor)/ICI Dulux/Nerolac paints/Berger (Bison)

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded coloured PVC ’C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of single side prelaminated PVC sheet to be fitted in the MS frame welded/ sealed into the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification complete all as specified and as directed.

S&F factory made PVC solid door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of 5 mm thick plain colour PVC sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided throughout the frame and fixed to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical member & minimum 02 Nos. for horizontal member), complete all as specified and as directed.

S&F Vitreous China urinals, flat back large pastal colour Make : Hindware Cat part No 60002 complete including spreader and providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified.

M&L for powder coated (thickness of powder coating not less than 50 micron) anodised aluminium frame for doors , windows, ventilators with one or more rebates with and including weight of joining cleat for fixing etc complete all as specified and as directed

M&L for Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazingclips, rubber packing, anodisedaluminium snap beading, screws etc. complete all as specified and as directed

S&F in repair PVC valveless, syphonic action type, flushing cistern of 10 litres capacity, low level, white, with inlet, ball valve, float & handle including brackets etc complete all as specified and as directed.

Hacking out old broken glass of any thickness, size, quality or description from n exc. 0.50 sqm in each pane metal frame glazed with oil putty or fixed with beads including punching or out old glazing pins, spring clips, complete all as specified and as directed.

S&F 4mm thick sheet glass ordinary quality & glazing with oil putty in square n exc. 0.50 sqm in each pane complete all as specified and as directed.

M&L for chequered cement concrete tiles 250mmx250mmx20mm thick with grey cement and pigments (as approved), set and jointed and pointed in neat cement slurry in floors, laid over 15mm thick cement screed bed of CM (1:6), complete all as specified and as directed.

S&F chromium plated brass shower rose 125 mm dia with swivel joint complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth, in layers not exceeding 25cm thick, watering, and removing surplus spoil to a distance not exceeding 50m and making good surface complete all as specified and as directed.

M&L for 150 mm thick Cement Conrete (1:2:4) type B–1 (using 20mm graded stone aggregates) as in flooring finished even and smooth without using extra cement complete all as specified and as directed.

S&F mild steel work as in wind ties of roof, posts, struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mess etc and necessary) including welding and cutting at bottom etc. and similar work conforming to Fe 290 grade- E165 complete all as specified and as directed.

S&F rolled mild steel conforming to Gde Fe 410-0 in joist, channel, angle or tee sections, fixed independently, without connecting plates etc (cut to ordinary length i.e. within 20mm of length indicated) complete all as specified and as directed.

S&F 35mm thick glazed and skelton shutters of IInd class HW open rebated and prepared to receive glass, gauze, etc. (without sash bars) edge of framming plain chamfered, or rounded, fitted with cut and mitred beads for securing glass etc, size of member of shutters as specified in SSR part I, section 8, clause 8.20(a), supplied and fitted to chowkhats complete all as specified and as directed.

S&F Mild Steel Helical door spring 300 mm, ordinary rat tail rod pattern springs including roller and rollar plate, fixed including welding/ fixing to steel/ wooden chowkats, complete all as specified and as directed.

S&F aluminium anodised window and ventilator shutters, sliding type without sash bars, aluminum sections of size 40mmx20mmx1.5 mm fixed in aluminum anodised frame of section size 63.5mmx38.18mmx2mm including necessary jointing cleats cleats, glazing clips, aluminium anodised snap beading, screws, aluminium beading, pvc packing, aluminium anodised fittings & fixtures with and including galvanised mild steel wire cloth 0.50 mm nominal dia of wire & average width of aperature 1.00 mm and fixed with tinned tacks or galvanised wire staples and necessary fittings & fixtures including powder coating of thickness n.exc 50 micron on all aluminum section, complete all as specified and as directed. (Make-Hindalco/ Jindal)

S&F aluminium anodised window shutter sliding type of size 40x20x1.5 mm in section fixed in aluminum anodised frame of section size 63.5mmx38.18mmx2mm including necessary jointing cleats cleats, glazing clips, aluminium anodised snap beading, screws, aluminium beading, pvc packing, aluminium anodised fittings & fixtures with and including 4.80 mm thick tinted glass with necessary beading / packing and necessary fittings & fixtures, complete all as specified and as directed. (Make-Hindalco/ Jindal)

S&F aluminium chequered grills as on aluminium windows, wight n.exc .0.50 kg / sqm and fixed complete all as specified and as directed

Ditto all as per item No 71 described here-in-before but on vertical surfaces such as skirting fixed on and including 10mm thick rendering in cement mortar 1:4 as backing coat

E/M Works:- Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating invertor AC with EER 3.2.of capacity 1.5 TR. Make- Hitachi, LG, Voltas, Blue Star or equivalent make.

Supply and fix Voltage stabilizer for automatic operation with digital display, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 3.0 KVA. Make- V-Guard (Cat part- VGM 500 DIGITAL), Voltas or equivalent make.

S&F SP&N enclosure with 2 pole and Earth Metal Plug & Socket complete with one single pole C series MCB of 20 Amps rating 20 A SP MCB single phase 240 V complete for AC complete all as directed. Make:- Havells (Cat part- DHDPUSN020/DHDPUDP020), Standard or equvalent approved make.

M&L for concealed point wiring complete with PVC insulated and unsheathed flame retardant low smoke (FRLSH) cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit not less than 19 mm dia, with MS terminal boxes (not less than 1.6 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm multi stranded copper conductor cable of green colour as continuous earth wire with lugs and accesseries complete all as specified and as directed for the followings :-

One light / fan point controlled by one switch

Socket outlet 5 Amps on independent board

Ditto all as per item No 183.00 described here-in-before but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed, flame retardant (FRLSH) cable for 15 Amp socket outlet on independent board including 2.5 sqmm multi stranded copper conductor cable of green colour as continuous earth wire with lugs etc as required

M&L for sub main wiring with PVC insulated, fire retardant (FRLS), unsheathed three single core cable 1100 volts grade with multi stranded copper conductor of size 4.0 sqmm drawn into PVC conduit of any size. From three cable One cable of red/blue/yellow colour phase, second cable black for neutral and third green colour as continuous earth wire including lugs etc connected and tested complete all as specified and as directed.

S&F Modular switch 1 way 6A, 1 module, one way, ISI marked complete all as specified and as directed. Make:- Anchor/Havells or equivalent make.

S&F Modular switch 1 way 16A, 1 module one way, ISI marked complete all as specified and as directed. Make:- Anchor/Havells or equivalent make.

S&F Socket 6A/16A - 2/3 pin combined 2 module type, ISI marked complete all as specified and as directed. Make:- Anchor/Havells or equivalent make.

S&F Modular Ceiling Rose three terminals complete all as specified and as directed. MAKE- LEGRAND, PLAZA, Anchor

Supply & laying in trenches/drawn through pipe/through wall/floor XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sq. mm 4 core complete all as specified and as directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for under ground cable and getting out in soft/disintegrated rock complete all as specified and as directed.

Removing excavated material (soft/disintegrated rock) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick in soft/disintegrated rock complete all as specified and as directed.

Supply and laying Bricks; common burnt clay building bricks, sub-class ‘B’ designation 75 Old size bricks for the protection for underground cable complete all as specified and as directed.

Supply and laying in treches for fixed Wall/floor or passing through ducts GI tubing light grade of sizes 40mm bore for protection of UG cable with necessary complete all as specified and as directed.

Supply and spread clean rever sand in trenches above and below underground cable complete all as specified and as directed. Note:- Only punned down thickness shall be measured and paid)

S&F 2'x2' T5 grid ceiling fitting with Ultra modern designed architectural 2'x2' 28W LED luminaire which Provides soft light and glare free symmetrical illumination suitable for Armstrong /Grid ceiling, integtated elecronic driver etc, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. Cat Part No LHEWEIP7PW1W028 Make:- Havells or equivalent in PHILIPS, Crompton Greaves.

S&F MCB single pole 6 to 32 Amps 240 V, 10KA, 'B' series, complete all as specified and as directed. Make- Havells, Legrand, Schneider

Supply and fix triple pole MCB 32A, 10KA complete all as specified and as directed. Make- Schneider (Cat part-SE-A9F74332), Havells, Legrand

S&F triple pole and neutral 4 way sheet metal encolsure double door for 415V fixed to wall in the dummy space complete all as specified and as directed. Make- Havells/ Legrands

M&L for earthing complete with galvanised steel earth plate electrode 600×600×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point complete all as specified and as directed including testing on completion. Note- Quoted price included of PCC pit chamber, RCC pit cover, Funnel with wire mesh and 20mm GI pipe (Not less than 7m) for protection of lead wire.

Supply, install testing and commisioning of maintenance free chemical earthing system conforming to IS: 3043. New chemical earthing using 77mm dia 3000mm long copper rod with chemical material. The quantity of ground enhancing compound Marconite shall not be less than 45 Kg per pit. The electrode shall be provided on its top with an earth termination clamp made out of electrolytic grade copper for connecting earth continuity conductor with stainless steel hard ware. PCC chamber of size 300x300x300 mm with cover shall be provided on the top of the earth system on 100 mm thick PCC 1:3:6 bed concrete. The chamber shall burried in ground with top edge projecting upto 75 mm from ground surface. Note:- i) THe quoted rate shall deemed to be include cost of copper strip 32mm x 6 mm upto 7.5 m length. ii) The earth resistance shall not be more than ONE Ohm. The contractor shall give a written guarantee for maintaining earth resistance of less than ONE Ohm for a period of 5 years from the certified date of completion and to arrange security deposit of Rs 5000 each per earthing for five years. The fault current should not be less then 35KA, in this regard CPRI/ERDA/NABL Approved LAB Test REPORT is Mendatory. MAKE- ELANCRETE/ VASCONITE/ Marconite.

M&L for street light bracket made out of 40 mm dia light grade GI pipe bend to shape not less than 1.8 mtr length along with 02 Nos fixing clamps properly shaped and fabricated out of 50 x 5 mm thick MS flat nut & bolts duly painted with 2 coats of aluminium paint over 1 coat of red oxide complete all as specified and as directed.

S&F LED street light made up of pressure die cast housing with toughned glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07 on existing bracket on domestic building of wattage 25 W applicable for area lighting complete all as specified and as directed. Cat Part No-LHETAXU7PA6S025 of make Havells, or equivalent model in philips, Crompton

Supply, Laying, testing & connecting of Cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty standard aluminum conductor 1100 volts 35 sqmm 3.5 core complete all as specified and as directed.

S&F in replacement high efficient high power 60 Watt LED flood light with lens with pressure die cast aluminium housing, reflector and enclosed with toughened glass with IP 66 protection complete all as specified and as directed. MAKE- Halonix cat No-HLFLD-ML21-60-CWL or equivalent in/ Havells/ Philips

S&F MCB DB 4 Way TPN with 200 Amps rated bus bar double door complete all as specified and as directed. Make-Legrand/ L&T/ Siemens

S&F MCB DB 8 Way SPN with 200 Amps rated bus bar double door complete all as specified and as directed. CAT part No Legrand 6077 11 or equivalent in L&T/Siemens

S&F MCB TPN 63A, 415 Volts, 'B' series including connection with suitable size aluminium/copper lugs complete all as specified and as directed. Make: Legrand/L&T/Siemens

S&F MCB SPN 6-32 Amps 230 Volts 10KA, 'B' series including connection with suitable size aluminium/copper lugs complete all as specified and as directed. Make Legrand/L&T/Siemens

S&F switch piano in replacement flush button type 5 Amp single pole one way ISI marked complete all as specified and as directed. Make:- Anchor/ Cona/ SSK

S&F switch piano flush button type 15 Amp single pole one way ISI marked complete all as specified and as directed. Make:- Anchor/ Cona/ SSK

S&F socket outlet 2in1, 3 pin, 5 Amp and 15 Amp flush type ISI marked complete all as specified and as directed. Make:- Anchor/ Cona/ SSK

S&F socket outlet 2in1, 3 pin, 5 Amp flush type ISI marked complete all as specified and as directed. Make:- Anchor/ Cona/ SSK

M&L for sub main wiring with four single core PVC insulated stranded unsheathed FR PVC insulated cable copper conductor three run single core with size 6 Sqmm and drawing through non metallic PVC rigid conduit conealed in wall including one run 4 Sqmm PVC insulated unsheathed stranded copper conductor cable connected to earth and earth dolly in conduit including connecting to main board complete all as specified and as directed.

S&F in replacement of single core FRLS cable PVC unsheathed with copper conductor of size 1.5 Sqmm and drawing into existing conduit complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket, bell or power) complete including all electrical fittings & fixtures (DBs, submain, cables etc) and making good disturbed surfaces of wall, floor etc and matching wth original colour of wall, complete all as specified & as directed

Supply & fix exhaust fans heavy duty 300mm dia 900 RPM for domestic use, dynamically balance blade, epoxy powder coated with ISI marked IP-55 with class B insulation motor including louvers shutter complete all as specified and as directed Make -Khaitan /Almond /Havells

S&F enviroment friendly indoor decorative 18 Watt LED plastic Batten with opal diffuser including all accessaries complete all as specified and as directed. Make:- Halonix cat No HLB-33-18-CW-IP or equivalent in Philips/ Havells.

S&F enviroment friendly indoor decorative 10 Watt LED plastic Mirror light with opal diffuser including all accessaries complete all as specified and as directed. Make:- Halonix cat No HLB-33-18-CW-IP or equivalent in Philips/ Havells.

Supply & fix metallic body storage type geyser of capacity 25 Ltrs 2000 watt 230 V, 1 Phase, 50 Hz AC with minimum 4 star BEE rating and tank made of ultra thick super cold rolled steel plates and viterous enamel coated with heavy duty magnesium anode including all accessories comlete all as specified and as directed. Make- Havells cat No GHWENZTWG025 or equivalent in Bajaj/ Crompton

M/S Rohit Enterprises

akhil enterprises

Ish Engineers and Contractors