Gate with Gearing system

Amount

Excavation in Soil (any type) using Hydraulic Excavator CK 90 with hydraulic excavator of 0.9 cum bucket capacity including cutting, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, including all lifts and combined lead upto 30m.

Dismantling pucca grouted pitching

Dismantling stone spalls or Brick bats filling In wire crates including opening of crates and stacking crate material

Dismantling of brick work in cement sand mortar / lime mortar including T&P scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material. & staking the serviceable material with all lifts & lead of 100 metre (By Mechanical Means)

Dismantling Cement concrete plain 1:4:8 or 1:5:10

Dismantling Reinforced cement concrete

Weaving wire netting for wire crates including binding sides and partitions to make crate of 15 cm x 15 cm or 25 cm x 7.5 cm mesh including supply of MSA wire 4mm as per Pwd Specifications.

Providing & Filling stones or spalls into crates and hand packing Including supply of Boulder stone and carriage from approved quary , loading & unloading, stacking within 15 meters & rehandling of b/s from stackyard to site within lead of 1 km i/c loading & unloading etc. complete in all respect.

Grouting stone filling or pitching:- Cement Mortar

First class burnt brick work laid in cement sand mortar 1:4 in foundation and plinth

Cement Concrete 1:4:8 with Stone Ballast or shingle mixing by mchanical means using concrete mixer volumetric type

Cement Concrete 1:2:4 (M-15) with Stone Ballast or shingle mixing by mchanical means using concrete mixer volumetric type

RCC M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth.

RCC M-25 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth.

Cold twisted detormed (Ribbed/ ToR Steel Bar) Bars (Fe 500 grade ISI 1786- 2008), for R.C.C works, where not including in the complete rate of RCC including bending and binding placing in position complete

Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia PVC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications

Earth work compaction Extra for laying earth/fly ash as per specifications in 20 cm. Layers and dressing but excluding cost of rolling.Extra for watering the earth/fly ash laid in 20 cm layers as per specifications for compaction.Extra for rolling to specifications.

Laying 1.50 thick boulder stone pitching i.e 1.00 thick boulder stone over 0.50 thick spall

Dry brick on edge paving on ramp

Filling brick ballast under brick floor

s/o GI -Pipe 50 mm dia

Disposal of surplus E/W within lead 1km

Providing and fixing of ISMC

Providing and Fixing of MS Skin PLATE for Gate complete in all respects

Providing and Fixing of MS PLATE for Gate Frame complete in all respects

Providing and Fixing of ISPL for Gate Frame complete in all respects

Providing and Fixing of ISPL S. STEEL for Gate Frame complete in all respects

Providing and fixing Of ISMB

Providing and fixing Of ISA

Providing and fixing Of GI Pipe

Providing and fixing CHEQUERED PLATE 8 MM

Supply Of J-ANCHOR/bolt Dia 16 mm

Supply Of J-ANCHOR/bolt Dia 20 mm (16) @ 1.11 kg/pc

Gate wheel Assembly 160 Dia 50 wide complete in all respect to entire satisfaction of engineer-in-charge (1 Gate x 4 Nos.)

Providing and fixing of Galvanized nut and bolts of all size and length required

Drilling /boring hole including complete in all respects and to entire satisfaction of engineer-in-charge

Fillet welding with high strength steel rods, complete in all respects and to entire satisfaction of engineer-in-charge 6mm wide

Providing of hollow bulb seal and fixing in postion including preparation of surface complete in all respects and to entire satisfaction of engineer-in-charge 120/44 item no.B 14 & 20

Providing and fixing in postion of flat/wedge seal including preparation of surface complete in all respects and to entire satisfaction of engineer-in-charge 80 mm Ø x 12 mm Th. item no.08

Supply of multipurpose synthetic Hetiv grease (2 x 10)

Supply of multi grade mobile oil. (2x10)

Scraping brushing to remove paint to base metal surface.

Painting two or more coat of Anti corrosive odourless black bitumastic paint

Applying priming coat with metal primer on new steel or iron work including preparation of surface.

Painting two or more coats excluding priming coat with ready mixed paint for metallic surfaces in all shades on steel or iron work

Provinding Installation of stop lock gate with the help of Hydraulic CRANE 35 TON CAPACITY

Commissioning and testing of gates at site complete in all respects and to entire satisfaction of engineer-in-charge.

Overhauling of gate mechanism of all types including dismantling,greasing, oiling and re-installation of mechanism complete in all aspects.

Miscellaneous minor repairs of Items Such as M.S Flats, ISA, ISMC, ISMB etc. to make gates operational including labour charges.

CI housing cover with worm and worm wheel Assembly ,shaft,handle G.M Bust with triple start threading i/s for spindle complete i/c labour charges

MS Spindle with double start ot triple start thriding 11' height 1/3/4" Dia Complete above 2.5 ton capacity

THE KAKEPUR COOPERATIVE L AND C SOCIETY LTD