SPL REP TO BLDG NO ET 65 AND SPL REP REPLACEMENT OF OLD VINTAGE TABLE LAMP AND CONNECTED ITEMS OF P 78 AND P 79 OF SAW BLDG AT ASC CENTRE AND COLLEGE UNDER GE (CENTRAL) BANGALORE

Taking down cement plaster of any description including racking out joints, hacking for key scrubbing down with water etc and removal of debris outside MoD land and depositing where directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exceeding 15 cm thick above or below ground level and removal of entire debris as ordered outside MD land complete all as directed.

Demolition of cement concrete (Reinforced) in manhole cover not exceeding 15 cm thickness (below or above ground floor) (reinforcement cut as required to facilitate demolition) including removing of debris as ordered outside MD land complete all as directed.

Demolition of brickwork , block masonry or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc and removal of debris as ordered outside MD land complete all as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from frame) and stacking at site where directed.

All as per item 5 here-in-above but exceeding 1.5 Sqm but not exceeding 4 Sqm each

Dismantling wall and ceiling board fibre pulp, insulation etc or insulation boards any thickness including cover fillets complete all as directed.

Dismantling of AC Corrugated or semi corrugated sheet etc any thickness including ridges as in roof covering and stacking at site where directed and removal of debris to a outside MOD land and depositing where directed complete all as directed.

Dismantling boarding, any description, fixed in any position with nails and stacking at site where directed for Credit.

Dismantling of timber scantlings 40 Sq cm and over in section in any position unframed work and stacking at site where directed complete.

Dismantling of wooden battens for tiles of any size including tiling fillets exe 15 cm spacing complete and stacking where directed.

Dismantling floor, hearth or wall tiling inluding cement mortar bedding (but not backing), stacking serviceable tiles at site and removal of entire debris as ordered outside MD land complete all as directed.

Excavation in trenches and not exe. 1.5 m wide and not exe. 1.5 m in depth for foundation of drain, man hole , laying of UG cables etc. not exe. 10 Sq. m on plan and not exe. 1.5 m depth and getting out in hard /dense soil complete all as specified and directed.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft rock complete all as specified and directed

Removing excavated surplus soil to a distance not exceeding 50 mts and depositing where directed .at a level not exceeding 1.5 M above the starting point complete all as directed.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed

M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately

M&L factory made pre cast PCC 1:3:6, type C1 (using 20 mm graded granite aggregate) as in block masonry with solid blocks, exceeding 10 cm in width and setting in CM 1:6 complete all as specified.

All same as per item No 18 here-in-above nut not exceeding 10 cm thick -do-

Supply only Integral Water Proofing Compound (ISI Marked) of Make : CICO, Acco Proof, Impermo, Aqua flex as approved.

M&L Second class hard wood well seasoned wooden scantling clean sawn framed & fixed to walls or timber frame fixed with screws complete all as directed.

S&F 20mm thick second class hardwood boarding, clean swan fixed with nails in any situation (except flooring and skirting), Planed one side with butt joints, complete all as specified

All same as per item No.22 here -in - above but except wooden boarding - (Note : wooden boarding obtained from item No 9 here -in - above)

M&L for Second class hard wooden battens spaced at 30 cm centre to centre clean sawn cross sectional area exceeding 5 sqcm but not exc 15 sqcm complete all as directed.

S&F solid PVC door frame of size 50X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification all as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed..

M&L for Prelaminated particle board 9mm thick, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as directed.

S&F 75 mm size butt hinges, medium weight cold rolled mild steel and fixed .

S & F 100 mm long aluminium, anodised , barrel tower bolt (ISI marked) of extruded section and fixed.

S&F 100 mm size aluminium alloy handles (ISI Marked) fabricated type anodised and fixed.

S&F 300 mm long aluminium alloy, anodised sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F in repair 25mm dia aluminium anodised decorative type curtain rods.

S&F brass chromium plated type curtain brackets suitable for 25 mm dia curtain rod along with wooden support complete all as directed.

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed

S&F anodised aluminium powder coated (minimum thickness of powder coating 50 micron) frames, sliding guide channels for shutter for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc. complete all as directed.

S & F powder coated aluminium sliding window(three way) frame & shutter with glazed shutter and without wiremesh shutter/skelton section with the following details :- (i) Aluminium frame section 116x36.50x1.80mm (ii) Aluminium shutter glazed/skelton section 50x20x1.50mm thick. (iii) Aluminium grill size 50mmx50mm and 4 to 5mm thick bars as complete all as specified. (iv) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in roiginally shape. (v) 4mm thick glass ordinary quality and fixed with rubber gasket for with glazed shutter etc. (vi) Stainless steel wire mesh 0.36mm nominal dia avg apearature 1.14mm and fixed with rubber gasket for without glazed shutter etc. (vii) Aluminium disc/ work handle and locking system complete.

S & F mild steel powder coated body stopper with hard drawn steel spring , 150 mm size fixed to door complete all as specified

M&L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in floor complete all as directed.

S & F in repairs brass chromium plated tubular towel rail, 20mm dia ‘D’ type, 600mm long between flanges complete all as specified and directed.

S&F 10 mm dia and over TMT bars cut to length bent to shape required cranking including bending , hooking ends etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

S&F pre-painted galvalume (zincalume) aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to walls fixed with self tapping screws as specified.

Supply and fix Pre- painted galvalume aluminum zinc coating GI plain sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction all as specified and as directed.

S & F for 4 mm thick of size 600x600mm Non Asbestos fibre cement building boards fixed for laid / inserted to timber / GI Aluminium frame work ( White colour) to be fixed and including Aluminium snap grid/ section size 600x600 mm duly suspended 6 mm dia GI hangers (1200mm length) adjusting level fixed to roof slab or purlins by means of ceiling cleats made out GI flat 40x3mm size 60mm long and expension holdfasteners 12.5mm dia 40mm long complete all as specified.

M & L for 75 mm thick plain cement concrete 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in sub base of path and finished the surface complete all as directed.

M & L for 75 mm thick plain cement conctere 1: 3 : 6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection finished the surface fair and even complete all as directed.

M&L for 25 mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in padding / levelling course / subbase of floor etc floor and finished the surface even & rought complete all as directed.

M & L non-skid coloured joint free ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all directed and specified.

M&L glazed ceramic designer tiles any shade or pattern as approved of size 350x250x7mm / 450x350x7 mm thick, on verticals surfaces, set and jointed in neat cement slurry including 10 mm thick back coat in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all directed. (Note for item Nos 62 to 65 : i) Quoted rate is deemed to be inclusive of cement screed. ii) Shade / pattern / Colour of tiles shall be got appproved before procurement).

M&L for 18-20mm thick Sadherhali stone slab flooring, steps, jambs, pillars, window- cills, cooking platforms and like in 20 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granit laid complete all as directed including Rounding to edges complete.

All same as per item No 49 here - in - above but as in dado & skirting with 10 mm thick 1 : 3 cement mortar screed - do -(Note for item No 49 & 50 : i) Quoted rate is deemed to be inclusive of cement screed.)

M & L Chequered cement concrete tiles (glosssy) of size 40cm x 40cm x 20 to 25mm thick (with grey cement and pigments) set, jointed and pointed in neat cement slurry in floor,laid over and incl 20 mm thick cement screed base in CM 1:6,laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl cutting, rubbing, grinding complete all as specified.

M & L for Rendering 15 mm thick in cement mortar 1:4 on internal concrete surface mixed with WPC @ the weight of minimum 2% by weight of cement mixed or as per manufacturer instruction , and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC measured and paid separately.

M&L for rendering 15 mm thick in CM 1:6 on brick or concrete surfaces or surface other than fair faces brick work, finished even and smooth without using extra cement complete all as specified.

M&L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as ordered complete all as specified.

Complete removal of any type of exixting treatment from walls surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3 mm thick white cement based wall care putty as specified complete all as specified.

M&L prepration of newly plastered surface of walls applying 3 mm thick white cement based wall care putty , applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint (Apex -Ultima Protek) of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces applied by mechanical means i.e Airless spray including filing undulations with white cement based putty mixed with multi purpose mixer complete all as directed.

Supply only 5.50mm thick sheet glass ordinary quality in square/rectangular in each panes.

M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth not otherwise described and treated with two coats of creosote oil complete all as specified

Taking up or down 25mm bore, steel tubing galvanised along with fittings or any other type of pipe and removing complete (work related upto 5th floor height).

Taking up or down 20mm bore, steel tubing galvanised along with fittings or any other type of pipe and removing complete (work related upto 5th floor height).

S&F 25 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.

S&F 20 mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed on walls/ceiling or laying in floors making necessary connection& testing on completion complete all as directed.

S&F in repair 15mm dia cast copper alloy Bib taps fancy type , with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as directed.

S&F in repair 15 mm bore stop valves/angle valve cast copper alloy chromium plated fancy type with long shank and cup, screwed down to iron pipe complete all as specified and directed

S & F in repair 2 way bib cock double handle with flange, cast copper alloy chromium plated, screwed down, suitable for 15mm bore iron pipe. Make: PRAYAG Cat No P6812 or equvelent of Make Hindware/Parryware/CERA

S&Fin repair health faucet ABS body with wall hook and 1 metre long SS braided rubber hose pipe and wall hook mounted type complete. Make: Prayag Cat No BEA-40 or equivalent in approved make.

S&F 20 mm size Gun metal globe or gate valves (ISI Marked) conforming to IS 778 : 1984 with iron wheel head screwed box and both ends for iron pipe or union complete all as directed

S&F in repairs CP Soap dish 150mm, fixed to wall with chromium plated brass screws complete all as specified

S&F in repair Vitreous China Wash hand basin , white flat back size 550x400 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall, pillar taps, brass, with capston heads, fancy type, chromium plated, 32 mm waste coupling brass chromium plated suitable for wash hand basins & 32 mm dia LDPE PVC waste pipe, PVC connection 15 mm size 450 mm long including cutting hole and pinning in ends making good disturbed portion using cement mortar 1:3 complete all as specified & directed .

S & F in repairs, vitreous China wash down water closet pan (pedestal pattern), white, including connection to outgoing drain and 32mm dia flush pipe,flushing pipe, anti syphonic pipe with and including white PVC seat and cover closed pattern with flat bottom and MS chromium plated hinging device including provision of 10 ltr capacity low level PVC Flushing cistern, PVC connection pipe, 15 mm dia, 600 mm long complete including making good damaged/disturbed surfaces complete all as specified and directed. Make of Pan CERA Cat No S1053101/S1053102 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S&F sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 495mm x 420 mm with bowl size 410mm x 330mm x 160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink (Make: Prayag Cat No 1322D or equivelent of Parryware /Hindware/Cera)

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to wall in repars complete all as directed.

All same as per item No 113 here-in-above but laid on floors -do-

S & F 110 mm bore, PVC (SWR) bends of any radius with access door complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius with access doorcomplete all as specified and directed.

S&F inrepair 75 mm size PVC (SWR) floor trap with grating including jonting the same with solvent cement complete all as directed.

Dismantling of existing any type & any capacity water storage tank fixed in any description and stacking at site and S&F new 1000 litres capacity (white colour) rotational moulded polythene water storage tank, (cylindrical vertical with close top) triple layer colour white both inside and outside with top cover including PVC float valve high pressure suitable for 25 mm bore of pipe with polythene float, fixture hoisted and fixed in position where ordered and making necessary connection and testing complete all as directed.

E&M : Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc. to be measured separately), removing taken down materials to a place where ordered for crediting including making good disturbed surfaces of walls, floors, etc to match with the existing surface complete all as directed..

Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic conduit (Medium Grade) concealed in wall conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :-(a) One light / Fan / bell point controlled by one 5 Amps switch one way

(b) One 3 pin socket point 5/6 Amp on independent board

(c) One 3 pin socket point 5/6 Amp on same board with other switches.(to be provide new point as user requirement)

All as per item No. 80 here-in-above but with 2.5sqmm ( Nominal area ) cable with 2.5 Sqmm size copper earth continuity conductor for 3 pin 15/16 A socket outlet on independent board complete all as specified and directed.

Supply and fix Switch piano, flush button single pole, 5 Amps one way.

Supply and fix Switch sokcet combination flush type 5 Amp 2/3 pin muliti purpose

Supply and fix Switch socket combination flush type 6/16 Amps 3/3 pin universal multipurpose

S&F ceiling rose surface bakelite White / Ivory / Urea finish 50 mm dia three terminals including supply and fix PVC square mounting block complete all as specified and directed.

Supply and fix fan regulator electronic , step & socket type 230 volts , suitable for 1200 /1400 mm sweep ceiling fan complete all as directed.

S&F Bell push,flush type,240 Volts AC complete all as directed.

S&F electric Bell, AC, 230 volts, single pole complete all as specified and directed.

S&F in replacement LED tube light fitting of 20 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with wall mounting all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm with all as specified and directed .

Supply and fix LED tube light fitting, 1x10 watts,6000k 230 volt, with extruded aluminium housing provided efficiant heat disspation with poly corbonate diffuser, all pre-wired fixed on walls with all fixing accessories such as 2 nos of PVC square/round blocks, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed.

Supply and fix LED bulb fitting of 7 Watts bulb of red and green indication lamp with holders, 230 volt, , all pre-wired fixed on walls with all fixing accessories such as 2 nos of PVC square/round blocks, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed.

Supply and fix 35/36 watt LED Light 2' x 2' LED luminare recessed mounted with polymer diffuser complete with accessories suitable for armstrong/Grid ceiling with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S&F in replacement LED stuty lamp of 9/10 watts, 230 volt, with Basic all purpose surface and wall mounted LED batten with metal housing & integrated electronic driver complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed.

S&F bldg security light fittings 1x 35 Watt Ac 230v out door type LED street light with high pressure die cast aluminium and heat ressistent complete with driver ,lamp bracket with impact and corrosion resistent including thermal managment in multiple optics complete , IP65/66 and wired with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed.

S&F street light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F submain wiring with 2 runs of 4 Sqmm single core PVC insulated, unsheathed, multi stranded copper conductor and one single core 4 Sqmm PVC insulated , unsheathed , multi stranded copper cable as earthing lead as per IS : 694 / 1990 drawn through and including non-metallic PVC rigid conduit/casing caping of size as ordered in walls / ceilings etc with all accessories such as Tees, Elbows, junction box, reducers etc and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note :- 2 runs 4 Sqmm cable , one run 4 Sqmm cable and one run of PVC Conduit /Casing caping shall be measured as one unit length) .

All as per item No 98 here-in-above but 2 runs with 6 Sqmm single core cable and 6 Sqmm single core as earth contunity wire -do- . (Note :- 2 runs 6 Sqmm cable , one run 6 Sqmm cable and one run of PVC Conduit/Casing caping shall be measured as one unit length)

Supply and fixing post top lantern LED type 20 watt ,warm white 230 volt AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion complete with driver and lamp including pole box complete all as specified and directed by Engr-in-charge.

M&L for PVC insulated 2 x1.5sqmm + 1x 1.5 sqmm earth wire single core copper conductor for connection of post top lantern to Pole Box with PVC conduit complete all as specified and directed.Make: Plaza/Polycab/Finolex

Supply & fix in repair FRP junction box (weather proof) of size 150 x 150 x 70 mm including single phase connector arrangement alongwith suitable clamps including MCB SP 5 Amps 10 KA rating,fixing with flat iron clamps, nuts and bolts complete all as specified and directed.

Supply and fix in repair Rigid Non-metallic PVC conduit pipe exclusive of junction boxes but inclusive of all Tees,bends elbows,reducers, bell mouth tube end and fixing acessories such as couplers, lock nuts,saddles pipe hooks etc and fixing to poles etc of size 20 mm external dia. etc all as specified.

S&F Sheet metal enclosure (ISI marked) distribution board for 415 volts, TPN 4 way Vertical type, double door, triiple pole and neutral with incoming MCCB 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.(Note : MCCB measured & paid seperately ).

S&F Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 8 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix in repair MCB Tripple pole & neutral 40 to 100 Amps 415 volts, C series,10 kA rupturing capacity providing in DB complete all as specified.

S & F MCB single pole 6 to 32 Amps 240 volts, 'C' Series 10 kA rupturing capacity providing in DB complete all as specified and directed by Engr-in-charge.

S & F MCB single pole & neutral 40 Amps 240 volts, 'C' Series10 kA rupturing capacity providing in DB complete all as specified.

M&L for taking down and dismantling of ceiling fan 1200mm/1400mm sweep 230 Volt 50 C/S AC of any make or model by opening the cover, separating down rod, rotor and stator assembly, locating the fault and making the fan fully in serviceable condition with & including replacing the bearing with similar type of exisitng one, worn out screws of the cover, split pin, twin core flexible copper wire of size 23/0.0076, locking nuts & machine screws with spring washer for ceiling fan blades, oiling and greasing including rewinding of ceiling fan by removing of burnt winding from stator and rewinding the same with super enamelled copper winding wire of same gauge, same weight & turns including varnishing of winding etc & finally painting the ceiling fan with one coat of spray painting with white DUCO Paint & lettering & Numbering the same as per existing ,reassembling , refixing the same in same or different location asordered & finally testing the fan , complete all as directed. Note : (i) Spare Parts/accessories found unserviceable including bearings , rewinding etc which are required to make the fan functional shall be providsed by the contractor without any extra cost to Govt as quoted rate is deemed to be inclusive for the same .(ii) Quoted rate is deemed to be inclusive of painting .

S & F exhaust fan, single phase, 150 mm (6") sweep, plastic body 1200 RPM including fixing of mounting frame in the round/square hole cutting in the wall/ventilator etc, by means of rugged bolts, nuts and washers etc,including connecting with three core copper conductor flexible cord of 0.5 Sqmm cross sectional area of required length from ceiling rose to the porcelain connector block of the exhaust fan, complete all as specified and directed by Engr-in-charge.

M&L, Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 4 mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia light grade pipe, funnel, wire mesh, common salt chorcoal, necessary excavation and earth work in any type of soil complete all as specified.

M&L for Sand cushioning/sand covering for underground cable protection complete all as specified. Note: Punned thickness only will be measured and paid.

Supply and laying sub class 'B' bricks of old size (standard size as per local availability) laid along alignment of cable as protection to cable in trenches complete all as specified and directed by Engineer-in-Charge

S&Fmild steel galvanized pipe light grade for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps as required at site all as specified for size of 50mm bore dia.

Supply, fixing ,Teting and commissioning XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty) with stranded aluminum conductor, 1100Volt grade on walls with fixing acessories of 35 Sqmm 3.5 Core all as specified and directed.

Supply, fabrication, installation and testing of LT out door type factory made(CPRI Approved ), junction box of size 900mm(H)X700mm(B)X400mm(W) (over all dimension ) made out of 3.15mm thick CRCA sheet dully supported with mild steel angle iron of size 40X40X5 mm frame, 04 Nos aluminium bus bar of of capacity 250 Amps with drilled hole for incoming/outgoing cable connection with necessary alumiium lungs, GI nuts bolts and washer including 08 Nos bridge insulator DMC , heavy duty, suitable for 3 Phase 4 wire system, one danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled white with letters, figures and conventional skull & bones in signal red colour and fixed in front door size and PCC (1:3:6) type C-2 foundation 0.30m above normal ground level & 0.30m below ground level with necessary exacavation and earth work and painting to internal and external steel surface with powder coated (Siemence gray) RL-35 after neccesary preparation of surfaces including Indicating lamp LED type 240V 50 Hz AC -one set of 3 Make: L&T/Havells/HPL compete all as directed.include (a) One Incoming MCCB 4Pole 100 Amps, reperuig capacity 25 KA