Spl rep to bldg No P 8 provn bathroom toilet block and certain sanctioned work under AGE BR II of GE N Mamun

Amount

Excavation in trenches n. exc 1.50 m wide and n.exc 1.50m in depth for foundation and getting out in any type of soil, complete all as specified and directed.

Excavation over areas, n.exc 1.5m deep and getting out in any type of soil complete all as specified and directed.

All as per item 2 but depth exc 1.5m but n.exc 3.0 m

Surface excavation n exc 30cm deep avg 15 cm deep and getting out in any type of soil, complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L Brick work with Fly Ash bricks old size, straight or curved on plan exc 6 mtr mean radius built in CM (1:6) complete all as specified and directed.

M&L Brickwork with fly ash bricks, old size straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed.

All as per item 7 but as in Slabs supported on walls, beams and columns in floors roofs, landings, balconies, canopies, deck slabs and in shelves and the like.

Use and waste of form work to sides and soffits of floor and roof beams, beams haunching, girders, bressummers, lintels and cantilever, shelves including supports over hangs etc rough finished surfaces of concrete ( flat ) complete all as specified and directed.

All as per item 9 but of suspended slabs not exceeding 200mm thick (horizontal or sloping).

All as per item 9 but to edges of concrete flats, treads, , breaks in floors, window cills, concrete railings, openings in concrete walls, floors & roofs n exc 20cm wide & sides of RCC/PCC bands in walls, horizontal or sloping, & similar work exc 10cm but exc 20cm wide

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removal of surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding above the starting point complete all as specified and directed.

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed.

All as per Item No 14 but 6mm to 8mm dia bars

All as per Item No 14 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L PCC 1:2:4 type B-0 in roof kerbs or mud stops, rounded or chamfered on edges, benching on chajjas , surface finished even and smooth without using extra cement complete all as specified and directed.

Spreading & leveling of excavated earth in layers n.exc. 25cm thick, well ramming including watering and consolidation complete all as specified and directed.

M&L Hardcore of guage exc 63mm, broken Stones or boulders deposited, spread and leveled in layers n exc. 15 cm thick, watered & rammed to a true surface complete all as specified and directed.

M&L PCC 1:3:6 type C-1 using 20mm graded aggregate as in plinth protection and paving 75mm thick laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified and directed.

M&L for 100 mm thk PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floors complete all as specified and directed.

M&L 25 mm thick PCC , type B-1 using 20 mm graded stone aggregate in flooring complete all as specified and directed.

M&L screed bed or bedding layers of mortars 15 mm thick in CM 1:4 for laying floor finishes complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement complete all as specified and directed.

M&L glazed ceramic coloured tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10mm thick in CM (1:4) and finished rough, complete all as specified and directed.

M&L Rendering 10mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and directed

M&L for Rendering 5 mm thick cement plaster on faces of brick work or concrete surfaces in cement mortar 1:3 as in ceiling finished even and fair without using extra cement all as specified and directed.

M&L three coats of white wash on surface of wall including preparation of new plastered surface cement all as specified and directed.

M&L Preparation of new plastered surface of external wall and chajjas, making surface smooth using sand paper, priming surface with alkali resistance primer, applying two coats of cement base paint including curing complete all as specified & directed.

M&L three coats of white wash on ceiling surface including preparation of new plastered surface complete all as spd and directed.

M&L for Box type steel windows comprising of tubular frame and shutters made out of 1.25 mm thick MS sheet tube factory made with double side shutters wire gauged shutter & glazed shutter (wire cloth and glass panes shall be measured and paid seperately), side hung shutters with steel handle and steel peg stay dovetailed or welded with 2 Nos tower bolts 150 mm long for each leaf, 10 mm square bar grills at spacing as shown on drg, welded to FI frame work, including other fittings viz hinges, handles, tarred hold fasts, PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F factory made pressed steel door frames made out of MS sheet 1.25mm thick of size 105x60 mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, back of chowkhats filled with PCC 1:3:6 type C-0 (12.50 mm graded stone aggregate) and painted with two coats of synthentic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated fitted to chowkats complete all as specified and directed

M&L preparation of wood or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frames shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom railon either side and as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification & drawing.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks, or galvanized wire staples complete all as specified & directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead / glazing pins in squares size n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F 100 mm long Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts complete all as specified and directed.

S&F for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed complete all as specified and directed.

S&F 150 mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified and directed.

S&F Peg set of Six powder coated fixed with chromium plated brass screws and wooden and plastic cleats ( min wt 190 gms) complete all as specified and directed.

S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc complete all as specified and directed.

M&L cutting chases pinning in brick work and making good to facing where required, making good in CM 1:3, cutting n.exc. 10 cm in girth complete all as specified and directed.

S&F 20mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc complete all as specified and directed.

S&F 20 mm bore dia gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed cast copper chromium plated, fancy type alloy ISI marked with crutch or butter fly handles screwed down screwed for iron pipe complete all as specified and directed.

S&F Angular Stop valve cast copper alloy (ISI Marked) fancy type, chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe 15mm bore dia, complete all as specified and directed.

S&F Stop valve concealed cast copper alloy (ISI Markd) fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia, complete all as specified and directed.

S& F CP Shower rose with or without swivel joints, any size, including fixing to steel pipe or union complete all as spd and directed.

S&F Bib taps for 15 mm bore dia pipe, cast copper alloy fancy type chromium plated complete all as specified and directed.

S&F Vitreous china wash basin (Oval Shape), white flat back, size 550 x 400 mm including waste pipe , brackets and cutting for and pinning in ends of brackets or errecting stand and 32 mm dia PVC waste pipe including waste copling 32mm size full thread complete all as specified and directed.

S&F 15mm bore dia pillar cock fancy type, screwed down high pressure with or without letters hot or cold with long screwed shank and fly nuts screwed for iron pipe ISI marked complete all as specified & directed.

S&F Liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 105 gms) complete all as specified and directed.

S&F towel rail Brass CP 600 mm long complete all as specified and directed.

S&F Vitreous China squatting pan of orissa pattern, size 580x440mm white with S&F of CI ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern ( including fixing of flush pipe) including provision of cement concrete bedding, in repair complete all as specified and as directed.

S&F Vitreous china wash down water closet pan (pedestal pattern), white, trap, Plastic water closet seat, black, closed pattern with flat bottom & cover inluding mild steel chromium plated or aluminized hinging devices complete all as specified and as directed.

S&F Jet Spray (with 1.50 mtr tube) fixed to EWC and Angular Stop Cock complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

M&L for Rotational moulded polyethlene water storage tanks of capacity 1000 litres, three layers (cylindrical vertical with closed top with screwed type cover) hoisted and fixed in position all as specified in SSR Part I, 20mm dia ball brass valve high pressure with polythene floatand flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified & directed.

S&F 100 mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears laid in floor/wall with lead joints complete all as specified & directed.

S&F 100mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured) with ovel asses door complete all as specified and directed

S&F Cast Iron Branch peices, Double (equal or unequal) ordinary or inverted (spigot or socket type), or with parrallel branches, fitted with oval access doors of 100 mm bore dia complete, ISI Marked, fixed in repairs complete all as specified and directed

S&F 75 mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears laid in floor with lead joints complete all as specified and directed

S&F 75mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears fixed to walls with clamps and cement jointscomplete all as specified and directed

S&F 75 mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified and directed

S&F 75mm dia CI bends (any radius) diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and directed

S&F CI floor trap 75 mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with CP grating with ot without hole for waste pipe complete all as specified and directed

S&F cast iron cowl for 75 mm dia complete all as specified and directed

S&F cast iron Swan necks (or offsets) upto 152mm projection for 100 mm to 75 mm pipe complete all as specified and directed

S&F Stack clamps out of 50x 5mm flat iron & 16mm dia round iron stays (as per sample) including bolts & nuts & securing ends of stay to wall or roof for 75 mm dia of pipe complete all as specified and directed

M&L for 20mm thick cement plaster in cement mortar 1:4 on concrete surface finished even and smooth mixed with liquid WPC @ 0.200 ltr in 50 Kg of cement( or as per manufacturer instruction ) complete all as specified and directed. Note: Liquid WPC shall be measured and paid separately

M&L APP modified roof treatment over existing non-accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning surface properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufacture by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying APP modified water proofing membrane not less than 3.0mm thick weighing not less than 3.60 Kg/Sqm, reinforced with non woven polyster fiber weight not less than 160gm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. (d) Top of membrane shall be provide with solar reflective bituminous aluminum paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane.

Supply only liquid water proofing compound

M&L for cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in copings, kneelers, apex stones, bed plates, kerbs, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, etc . including necessary Use and waste of form work complete all as specified and directed.

M&L for 10mm thick plaster in cement mortar 1:3 finished even and smooth without using extra cement mixed with water proofing compound complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in surface channels & drainscomplete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner grith in cement concrete, using extra cement, including forms, moulds, mitred/stop ends etc complete all as specified and directed.

M&L for Factory made RCC manhole cover with frame of loading capacity 2.5- 35tonne of size exc 0.36 sqm but not exc 0.81 sqm each complete all as spd and directed.

M&L concrete bed to drain pipes including forming cradles in cement concrete 1:3:6 type C2 for 150 mm bore pipe complete all as specified and directed.

M&L 150 reinforced cement concrete pipes class NP2 with one collar per length of pipe complete all as specified and directed.

Cutting into existing manholes for connecting new drains ,making good to pipe (150 mm bore pipe or any size) and rendering , cutting out existing benching for forming branch channel (1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as requiredcomplete all as specified and directed.

M&L Rendering 10mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement mixed with WPC complete all as specified and as directed. Note: WPC will be measured and paid separately.

Use and waste of form work to curved faces of wall retaining walls, abutments, parapets, staircase railing and similar work including attached pillasters, buttresses etc vertical of to batter complete all as specified and as directed.

Use and waste of form work to edges of concrete flats, treads, , breaks in floors, openings in concrete walls, floors & roofs & sides of RCC/PCC bands in walls, horizontal or sloping, & similar work exc 20cm wide rough finished surfaces of concrete complete all as specified and as directed.

S&F 40mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling etc complete all as specified and as directed.

S&F in repair 40 mm size gun metal globe or gate valves with iron wheel head, screwed both endsfor iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down screwed for iron pipe of 40mm bore.

S&F Bands, straps, supports or stays for rainwater, ventilating pipe, including bolts if required hooks (stay) heavy, for large gates; hook and pintle hinges : large hasps and staples; chains hand made sliding bolts clamps; hold fasts;wall tie hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters;knee piece inserts; two way and three way straps, plate washers and similar small article conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Taking down chowkhats of frames exc 1.50 sqm but n. exc 4.0 sqm with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down shutters exc 1sqm but n. exc 2 sqm each complete all as specified and as directed.

Demolitin of brickwork built in cement mortar including all quions ,arches,pillars etc but excluding ashlar facings dressed stonework and pre cast concrete articles and removal of rubbish complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc. 15cm thickness (below or above ground level) and removal of rubbish complete all as specified and as directed complete all as specified and as directed.

M&L Reinforcement cement concrete M-25 ( Design mix) as in foundations including rafts, footings, foundations beams, plinth beams, bases for columns and basement slabs etc complete all as specified and directed.

All as per item 95 but in wall, retaining wall, basement wall, ballast wall and the like

All as per item 95 but in columns, pillars, piers, posts and struts etc

All as per item 95 but in beams, cantilever, bressummeres lintels over 1.50m spam

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, including flat rough finished surafaces of concrete complete all as specified and directed.

Use and waste of form work to sides of pillars, posts, struts, piers, columns, and stanchions, square, rectangular or polygonal in shape, including flat rough finished surafaces of concrete complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in skirting/dado/risers of steps etc set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match over backing coat of rendering 10mm thick in CM (1:4) including taking down cement plaster on walls etc complete all as specified and directed.

All as per item 101 but over screed bed or bedding layers of mortars 15 mm thick in CM 1:4 for laying floor finishes complete all as specified and directed.

Taking down and refixing steel window with side hang shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetaled or welded in same of other opening complete all as specified and directed.

Taking up or down steel water tubing and connections including cleaning for refixing or removal for bore of pipe 15mm bore complete all as specified and directed.

Refixing of old steel tubing 15 mm medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor etc all as specified

S&F in repair CI floor trap 100 mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with CP grating with ot without hole for waste pipe complete all as specified and directed.

S&F PVC(SWR) pipes 110mm bore, single socketd , in any length with rubber ring joints , in any length fixed to walls complete all as specified and directed.

S&F PVC (SWR) bend any radius 110mm dia bore complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in any position and any description and otherwie specifically provided for demolition and removal of rubbish complete all as specified and directed.

M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius for manhole/septic tank etc built in CM (1:4) complete all as specified and directed.

M&L concrete bed to drain pipes including forming cradles in cement concrete 1:3:6 type C2 for 200 mm dia pipe complete all as specified and directed.

M&L 200 reinforced cement concrete pipes class NP2 with one collar per length of pipe complete all as specified and directed.

Provn of Septic tank 300 Users including sludge chambers all as per TD drawings CE/TD-1202/2003 Sh 1/2 & 2/2, excavation and earth work in any type of soil, rest all as per drawing complete all as specified and directed.

Provn of Soakage well of size 3.6 M internal dia X 4.50M clear deep. excavation and earth work in any type of soil, rest all as per TD drawings CE/TD-1202/2003 Sh 1/2 & 2/2 complete all as specified and directed.

Taking down chowkhats of frames n.exc 1.50 sqm with shutters (without taking off shutters from the frames) all as spd.

Taking up or down steel tubing and connections, including cleaning for refixing of any description concealed/open 20mm bore complete all as specified and directed.

Diamantling of existing tanks, exc 500 ltrs and n.exc 1000 ltrs and removal from site complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing mentioned in SSR Part II complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 95mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube and fixing in opening complete all as specified and directed.

M&L Roughening of old concrete surfaces of floor by picking, sweeping clean and washing down with water to remove dust etc and brusing neat cement slurry with 3.00 kg per sqm complete all as specified and directed.

M&L 2nd class hard wood 35mm thick glazed and skeleton door shutters factory made, open rebated and prepared to receive glass or gauge etc with rounded, chamfered or mitred sash bars edges of framing plain chamfered or rounded fitted with cut and mitred beads and fitted to chowkats for securing glass/gauge, size of stiles rails and other parts as per clause 8.20 (a) of SSR Part-I 1991 (Larger size to be provided) complete all as specified and directed

S&F in repair 25mm bore Mild steel powder coated, single curtain rod (wall thickness not less than 1mm) including fancy type PVC powder coated brackets, one pair of decorative curtain rod bulbs (as per sample) etc suitable for single curtain rod, complete all as specified and directed

S&F in repair anodiesed Aluminium handle, oval type, stove enameled black 150 mm long complete all as specified and directed

S&F in repair anodiesed aluminium tower bolts, stove enameled black with 150 mm long bright bolt complete all as specified and directed

S&F Viterous china urinals, half stall type, including CP coupling, waste pipe and all necessary fittings, complete including providing and fixing plugs , bedding urinal against wall in CM 1:2 , securing urinal to PVC rawl plugs with and including 60mm long brass screws, pointing around urinal back in white cement complete all as specified and directed

S&F PVC flushing cistern 10 ltr capacity including suitable PVC connection, PVC flush pipe 32mm bore of polyethylene of low or high density complete including making necessary connections, jointing to WC complete all as specified and directed.

S&F in repairs CP grating 125mm dia heavy duty complete all as specified and directed

S&F 110mm bore PVC (SWR) pipe single socketed to any length with rubber ring joints and including bend and taking down old unservicable pipe of any size and description complete all as specified and directed

S&F PVC floor trap 100mm dia of out let with grating including jointing to waste pipe with solvant cement complete all as specified and directed

S&F PVC soil waste and vent pipe 100mm in any length with or without ears including jointing to waste pipe in solvant cement joint & fixed to wall complete all as specified and directed

Taking down cement plaster on brick walls or stone walls any descrition etc including raking out joints, hacking for key, scrubbing down with water etc and removal of rubbish complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and n exc 2 Sqm each, refixing in same opening after easing and adjusting complete all as specified and directed.

M&L Machine cut kota stone in flooring 18-20 mm thick over and including 20 mm thick cement screed base in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match including rubbing and polishing, moulding at edge if reqd complete all as specified and directed

All as per item 133 but in skirting,dado etc, over and including 10mm thick backing coat in cement mortar (1:4)

M&L Pre polished Granite slab work 20mm thick in steps, jambs, pillars, window cills, cooking plateform and like over 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using stone dust with admixture of pigment to match shade of granite complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, sockets, Brackets, ceiling roses, lamp holders, pendants, regulators, light fitting etc. removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L for point wiring using 3 x 1.5 Sqmm FRLS PVC insulated unsheathed /multi stranded copper conductor cable(Phase, neutral and earth wire) drawn through and including concealed conduit medium grade of dia not less than 20mm and 1.8mm thick and connected to common earth dolly with 3 mm thick plastic laminated sheet cover fixed with brass screws for mounting switch, socket, flan regulators etc including making connection of cable with MCBs through proper size copper/brass thimbles for one light/fan/exhaust fan point controlled by one 1 way switch complete all as specified and directed. Note: 1. Connections of cable with MCBs/Switch Sockets shall be done through proper size copper/brass thimbles. 2. Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit in not feasible. 3. Proper colour code will be used for wiring as per the electrical rule and as directed.

All as per Srl item No 137 here-in-before but for one 5 Amp socket outlet point on same board controlled by one switch SP, one way 5 Amp, 240Volts.

All as per Srl item No 137 here-in-before but for one 5 Amp socket outlet point on inependent board controlled by one switch SP, one way 5 Amp, 240Volts.

All as per Srl item No 137 here-in-before but with 3x2.5Sqmm for one 15 Amps Socket on independent board complete all as specified and directed.

S&F modular socket 6 Amp, 2/3 Pin multipurpose, 2 module, complete all as specified and directed.

S&F modular switch one way 6 Amp one module, front operated complete all as specified and directed.

S&F modular switch piano type flush button single pole 16 Amp one module, front operated.

S&F modular socket 6 Amp/16 Amp, 2/3 Pin multipurpose, 2 module, complete all as specified and directed.

S&F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 120W- 2 module including necessary connections complete all as spd and directed.

S&F ceiling rose PVC/polycarbonate, insulated body surface Bakelite 65mm dia three terminals.

S&F Lamp holder jumbo type, PVC/Polycarbonate type with back plate including 15W LED lamp complete all as specified.

S&F LED tube lights fitting 1x20W, 220V,AC white poder coated CRCA box type channel with decorative end cap alongwith LED T8 tubular lamp 20W linear with extruded aluminium/pc body and PC diffuser and inbuilt drive including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F Energy saving, surface mounted, bulk head LED luminaire 10 W with PDC aluminium housing and polycarbonate diffuser complete including connecting up with three core twisted flexible copper conductor cable of suitable size.all as specified.

S&F in replacement SPN MCB DB 8 way sheet metal enclosures double door 230 V AC, 50 Hz AC having copper bus bar of rating 200Amps complete all as specified and directed.

S&F in replacement SPN MCB DB 6 way sheet metal enclosures double door 230 V AC, 50 Hz AC having copper bus bar of rating 200Amps complete all as specified and directed.

S&F MCB SP 240V, 50Hz, 10 KA,of rating 6 to 32 Amp all as specified and directed.

S&F in replacement MCB SPN 240V, 50Hz, 10 KA,of rating 32Amp all as specified and directed.

M&L for earthing complete with G .l earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground ( earth pit not less than 2.25 m deep below GL ) with top edge of the plate not less than 1.5 m below the normal ground level connected galvanized earth lead wire 4.0 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel including necessary excavation & earth work in any type of soil, removing surplus soil to a distance not exc 50mtr, including PCC chamber in PCC (1 : 2 : 4), type B1, using (20 mm graded stone aggregate), mild steel frame made out of angle iron of size 40 mm x 40 mm x 6 mm thick duly painted with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer hinged with and including 6 mm thick Cl cover with handle , watering arrangement with funnel internally secured with wire mesh with 20 mm dia light grade GI pipe for watering, 15 mm dia medium grade Gl pipe for earth wire protection with and including alternate layer of charcoal dust and common salt. complete all as shown in electrical plate No 3 connected to DBs all as specified and indicated including testing on completion.

S&F XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sq mm 2core, laid under ground, fixed along wall, through GI pipe under floor/road including dismantling existing service cable of any size from electric pole to building, complete all as specified and directed.

All as per Item No 155 but size 16 Sq mm 4 core.

All as per Item No 155 but size 10 Sq mm 2 core.

S&F LED street light with pressure die cast aluminium housing with polycarbonate cover, finless design, dedicated peanut optics, > 100 lumen/W system efficacy, minimum 3000 system lumens, 30W system wattage (including driver), color temperature > 5700K, CRI>80,IP65 protection, IK07 rating. The potted electronic driver with THD<10%, PF>0.95 complete all as specified and directed.

S&F metallic exhaust fan AC single phase 230/240 Volts of size 300mm sweep, 900RPM double ball bearing type with louvers including grouting nut bolts and making the hole of suitable size by dismantling the existing wall and making good the disturbed surface in CM 1:3 to match with existing specifications of surface including connecting with 3core flexible copper conductor of 0.50 sq mm complete all as specified and directed.

S&F switch piano flush button single pole one way 5 amp 240 volts, all as specified and as directed.

S&F Socket outlet 2 in 1, 3 pin, 5 amps, flush type with shutters, 240 volts all as specified and as directed.

S&F switch 15 amps, flush type , 240 volts all as specified and as directed.

S&F Socket outlet 2 in 1, 3 pin, 5 and 15 Amp flush type, 240 volts all as specified and as directed.

S&F Decorative 07 Watt "2 feet'' LED mirror light with driver and wall mounting arrangment and all as specified and directed.

M&L for well burned bricks , laid flat ( old size) sub class B designation 75 for cable protection copmplete all as specifed and directed.

M&L for tube , light grade galvanised of 40 mm bore with all fittings laid in trenches/through wall / under road/floor or pole by means of FI clamps, nuts bolts and washers complete all as specified and directed.

S&F in replacement sub Main Wiring with two single core PVC insulated unsheathed multistranded flexible copper conductor cable of size 2x4 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor 4 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit complete and making good to disturbed surface of wall/floor with cement mortar and finishes to match existing surface all as specified and directed.

S&F in replacement sub Main Wiring with two single core PVC insulated unsheathed multistranded flexible copper conductor cable of size 2x6 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor 6 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit complete and making good to disturbed surface of wall/floor with cement mortar and finishes to match existing surface all as specified and directed.

S&F stepped type electronic fan regulator flush type Socket type on the existing phenolic laminated sheet etc. not less than 100 W flush type.

S&F sheet metal enclosures double door VTPN MCB DB 4 way 415 V AC, 50 Hz with 250Amps rated copper bus bar complete with IP 43, IK-09 protection suitable for flush mounting into the wall including MCCB 63Amps, 4P, 16kA breaking capacity with fixed magnetic and thermal setting of same make as of DB and making connection with cable by menas of suitable size of Al thimbles including makin good the disturbed surface and matching with the existing surface specification complete all as specifiedcomplete all as specified and directed.

Dismantling carefully of lightening protection Aluminium strip odd size along with insulators, nut bolts, GI pipe, lightening arrestor rods and PCC Blocks and removing material to store for keeping in safe custody and refixing the same in previous locations including necessary PCC work (1 : 2 : 4), type B1, using (20 mm graded stone aggregate) for grouting GI pipe complete all as specified and directed.

M&L for sand filling in trenches dry and and clean sand unwashed including punning around cable for protection of under ground cable complete all as specified and directed.

Supply and fix round shaped surface mounted 18Watt LED downlight luminaire with dome shaped high qaulity opal diffuser , inbuilt driver with efficacy 100Lm/W, CRI>80 with 5700+/-300K CCT complete all as specified and directed.

Supply and fix LED 7watt warm white picture light including bronze color metallic housing with mounting clips with efficacy 100Lm/W, CRI>80 with 5700+/-300K CCT complete complete all as specified and directed.

Deduct Total amount of SCHEDUL 'A' SECTION-II (SCH OF CREDIT) Rs 27,594.00 ( to be deducted from Schedule ‘A’ (BOQ) to arrive at the Contract Sum.

AV ENTERPRISES

M/s Rajeev Vashist