8440 SPECIAL REPAIRS TO SHIPS GALLEY (P- 32 ) INCLUDING SENIOR SAILORS AND JUNIOR SAILORS DINNING HALL AT INS UTKROSH UNDER GE MINNIEBAY PORTBLAIR

Amount

Taking down cement plaster on brick or PCC block masonry wall in any description complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the rubbish complete all as specified and directed by Engineer-in-Charge.

Taking down existing chowkats or frames n.exc. 1.5 Sqm each including iron mongeries complete all as specified and directed by Engineer-in-Charge.

Taking up or down old/chocked water tubings 15mm bore with fittings from trenches /walls and stacking at site complete all as specified and directed by Engineer-in-Charge.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-Charge.

Demolition of Brickwork or stone/ boulder masonry, built in Cement mortar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Taking up or down old/chocked water tubings 20 mm bore with fittings from trenches /walls and stacking at site complete all as specified and directed by Engineer-in-Charge.

Material and labour for APP modified waterproofing treatment over existing RCC roof slab with following specification including brushing off the surface to receive the treatment obtain the required surface and then providing 10mm screed bed with water proofing compound with required slope complete as directed :- (a) Applying bituminous primer @ 1.2 kg/Sqm on the prepared dry roof surface. (b) Laying 4mm thick APP membrane Plain finish weight not less than 3 to 4 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap and membrane shall be taken to the parapet through a fillet and shall be tucked inside up to height of 300mm.(c) Applying bituminous primer @ 1.2 kg/Sqm including one coat of aluminium paint over the top surface complete all as specified and directed by Engineer-in-Charge. [Note : The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane].

Disconnecting existing tanks, setting aside (or lowering if required) for hoisting if required reconnecting and re-fixing in position complete all as specified and directed by Engineer-in-Charge.

S & F in repairs Aluminium section (powder coated not less than 50 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, locking arrangements etc., complete with standard aluminium sections, complete all as specified and as directed by Engineer-in-charge. Note:- Weight of various Aluminium sections handles and locking arrangements shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, glass & aluminium wire cloth as applicable will be measured and paid separately as supplied only.

Supply only 5 mm thick sheet figured glass and glazing with rubber packing around the glass, in squares exceeding 0.50 sqm in each pane complete all as specified and directed by Engineer-in-Charge.

Supply only 12 mm thick Prelaminated particle board, exterior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge.

Supply only Aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10mm thick on fair faces of brick/concrete surface in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering to ceiling in 5mm thick on fair faces concrete surface in CM (1:3) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for external rendering 5mm thick in CM 1:4 with water proofing compound (water proofing compound shall be used as per manufacturers instructions) over a coat of 10mm thick in CM 1:6 over brick or concrete surfaces finished even and fair complete all as specified and directed by Engineer-in-Charge.

Supply only water proofing compound conforming to IS-2645,1975 complete all as specified and directed by Engineer-in-Charge.

M&L for oil bound distempering two coats over a coat of alkali resistant priming paint including preparation of new plastered surfaces of wall complete all as specified and directed by Engineer - in -Charge. Make : Asian paints tractor suprema

All as per Item No: 19 but on ceiling complete all as specified and directed by Engineer-in-Charge. Make : Asian paints tractor suprema

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed by Engineer-in-Charge. Make : Asian paints Apex suprema

M & L for Non Skid Ceramic Tiles, Coloured, of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 mm to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

All as per item No.22 here in before, but on vertical surfaces including 10mm thick CM 1:3 as in backing coat of dado/skirting complete all as specified and directed by Engineer-in-Charge.

M & L for Non Skid Ceramic Tiles, Coloured, of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 mm to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L Coloured Glazed ceramic tiles in vertical surfaces350X250X7mm/ 450X350X 7mm thick as in skirting /dado, set and jointed in cement slurry and pointed in coloured cement to match laid over 10mm thick cement backing coat in CM 1:3 complete all as specified and directed by Engineer-in-Charge.

M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

M&L for coloured heavy duty vitrified coloured tiles300X300X10 mm thick of each tiles in floor/ steps/stairs etc set and jointed with cera bond paste and pointed in coloured cement to match as in floor complete all as specified and directed by Engineer-in-Charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of rudraksh colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engineer in charge.

S & F 100 mm size, Butt hinges, Stainless Steel, Medium weight, bright polished including fixtures complete all as specified and directed by Engineer-in-Charge.

S & F 150 mm long Aluminium anodised barrel tower bolts of extruded sections complete all as specified and directed by Engineer-in-Charge.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and directed by Engineer-in-Charge.

Fixing only in repairs aluminium door/ window shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and as directed by Engineer in Charge

S&F stainless steel friction stay hinges 200 x19 x1.90 mm of standard size complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stainless steel friction stay hinges 200 x19 x1.90 mm of standard size complete all as specified and directed by Engineer-in-Charge.

M&L complete removal existing wall surface applying two coats of oil bound distemper over a coat of alkali resistant priming paint including preparation of new plastered surfaces of wall complete all as specified and directed by Engineer - in -Charge. Make : Asian paints tractor emulsion

All as per Item No: 36 but on ceiling complete all as specified and directed by Engineer-in-Charge. Make : Asian paints tractor emulsion

M & L for Preparation of old plastered wall surfaces and applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm complete all as specified and as directed by Engr-in-Charge. Make : Asian paints Apex suprema

M&L for two coats of synthetic enamal painting over one coat of primer for new or previsouly untreated Surfaces of any description over 10cm girth or width complete all as specified and directed by Engineer-in-Charge.

S & F Mild steel work in tubular /post/trusses/purlin including special shaped washers base and bed plate cleat nut and bolt etc confirming to IS 1161- 1979 graded St 240 complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel work in Stairs (framed) including stringers, treades, landing balusters, hand rails etc. including cleats brackets Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-Charge.

S&F Framed work such as grills gratings, etc with ends of bars shouldered and/or riveted,or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer-in-Charge.

M&L for Mild steel Plates (Plain or Chequered) channels, square or notched (Ordinary and counter sunk) forming holes, without any attachment of Fe 290 (Gde E-165) complete all as specified and directed by Engineer-in-Charge.

S&F for aluminium anodised snap grid false ceiling of standard aluminium section such as wall angle of size 38mm x 25mm x 2.4mm weighing 0.36 Kg/Rm main/cross tees of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/Rm, grid size n.exc. 610 x 610mm suspended with 4mm dia GI wire at interval n.exc. 600mm centre to centre for main & cross tees fixed to roof slab roof truss fixed with suitable size MS hook and fastening bolts etc including 'E' board classic 4mm thick oceanic sheet of size n.exc. 610 x 610mm size fixed in ceiling with clips to aluminium snap grid complete all as specified and directed by Engineer-in-Charge.

S&F in repairs curtain rod / harrison rails mild steel chromium plated with fixed brackets , stops, rollers etc, 25 mm dia with fixed brackets , stops rollers etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs mild steel chromium plated brackets suitable for curtain rod 25 mm dia complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm outer dia CPVC pipes of pressure rating 10kgf/cm2 fixed complete all as specified and directed by Engineer-in-Charge.

All as per item no 47 above but 20 mm bore pipe complete all as specified and directed by Engineer-in-Charge.

Supplying and laying of CPVC pipes 32mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engineer-in-Charge.

S&F CPVC Brass Elbow 16 mm outer dia complete all as specified and directed by Engineer-in-Charge.

S&F CPVC Brass Tee 16 mm outer dia complete all as specified and directed by Engineer-in-Charge.

S&F CPVC Brass Tee 20mm outer dia complete all as specified and directed by Engineer-in-Charge.

S&F CPVC Brass Elbow (3/4 X ½) 20mm outer dia complete all as specified and directed by Engineer-in-Charge.

S&F CPVC Brass union 16 mm outer dia complete all as specified and directed by Engineer-in-Charge.

S&F CPVC Brass union 20 mm outer dia complete all as specified and directed by Engineer-in-Charge.

S & F in repairs Two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs chromium plated health faucet with 1000mm PVC pipe for 15 mm bore with fittings complete all as specified and directed by Engineer-in-Charge.

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engineer-in-Charge. Note:- Removal of doors (any type ) inclusive also in this rate

S&F in repairs 15mm Chromium Plated Bib Tap long body fancy type heavy duty with wall flange complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass chromium plated over head shower rose with arm 125 mm size with long body with swivel joint including fixing to steel pipe or union, complete all as specified and directed by Engineer-in-Charge..

S & F in repairs Angular cock 15 mm dia, cast copper alloy with capstan head, screwed down high pressure with long shank and cup fancy type for iron pipe etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair Corner glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern) EWC white in colour with and incl plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 10 Liters capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia including brackets and connections to pipe complete all as specified and directed by Engineer-in-Charge.

S & F in repairs Vitreous china ware wash hand basin, white, flat back of size 550 mm X 400 mm including 32mm brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 20 mm brass chromium plateds towel rail of 20mm dia and 600mm in length 'D' shaped between flanges complete all as specified and directed by Engineer-in-Charge.

S&F in repairs for powder coated aluminum peg set of 4 solid body complete all as specified and directed by Engineer-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws asspecified complete all as manufacturers instruction complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium wind ties for roof including all necessary drilling, bolting or rivetting fixed with GI self tapping screws as specified for roof sheeting complete all as specified and directed by Engineer-in-Charge.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer on steel surfaces of any description, over 10 cm width or girth, not otherwise described including preparing new steel surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for precast cement concrete block masonry with PCC solid blocks in 1:3:6 type C1 using 20mm graded stone aggregates, exc. 10cm in width and set in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M & L for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick PCC 1:3:6 type C1 Nominal mix using 20mm graded stone aggregate as in plinth protection laid in panels with joint strips and finished even and smooth with using extra cement including formwork complete all as specified and directed by Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light, Fan, Socket or power) complete, fitting such as switches ceiling roses, pendants, regulators, Sockets etc including conduit, sunken box etc removing unservicable materials at site and making good disturbed surface to match with existing finish with plaster and applying white / colour wash / OBD / CBP as per existing at site as required of walls, floors roofs etc complete all as specified and directed by Engineer-in-Charge.

M & L point wiring with 1.5 Sq.mm (nominal area) PVC unsheathed multi strandard copper conductor PVC insulated 1100 volt FRLSH grade multistranded cable drawn through and including PVC casing capping/conduit ISI marked minimum 20mm size and its accessories complete along with 1.5 Sqmm FRLSH cable but in green colour as continuous earthing wire and connecting to common earth dolly completely concealed ,surface, in walls/ceiling/roofs with and including 1.2 mm thick MS sheet terminal boxes duly fabricated flush mounting in the wall for mounting switches, switch socket combinations fan regulators etc., as required with 3 mm thick plastic laminated sheet top cover complete all as specified and directed by Engineer-in-Charge for the following:-

One light /fan/bell point controlled by one 05/06 amps switch complete all as specified and directed by Engineer-in-Charge.

One 5/6 Amps plug point independent board controlled by one switch complete all as specified and directed by Engineer-in-Charge.

One three pin switch socket 5/6 Amps plug point on same board complete all as specified and directed by Engineer-in-Charge.

All as per item No-77 herein before but with 2.5 Sqmm single core multi stranded FRLSH copper conductor for one three pin socket 5 Amps on independent board including continuous earth wire PVC insulated 2.5 Sqmm FRLSH copper solid conductor to common earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No-77 herein before but with 4 Sqmm single core multi stranded copper FRLSH conductor for one three pin socket 5 Amps on independent board including continuous earth wire PVC insulated 4 Sqmm copper FRLSH solid conductor to common earth dolly complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 2/3 pin 5 Amps 240 volts flush type complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 3 pin 5/15 Amps 240 volts flush type complete all as specified and directed by Engineer-in-Charge.

S&F switches 6 Amps 240 volts flush type complete all as specified and directed by Engineer-in-Charge.

S&F modular switches 16 Amps 240 volts flush type complete all as specified and directed by Engineer-in-Charge.

S&F Fan step regulator, 120W - 1/2 module ,220V 50Hz complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of sheet metal enclosure with socket plug top , single pole and neutral enclosure with two pin earth plug and socket complete with one MCB SP of capacity 20 to 32 Amps complete all as specified and directed by Engineer-in-Charge.

S&F in replacement BLDC ceiling fan HS décor 5 star rating , 1200 mm Sweep 240 volt , Opal . White/brown including rod minimum length 1.5 m and bush , nut bolts , capacitors including driling on roof and fixed 1 to 1.5 feet rod and connecting bolts etc including removing and depositing of old unserviceable ceiling fan complete all as specified and directed by Engineer-in-Charge.

S&F in replacement turbo force heavy duty Exhaust fan , 450 mm Sweep 240 volt , 1400RPM,Opal . White/brown including making hole suitable size for fixing 450 mm sweep exhaust fan making good distribution and after fixing exhaust fan flap cover to be fixing on behind exhaut fan hole , nut bolts , capacitors including all accessories including removing and depositing of old unserviceable exhaust fan complete complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Exhaust fan , 600 mm Sweep 240 volt , 1400RPM,Opal . White/brown including making hole suitable size for fixing 600 mm sweep exhaust fan making good distribution and after fixing exhaust fan flap cover to be fixing on behind exhaut fan hole , nut bolts , capacitors including all acessories including removing and depositing of old unserviceable exhaust fan complete all as specified and directed by Engineer-in-Charge.

S&F in replacement single phase, 230 volts, 50 Hz, wall mounted fan, 450 mm sweep make-Havells V3 , fixing on wall with fan clamp/hook, connecting electrical accessories including depositing old unserviceable fan to store yard all as directed by the Engr-in-charge.

S&F in replacement of ceiling rose, surface bakelite 65 mm x 30 mm, 3 terminals complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of LED tube light fitting, 1x20 w, 230v .Surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver.Flicker free, high efficiency and robust industrial batten family suitable for Surface, Wall and Conduit mounting. The product family offers dimmable and connected batten option & connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of DB SPN 8 way with category of protection double door type IP-42 factory made with tinned copper 200 Amps rated bus bar suitable for MCBs,complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of MCB SPN 32 Amps working on 415 volts 50 Hz AC supply,10 KA C series complete all as specified and directed by Engineer-in-Charge.

S&F in replacement of MCB single pole 5 to 32 Amps working on 240 volts 50 Hz AC supply,10 KA 'C' series complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring with PVC Insulated unsheathed Cable 2 runs of 1.5 Sqmm multistranded FRLSH copper conductor 1100 Volt grade IS-694 and drawing in and including steel conduit stove enamelled medium grade suitable dia with fixing materials, sunken terminal MS boxes of 2mm thick, laminated sheet cover 3mm thick and including provision of earth wire PVC insulated unsheathed 1.5 Sqmm stranded FRLSH copper conductor single core cable connected to common earth dolly all as specified and directed by Engineer-in-Charge for the following:-

One light/fan point controlled by 5/6 amps one way switch complete all as specified and directed by Engineer-in-Charge.

S&F in replacement flameproof LED tube light 2x16W flame proof type FLP-WP, CMRI certified recommended for gas/vapour group of IIA & IIB, Zone 1 & 2 and IP 65 protection with die cast alluminum hosing with heat resistant toughened glass with LED tupe light fixture driver, holders, connectors etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable drawn through steel enamelled flexible conduit with suitable size complete all as specified and directed by Engineer-in-Charge.

S&F in replacement flame proof Exhaust fan , 380 mm Sweep 240 volt,1440 RPM,Opal. White/brown.CMRI certified recommended for gas/vapour group of IIA & IIB, Zone 1 & 2 and IP 65 protection with die cast alluminum hosing including making hole suitable size for fixing 380 mm sweep exhaust fan making good distribution and after fixing exhaust fan flap cover tobe fixing on behind exhut fan hole , louvers, wiremesh, nut bolts, metalic conduit, capacitors including all accessories complete all as specified and directed by Engineer-in-Charge.

S & F in replacement switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as specified and directed by Engineer-in-Charge. by Engineer-in-Charge.

M&L for Sub main wiring complete with 2x1.5 sqmm , single core , multi stranded copper conductor FRLSH PVC insulated and sheathed cable 1100 Volts grade , drawn in PVC Casing Capping in surface /PVC conduit in concealed/surface (as required) along walls roofs etc including 1.5 sqmm size PVC insulated unsheathed FRLSH copper earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed by Engineer-in-Charge. Note:- (i) all three wire/cable(phasé, neutral and earth) should be run through for each individual circuit from the DBs. (ii)Two run of cable and earth conductor be measured as one length)

All as per Serial item No- 99.00 but 2X2.5 Sqmm and 1X 2.5Sqmm for Earth wire complete all as specified and directed by Engineer-in-Charge.

All as per Serial item No- 99.00 but 2X4 Sqmm and 1X 4Sqmm for Earth wire complete all as specified and directed by Engineer-in-Charge.

All as per Serial item No-99.00 but 2X6 Sqmm and 1X 6Sqmm for Earth wire complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 2000 litre all as specified in SSR Part I complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 litre complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 litre all as specified in SSR Part I complete all as specified and directed by Engineer-in-Charge.

S&F in repair Ball brass valves,high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 25mm size complete all as specified and directed by Engineer-in-Charge.

S&F in repair Ball brass valves,high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed 50mm size complete all as specified and directed by Engineer-in-Charge.

S&F in repair 25 mm Gun Metal, globe or gate valves with iron wheel head, ISI marked screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair 50 mm Gun Metal, globe or gate valves with iron wheel head, ISI marked screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair 25 mm GI tubes medium grade ISI marked galvanized with all fittings , laid in trenches/fixed on wall/on roof etc complete all as specified and directed by Engineer-in-Charge Notes :- Necessary earthwork will be measured and paid separately in relevant item.

S&F in repair 50 mm GI tubes medium grade ISI marked galvanized with all fittings , laid in trenches/fixed on wall/on roof etc complete all as specified and directed by Engineer-in-Charge Notes :- Necessary earthwork will be measured and paid separately in relevant item.

Excavation in trenches, not exceeding 1.50m wide and not exeeding 1.50m in depth for foundations, trenches of cable or pipe lines etc or and getting out in soft / loose soil complete all as specified and directed by Engineer-in-Charge.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated materials (soil) to a distance not exceeding 50 meters and depositing where directed at a level not exceeding 1.5 meters above the starting point complete all as specified and directed by Engineer-in-Charge.

Cutting the existing CI / DI /GI pipe line of size upto 150mm bore after through inspection of pipe line including disconnecting / dismantling and making arrangement for the new connection and making good all as specified and directed by Engineer in charge. Note : Necessary excavation and earthwork shall be deemed to be included in this quoted rate.

Supply, laying and testing in repair cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core complete all as specified and directed by Engineer-in-Charge. Note : Necessary earthwork and excavation shall be measured and paid in the relevant item of this schedule.

Supply, laying and testing in repair cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor with lux of suitable size of size 95 sq mm 3.5 core complete all as specified and directed by Engineer-in-Charge. Note : Necessary earthwork and excavation shall be measured and paid in the relevant item of this schedule.

Supply, laying of Telerex DWC (double Wall corrugated) HDPE pipe ISI marked of outer dia of 110 mm and inner dia 95 mm polethylene including couplers, bends, cap etc., with smooth internal and profiled external surface for non pressure under ground cable complete all as specified and directed by Engineer-in-Charge. Note : Necessary earthwork and excavation shall be measured and paid in the relevant item of this schedule.

S&F in replacement of vertical DB TPN 8 way IP 54 IK-09 with metal double door suitable for Provision of MCCB FP, 36 KA 125 Amp for housing of MCBs complete all as directed by Engineer-in- Charge.

S&F in replacement of MCCB TPN 125 Amps, 440 Volts, 36 kA, 'C'Curve complete all as specified and directed by Engr-in-Charge.

S&F in replacement of MCB TP 25 to 63 Amps, 440 Volts, 10 kA, 'C'Curve complete all as specified and directed by Engr-in-Charge.

S&F in replacement of MCB SPN 40 to 63 Amps working on 415 volts 50 Hz AC supply,10 KA 'C' series including taking out old one complete all as specified and directed by Engineer-in-Charge.

M&L for earthing complete with Galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanized earth strip 25x4 mm size connected by means of bolts, nuts, check nuts and washer of galvanized iron or steel, provision of 40mm dia GI pipe medium grade for protection of GI earth lead and 20mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) , type CI chamber. MS funnel, wire gauge. 50 mm thick RCC 1:2:4, type B1 earth pit cover with 6 Nos. 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No 3 of schedule Part-I. Note: (i) Cost of GI earth lead and GI protection pipe upto 7.5m length shall be deemed to be included in the rate quoted for this item.(ii) The unit rate shall also includes for Wire mesh, funnel, excavation, returninng & filling, PCC chamber pit, RCC cover & test point.(iii) All accessories required for galvanised steel plate electrode required, as specified and as directed.

KRISHNA TRADING COMPANY (BID ID -3089713)

M/S KHUSHICONSTRUCTION (BID ID -3083251)