Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹81.2 LAccepted-AOC 138 W NO 8A GURU TEG BAHADUR NAGAR DHURI DISTRICT SANGRUR | DHURI | SANGRUR | PUNJAB | ₹81.2 L | 1 | Accepted-AOC lowest and singal bid |
Tender Value
₹82.6 L
EMD Value
₹1.7 L
Closing Date
4 Dec 2025, 3:00 pmClosed
Er. Jasbir Singh Executive Engineer
EXECUTIVE ENGINEER CONSTRUCTION dIVISION PWD Br FATEHGARH SAHIB
Special Repair to Nandpur to Dadiana Road Under 2022-23,2023-24,2025-26 Programme falling in MC Bassi Pathana Distt. Fatehgarh Sahib (Left Over Rural Link Roads Under S/R Programme NIDA Project)
2025_CEPW_153861_2
no 8 Dated 30.10.2025
Open Tender
Civil Works - Roads
150 days
Distt Fatehgarh sahib
Please refer Tender documents.
4 documents required · 4 mandatory
₹5,000
₹1.7 L
5 May 2026
27 Nov 2025
4 Dec 2025
27 Nov 2025
4 Dec 2025
27 Nov 2025
Making 50 mm x 50 mm furrows Making 50 mm x 50 mm furrows 45 degree to the centre line of road and at one metre interval in the existing bituminous wearing coarse including sweeping and disposal of excavated material within 1000 meters lead complete as per technical clause 404 of MORT&H specifications (Full surface area will be measured for payment.)
Dismantling of existing road crust containing stone pitching or soiling. (50 mm to 150 mm thick).
Dismantaling of brick work /tile masonary or tile lining. (i) Dismantaling of dry brick work
Brick on End Edging Providing and laying of brick on end edging 6.83 cm wide, 11.11cm long and 22.86 high half brick deep including excavation, refilling and disposal of surplus earth up to 50 mtr complete as per Punjab PWD specifications.
Relaying of recovered material obtained from dismantled road material obtained from road crust compacting with vibratory roller to achieve the desired density, complete as per MORD technical specifications
Construction of granular sub-base by providing material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per MORD technical specifications
Water Bound Macadam Grading I (without screening for low volume Roads/undersigned Providing, laying, spreading and compacting stone aggregates of Grading I to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical specifications
Water Bound Macadam Grading II (without screening for low volume Roads/undersigned Roads Providing, laying, spreading and compacting stone aggregates of Grading II to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical specifications
Surface Dressing Providing and laying surface dressing in single coat using crushed stone aggregates of specified size on a layer of bituminous binder VG-10 @ 1kg per sqm laid on prepared surface after cleaning the road surface and rolling with 8-10 tonne smooth wheeled steel roller complete as per technical clause 509 of MORT&H specifications
Tack coat with Bitumen VG-10 Providing and applying tack coat with penetration grade bitumen VG-10 using bitumen pressure distributor at the rate of 0.40 kg per sqm on the prepared bituminous surface/granular surface treated with prime coat after cleaning the surface complete as per technical specifications
Open - graded premix Providing, laying and compaction of open - graded premix surfacing of 20 mm thickness consisting of crushed stone aggregates of specified grading premixed in a Continuous type hot mix plant with bituminous binder VG-10 @ 1.46kg per sqm, laid with Paver Finisher Mechanical and rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades complete as per technical clause 510 of MORT&H specifications
Seal coat Providing and laying of premix sand seal coat premixed in Continuous type hot mix plant using specified fine aggregates and penetration grade bitumen VG-10 @ 0.68kg per sqm, laid to the specified levels, grade and cross fall complete as per technical clause 511 of MORT&H specifications
Cement concrete 1:6:12 With stone aggregates 20mm gauge mixing by mechanical means using concrete mixer volumetric type
Providing and laying factory made rubber moulded smooth finish cement concrete Kerb M-20 grade 250mm high with bottom width 165mm and top width 115mm made over strong vibratory table and fixing with cement mortar 1:2 as per MORT&H specifications
Providing and laying 60 mm thick factory madecement concrete interlocking Paving blocks of M-35 grade manufactured by block makingmachine equipped with steel mould clamped to astrong vibratory table with hydraulic pressure forcompaction of concrete as per IRC SP 63 -2014and of approved size and design / shape laid inOrdinary Grey Colour and pattern over andincluding 40 mm thick compacted bed of coarsesand, filling the joints with fine sand etc, allcomplete as per directions of Engineer-in-Charge
Earth work undressed Kassi work undressed involving an average horizontal throw up to 2 metres and average vertical lift up to 0.5 metres
Providing and making rumble strips 15-20mm high at centre, 250mm wide placed at 1m centre to centre over freshly laid bituminous layer by using close graded premix surfacing material type B at approved locations to control speed. The close graded premix surfacing material type B shall conform to technical clause 512 of MORT&H specifications
Road marking with hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 0.25kg per sqm area as per IRC:35 1997 complete as per technical clause 803 of MORT&H specifications
Moulded Shank Road Stud Supplying and fixing of single mould twin shank reflective road studs made out of polycarbonate/ABS moulded body and reflective panels with micro prismatic lens or Glass Beeds capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values shall be as given in the detailed specifications and the product shall conform to ASTM D4280. The raised pavement marker shall also meet all the testing conditions of ASTM D4280 and fixed to the road surface using the adhesive. Two cylindrical Polymer Shanks of not less than 20 mm diameter and not less than 30 mm length shall be molded in the RPM body. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280. The marker shall withstand flexural strength of 909 kgf force in accordance with ASTM D4280. Marker lenses shall be moulded of Polycarbonate or methyl methecrylate conforming to ASTM D788. The supplier shall provide a 2 years warranty for satisfactory field performance as per clause 804.7.3 of MORT&H 5th revision specifications.
(i) Brick Bat
(ii) Bricks
Add Culture Cess @ 1%
Maintenance Work
Routine Maintenance of construction work as per periodicity to routine maintenance mentioned in the technical specifications. (For 2nd Year)
Routine Maintenance of construction work as per periodicity to routine maintenance mentioned in the technical specifications. (For 3rd Year)
Routine Maintenance of construction work as per periodicity to routine maintenance mentioned in the technical specifications. (For 4th Year)
Routine Maintenance of construction work as per periodicity to routine maintenance mentioned in the technical specifications. (For 5th Year)
Add Culture Cess @ 1%
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.54 MB
BOQ_313391.xls
BOQ • 0.31 MB
RecallnadpurSBD.pdf
Tender Documents • 24.65 MB
Download all tender documents and submit your bid