SPECIAL REPAIRS OF BLDG NOS T- 156 AND T- 182/2 AT ILP LOC AND PROVN OF CHAIN LINK FENCE AT GHODAGHAR LOC, TA MADRAS AT BRICHGUNJ MIL STN, PORT BLAIR

Amount

Excavation in post holes (or similar holes) each not exceeding 0.5 cum getting out in Hard/dense soil, returning filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25cm watering and consolidating and removing surplus soil to a distance not exceeding 50m and making good surfaces complete all as specified and as directed.

Material and labour for hard core of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Dismantling corrugated steel sheeting, any gauge, thickness, including removing L-type or J-type bolts in Roof Covering complete all as specified and as directed.

Taking down chowkat with shutter n.exc 1.5 Sqm without taking off shutters from the frame complete all as specified and as directed

Taking down chowkat with shutter exc 1.5 Sqm but n exc 4 sqm without taking off shutters from the frame complete all as specified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

Demolition of cement Concrete is ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed

Material and labour for 75mm thick Cement concrete in (1:3:6) Type C1 using 20mm graded stone aggregate as in plinth protection and finished even and smooth with using extra cement complete all as specified and as directed.

Material and labour for 100mm thick PCC (1:3:6) Type C-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and as directed.

Material and labour for 100mm thick PCC (1:2:4) Type B-1 using 20mm graded stone aggregate as in sub base of floor complete all as specified.

Material and labour for PCC 1:3:6 Type C2 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour for reinforced cement concrete 1:2:4 Type B1 (using 20mm graded stone aggregate) in precast posts, fencing posts, straining or terminal posts, struts etc, for fencing, (including form work) average sectional area exc 100 sqcm and n.exc 250 Sqcm complete all as specified and as directed.

Material and labour for high strength corrosion resistant CRS TMT bars 10mm dia and over cut to length, bent to shape required including cranking and bending spirally for hopping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.90mm dia) or securing with clips complete all as specified and as directed.

All as per item No 13 above but 5 to 10 mm dia bars as in stirrups, spacer etc

Material and labour for oil bound distempering two coats including complete removal of old decorated, plastered or unplastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.

Material and labour for two coat of weather proof exterior acrylic emulsion paint with anti-fungal property over a coat of primer including complete removal of old decorated, plastered or unplastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.

Material and labour for applying two coats of cement base paint over a coat of primer on new plastered untreated surfaces on walls including preparation complete all as specified and as directed.

Material and labour for Synthetic enamel paint of two coats over a coat of pink primer incl preparation of new wooden surfaces over 10 cm width or girth complete all as specified and as directed

Material and labour for preparation of new steel surface exc 10cm width or girth and applying one coat of red oxide primer and two coat of synthetic enamel paint glossy complete all as specified and as directed.

Material and labour for preparation of new steel surface not exc 10cm width or girth and applying one coat of red oxide primer and two coat of synthetic enamel paint glossy finish complete all as specified and as directed.

Material and labour for Plates (Plain or Chequered) channels, square or notched (Ordinary and counter sunk) forming holes, without any attachment of Fe 290 (Gde E-165) completely all as specified and as directed by Engineer in Charge.

Supply and fix steel work in tubular for columns, roof truss, purlins, rafters and battens etc incl special shaped washer etc complete using ERW or induction but welded tube conforming to IS : 1161-1979 Gde St-240 completely providing in any curvature and as of any shape etc complete all as specified and as directed by Engineer in Charge

Supply only mild steel angles, bars, flats etc as in supports for stiffening of fencing, wall ties, hold fasts, clamps and similar small articles confirming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply only mild steel bolts with hexagonal or square head one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut exc 5 cm long n.exc 10 cm long dia metre of neck exceeding 11 to 15 mm complete all as specified and as directed.

Material and labour for mild steel grade Fe 410W (grade E-250) quality B as in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

Supply and fix Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in ridges to wall, fixed with self-tapping screws as specified

Supply and fix Pre-painted galvalume aluminium zinc coating GI based corrugated/semi corrugated sheet 0.50mm thick as per approved profile, coloured, having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self-tapping screws all as specified

Material and labour for false ceiling with aluminium grid work (size of grid 605x605mm) with 35x25x1.5mm main tee and 25x25x1.4mm, cross tee and wall angle and suspended with 3.15mm dia, GI wire, hooked to roof with needful adjustment bolts at an interval of 1.20m, centre to centre staggered and board with Eco board, decorative type, size 600x600x4mm thick, finished with two coats of oil bound distemper over a coat of primer on exposed surfaces, complete all as specified and as directed by Engineer-in-Charge.

Material and labour for non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm and not exceeding 0.38 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles over 20mm thick screed bed in CM 1:6 complete all as specified and as directed

All as per item No 29 here in before, but on vertical surfaces incl 10mm thick CM 1:3 as in baking coat of dado/skirting

Material and labour for Chequerred cement concrete tiles, with grey cement and pigment 30cm x 30cm x 20mm thick, set, jointed and pointed in neat cement slurry in floors including 20mm thick screed bed in CM (1:6) complete all as specified and as directed

Supply and fix 35mm thick 2nd Class hard wood glazed/and skeleton shutters open rebated and prepared to receive glass/gauze etc. (without sash bars) edges of framing plain chamfered or rounded fitted with cut amd mitred beads for securing glass gauze etc. and fitted to chowkats etc. complete all as specified and as directed

Supply and fix 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed

Supply and fix Second class hard wood plain, solid, straight chowkats and frames, wrought framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed

Supply and fix Aluminium anodised (minimum anodisation is 15 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, locking arrangement etc, complete with standard aluminium sections, all as specified and as directed by Engineer-in-charge.(Aluminium section shall be of make Jindal/Hindalco/ Indalco). (Note:- Weight of various Aluminium sections shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, aluminium wire cloth as applicable will be measured and paid separately as supplied only).

Supply only 4.0mm thick Sheet glass ordinary quality and glazing with oil putty in Square n.exc 0.5sqm in each pane complete all as specified and as directed

Supply only 4.0mm thick Sheet glass ordinary quality and glazing with oil putty in Square exc 0.5sqm in each pane complete all as specified and as directed

Supply only 12 mm thick pre-laminated particle board, exterior grade, pre-laminated on both side with decorative choice lamination fixed with aluminium beading as in door panel complete all as specified and as directed.

Supply and fix aluminium fly proof mesh 0.45mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium straps complete incl taking down complete all as specified and as directed.

Supply and fix Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as specified and as directed

Supply and fix 150mm long extruded aluminium alloy anodised handles fabricated type, anodised complete all as specified and as directed.

Supply and fix Butt hinges, 100mm length extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21, complete all as specified and directed by Engineer-in-Charge.

Supply and fix Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips of sheet cast or extruded sections and fixing bolt or cast aluminium alloy & fixed complete all as specified and as directed.

Supply and fix Aluminium Die cast Body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and as directed

Supply only PVC coated (1mm thick) chain link fencing exc 2.00 but n.exc 3.50 kg per sqm with size of mesh 50 x 50 mm and thickness of wire n.exc 2.83 mm complete all as specified and as directed.

Fixing only PVC coated chain link fencing including fixing of line wires any mesh, size and any type of standards, rails, straining bolts etc including provision of binding wires complete all as specified and as directed. Note: Supply of MS line wire and flat iron bolt & nuts measured and paid separately

Supply only 6mm dia wire PVC coated for support / line wire to chain link fencing complete all as specified and as directed.

Taking down carefully aluminium point wiring (light, fan, socket or power) DBs complete and making good disturbed surfaces of walls, floors, etc, all as specified and as directed.

Material and labour for Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC casing and caping and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable green in colour as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets, fan regulators etc., all as specified and as directed for one light point controlled by one one way switch.

All as per item No. 49 here - in - before but for one fan point controlled by one 5 Amps switch with 1.5 sq mm copper conductor cable.

All as per item No. 49 here - in - before but for 5 Amps switch socket point on the same board controlled by one switch.

All as per item No. 49 here - in - before but for 3 pin switch socket outlet point 5 amps on independent board.

All as per item No 49 here-in-before but for 3 pin 15 Amps switch socket combination on independent board with 4 sq mm copper cable and provision of 4 sq mm FRLS PVC insulated stranded copper conductor cable for earth continuity conductor connected to common earth dolly connecting upto fittings

Supply and fix switch piano flush button single pole one way 5 amp complete all as specified and as directed.

Supply and fix switch socket outlet 3 & 2 pin (multi pin) 5 amp flush type complete all as specified and as directed.

Supply and fix switch socket outlet multipurpose 3 pin 15 and 5 amp controlled by one switch, flush type complete all as specified and as directed.

Supply and fix ceiling rose surface Bakelite 65x50mm 3 terminal complete all as specified and as directed

Supply and fix fan speed regulator, electronic suitable socket type for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge. Make:-Anchor/Havells/Bajaj

Supply and fixing energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core sheathed cable from fitting to ceiling rose complete all as specified and as directed. Make : Phillips Cat No BN021C LED20S PSU CDL/NW GR or eqvt in make of Bajaj/Wipro.

Supply and fix 25W New generation energy saving & environmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs as light and electronic driver complete with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete all as specified and as directed. Make: Philips cat No BRP020 LED HP/CW 240V 25Wor equivalent model of Bajaj/Wipro / CG

Dismantling and taking down ceiling fan 1200 mm sweep and refixing/connecting up including provision of cable from ceiling rose or connector to fan and Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including preparing, filling cavities with filler, one coat after cleaning all dust etc complete all as directed

Supply and fix in repair metal enclosure distribution board SPN, 4 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, including taking down old MCB/DB,Make : Havells /Legrand/C&S/L&T complete all as as specified and as directed.

Supply and fix in repair metal enclosure distribution board SPN, 8 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, including taking down old MCB/DB,Make : Havells /Legrand/C&S/L&T complete all as as specified and as directed.

Supply and fix in repair MCB single pole 240 volts, 6 to 32 amps "B" series complete all as specified and as directed by Engineer-in-Charge Make : Havells /Legrand/C&S/L&T

Supply and fix in repair single pole and netural 240 Volts 6 To 32 amps complete all as specified and as directed by Engineer-in-Charge Make : Havells /Legrand/C&S/L&T

Material and labour for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less thab 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part – I complete all as specified and as directed

Supply, lay, test and commissioning underground XLPE insulated and PVC sheathed, armoured heavy duty underground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 C x 6 sq mm complete all as specified and as directed

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers, bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out Soft/loose Soil complete all as specified and as directed

Returning, filling in, including spreading, levelling watering and well ramming in layers not exceeding 25cm complete all as specified and as directed

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed

SK ENTERPRISES

Ravi Enterprises

RPG AND COMPANY

Priya construction

T.THIYAGARAJAN

AMR TRADERS

M/S AMK CONSTRUCTIONS