SPECIAL REPAIR TO BLDG NO P-42 AND P-45 AT LGJ MIL STN

Amount

Dismantling of brick tiles in floor or roof laid dry and pointed in cement mortar complete all as specified and as directed.

Demolition mud in roofs, any thickness, including plastering and leeping complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles all as directed.

Demolition of reinforced cement concrete of slab, manholes covers, platform, granite tiles of any description and in any position all as specified and directed.

M&L for reinforced cement concrete type B0, 1:2:4 (12.5 mm graded stone aggregate) as in chajjas, slab, projection complete all as specified. Note : Reinforcement shall be measured and paid separately.

M&L for 40 mm thick cement concrete type B0, 1:2:4 (12.5 mm graded stone aggregate) as in roof padding and laid in slope 1:30 complete all as specified.

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm as in roof including cleaning surfaces all as specified and directed

M & L APP based membrance minimum weighing 3 KG per sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by torced application with APP membrane over 10mm thick screed bed in CM 1:3 mixing of WPC in mortar complete all as specified & directed.

M & L for cement concrete tiles 25cm x 25cm x 22mm thick, m a c h i n e pressed; over cement screed base laid over cement screed base laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment and no pigment in floors/roof, and cut and polished complete all as specified and directed.

Providing and Applying rising damp proof coating system with single component ready to use damp proof coating 1. Preparation :- Throughly brush and clean all laitance, loose particles such as dirt, grease, mortar droppings, release agents, efflorescence, bird droppings, etc all large voids and hallow portions must be removed and re-plastered non moving cracks having width upto 5mm must be filled with polymer based crack filler. 2. Application :- Apply the first coat of Dr. fixit dampguard classic with a paint brush directly on the prepared surfaces by mixing (1 part base : 1 part hardner : 1 part of water), allow to dry for a minimum 2-3 hrs. apply one part of Dampguard mixed chemical and 2 parts of OPC white cement / Birla putty and make the putty, apply putty on the entire surface area, allow to dry for at least 3-4 hrs, apply the final coat of air cure 48 hrs proceeds for paints.

M&L PCC 1:2:4 type B-1, using (20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges including necessary form work etc complete all as specified & directed

M&L PCC 1:7:12 using 40mm graded stone aggregate as filling of sunken floors/bottom and side of drain complete all as specified & directed

Supply only integrated water proofing compound complete all as directed by Engr-in-charge.

M&L for brick work with fly ash bricks straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) all as specified & directed.

M&L for brick work with fly ash bricks straight or curved on plan any radius half brick thick walls, built in cement mortar (1:4) all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each and removing from site all as specified & directed

Taking down existing shutter and refixing in same opening shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each all as specified and directed. (Note:- 'Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.)

S&F framed work as in chowkats of doors windows of angle iron ,gates or other section with gusset plates, rails, braces etc conforming to Gde Fe 410-0 or Fe 310-0 complete (Quality -A) all as specified and directed by Engr-in-Charge.

S&F for Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes, framed guard bars; barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290-0 or grade E- 165 complete all as specified and as directed

Supply & fixing 35mm thick 2nd class hard wood factory made plain framed panelled shutters (Three panels) with lock rail and panel inserts of comercial veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated all as specified & directed

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed.

Taking down chowkats or frames but with shutter without taking off shutter from the frame area n exc 1.5 sqm each but with shutters (without taking off shutters from the frames) and removing from site,complete all as specified and directed.

Taking down shutters of any description exc 1.00 sqm but not 2.00 sqm each including removing to store complete all as specified and directed.

Supply and fixing of Fibre glass Reinforced plastic (FRP) door frame of required built in colour in three legged of cross-section 90mm x 45mm having single ribate of 32mm x 15mm to recieve shutter of 30mm thick including laminated door frame moulded with fire retardant grade unsaturated polyster resin and chopped strand mat(CSM) also door frame laminated shall be 2mm thick and shall be filled with suitable wooden block of 2nd class hard wood in all three legs frame shall be covered with fibreglass from all sides MS stay flat iron 25mm x 3mm shall be provided at the bottom to steady the frame complete all as specified and as directed by Engineer-in- charge.

Supply and fixing of 30 mm thick glass fibre reinforced plastic (FRP) paneled door shutter conferming to IS:14856-2000 of required colour and made with fire retardant grade unsaturated polyster resin,moulded to 3mm thick FRP laminated for forming hollow rails and style with suitable second class hardwood timber block inside at required places for fixing of fittings,cast molithically with 5mm thick FRP laminated for panels including fixing to frames,complete all as specified and as directed by Engineer-in- charge.

S & F hold fast of flat iron conforming to Fe-290 or Fe 330 including preparing the surfaces & treated with two coats for coaltar & sanded with clean sharp sand complete all as specified & directed.

S&F aluminium handles anodised cast type 125 mm long all as specified & directed by Engr-in-charge.

S&F for 100 mm long butt hinges mild sttel with stainless steel hinge pin, anosied and fixed all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 200mm long all as specified & directed by Engr-in-charge.

S&F 100 mm long butt hinges extruded aluminium alloy with galvinised mild steel hinge pin, anodised and fixed type B-21 complete all as specified & directed by Engr-in-charge.

S&F 150mm long aluminium alloy handles, fabricated type, anodised complete all as specified & directed by Engr-in-charge.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt type not less than 16mm dia fixed all as specified & directed by Engr-in- charge.

S&F as 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete all as specified and directed by Engr-in-Charge.

S&F for 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring all as directed.

S&F stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples all as directed.

S&F for powder coated anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing exc 0.55 Kg/m (1.50 to1.80mm th) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings

S & F for Aluminium anodised (Powder coated) Three track sliding window frame with shutters (two glazed and one gauged shutter) including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete and glazing with 5 mm thick tinted glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc with the following section of frame and shutter (A) Sections for frame (i) Top and verticals 92 x 29.50 x 1.30 mm thick (ii) Bottom 92 x 29.50 x 1.20 mm thick. (B) Sections for shutter (i) 'A' section 39 x 20 x 1.50 mm thick (ii) 'Interlock' section 39 x 20 x 1.50 mm thick(iii) 'H' section 41 x 20 x 1.10 mm thick Make: Jindal or equivalent sections of Hindalco.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises all as specified and as directed.

M&L for Non skid coloured ceramic tiles (Joint less) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but n exc 0.18 as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed

M&L glazed ceramic coloured tiles 450 x 300 x 7 mm thick joint less tiles as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed

S & F Virified Ceramic tiles light colour of double charges 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick rendering in CM 1:6 complete all as specified and directed

S & F Virified Ceramic tiles light colour of double 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, on to dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:6 complete all as specified and directed

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc and laided, bedded and pointed in any mortar complete all as specified and directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bedding in cement mortar 1:6, all as specified and directed.

M & L Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed

Taking down cement plaster/terrazoo on brick / stone walls including raking out joints, hacking for key, scrubbing down with water all as directed

M & L for Rendering 15 mm thick on brick work or concrete surfaces in CM 1:6 finished even and smooth on wall and smooth without using extra cement all as specified and directed by Engr-in-charge.

M&L for rendering 15mm thick on brickwork or concrete surfaces in cement mortar 1:4 on wall and finished fair complete all as directed.

M & L for Rendering 10 mm thick on brick work or concrete surfaces in CM 1:4 finished even and smooth on ceiling and smooth without using extra cement all as specified and directed by Engr-in-charge.

M&L for two coats of acrylic distemper on newly plastered surfaces of walls paint over 3mm thick wall care putty including preparation of surfaces complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing treatment and two coats of acrylic distemper over 3 mm thick wall care putty on plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L preparing newly plastered or pointed surface of ceiling and applying three coats of white wash on ceiling complete all as specified & directed by Engr-in-charge

M&L for preparation of old plastered or pointed surfaces by complete removal of exiting treatment of wall and applying two coats of white wash complete on ceiling all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered and treating with two coats of weather proof exterior emulsion paint (Apex ultima or equivalent) over a coat of alkali resistant primer over 3mm thick wall care putty complete all as specified and directed by Engineer-in-charge.

M&L for preparation of old plastered and treating with two coats of weather proof exterior emulsion paint (Apex ultima or equivalent) over a coat of alkali resistant primer over 3mm thick wall care putty complete all as specified and directed by Engineer-in-charge.

M & L for painting steel and iron surfaces of any discription,over 10 cm width or girth, including preparation of new surfaces applying with two coats of synthetic enamel paint over coat of red oxide primer ordinary tint all as spefified and directed

M & L for painting steel and iron surfaces of any discription,over 10 cm width or girth, including preparation of previously untreated surfaces and one coat of red oxide and finish with two coats of synthetic enamel paint ordinary tint all as spefified and directed

M&L preparation of new or wooden based surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer all as specified.

M&L for preparation of old or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply one coats of synthetic enamel paint all as specified.

S & F 4 mm thick pin head glass and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or any pattern), including all fitting, such as heads, shoes ,bends swan-necks etc, including cleaning or refixing or removal to store etc. complete all as specified and directed by Engr-in -Charge.

S&Fin repair 110 mm dia bore UPVC pipe, single socketed in any length with rubber ring joints fixed with clamps to walls and including bend as per side requirement, taking down existing pipe all as directed.

S & F in repair 450 mm long mild steel GI pipe, medium grade of size 40 mm dia as in spouts pipe in sunken floor including making holes in RCC and making good with CM 1:1 or PCC (1:2:4) complete all as specified and directed by Engineer-in-Charge

S & F PVC bend 110 mm bore all as specified & directed by Engr-in - charge

Dismantling of cast iron pipes, jointed in cement mortar and taking out of trenches/wall if required upto 100mm dia complete all as specified and as directed by engineer-in-Charge.

S & F 100 bore of spun cast, cast iron soil, waste and vent pipes in any length with or without ears, with cement joint and laid in trenches or in floors cast iron complete all as specified and directed.

S & F in repair cast iron 100 mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S & F in repair cast iron 100 mm bore Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S & F in repair 75mm bore of spun cast iron soil, waste and vent pipes in any length with or without ears, with cement joint and fixed to wall complete all as specified and directed.

S & F in repairs 75 mm cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1, (1:2:4) complete all as specified and directed by Engineer-in-Charge.

S & F in repair 75 mm bore of cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches and Oval access door complete all as specified and directed

S & F in repair cast iron 75 mm bore Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

Taking down 15 mm dia steel tubing including all connected fittings of any dia and in any position including cleaning for re fixing the serviceable pipe all as directed.

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as directed.

Taking down steel tubing and connection including cleaning for refixing or removing to store bore of pipe 20 mm complete all as specified and directed by engr-in-charge.

S&F 20 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as directed.

Taking down steel tubing and connection including cleaning for refixing or removing to store bore of pipe 25 mm complete all as specified and directed by engr-in-charge.

S&F 25 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as directed.

S&F in repair bib tap 15mm bore cast copper alloy chromium plated long body fancy type with capston head and cup screwed down, hand operated, screwed for iron pipe or for brass ferrule all as specified.

S&F in repair CP brass stop/angle valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup fixed all as specified.

S&F in repair CP brass stop valve fancy type 15 mm bore cast copper alloy screwed down high pressure fancy type with long shank and cup (Concealed type) fixed complete all as specified and directed by Engr-in-charge.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 25 mm bore fixed in repair all as specified and as approved by GE/Engineer-in-Charge.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed in repair all as specified and as approved by GE/Engineer-in-Charge.

M & L for 19 mm thick playwood in repair, gradeBWR, type BB, with decorative face veneers on both faces; handle and fixed with screws to timber frame work complete all as specified and directed

S & F continuous (Piano) hinges mild steel bright finsh or electro galvanised, width of flap when open 30mm complete all as specified and directed by Engr-in-charge.

S&F in repairs for stainless steel rods, standarad quality, not less than 28mm dia with heads, brackets and boths ends stainless caps , etc. all as specified and direced.

S & F in repair cabinet mirror of size 400mm X 500 mm fixed with wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-Charge

S&F in repair tubular towel rail stainless steel 20mm dia 'D' type 60cm long between flanges complete all as spd & dir by EIC.

Supply and fixing in repair glass corner shelf with CP brackets and CP railingcomplete all as specified and directed by Engineer-in-Charge.

S&F in repair chromium plated fancy type soap dish complete all as specified and directed

S&F repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with integral foot rests (excl flushing cistern) but including CI 'P' trap set in and including concrete fixed all as specified.

S&Fin repair vitreous china wash down water closet pan (pedestral pattern), white (excluding fixing bolts ,flushing cistern and flush pipe), including pedestal pan and trap,including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etccomplete.

S & F in repair Vitreous china urinal flat back of size 465X355X265 mm white with grating & Union for discharge pipe including spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60 grms) but including flushing cistern, flush pipe & waste pipe but fixing only automatic flushing cistern with bracket flush pipe etc .

S&F in repair vitreous china wash hand basin coloured counter top (bowl type/oval shape) of size 560x450mm, long screwed shank fly nut flange end including cutting for and pinning in ends of brackets in 1:3 CM including 32mm dia chromium plated waste coupling/trap all as specified .

S&F in repairs grating doom CP 100 mm dia of plated with waste hole complete all as specified and directed

S & F in repairs 32 mm PVC waste down pipe suitable for WHB and urinal complete all as specified and directed by Engineer-in-charge

S & F in repairs pillar tap, fancy type, cast copper alloy chromium plated with capston head, screwed down high pressure with or without lettered with long screwed shank and fly nuts, screwed for iron pipe of 15 mm bore complete all as specified and directed. (Wt not less than 450 gms)

S&F in repairs PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern all as directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm long.

Supply & fixing in repairs Chromium plated (CP) swivel shower roses 125mm with or without swivel joints, including fixing to steel pipe or union fixed complete all as specified and directed by Engr-in-Charge.

Dismantling exc 250 but n. exc. 500 litre capacity any type of water tank and remove from site complete all as specified and directed by Engineer-in-Charge.

Dismantling exc 500 but n. exc. 1000 litre capacity any type of water tank and remove from site complete all as specified and directed by Engineer-in-Charge.

S&F for Rotational moulded polythene water storage tank 500 ltr capacity vertical with closed top hoisted and fixed in position all as specified in SSR part-I. All as directed and including 20 mm bore PTMT float valve and connection nipple as required basis complete all as specified and directed by Engineer-in-Charge. .

S&F 1000 litre capacity ISI marked rotational moulded tripple layer polyethylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (minimum weight 15mm-142 gms/20mm-210 gms/25mm-455gms)

S&F for TMT bars (Fe-500D) 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

,--ditto--- all as per Serial item No 109 above, but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders all as specified and directed

Demolition of cement concrete in ground floor and paving n.exc 15cm in thickness (below or above ground level) all as specified.

M&L for 75 mm thick cement concrete type B-2 (1:3:6) using 40 mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as directed.

M&L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in sub base below floors all specified and directed.

M&L for precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in kerb stones of size 300 mm x 300 mm x 100 mm with plain fair faces, including chamfers, weathering, throating etc setting in CM 1:4 complete all as specified and directed.

M&L Machined pressed precast concrete interlocking paver block glossy with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with over Fazilka sand cushion all as specified and directed. (Sand will be measured and paid seperatly)

Suply only 25 mm thick Fine aggregate (sand) for Cushioning (Fazilka sand) all as specified and directed

M&L for PCC 1:2:4 type B1 using 20mm graded aggregates as in benching / haunchig of manholes including forming channels including necessary formwork etc.

M&L for PCC 1:2:4 type B1 using 20mm graded aggregates as in coping and the like including weathering slightly rounded or chamfered angles and throating, as directed including necessary formwork etc.

M&L precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate and set cement mortar 1:6 as in cover slabs (for manholes etc), chajjas, shelves and similar articles with plain faces all as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

E/M Portion Taking down carefully unserviceable point wiring (light, socket or power and bell) complete including (fittings such as switches, ceiling roses, pendants, regulators, sockets), and making good disturbed surfaces of walls, floors etc to match with existing surfaces.

Taking down unserviceable MCB with sheet metal enclosure, main switch, DB etc and making good disturbed surfaces to match with existing surfaces.

Taking down unserviceable sub main wiring of any size/capacity complete all as specified and making good disturbed surfaces to match with the existing surfaces

M&L for concealed Point wiring with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with modular sheet top cover of required module for mounting switches, sockets etc one light point controlled by one, one way swith complete all as specified and directed by Engr-in-Charge. complete all as specified. Note - quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour for One Light point controlled by one, one way switch complete all as specified and directed by Engr-in-Charge. .

,--ditto--- all as per Serial item No 124 above, but for One ceiling/exhaust fan point controlled by one switch and regulator complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 124 above, but for One bell/buzzer point controlled by one bell puch complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 124 above, but for One 3 pin 5 amps switch socket outlet point on same board with other switches complete all as specified and directed by Engr-in-Charge.

,--ditto--- all as per Serial item No 124 above, but for One 3 pin 5 amps switch socket outlet point on independent board complete all as specified and directed by Engr-in-Charge.

,---ditto-- all as per item No. 124 above but point wiring with 4 sqmm multi stranded conductor cable and 2.5 sqmm unsheathed copper conductor earth wire for two in one 5 pin 15 Amp socket outlet on indep board.

Supply and fix Modular switch 1 Way 6A, 1 Module, 230 Volts grade all as specified and directed by Engr-in-Charge

Supply and fix Modular Socket 1 Way 6 A-2/3 pin combine 2 Module, 230 volts grade all as specified and as directed by Engineer-in - Charge

Supply and fix Modular Socket 6A/16A-2/3 pin combined 2 module all as specified and as directed

Supply and fix 1 way 16 Amp 1 Module all as specified and directed Engineer-in-Charge

S & F LED light fitting 1 x 20 W, 230 V integral sleek polycarbonate LED Channel with white acrylic cover incl making connection complete.

Supply & fix Modular Bell push switch 6A, 1 Module all as specified & directed by Engineer-in- charge.

Supply & fixing bell AC 230 volt single pole all as specified & directed by Engineer-in- charge.

Supply and fix ceiling rose surface bakelite two to three terminals/plate 5 amps complete all as specified and directed by Engr-in-Charge.

Supply and fix Modular fan regulator, 120 W-2 module with step suitable for 1200/1400mm sweep ceiling fan working on 230 volt AC complete all as specified and directed

Supply and fix in replacement Vertical MCB DB distribution box 3 phase TPN for 415 Volts 08 ways double door with bus bar rating 200 Amps vertical type dust and vermin proof complete all as specified and as directed.

Supply and fix sheet metal enclosure DB single pole and neutral for 240 volts 4 way with 200 Amps rated busbar flush/surface mounting double door complete all as specified and directed

Supply and fix MCB SP 240 volt 5-32 amp 10KA complete all as specified and as directed.

Supply and fix MCB SP&N 240 volt 5-32 amp 10KA complete all as specified and as directed.

Supply and fix MCB SP 240 volt 40 amp 10KA complete all as specified and as directed.

Supply and fixing PVC Blanking Plates one way with internal lock complete all as specified and as directed.

Material & Labour for Sub Main Wiring with two run single core 6 Sqmm PVC insulated unsheathed (FRLS) cable with stranded copper conductor drawn in PVC conduit & accessories Suitable size with and including 4 Sqmm copper green colour earth wire all as specified and directed by Engineer-in-Charge. NOTE-two run of 6 sq.mm & One run of 4 sq.mm & One run of PVC conduit with accessories shall be measured as One length.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth of not less than 1.5 metre below ground level, earth plate surrounded by 15cm thick and packed layer of charcoal dust and common salt, connected to earth lead of GI wire 4 mm dia (8 SWG) by means of bolts, nuts and washers of the earth wire.galvanised iron or steel and thimbles and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 15mm dia and water pipe 20mm dia GI light grade with funnel and wire mesh, PCC chamber in cement concrete (1:2:4) type B-1 and CI cover with frame all as shown in electrical plate No. 3 of MES Schedule Part-I of SSR-2009. Notes :- (i) 20 mm dia GI pipe for watering to be provided with a socket and plug and should be 10 cms above ground level. (ii) Outer edge of earth pit will be 1 metre away from the outer edge of PCC chamber. (ii) GI wire upto DBs earth connection is included in this item. (iii) Water pipe shall be provided in slanting position

Supply and fix sheet metal incl single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 240 Volts Complete all as specified and directed by Engr-In-Charge

S & F Mirror light 10 watt, insulated body with back plate etc all as specified and directed by Engineer-in- Charge

S & F fresh air fan 200 mm sweep, single phase 230v 50 Hz including grouting with fasteners, nuts/bolts etc complete all as specified and directed by Engineer-in-charge

S & F LED buildign security light fitting 25 watt with epoxy powder coated sheet aluminium housing, with epoxy powder coated CRCA sheet steel gray tray, clear acrylic cover and accessories complete incl street light bracket made out of 25 mm dia GI medium grade pipe 0.6 mtr long complete with 02 seats of FI clamps made out of 30 x 5 MS flat & nuts, bolts & washer including painting to clamp with two coats of aluminum silver paint over a coat of primer after taking down old U/S one complete all as specified and directed by Engineer-in-charge

Supply and lay, jointing and testing of cable 1100 volt grade 50 Sqmm 3.5 core with standred aluminum conductor PVC sheathed armoured confirming to IS156 laid in trenches/along poles/through pipe/through duct completed all as specified and directed by Engineer-in - Charge

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

SHIVA CONSTRUCTION COMPANY

ram rattan dass aggarwal

M/S Shree Ram Enterprises

PAREEK AND COMPANY

Akarsha Enterprises

GOYAL ENTERPRISES

AJAY CONSTRUCTION COMPANY

M/s Karan Builders

KHANNA CONSTRUCTIONS

Aggarwal brothers and company