Making Lighting, Fire Fighting arrangement, installation of CCTV Camera, Sump House for Retain and discharge of Rain water from Tunnel at Panki Power House, Kesco., Kanpur.

Supply of 10 HP water lifting pump as per relevant IS from reputed manufacturer.

Supply of Starter with auto sensor System for 10 HP Water lifting pump as per relevant IS from reputed manufacturer.

Supply of L.T. Pannel having 01 No. incoming MCCB of 250 Amp and 08 No. outgoing MCCB 63 Amp. as per relevant IS from reputed manufacturer.

Supply of L.T. XLPE Cable 3½x150 mm2 as per relevant IS from reputed manufacturer.

Supply of L.T. Alu. Lug 150 mm2.

Supply of brass Cable gland 150 mm at L.T. panel end.

Supply of L.T. XLPE Cable 3½x70 mm2 as per relevant IS from reputed manufacturer.

Supply of L.T. Alu. Lug 70 mm2.

Supply of brass Cable gland 70 mm at L.T. panel end.

Supply of L.T. XLPE Cable 4x16 mm2 as per relevant IS from reputed manufacturer.

Supply of L.T. Alu. Lug 16 mm2.

Supply of ceiling light size 300x300 mm 40 watt as per relevant IS from reputed manufacturer.

Supply of PVC pipe 65 mm dia 1.0 mm thick.

Supply of 01 Set Automatic fire suppression system Comprising of the following.

45 kg Co2 Cylinder with Master Valve

45 kg Co2 Cylinder with Slave Valve

Discharge Hose ½"

Interconnecting Hose

Cylinder Battery Frame with Manifold

Safety relief Valve

Bleeder Valve

Pressure Switch

Nozzle

Detection System including panel, Detector, MCP, Hooter, Switch and Manual releasing Switch with caballing

Piping Job

Supply of Fire Fighting equipment of 5 kg capacity ABC type with auto operating sensor.

Supply of CCTV IP Camera along with DVR Rack, LED Screen, modem etc.

Supply of S.T. Pole (SP-55) 11.00 Mtr. long.

Supply of M.S. Channel 100x50x6 mm 2.4 Mtr. long.

Supply of M.S. Clamp 5½" 50x6 mm.

Supply of M.S. Earth Rod Complete with earth wire 20 mm. dia 2540 mm long.

Supply of M.S. Angle 65x65x6 mm 3 Mtr. long.

Supply of Bracing Clamp 6½" dia 50x6 mm.

Supply of Bracing Clamp 7½" dia 50x6 mm.

Supply of Barbed Wire 12 SWG

Installation of 10 HP water lifting pump after making suitable plinth as per Standard Specification.

Installation of Starter with auto sensor System for 10 HP Water lefting pump at after making suitable structure.

Installation of L.T. Panel having 01 No. incoming MCCB of 250 Amp and 08 No. outgoing MCCB 63 Amp.

Laying of L.T. XLPE Cable 3½x150 mm2 from existing L.T. main to L.T. panel.

Fixing of L.T. Alu. Lug 150 mm2 on Cable Ends.

Fixing of brass Cable gland 150 mm at L.T. panel end.

Laying of L.T. XLPE Cable 3½x70 mm2 from L.T. panel to water lifting pump.

Fixing of L.T. Alu. Lug 70 mm2 at Cable Ends.

Fixing of brass Cable gland 70 mm at L.T. panel end.

Laying of L.T. XLPE Cable 4x16 mm2 from L.T. Panel to tunnel lighting.

Fixing of L.T. Alu. Lug 16 mm2at Cable Ends.

Installation of ceiling light size 300x300 mm 40 watt at ceiling of tunnel.

Laying of PVC pipe 65 mm dia 1.0 mm thick.

Installation of 01 Set Automatic fire suppression system Comprising of the following.:- 45 kg Co2 Cylinder with Master Valve (02 No.), 45 kg Co2 Cylinder with Slave Valve (16 No.), Discharge Hose ½" (18 No.), NRV ½" (18 No.),Interconnecting Hose (17 No.), Cylinder Battery Frame with Manifold (18 No.), Safety relief Valve (01 No.), Bleeder Valve (01 No.), Pressure Switch (01 No.), Nozzle (29 No.),Detection System including panel, Detector, MCP, Hooter, Switch and Manual releasing Switch with caballing (01 Job) , Piping Job (01 Job)

Installation of Fire Fighting equipment of 5 kg capacity ABC type with auto operating sensor at different locations of tunnel on suitable Stand.

Fixing of 06 No. CCTV IP Camera alongwith DVR Rack, LED Screen, modem etc. near by newly constructed tunnel.

Making arrangement for Wi-Fi Connection for 3 years and installation of the same at tunnel end and monitoring end.

Erection of double pole along with all accessories with grouting, making plinth and painting as per standard Specification.

Erection of barbed wire, fencing along the boundry of 220/132/33 KV Panki S/S where it is damaged.

Welding of trench cover outside PTPS boundary wall to avoid theft of trench cover.

Painting of 08 No. Racks of tunnel 75 Mtr. long to 1 Mtr. wide.

Excavation in foundation in ordinary soil (loam clay or sand) including lift upto 1.5 Metre and lead upto 30 metre and including filling, watering, and ramming of excavated earth into the trenches or into the space between the building and the side of the foundation. (CSI 4.01 )

Concrete with 4 cm gauge down graded stone ballast coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 8:4:1 in foundation and under floors including supply of all materials, labour and T & P etc. required for proper completion of the work (CSI 5.02)

Cement concrete with 2cm gauge Stone ballast, coarse sand and cement in the proportion 3:1.5:1 including supply of all materials, labour and T&P etc. required for proper completion of work. (CSI 5.04)

RCC work with cement, approved coarse sand and 2cm (3/4”) gauge approved stone ballast in the proportion of 1:1.5:3 in the lintels or bends and sun shade of doors and windows excluding supply of reinforcement and its bending but including its cutting, fixing and binding the same with 24 B.W.G. G.I. wire including necessary centering and smooth shuttering etc. required for proper completion of work including supply of all material, binding wire, labour and T&P etc. (CSI 5.08).

RCC work with cement, approved coarse sand and 2cm (3/4”) gauge approved stone ballast in the proportion of 1:1.5:3 in the slab excluding supply of reinforcement and its bending but including its cutting, fixing and binding the same with 24 B.W.G. G.I. wire including necessary centering and smooth shuttering etc. required for proper completion of work including supply of all material, binding wire, labour and T&P etc. (CSI 5.10)

RCC work with cement, approved coarse sand and 2cm (3/4”) gauge approved stone ballast in the proportion of 1:1.5:3 in Raft/Footing excluding supply of reinforcement and its bending but including its cutting, fixing and binding the same with 24 B.W.G. G.I. wire including necessary centering and smooth shuttering etc. required for proper completion of work including supply of all material, binding wire, labour and T&P etc. (CSI 5.14)

RCC work with cement, approved coarse sand and 2cm (3/4”) gauge approved stone ballast in the proportion of 1:1.5:3 in the T-beam columns and wall upto 1.5mtr. height only web of T or L beam shall be measured excluding supply of reinforcement and its bending but including its cutting, fixing and binding the same with 24 B.W.G. G.I. wire including necessary centering and smooth shuttering etc required for proper completion of work including supply of all material, binding wire, labour and T&P etc. (CSI 5.16)

1st class brick work in 1:4 cement and coarse sand of 2.25 F.M. mortar in foundation and plinth including supply of all material, labour and T&P etc. required for proper completion of work. (CSI 6.02)

1st class brick work in 1:4 cement and coarse sand of 2.25 F.M. mortar in super structure for wall of one brick (230mm) thick. (CSI 6.02+6.06)

Mild steel or iron work in heavy large size sections such as trusses, built-up gates, roof work, window/boundary grill or railing, trench covers, grating, T/F rail etc. wrought to required form including supply of steel bolts, nuts, wastage etc. and their fixing charges, welding, required for proper completion of the work. (CSI 9.02)

Mild steel or iron in plain work such as reinforced concrete or reinforced brick work (when not included in over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage, bend, hooks, and authorized overlapping as required for proper completion of the work. (CSI 9.04)

Supply and fixing welded wire mesh size 75x25mm and rectangular made out of 10 SWG over M.S. angle frame with M.S. flat with nut and bolt welded as required including cost of drilling holes, bolts, nuts, washer wilding etc. as required including cost of all material, labour and T&P etc. required for proper completion of work . except cost of Angle iron flat. (CSI 9.37)

Providing and fixing percolated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm ( + 0.05 %), total coated thickness with zinc coating 120 gm per sqm as per IS:277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (DSR 12.5)

12mm thick plaster with cement mortar of 1 part cement & 4 parts of approved coarse sand 2.5 F.M. over Brick work, min. thickness not less than 10mm including supply all material, labour and T&P required for proper completion of work. (CSI 11.05)

Local Fine sand of 1.25 F.M. filling in plinth including supply of necessary quantity of sand from a river/canal nearest to the site of work including watering, ramming and dressing etc. Rate to include cost of all materials, labour and T&P etc. required for proper completion of work. (CSI 4.08)

40mm thick 1:2:4 cement concrete floor with cement, approved coarse sand and 20mm graded stone aggregate laid in panels finished with 3mm floating coat of neat cement, over base concrete. Rate includes cost of all materials, labour and T&P required for proper completion of work but excluding cost of base concrete.. (CSI 12.02)

Providing and fixing glass strip of 3.15 mm (1/8”) thick and 3.5cm. deep in joints of floor at the time of laying floors flush with floor level including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI 12.09)

Painting or varnishing on iron works in small areas of new wood work with one coat of ready mixed priming paint and two coat of approved superior quality ready mixed paint of clear synthetic varnish including supply of all materials, labour and T&P etc. required for proper completion of the work. Paint to be used should confirm to the ISI no. 103-1950. (CSI 13.01+13.02 )

Applying BIRLA PUTTY or equivalent putty on new interior or exterior surface over one coat of water base cement primer of ICI or equivalent brand for smoothing and leveling of the surface as per requirement and direction of E/I, including cost of all material, labour and T&P required for proper completion of work. (CSI 13.04).

Finishing walls with water proof exterior emulsion paint of APEX ULTIMA (ASIAN)/Weather Shield Max (ICI) or equivalent brand on already well prepared new wall surfaces over one coat of under coat primer (ICI) followed by Two coat at Apex/Weather shield Max emulsion paint to give an even shade including thorough washing with water as per direction E/I including cost of all material labour & T&P required for proper completion of work. (CSI 13.06)

One priming coat & two coat synthetic/acrylic distemper on new work including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI 13.09+13.10)

Providing and installation of 80 mm dia outlet size KSB / KIRLOSKER / HINDUSTAN or equivalent make submersible pump set of 7.50 H.P. suitable for 150mm dia bored tube well having discharge of2400 L.P.M. at a total head of 57/46 metres. complete in all respect consisting of four stage pump set fitted with special stream lined non return valve, directly coupled to squirrel cage induction motor of 7.5 H.P. 400/440 volts 3 phase A.C. 50 cycle, 2900 rpm suitable for star Delta starting including making electric connection to the control panel, testing and commissioning of the pumping set, including binding of supporting guide with the help of steel wire rope 5mm dia including its cost required and S/F of complete inbuilt set of control penal prescribed by manufacturer of pump for proper completion of the work. (CSI 18.31)

Providing and laying of 5.90mm thick, 200 mm. dia M.S. Housing pipe of ‘TATA/JINDAL’ or equivalent make (as approved sample by E/I) cost of all materials, labour and T&P etc. required for proper completion of work. (CSI 18.49)

Providing and fixing of supporting clamps for 80/50 mm dia pipes including cutting the pipe of required length and welding the same including cost of all materials, labour, T&P etc required for proper completion of work. (CSI 18.24)

Providing and lowering of 80 mm dia. G.I. ‘B’ class column pipe TT/Swastik make with column coupling socket etc. including cutting the pipe of required length and welding the same including cost of all materials, labour, T&P etc required for proper completion of work. (CSI 18.25).

S/F hexagonal fan box with hexagonal side approx. 80mm in length fabricated 16 SWG MS sheet incorporation 10mm dia MS round bar duly bent for supporting fan hanger duly painted with red oxide and screwing arrangement with wiring conduit laid in the RCC roof before concreting along with supply of all material labour T&P etc. required for proper completion of work. (CSI 21.22).

Wiring point for light with 1.5 sq. mm. FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit concealed in wall with 1.5 sq. mm. FRLSH PVC insulated multistrand copper conductor cable as earth wire drawn inside the conduit GP Box, piano type switch and ceiling rose/angle/ batten holder on 3 mm. thick phenolic laminated backelite sheet etc. complete in all respect as per direction of E/I. (PWD 121-C)

Wiring point for fan /fresh air fan (light duty exhaust fan) with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit Concealed in wall with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earth wire drawn inside the conduit piano type switch and ceiling rose/angle/ batten holder on 3 mm. thick phenolic laminated backelite sheet etc. complete in all respect as per direction of E/I. (PWD 133-C)

Wiring point for plug with 1 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit Concealed in wall with 1.5 sq. mm. FRLSH PVC insulated multistrand copper conductor cable as earth wire drawn inside the conduit piano type switch and ceiling rose/angle/ batten holder on 3 mm. thick phenolic laminated backelite sheet etc. complete in all respect as per direction of E/I. (PWD 134-C)

Supply and fixing of power plug with 15A/250 volt flush type switch and 5 pin 15A/250V flush type universal socket in suitable M.S. box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer. (PWD 1139)

S&F of 6 Amp to 32 Amp. MCB (10 KA) C Curve. (PWD 1002-B)

Supply & fixing of LED Tube light fitting 18watt -4Ft. of Crompton or equivalent make including labour T&P etc. (NSI)

Supply & fixing ceiling fan of high speed 48” of Crompton or equivalent make including labour & TP etc. (NSI)

S/R of regulator for ceiling fan of GEC or equivalent make including cost of all labour material, T&P etc. required for proper completion of the work. (CSI 22.60b)

Supply and fixing of LED street light fitting having dia cast aluminum body and diffuser with driver set suitable for 110 to 130 Watt. Confirming to IP 66 production complete in all respect. (PWD C.S.I. No. 1424, CAT-AA)

Annual maintenance for three years for fire fighting system, CCTV Camera, Sum Pump and all accessories supplied by contractor.

Khan Traders and Electrical Works