SPECIAL REPAIR WORKS OT BLDG NO TR01 AT MH DANAPUR ADDN ALTN OF TOILET BLOCK P63B AND ADDN ALTN OF TOILET BLOCK IN STATION HQ CELL DANAPUR UNDER GE DANAPUR CANTT

Amount

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based semi corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mps as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by E-in-Charge

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide primer complete.

Demolition of brick work built in cement mortar including all quoins, arches, pillars, complete all as specified and directed

M & L for Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and as directed.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes finished even and rough complete all as specified and directed.

M&L for PCC type C2, 1:3:6 (40 mm graded stone aggregate) as in foundation filling and mass concrete for manholes, septic tanks & drains and for smiliar work complete all as spd and as directed

M&L for plain Cement concrete 1:2:4 Type B1 using 20 mm graded aggregate as in roof curb r mud stops, coping benching and surface channel/padding and for similar work including necessary formwork complete all as specified and directed.

M&L precast RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in man hole cover slabs and set in CM (1:4) complete all as specified and directed by Engr-in-Charge.

M&L for MS TMT bar 5mm dia & over up to 10mm dia for distribution bar,stirrups, spacer etc ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.90mm dia or securing with clips complete all as specified and directed.

M&L for MS TMT bar 10 dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.90mm dia or securing with clips complete all as specified and directed.

M & L for Hardcore of gauge exc. 63 mm but not exc. 100 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken bricks complete all as specified and directed.

M&L for 10 mm thick plaster in cement mortar 1 : 4 as a backing coat for fixing of wall tiles complete all as specified.

M & L for 450x300 x7 mm to 350x275x7 mm thick glazed ceramic tiles (Digital pattern) including highlighter colored as in dado/ skirting and vertical serfaces set&jointed in neat cement slurry and pointed in colored cement over and incl 10 mm thick cement mortar 1:4 to match the Shade, pattern, laying etc of tiles complete all as specified and directed.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes finished even and rough complete all as specified and directed.

M & L for Non skid ceramic colour tiles (square / rectangular) of 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exc. 0.18sqm as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed (1:6) etc complete all as specified and directed.

M&L for anodised aluminium snap grid frame work with supporting hangers comprising of GI wire 4 mm dia with J hook, nuts/bolts etc for false ceiling with size of grid 605 x 605 mm consisting of main and cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg per RM and wall angle 23.5 x 26.4 x 1.4 mm weighing 0.191 Kg per RM respectively complete all as specified and directed. Make : Armstrong, Hunterdouglas

M&L for 6 mm thick E-board of size 600 x 600mm fixed to aluminium snap grid frame work as in ceiling flat or sloping conforming to IS -14862 complete all as specified & directed. Make : Armstrong, Hunterdouglas

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillet complete all as specified and directed.

M&L for cutting holes in brick wall built in cement mortar for inserting holdfast , walls exc half brick n.exc one brick thick and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate complete all as specified and directed.

M & L Rendring 15mm thick in cement mortar 1:6 on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete all as specified and directed. Note:- Liquid WPC will be measured and paid separately.

Supply only water proofing compound (liquid), ISI marked.

M&L two coats of cement base paint over a coat primer on wall including preparation of newly plastered surfaces.

M&L for two coats of Apex weather proof paint on newly plastered surfaces over a coat of primer including preparation of surface complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of newly plastered surfaces and applying two coats of oil bound distemper over a coat of primer including 3 mm thick Birla/ JK wall putty complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete all as specified and directed

Boring holes 3m deep and 300 mm dia of pile in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50 m complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance exc. 50 m but not exc. 25 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for 100mm thick plain cement concrete, 1:4:8 type D-2 Nominal Mix (using 40 mm graded stone aggregate) as in sub base finished even & fair etc complete all as specified and directed..

M & L for sand filling under floors or in foundations including watering and consolidation as required complete all as specified and directed.

M & L for plain cement concrete, 1:4:8 type D-2 Nominal Mix (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed..

M&L Cement concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in foundation, filling, mass concrete etc complete

M&L for 40 mm thick Damp proof cource in cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate to horizontal or vertical surface incl necessary form work concrete complete all as specified and directed. .

M&L reinforced cement concrete (M-25 Nominal mix) (using 20 mm graded stone aggregate) in foundation, footing, foundation beams, plinth beams, bases for columns, pedestal, under reamed piles, mass concrete, etc complete.

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&Lfor providing reinforced cement concrete M-25 Design Mix using 20mm graded aggregate as in beams, cantilevers, bressmummers, lintels over 1.5 m span complete all as directed

M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

All as per item No 46 above but 5 mm dia and over in stirrups, spacers and binders complete.

M & L for Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M & L Rendring 15mm thick in cement mortar 1:6 on fair faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

S&F in repair 500 Ltrs capacity rotational moulded polythene water storage tanks in three layer cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed

S&F in repair 15 mm dia nipple suitable for HDPE water tank (min weight 38 gms) complete all as specified and directed

S&F in repair 20 mm dia nipple suitable for HDPE water tank (min weight 45gms) complete all as specified and directed

S&F in repair 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high desity plastic ball srewed for iron pipe and fixed (minium weight 15mm-142gms) complete all as specified and directed

S&F in repair Gun-metal, globe or gate valves 15mm, with iron wheel head, screwed both ends for iron pipe etc complete all as specified and directed .

S&F in repair Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed .

Supply & fixing in repair vitreous china wash basin, light colour Oval shape as fitted on slab or flat back size 550x400mm excluding tap, waste, chain etc. Make: Hindware/Parryware (Superfine)/Cera (Ist quality)/Jaquar

S&F PVC (SWR) 75 mm bore floor trap/Nahani with grating including jointing with solvent cement complete all as specified. Make : Finolex/Supreme

S&F 15mm bore pillar tap cast copper alloy fency type with capastan head chromium plated screwed down high pressure with or without lettered “HOT or “COLD” with long screwed shanks and fly nuts, screwed for iron pipe.

S & F bib tap 15mm chromium plated with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc complete all as specified and directed by the Engineer-in-Charge.

S&F 15 mm bore concealed type stop valves, cast copper alloy, screwed down, high pressure, with capstan head, fancy type, chromium plated, with long shank and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs PVC connection 15mm dia size and 600 mm long with 2 Nos brass check nuts its washers complete all as specified and as directed. Make - Prayag/Jaquar/Cera

S&F in repair towel rail 600 mm long brass CP fixed with and including chromium plated brass screwed and wooden/plastic cleats all as specified

S&F in repair grating doom 125 mm dia with waste hole of chromium plated.

S&F 15 mm bore GI Tubing medium grade including GI fittings fixed to walls, ceilings or laying in floors complete comp all as spd and directed

S&F 20 mm bore GI Tubing medium grade including GI fitting fixed to walls, ceilings or laying in floors including all fittings complete comp all as spd and directed

S&F powder coating aluminium frame for door, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified. Make : Jindal/Hindalco

S&F glass shelf wall corner size 230 mm with all fittings/brackets complete all as specified and as directed by Engineer-in-Charge. Make : Jaquar/Cera

S & F 3 mm thick frosted glass pin head type and glazing with oil putty in squares exc 0.5 Sqm in each pane etc complete all as spd and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples etc complete all as specified and as directed by Engr-in-Charge.

S&F for Pressed steel frame for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc of size 125X60 mm made out of 1.25mm thick MS sheet , complete all as specified and directed.

S&F 35 mm thick plain framed panelled factory made shutter,made out of IInd class hard wood(Bijsal) rail and styles and panel of 12 mm thick veneered particle board or 9 mm thick plywood with commercial veneering on both faces the size of rail and style as per IS 1003 (part-I) kiln seasoned and chemically pressure treated of any number of panel

S & F of 35 mm thick (Batten thickness) 1st class hardwood (SHISHAM) glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified of MES schedule part – I (Specifications - 2009) complete all as specified and directed.

S&F Mild Steel framed guard bars with mild steel Square bars with ends of bars shouldered and riveted and similar work confirming to Fe -290 (Gde E-165)

S & F 100 mm size Butt hinges extruded brass with mild steel hinge pin bright polish and fixed type B-11 complete all as specified and directed.

S & F 150 mm long Aluminium anodised barrel tower bolts of extruded section.

S & F 125 mm long Aluminium handles of extruded section, fabricated type and fixed

S&F aluminum alloy anodised sliding door bolts with hasp & staple & fixing clips of sheet cast extruded section & fixing bolts & sliding bolts of extruded section 250 mm long complete all as specified and directed.

S & F 100 mm size Butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed.

Solid PVC door frame of size 50mm x47mm made out of 5mm plain clour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. Make : Raj shree or Equivalent

M&L for cutting holes in brick wall built in cement mortar for inserting holdfast , walls exc half brick n.exc one brick thick and making good dismantled portion in cement mortar 1:3 complete all as specified and directed.

M & L for 60 mm thick Machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658-2006, M-35 grade as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

S & F steel windows with side hung shutter incl box type butt hinges with bow handle,steel peg stay, tower bolts ( each shutter having two tower bolts 100mm long ) complete (with glazing bars) dovetailed or welded complete all as specified and as directed.

M&L preparation of new wooden surface any description over 10 cm width or girth and applying two coat synthetic enamel paint over a coat pink primer complete all as specified and directed .

S & F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks etc complete all as specified and directed.

Supplying and laying of CPVC pipes 15-16mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

All as per item No 86 above but 32 mm dia pipe.

S&F in repairs, vitreous china squatting pan Orissa pattern size 580mmx440mm white with integral foot rests (exluding flushing cistern and flush pipe) including lime /cement concrete bedding all as specified and directed by Engineer-in-Charge. Make Parryware(Superfine), Cera (Ist Quality), Jaquar/Essess

S&F in repair 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe fixed to wall , complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors complete

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joint fixed to wall complete

S&F clamp made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 110mm PVC pipe complete all as specified and directed.

M&L PVC(SWR) Tee of 110mm dia complete all as specified and directed

S&F PVC (SWR) vent cowl 110mm bore complete all as specified and directed complete all as specified and directed

M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan exc 6m mean radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

S&F in repair of stainless steel soap dish, of standard size and shape complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified and directed.

All as per above item No 98.00 but exc 1.5 Sqm but n.exc. 4 Sqm each.

S & F powder coated aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing handles 2 Nos in each door, hinges, powder coated aluminium snap beading, screws, including eatching work etc. including making good the surface complete all as specified

S&F powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws etc complete all as specified and as directed. (Cost of sheet glass /frosted film & sun control film shall be measured and paid separately )

S&F powder coated aluminium window and ventilator shutters, side hung type without sash bar, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws, 2 Nos hinges 100 mm long, suitable handle(1 No) etc complete all as specified and as directed. (Cost of sheet glass/frosted film & sun control film shall be measured and paid separately)

M & L double action floor spring for aluminium doors hydraulically regulated made up of minimum1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including necessary cutting & making good to floor as per existing complete all as specified and directed. Make - Kelwyn / Amar

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premisses complete all as specified and directed.

M&L for durastone heavy duty coloured vitrified tiles 300x300x9-10 mm thick exterior grade set and jointed with neat cement slurry and painted in coloured or white cement to match complete all as specified.

S&F Urinals for male of size 355mmx345mmx535mm with complete fitting and spreader, waste pipe etc and fixed on wall complete all spd and directed.

S&F Urinals for famale with complete fitting and spreader, waste pipe etc and fixed on wall complete all spd and directed.

S&F PVC wall pannelling on wall and fixed on wall complete all spd and directed.

M&L 25mm thick PCC 1:2:4 type B-0 (using 12.50mm graded stone aggregate), as in floor including finishing the surface rough & even for receiving kota/tiles complete all as specified and directed .

Taking down door shutter of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, & kitchen cupboard shutters with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing all as spd.. Make approved by GE..

S & F 200 mm long Aluminium anodised barrel tower bolts of extruded section.

S & F Aluminium handles of extruded section, fabricated type and fixed 150 mm long complete all as specified and directed.

S&F Steel ventilator with top hung shutter including, hinges, peg stay, lugs (MS hold fast) complete all as spd and directed

S&F white vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and as directed.

S&F in repair brass chromium plated health faucet for EWC with 15 mm dia PVC pipe 1.00 m long including nut/washer complete all as specified and directed.

S&F in repair 15 mm bore swan neck pillar taps for counter top WHB cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly-nuts screwed for iron pipe & fixed complete.

S&F in repair angle cock 15 mm bore fancy type brass chromium plated, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe.

S&F in repair cast copper alloy CP two way angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule complete.

S&F vitreous china WHB size 550x400 mm white flat back including pvc waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etccomplete all as specified and directed.

M&L for 18 mm thick granite slab (of any type) work (table rubbed and polished) in cooking platforms, steps, window cills, incl edge moulding & cutting holes for gas pipe through drill machine and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete.

S&F in repair toilet paper holder brass, chromium plated all as directed

M&L for RCC as in kitchen platform, shelves & chajjas etc type B1 1:2:4 (20 mm graded stone aggregate) including necessary form work complete.

S & F 450 mm long PVC connection with two Nos. PTMT nuts internally threaded and PVC washer suitable for 15 mm bore pipe line complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints, laid in wall/floors, trenches complete

Dismantling water tanks and removing to store of capacity exc 250 and n exc 500 ltrs all as spd.

S&F 15mm dia Tubes, ‘medium grade’ galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors including cutting /chasing in walls etc. including taking up or down steel tubing and connections complete all as specified and as directed

S&F 20 mm dia Tubes, ‘medium grade’ galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors including cutting /chasing in walls etc. including taking up or down steel tubing and connections complete all as specified and as directed

S&F rolled mild steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410W Grade E 250 complete all as specified and as directed.

Taking down cement plaster from wall/ceiling/roof etc including raking out joints, hacking for key and scrubbing down with water etc all as specified and directed.

M&L 5 mm thick rendering on fair faces of bk /concrete surfaces as on ceiling in CM (1:3), finished even and smooth (without using extra cement ) complete.

M & L for preparation of newly plastered surfaces of ceiling and applying 2 mm thick wall care putty including preparation of new surface complete.

M & L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat primer complete all as specified and directed.

M&L 150mm dia Reinforced concrete pipes, class NP2, laid and jointed on concrete bed, Jointing and testing complete with collars all as specified and directed

S&F Vitreous china urinal half stall type, white with grating and union for discharge pipe incl providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and incl 60mm long brass screws, pointing around urinal back in cement ; fixing automatic flushing cistern with brackets, flush pipe, waste pipe, pvc connection grating, CP spreader and union for discharge pipe complete.

S&F 10mm toughned Glass partion for urinal of size 310mm x 700mm complete all as specified.

Taking down carefully copper / aluminium point wiring (light, fan, switch,socket or power, Bell & Two way point) complete with fitting such as switches, sockets, ceiling rose,sketch light fittings etc, and making good the disturbed surface of walls and floors etc complete all as specified and directed.

Taking down carefully main switches DB's/ MCB DB's and making good the disturbed surfaces of walls etc complete all as specified and directed.

Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls as directed.

M & L for Point wiring with PVC insulated and PVC unsheathed electric FRLS cable of 1100V single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area & including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good disturbed surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit on surface will be used) & 1.5 sqmm green PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs including 1.6mm thick anodised pressed steel sunken box covered with 3mm thick hylum sheet for mounting switches, sockets, fan regulators etc for one light/fan point controlled by one switch complete all as specified and directed.

All as per item no 140 above but one bell point controlled by one bell Push

All as per item no 140 above but one 5 Amps socket out let point controlled by one switch on same board with other switches.

All as per item no 140 above but one 5 Amps socket out let point on independent board controlled by one switch.

All as per item no 140 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board. Make of cable: Polycab/Havell's/Finolex and Make of PVC conduit: Plaza/Harsh/Kalinga Premium/AKG.

Supply and fixing switch piano flush button single pole one way 5 amps, 240 Volts complete all as specified and directed.

Supply and fixing socket outlet flush type 5 Amps, 5 pin, 240 Volts complete all as specified and directed.

Supply and fixing switch piano flush button single pole one way 15 Amp 240 volt complete all as specified and directed.

Supply and fixing in socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 240 volts complete all as specified and directed.

Supply and fixing bell push single pole, 6 Amps, 240 Volts, flush type complete all as specified and directed.

Supply and fixing for electronic Fan regulator 450 watt step type complete all as specified and directed.

Supply and fixing Ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

Supply and fixing for batten/angular fittings complete all as specified and directed.

Supply and fix LED Lamp 7/8 watt complete all as specified and directed.

Supply and fixing double door TPN DBs four way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral & DB's will be fitted concealed in wall / surface as per site required complete all as specified and directed .

Supply and fixing double door SPN DBs eight way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed .

Supply and fixing with MCB SPN 5 to 40 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed .

Supply and fixing MCB SP 240 volts 5 to 32 Amps, 10 KA breaking capacity, 'C' type including connection with suitable size aluminium / copper lugs complete all as specified and directed .

Supply and fixing MCB TPN 50 to 63 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed .

Supply and fixing LED tube light batten box type with decorative end caps suitable single tube 1x 18/20 watt T8 lamps type complete with LED tube rod 18/20 Watt internally pre wired and fixed to wall/ceiling incl fittings accessories connecting up with twin core twisted flexible copper conductor cable suitable size all as specified. Make- Havells/ Bajaj/Philips/ CG.

Supply and fixing LED bulk head 10 watt fittings environmental friendly ultra modern energy saving surface mounted decorataive bulk head fitting with electronic driver and prewired and necessary electric connection with PVC insulated twin twisted flexible copper wire of size 0.75 Sqmm complete all as specified and as directed. Make: Crompton/Bajaj/Havells.

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof recessed ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed. Make, Havells / Philips / Bajaj / Crompton Greaves

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers and grouting with nut , bolts & Fastenar on the wall and make good the disturbed surface and electric connection with 1.5 Sqmm three core PVC insulated round flexible copper wire upto ceiling rose complete all as specified and directed . Make: Crompton/ Bajaj/Havells/Usha.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete Make: Havells /CG/PHILIPS/BAJAJ

M & L for security wall light bracket made out of GI pipe light grade 25 mm dia 1.2 metre length bent to shape and reduced to required size at top upto 1.5 metre length by cutting, welding and well finishing including MS clamp of flat iron of size 40x6 suitable length 2 sets complete with drilling, hole, fixing with nuts bolts and washers including painted with two coats of aluminium paints over a coat of red oxide primer including dismantling one complete all as specified and as directed.

S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed

M&L for Sub main wiring two single core PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in but excluding non metallic rigid PVC conduit including PVC insulated unsheathed 4.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly complete.

Taking down fan, ceiling fan and dismantling blades and removing fan and blades to store and after cleaning refixing the same with replacement of multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal over hauling the fan complete all as specified and as directed.

Supply and fixing of down rod for ceiling fan made out of 15 mm dia MS pipe complete with holes, and MS strip clamp with slotted or threaded upto 1.5 m long all as per site requirement specified and directed by Engg-in-charge.

Supply and fixing of Earthing to panel with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to galvanised earth lead wire 4.0mm dia by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead strip protected by GI pipe 40 mm dia light grade and connected to earth test point including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete

Supply , laying & testing for XLPE underground cable insulated, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing with suitable size aluminium lugs complete of size 16 Sqmm nominal cross section x 4.0core.Make: Havell's/Polycab/KEI/Gloster

M & L dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying and stretching of cable and gentally hand ramming and consolidation of thickness of sand 18 cm all as specified and directed by Engr - in - Charge. Note :- Sand thickness shall be measured 18 cm only .

M&L for bricks cover of old size bricks sub class 'B' with width equal to the length of the brick laid dry & flet abutted with with each other with gap between adjacent bricks n.exc 10 mm over UG cable for protection compete.

Supply and fixing of GI tubing, light grade, 40 mm bore with all fitting lais in trenches / pole / wall for protection of cables in repairs complete.

M/s Naresh Chand Agrawal

jaglalchoudharyandsons

M/S Priya Trading Agency

HARINANDAN RAI SONS

M/S SAMRAT TRADING AGENCY

SINHA CONSTRUCTION

M/S SAROJ KUMAR SINGH