PROVN OF GD ROOM ALONGWITH WASHROOM FOR CORPS MILITARY POLICE CMP GATE PROVN OF TOILET BLOCK NEAR HELIPAD GROUND GUARD POST AT AUNDH MILITARY STATION AND PROVN OF PARKING SHED NEAR BLDG NO T6 BDE URC OF HQ 330 INF BDE UNDER GE MH RH KHADKI

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft and loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 mtr in depth and getting out in soft/loose type of soil complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25cm in soft/loose soil complete all as specified and directed.

Removing surplus excavated material (soil) to distance not exc. 50 mtr and depositing where directed at a level not exc. 1.50 mtr above the starting point complete all as specified and directed.

Material and Labour for plain cement concrete, 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Material and Labour for Reinforced cement concrete (design mix) in M-25 20mm graded stone aggregates in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Material and Labour for Reinforced cement concrete (design mix) in M-25 20mm graded stone aggregates in Columns, pillars, piers, posts and struts complete all as specified and directed.

Material and Labour for Reinforced cement concrete (design mix) in M-25 20mm graded stone aggregates in roof Beams, cantilevers, bressummers, lintels over 1.5mtr span complete all as specified and directed.

Material and Labour for Reinforced cement concrete (design mix) in M-25 20mm graded stone aggregates in roof Slab supported in walls beams and columns in roof ,Landing, balconies, deck slabs and in shelves and similar work complete all as specified and directed.

Material and Labour for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and directed.

Material and Labour for Formwork to sides of pillars, posts, struts, piers, columns and stanchions Square, Circular rectangular on plan or polygonal complete all as specified and directed.

Material and Labour for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. on flat rough surface complete all as specified and directed.

Material and Labour for Formwork to soffits of suspedded slabs such as roof slabs, floor slabs landings and similar work, vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

Material and Labour for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra lime or cement) complete all as specified and directed.

Material and Labour for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra lime or cement) complete all as specified and directed.

Material and Labour for rendering 10mm thick in cement mortar 1:3 on ceiling surface, finished even and smooth without using extra cement complete all as specified and directed.

Material and Labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Material and Labour for mild steel TMT bars 8 mm to 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Material and Labour for Precast cement concrete block masonry 1:3:6, type C1 (20mm graded stone aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as specified and directed.

Material and Labour for PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate), as in lintels upto 1.5 mtr clear span, cills, steps,seismic and other similar bands, plinth course, string courses, lacinng courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

Material and Labour for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

Material and Labour for Hardcore of broked stone or boulder gauge exc 63mm but n. exc 100mm, deposited, spread and levelled in layers n.exec 15 cm thick, watered and rolled/rammed to a tue surface complete all as specified and directed.

Material and Labour for 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) in sub base of floor is to be rough finished complete all as specified and directed.

Material and Labour for 75mm thick, PCC (1:3:6), Type C-1, using 20mm graded stone aggregate as in Plinth protection etc surface finished even and fairwithout using extra cement including necessary form work if required, provision of vertical joints at 2 mtr centre to centre complete all as specified and directed.

Material and Labour for Non Skid ceramic tiles 7mm to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick in CM (1:6) Screed bed or bedding layer of mortar for laying floor finishes complete all as specified and directed.

Ditto all as in item No. 25 above but as in skirting /dados including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Material and Labour for Non Skid Ceramic tiles, Coloured, of size exceeding 0.06 Sqm and not exceeding 0.18 Sqm, 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:6 complete all as specified and directed.

Material and Labour for Glazed Ceramic tiles, Coloured, of size 300mmX600mmX7mm as in Vertical Surfaces such as Skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including backing coat of 10mm thick in cement mortar 1:4 in complete all as specified and directed.

Material and Labour for 20mm thick Granite work (table rubbed and polished) in steps, jambs, cills, cooking platforms,counter tops and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 20mm Screed bed in CM 1:4, all as specified and directed. Note : The rate quoted is deemed to be included for full moulding of edges and making, opening for kitchen sink complete all as specified and directed.

Supply and Fixing aluminium louvered ventilators of section size 100mmx25mmx1.50mm including 4 mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh 0.36 mm nominal dia of wire and average width of aperature 1.40 mm fixed type on outside frame etc. complete all as specified and directed.

Supply and Fixing mild steel work in framed work such as grills framed guard bars, gratings, ladders etc with ends of bars shouldered and / or riveted or forged into spikes and similar work (Fe290 Gde E-165) complete all as specified and directed.

Supply and Fixing Powder coated aluminium window sliding type (3 track) with frame size100mm x 35mm x 1.2mm and shutter 39.40mm x 17.70mm x 1.2mm with tow glass shutter & one mesh shutter incl necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm plain float glass & 0.36 mm dia SS wire mesh, 1.40 mm average width of aperature, fittings etc complete all as specified and directed.

Supply and Fixing Pressed steel frames size of 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

Material and Labour For PCC 1:3:6, type C0, (12.5 mm graded stone aggregate) in door and windows frames, any size, single or double rebated, including arrangement for fixing of hinges and fixtures as required complete all as specified and directed.

Material and Labour for flush shutters 30mm thick solid core constructions with block board core , ply wood face panels commercial type on both side complete all as specified and directed.

Supplied and fitted to chowkats 35 mm thick second class Hardwood factory made Gauzed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a) complete all as specified and directed.

Supply and Fixing Solid PVC door frame of size 50mm X 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube in opening of Sintex or its equivalent make as approved by Accepting Officer complete all as specified and directed.

Supply and Fixing Factory made solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in frame at site as per specification & drawing of Sintex or its equivalent make as approved by Accepting Officer complete all as specified and directed.

Supply and Fixing Aluminium anodised barrel tower Bolt of size 150 mm size of extruded section complete all as specified and directed.

Supply and Fixing Aluminium cast type anodised Handle, size 150mm long complete all as specified and directed.

Supply and Fixing 100 mm size, heavy weight Butt Hinges, cold rolled, Stainless steel including fixtures complete all as specified and directed.

Material and Labour for new plaster surface applying two or more coats Wall Care Putty having average minimum thickness of 3mm of on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper over and including one coat of alkali resistant primer on walls complete all as specified and directed.

Material and Labour for preparation of new plaster surface of ceiling with steel wire brushes and removing smoke spots, moulds, efflorescent salts including filling of spots with POP , chalk whiting priming and applying three coats of white wash complete all as specified and directed.

Material and Labour for complete removal of existing treatment, preparing the surfaces and applying two coats of Finishing walls with Premium Acrylic Smooth exterior emulsion paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)® upto 2 storey complete all as specified and directed. Make: Asian/Berger or equivalent

Cutting chases, pinning in concrete block walls, making good to facing where required and pointing in cement mortar (1:3) and making good , cutting n.exc 10cm girth complete all as specified and directed.

Supply and Fixing 15 mm bore tubes, medium grade, galvanised, with all fitting & fixed complete to walls & ceiling or laid in floors, complete all as specified and directed.

Supply and Fixing 20 mm bore tubes, medium grade, galvanised, with all fitting & fixed complete to walls & ceiling or laid in floors, complete all as specified and directed.

Supply and Fixing Toilet paper holder Chromium plated brass fancy type with gold effect finishes complete all as specified and directed. (Make :Hindware/Cera/Prayag or equivalent).

Supply and fixing CP soap dish holder with gold effect finishes complete all as specified and directed. (Make :Hindware/Cera/Prayag or equivalent).

Supply and Fixing two way Bib cock 15mm dia , fancy type, chromium plated with capstan or butterfly handle with gold effect finishes , screwed down, screwed for iron pipe or for brass ferrule and suitable for 15mm bore of pipe fixed complete all as specified and directed.

Supply and Fixing towel ring chromium plated brass fancy type with gold effect finishes complete all as specified and directed. (Make :Hindware/Cera/Prayag or equivalent).

Supply and Fixing sheet glass shelf assembly consisting of 5.5 mm thick sheet glass 12 cm wide with CP bracket guard and railing 60 cm long complete all as specified and directed.

Supply and Fixing Corner glass shelf with 200mm dia or above with stainless steel hinges and chromium finish holders/wall of approved make complete all as specified and directed

Supply and Fixing CP brass angular stop cock 15 mm dia with gold effect finishes complete all as specified and directed.

Supply and Fixing CP brass, chromium plated shower roses with or without swivel joints with gold effect finishes, any size, including fixing to steel pipe or union complete all as specified and directed. (Make :Hindware/Cera/Prayag or equivalent).

Supply and Fixing PVC connection of 450 mm length, suitable for 15 mm bore pipe with PTMT nuts, complete all as specified and directed.

Supply and Fixing PVC connection of 600 mm length, suitable for 15 mm bore pipe with PTMT nuts, complete all as specified and directed.

Supply and Fixing bathroom cabinet mirror (of approved pattern) of size 450mmx 350mm regular size with mirror and PVC shelves complete all as specified and directed.

Supply and Fixing tubular towel rail 20mm dia, D type 60cm long between flanges brass chromium plated with gold effect finishes, complete all as specified and directed.

Supply and Fixing health faucet chromium plated (ABS Body) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook fixing to 15 mm bore of pipe with gold effect finishes complete all as specified and directed.

Supply and Fixing 15mm Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed with gold effect finishes complete all as specified and directed.

Supply and Fixing CP grating ring or frame square or round 100mm size complete all as specified and directed.

Supply and Fixing wash down water closet ( European type) excluding fixing bolts, flushing cistern, & flush pipe but including connecting to existing out let pipe etc complete all as specified and directed.

Supply and Fixing PVC valveless syphonic action type flushing cistern (Low level) of 10 litre capacity, coloured with inlet ball valve, float, handle including fixing brackets and 32 mm bore PVC flush pipe etc complete all as specified and directed.

Supply and Fixing vitreous china wash basin white, flat back of size 450mm x 300mm, excluding taps, waste chain & plug & porcelein stopper but including brackets, cutting for and pinning in ends of brackets complete all as specified and directed.

Supply and Fixing pillar taps fancy type cast copper alloy with capestan heads chromiun plated screwed down high pressurewith hot &cold with long screwed shanks and fly nuts complete all as specified and directed.

Supply and Fixing CP Peg set of four of Brand- Hi-life,make-KPS Sanitation(P)Ltd, (Economy classic Series) or equivalent of Prayag/Cera/Parryware complete all as specified and directed.

Supply and Fixing PVC (SWR) bends any radius bore of 75 mm complete all as specified and directed.

All as per items No 69 here in before but 110mm bore etc complete all as specified and directed.

Supply and Fixing of PVC (SWR) pipes of 75mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors/ wall complete all as specified and directed.

Supply and Fixing of PVC (SWR) pipes of 110mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floors/ wall complete all as specified and directed.

Supply and Fixing Rotational moulded Polythene [HDPE] Water Tanks, Cylindrical & Vertical Type 1000 Liters Capacity double layered 'ISI' marked, hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and directed.

Supply and Fixing Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

Supply and Fixing 20mm dia bore Gun metal, globe or gate valves with Iron wheel head, screwed both ends for Iron pipes and fixed complete all as specified and directed.

Supply and Fixing 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms) complete all as specified and directed.

Supply and Fixing for decorative/fancy type powder coated aluminium pipe 25mm dia and 2mm thick as in curtain rod fixed to brackets (shade and design as approved by GE) complete all as specified and directed. (Note : Brackets shall be measured and paid separately )

Supply and Fixing decorative/fancy type powder coated aluminium brackets fancy type for curtain rods complete all as specified and directed.(shade and design as approved by GE)

Material and Labour for applying roof treatment complete all as specified and directed as under :- (i) Providing 10mm thick (average) rendering in cement mortar 1:3 mixed with WPC as per manufacturer's instruction (to be measured separately as supply only) for levelling to a true surface and to receive new roof treatment complete. (ii) Providing a coat of bitumen primer @ 0.40 Litre/Sqm over plastered surfaces of roof including parapet surfaces. (iii) Providing one layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm, reinforced with polyester non woven fabric (weighing not less than 150 Gms/Sqm). Polymeric membrane shall be taken to a height 60cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Note:(a) Laying of APP based polymeric membrane shall be done by torch application method or as per manufacturar's instruction. (b) Side overlaps shall be minimum 75mm and end laps shall be minimum 100mm and sealing all overlaps and joints as manufacturer's instructions. (c) The make of polymeric membrane shall be as per PS Specification of CA. (iv) Applying two coats of bituminous aluminium paint on top of APP membrane.

Excavating over areas, n exc 1.5 mtr deep and getting out n.exc 10 Sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Removing excavated material to a distance n. exc. 50 mtr and depositing where directed at a level n. exc 1.50 mtr above the starting point complete all as specified and directed.

Material and Labour for providing, precast cement concrete 1:2:4 set in cm 1:6, type B1, (20 mm graded stone aggregate) in window or door cills, lintels, bressummers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, kerb stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc.(of any section indicated), with plain fair faces, including chamfers weatherings, throating etc. and setting in mortar complete all as specified and directed.

Material and Labour for broken stone hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Material and Labour for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

Material and Labour for 80mm thick coloured Pre-Polished machine pressed interlocking rubburised and glossy finish paver block any shape and size conforming to IS 15658-2006 of M-40 Grade laid complete all as specified and directed.

Excavation in trenches not exc. 1.5 mtr wide and not exc. 1.5 mtr in depth and getting out in hard/dense soil complete all as specified and directed.

Removing excavated material/soils to a distance exc. 50 mtrs and not exc. 250 mtrs, depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and directed.

Material and Labour for 150mm dia RCC drain pipes class NP2 laid in trenches and jointed with in cement mortar complete all as specified and directed.

Material and labour for cement concrete bed in 1:3:6 type C2 (Using 40 mm graded stone aggregate) to drain pipe including packing under and haunching against the sides of the pipe after they are laid and tested for the 150 mm bore of pipe complete all as specified and directed.

Material and labour for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in benching inside manholes and copping including all necessary form work complete all as specified and directed.

Material and labour for precast RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) in cover slabs set in cement mortar 1:6 including all necessary form work complete all as specified and directed. Note : Reinforcement shall be measured and paid separately.

Material and Labour for round steel bar 10 mm dia cut to length bent to required shape for manhole cover handle complete all as specified and directed.

Supply and Fixing Aluminum aodised sliding door bolts, bearing ISI mark, 300mm long with hasp and staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

Material and Labour for applying two coats of cement base paint on plastered surfaces of walls including preparation of new surface complete all as specified and directed.

Material and Labour applying three coats of white wash to newly plastered surface of ceiling including preparation complete all as specified and directed.

Material and Labour applying two coat of oil bound distemper over a coat of primer to newly plastered surface including preparation of new plastered surfaces to wall complete all as specified and directed.

Supply and Fixing Vitreous China Squatting pan Orissa pattern long pan, size 580 mm X 440mm white with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including concrete complete including making good to floor complete all as specified and directed.

Supply and Fixing in repair Vitreous china wash hand basin (550mm X 400mm) white with pedestal , flat back excluding taps but including brackets & CP waste coupling 32mm, LDPE waste pipe 32mm upto floor complete all as specifed and directed.

Supply and Fixing Vitreous china Urinal half stall type white, with grating and union for discharge pipe fixed icluding all reqd necessary fittings as instructions of manufacturers, bottal trap , fixing to existing wall complete all as specified and directed. Make : Jaquar/ Cera/Hindware/ Parryware or equivalent.

Supply and Fixing PVC (SWR) branch piece 110 mm bore, single Y equal or unequal complete all as specified and directed.

Supply and Fixing PVC (SWR) junction 110mm bore single T equal or unequal complete all as specified and directed.

Supply and Fixing Powder coated Aluminium grill of approved pattern using channel of required size, screwed to windows & ventilators with self tapping screws complete all as specified and directed.

Supply and Fixing Rotational moulded Polythene [HDPE] Water Tanks, Cylindrical & Vertical Type 500 Liters Capacity double layered 'ISI' marked, hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and directed.

Supply and Fixing (any type & size of door) aluminium anodised door with frame and including shutter and glazing with 5 mm thick tinted glass or 12 mm thick prelaminated particle board exterior grade in panels, rubber gasket, aluminium glazing clips, mortice lock, Aluminium stopper cleat, hydraulic double action floor door spring, iron mongary etc. section of aluminium door including powder coating of any colour (min thickness of powder coating 50 micron) shall be of following sizes:- Frame : 100mm x 44mm x 1.80 mm thick with rawal plug Middle lock rail: 100mm x 44mm x 1.80 mm thick Bottom rail : 100mm x 44mm x 1.80 mm thick Top rail / Style: 46mm x 44mm x 1.80 mm thick Glazing beading: 0.70 mm thick Aluminium handle 'D' type: 150 mm long Aluminium tower bolt 9.9 mm dia shoot 200 mm long Mortice lock – 100 mm 4 lever, Aluminium stopper cleat Note :- (i) Making good of wall surface with matching to existing surface complete all as specified and directed. (ii) Making good floor surface after fixed hydraulic double action floor door spring with matching to existing surface complete all as specified and directed.

Excavating in post holes ( or similar hoels ) each n exc 0.5 cum getting out, returining, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm , watering, and removing surplus soil to a distance n exc 50 mtr complete all as specified and directed.

Material and Labour for plain cement concrete in foundation, filling and mass concrete type B-2 1:2:4 (using 40 mm graded stone aggregate) complete all as specified and directed.

Supply and Fixing Joist channel, angle, MS pipe or tee sections fixed independently, without conneted plated etc (Fe290 Gde E-165) complete all as specified and directed.

Material and Labour for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

Supply and Fixing Plates (plain or chequered) channels, square cut or notched (ordinary & counter sunk) forming holes, without any attachment GDE Fe 410-0 Gde E-250 complete all as specified and directed.

Supply and Fixing Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut, but length of bolts exc 5cm but n exc 10cm long of Diameter of shank 11mm to 15mm complete all as specified and directed.

Supply and Fixing Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and Fixing Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over and including a coat of red oxide or zinc chrome primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

Material and Labour for point wiring complete with 1.5 Sqmm single core FRLS-H PVC insulated unsheathed cable 1100 V grade multi stranded copper conductor drawn through and including non metallic rigid PVC conduit and accessories concealed in walls/ceilings including 1.5 Sqmm dia multistranded copper cable as earth continuity conductor connected to common earth dolly, including 1.22 mm thick pressed steel terminal boxes to provision of Modular switches to house switch/regulators etc including Modular Plate and Covers for one fan/light /bell point controlled by one switch/bell push complete all as specified and directed.

All as per item No 115 above but for one 3 pin 5 Amps socket on same board controlled with other switch on same board complete all as specified and directed.

Supply and fix modular switch 1 way 6A 1 module complete all as specified and directed.

Supply and fix modular socket 6A 2/3 pin combined 2 module complete all as specified and directed.

Supply and fix modular socket 16A 2/3 pin combined 2 module complete all as specified and directed.

Supply and fix modular switch 1way 16A 1 module complete all as specified and directed.

Supply and fix ceiling rose surface bakelite with three terminals complete all as specified and directed.

Supply and fix Modular fan regulator 120 watts stepped type 2 module complete all as specified and directed.

Supply & fix LED fitting for Bldg security, 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 / 66 protection complete. including conncting with 0.5 sq mm copper condector 3 core flexible cable from fitting connector to ceiling rose and fix on wall with clamps & nut bolts and necessary GI bracket made of 32 mm light grade GI pipe of 1 mtr lenth with necessary bending complete all as specified and directed.

Supply and fixing LED lights fitting 1 x 22W, 220V, AC, decorative box type with driver, holder incl LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED Light fitting mirror type with high output diffuser 2 feet , 1 X 10 watt 220 V AC decorative type with driver holder and LED lamp, Alluminium housing, including connecting up with flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing Lamp holder PVC/polycarbonate type with back plate suitable for batten fitting including LED bulb of 15 watts complete all as specified and directed.

Supply and Fixing MCB DB SPN 12 way of any size and capacity double door type horizontal with 200A busbar including disconnecting from mains and making good the disturbed surfaces complete all as specified and directed.

Supply and Fixing MCB SP of capacity 5A to 32A "B' curve complete all as specified and directed.

Supply and Fixing MCB, SPN (Double Pole) 40 amps, 240 Volts, 10 KA ‘’C” curve complete all as specified and directed.

Supply and fix in industrial wall mounted plug socket suitable fotr IP 44 degree of protection of 20Amps rating 1P+N +E complete all as specified and directed. Make: L&T/C&S/Legrand/Indoasian

Material and labour for Water heater storage type of capacity 25 liters vertical type wall mounted including 15 Amp/ 16 Amps plug top with suitable wall supports and for manual operation, digital temperature display, feather touch buttons, built in thermostat, auto shut off, powder coated single line weld container with PUF insulation, heating element capacity of 2 KW, voltage rating 230 Volt, frequency 50 Hz, 5 star rated with and including steel braided connecting hoses of required length for Hot and cold water pipe, connecting to CPVC and GI pipe complete all as specified and directed. Make: Havells/Jaquar/Crompton/Bajaj. Note :- (i) The rates are inclusive of all the minor spares (Fasteners, Clamps, Nut bolts washers etc)

Supply and fix Stop Valves , cast copper alloy, screwed down , high pressure with crutch or butter fly handle , screwed both ends for iron pipe or for unions and fixed of size 15 mm complete all as specified and directed.

Material and Labour for earthing with 600mm x 600mm x 6mm galvanised steel earth plate electrode buried vertically in ground (earth pit not less than 2.25 meter deep below normal ground level) with top edge of the plate at a depth of not less than 1.5 mtr below ground level, connected to and including G.I. wire of size 4 mm dia by means of bolts,nuts and check nuts and washers of galvanised steel, GI pipe 15 mm dia light grade pipe for protection of GI earth lead wire both to be provided to the extent of 7.5 metres as earthing lead and connecting to the eqpt/machinery etc. incl charcoal dust and common salt packed all around the earth plate in alternate layer in the earth pit all as per electrical plate No. 3 of SSR Part I-2009 including PCC chamber made up of PCC 1:3:6 type C1 (20 mm graded stone aggregate) & RCC Chamer cover of size 540mm x 540mm x 100 mm made with 1:2:4 Type B1 (20 mm graded stone aggregate) using 6 mm round MS bar & 8 mm MS bar for handle , 20 mm dia medium grade G.I. watering Pipe from top edge of the earth plate upto M.S. funnel with wire mesh provided inside the concrete earth pit for watering arrangement incl excavation and earth work in any type of soil and testing complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator/remote and connected accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC). complete all as specified and directed.

Supply and fix Exhaust fan steel body complete with louvers shutter,frame, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 380 mm complete all as specified and directed. Note : (i) The rates are inclusive of any civil work required to fix the exhaust fan.

Material and Labour for Cutting existing GI pipe of 50 mm dia for insertion of new tees (50x50x20)mm , branches etc. including necessary excavation work complete all as specified and directed.

Supplied and fixed Gun-metal, globe or gate valves with iron wheel head, srewed both ends for iron pipe and fixed for size 50 mm dia complete all as specified and directed.

Material and labour for construction of brick masonry valve chamber of size, 105cm X 105cm x 105cm (internal) suitable for housing sluice valve/gate valve etc with plain cement concrete 1:4:8, type D-2, using 40mm graded stone aggregates for foundation, 100mm thick with 150 mm alround offset from external face of wall, brick work in cement motor 1:6, 230 mm thick, rendering 15mm thick in cement motor 1:4, inside complete and outside 150 mm below ground level, coping with plain cement concrete 1:2:4, type B1 (20 mm graded stone aggregate) including provision of MS sheet cover 3.15 mm thick fixed to MS angle iron frame 40mm X 40mm X 6mm embedded in PCC (1:2:4) type B1 (20 mm graded stone aggregate) concrete with suitable hinges and locking arrangements, including two coats of synthetic enamel paint over a coat of red oxide primer, including necessary excavation and earth work in any type of soil etc complete all as specified and directed.

Supplying, laying, jointing, commissioning and testing XLPE insulated screened PVC bedded, armoured, heavy duty underground electric cable with stranded aluminium conductor 1100 volts grade confirming to IS-7098 (Part-I-1988) laid in trenches/ducts/wall / floor / pipes/ poles including cable glands and aluminium lugs of appropriate size, pvc sleeve etc complete all as specified and directed of size 16 Sqmm 4 core . Make :- Havells / Gloster / Finolex / Polycab (Cable to be laid from nearest LT Panel to TPN DB/Metering panel)

Material and Labour for riddled earth cushioning to under ground cable in trenches / existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed. Note:- Measurement shall be taken after gentling punning.

Material and Labour for Brick " class B "protection for under ground cable complete all as specified and directed.

Supply and Fixing light grade GI pipe of size 40 mm dia conforming to IS 1239 (Part-1): 2004 laid in trenchs or under floors or fixed on pole for cable protection complete all as specified and directed.

Supply and Fixing MCB DB SPN 4 way of any size and capacity double door type horizontal with 200A busbar including disconnecting from mains and making good the disturbed surfaces complete all as specified and directed.

Supply and Fixing MCB, SPN (Double Pole) 32 amps, 240 Volts, 10 KA ‘’C” curve complete all as specified and directed.

Supplying, laying, jointing, commissioning and testing XLPE insulated screened PVC bedded, armoured, heavy duty underground electric cable of size 6 Sqmm 2 core with stranded aluminium conductor 1100 volts grade confirming to IS-7098 (Part-I-1988) laid in trenches/ducts/wall / floor / pipes/ poles including cable glands and aluminium lugs of appropriate size, pvc sleeve etc complete all as specified and directed. Make :- Havells / Gloster / Finolex / Polycab